Manufacturer:
(Category: 108)
3 identical welding machines are available. Very little used. Standard: EN 60974-1, three phase 3~400V 50Hz. Rated values at X 40°C: 5A 10V, 350A 24V 40 percent, 320A 22.8V 60 percent, 280A 21.2V 100 percent for one operating mode, another operating range 5A 20V with 320A 32.8V 40 percent, 290A 31.6V 60 percent and 260A 30.4V 100 percent, U1 = 400V, protection class IP23. It is an inverter controlled TIG MMA welding power source with max. 350A, digital control and memory functions, pulse function adjustable from approx. 0.5Hz to 2kHz, HF or lift ignition, adjustable parameters such as gas pre flow and post flow, slope up and down, balance and various waveforms sinus square etc., PFC technology for high efficiency and operation on generators, remote control or foot pedal connection, thermal monitoring and fault diagnosis with error codes, optional water cooling unit KG 10. An on-site ins ...
A Rehm Invertig Pro 350 AC DC and a Rehm Invertig Pro 450 DC are available, used and in good condition. 1) Invertig Pro 350 AC DC, standards: IEC 60 974-1 IEC 60 974-2, welding current range TIG: 3-350A, output voltage U₂ at maximum current: approx. 24V, open circuit voltage U₀: approx. 91V, duty cycle 100 percent for TIG at 350A, mains voltage input: three phase 400V 50Hz, protection class: IP23S, protection category: S, setting range: 3-350A for TIG in this AC DC version, duty cycle 100 percent at 40°C 350A for TIG 100 percent duty cycle, input fuse protection: 32A at 3x400V for the 350 AC DC version, length: 520mm, width: 360mm, height: 460mm, weight: 29.5kg for AC DC version. 2) Invertig Pro 450 DC, standard: IEC 60 974-1, welding current range TIG: 3-450A, output voltage U₂ at maximum current: approx. 28V, open circuit voltage U₀: approx. 91V, duty cycle 100 percent at 450A ...
5 identical welding machines are available. Mains voltage: 400V 50/60Hz, fuse: 25A, power consumption: 22kVA, cos phi: 0.8, setting range: 40-400A, working voltage: 16-34V, open circuit voltage: 19-55V, voltage steps: 2x12. Duty cycle at 40°C: 60 percent at 360A 32V, 100 percent at 250A 26.5V. Protection class: IP23, insulation class: H 180°C, cooling type: F. Weight gas cooled: 153kg, water cooled: 161kg. Length: 1040mm, width: 460mm, height: 935mm. Two coarse steps, 12 fine steps, high performance 4 roll wire feeder 140W, feeding speed: 0.5-24m/min, wire diameter: 0.8-1.6mm, 2 choke outputs for adjustment to the welding task. Control MC 15 as a compact easily exchangeable control box. Functions: wire feed speed constant control, wire creep, burn back time, 2 stroke and 4 stroke, wire inching without current and gas, low noise fan thermostat controlled for gas cooled units, thermal ov ...
- Remote control with frequence - Foot switch control with frequence
- Chuck Table diameter 2940 mm- Tilting 0 - 135 Degrees- Variomatic rotation - Work load @ 1000 mm gravity 50 Ton- Work load @ 1500 mm gravity 32 Ton- Work load @ 2000 mm gravity 27 Ton
consisting of: - Laser welding head in aluminum case - Coaxial extension - Gas pressure reducer for welding gas supply - Operating instructions - Aluminum carrying case 5300_2 - WSweld Starter Kit Starter Kit WSweld Consisting of: 3 x Annular gap nozzle 1 x Focusing mirror 1 x Deflecting mirror 1 x ZnSe window Laser welding head TC08 Replacing the cutting head with the WSweld laser welding head TC08 expands a flatbed machine into a laser welding system. Deep penetration and heat conduction welding combined in one optic Active cooling of all optical elements Coaxial welding gas supply for perfect laser weld seams Cross-jet prevents contamination of the optics Active collision detection The WSweld laser welding head TC08 is compatible with the following machine types: TRUMPF TruLaser 3030 classic TRUMPF TruLaser 5030 classic TRUMPF Trumatic L2530 TRUMPF Trumatic L3030 TRUMPF Trumatic L3040 ...
Offer 25156 Mobile Extraction Turbine Specifications: - Volume flow approx. 240 m³/h. - Connection socket 50 mm -Drawer - Collection container - Drive power 400 V / 1.5 kW - Required space W 1000 x H 1500 x D 650 mm - Weight approx. 120 kg
Inv. Num. : 8672 Type: IR-SA Producer: Tiesse Created: 2008 Parameters: Number of axles: 6 pieces Maximum load capacity: 10 kg The workstation consists of: Kawasaki FA-10L Robot (FD40 Control) P2OV Positioner Fronius TPS 5000 welding machine (MIG-MAG) Complete accessories and wiring
Model: BAS 051. Automatic Flash Butt Welding Machine for Band Saw Blades. Pneumatic clamping. Annealing pyrometer. Inserting bar for blade positioning. UniOp automatic annealing temperature control. Machine cleaned and repainted. Year of manufacture: 2001. Nominal primary voltage: 380 [V AC]. Max. welding rating: 8 [kVA]. Clamping force: 20 [kN]. Forging force: 5 [kN]. Welding ranges. Band saw blades for wood: 6-50 [mm]. Bi-metal bandsaw: 6-41 [mm]. Hoop knives: 6-50 [mm]. Stainless steel bandsaw: 6-30 [mm]. Weight: 600 [kg]. Dimensions (WDH): 135010001700 [mm]. Instructions and packing included.
Used welding equipment As seen in the pictures, technical data See pictures. If you have any further questions, please Price is per piece
AXXAIR orbital welding system was built in 2020 in France. The system, designed to weld tubes with a maximum diameter of 220 mm, proves itself wherever the highest quality, repeatability and cleanliness of joints are required. The mechanised orbital welding is performed using the TIG method, in which a torch with a non-fusible tungsten electrode moves around a stationary workpiece. The use of this solution guarantees welds of the highest quality, repeatability and cleanliness. The orbital welding system on offer is fully complete and consists of the following parts: – orbital welding power source AXXAIR SAXX-210 – open head for orbital welding SATO-220E41 – orbital cutting machine AXXAIR CC222 Technical specifications of the individual components of the AXXAIR orbital welder Power source - single-phase network with earthing - supply voltage 110-230 V ± 15% - input cur ...
AXXAIR orbital welding system was built in 2020 in France. It is an extremely easy-to-use and efficient solution for precision welding of tubes with a maximum diameter of 170 mm. The mechanised orbital welding is performed using the TIG method, in which a torch with a non-fusible tungsten electrode moves around a stationary workpiece. In this way, welds of the highest quality, repeatability and cleanliness are produced. The orbital welding system is offered with all the necessary components including – orbital welding power source AXXAIR SAXX-210 – open head for orbital welding SATO-170E41 – orbital cutting machine AXXAIR CC172 Technical specifications of the individual components of the AXXAIR orbital welder Power source - single-phase network with earthing - supply voltage 110-230 V ± 15% - frequency: 50/60 Hz - input current consumption (at 230 V): 25 A - input c ...
Ref.nr. 00886 Name of the system: Portal mesh welding machine Manufacturer Fibro GSA Made in Germany Model GAE 516 Year of construction 2008 Nameplate: Connected load 630 kVA Primary voltage 400V Nominal frequency 50-60 Hz Fuse 800A Specifications: Nominal primary voltage 400V/ 50 Hz Control voltage 24 V/DC Number of transformers 10 pieces Nominal power per transformer at 50% ED 63 kVA Connected load at 50% ED 630 kVA Fuse L1+L2+L3 (Lmax 90m) 800 A Supply cable cross-section L1 + L2 + L3 (Lmax 90m) 2x240 mm2 Supply line to the machine PE 1x240mm2 Supply cable PC 230V 10A 3x2.5mm2 Electrode force 480 N/bar Air pressure – connection G 3/4 Air pressure min. 6 bar Air consumption at 80 cycles / min 600 Nl/min Cooling water connection inlet G 2.0 Cooling water connection outlet G 2.0 Cooling water consumption 92 l/min Cooling water pressure min. 3 ba ...
Ref.Nr. 00885 Name of the system Mesh welding machine CE Manufacturer: IDEAL Werk - Lippstadt IDEAL 05 small Model GAE 112 Year of manufacture 2004 Revised in 2021. Diode package and transformers replaced, cables cleaned worth €32,000 Activity / Description – spot welding semi-automatic Rated power at 50% ED 2x200kVA Connected load 400kVA Primary voltage 400V Open circuit voltage 7V Nominal frequency 50-60 Hz Fuse 800 A Made in Germany Specifications: Nominal primary voltage 400 / 50 V / Hz Control voltage 24 V/DC Number of transformers 2 pieces Nominal power per transformer at 50% ED 200 kVA Connected load at 50% ED 400 kVA Fuse L1+L2 800 Amp Fuse L3 63 Amp Supply cable cross-section L1 + L2 + L3 (Lmax 90m) 2 x 240 mm2 Supply cable cross-section L3 125mm2 Supply line to the machine PE 240mm2 Supply cable PC 230V 10A 32.5mm2 Electrode ...
current capacity: . kVAthroat: . mmcontact pressure capacity: . kpdimensions: ca. 650 x 800 x 2050 mmweight of the machine ca.: 140 kgThis spot welding machine with state-of-the-art Inverter 125L technology enables the welding of high-strength sheet metal and allother steel sheet parts. The multi-purpose machine with water cooling is ideal for all intensivework under heavy loads.DESCRIPTION:- Welding machine for all spot welding and alignment work- Pneumatic clamping tongs with strong tension(strength at electrodes)550 N at 7 bar with electrode arms of 100 mm- 2.5 m water-cooled cable for the clampand 3 m air-cooled cable for the gun- Current compensation- Telescopic arm with equalizer- Pneumatic clamp with remote control- 78 welding programsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
container turning device, welding turning device, welding turning device, welding device, welding turntable, welding turntable and tilting table, welding turning device, welding turntable tilting table -Handover: in current condition as viewed -Condition: without drive motors / control, see photos -Welding rotating device: pivoting -Turntable: Ø 700 mm -Projection: 930 mm -Transport dimensions: 1240/730/H1640 mm -Weight: 643 kg
Laser power: 4kW, working area X/Y/Z: 4000mm/2000mm/115mm, max. sheet thickness mild steel/stainless steel/aluminium: 20mm/15mm/10mm, max. workpiece weight: 1700kg. Machine dimensions X/Y/Z: approx. 11600mm/5300mm/2200mm, weight: approx. 15000kg. Includes Trumpf Liftmaster. Documentation available. An on-site inspection is possible.
Specifications: Procedure: 2-stage Filter area: approx. 17 m² Separation efficiency: >99% Welding Fume Separation Class: W3 Extraction capacity: 1100 m³/h Diameter of extraction arm: 150 mm Length of extraction arm: 3 m Power connection: 3 x 400 V Motor power: 1.1 kW Sound pressure level: 70 dB(A) Dimensions, approx.: 785 x 730 x 950 mm Weight, approx.: 106 kg Characteristics: - Made in Germany - For low to medium smoke/dust quantities - Suitable for occasional to frequent use - Convenient filter change through maintenance door - Extraction hood can be rotated and swivelled 360 degrees Equipment: - 3 new replacement main filters (original price approx. 330 euros each) - 7 new replacement pre-filters - 2 extraction hoods (one of them unused)
Travel path X/Y/Z: 3000mm/1500mm/115mm, laser power: 5000W, cutting capacity mild steel/stainless steel/aluminium: 25mm/20mm/12mm, travel speed: 200m/min, cutting accuracy: 0.1mm. Machine dimensions X/Y/Z: 11000mm/4600mm/2400mm, weight: 12000kg, control: Siemens Sinumerik 840D. Includes conveyors, laser cutting heads with various lens sizes, Liftmaster R, and other peripheral equipment. Documentation available. An on-site inspection is possible.
Remote control for inert gas welding device, inert gas device, welding rectifier, hand controller-Manufacturer: Fronius, remote control RCU5000i Univ.SD-Art.No.: 4,046,098-Voltage: U1 24 V-Dimensions: 180/260/H50 mm-Weight: 1.5 kg
Inv. Num. : 8642 Type: ROMAT 350 ROTOL Producer: CLOOS Created: 2007 Parameters: CLOOS Welding Robot Workstation allows welding in the MIG/MAG process alternately at three workstations. Currently, only two are used: One is equipped with a two-axis positioner for fixing the welded part with the possibility of a horizontal axis of rotation with support the second is equipped with the same positioner without support the third workstation is not equipped with a positioner. For an optimal work process, 11 programming axes are available.
A complete plasma cutting system Oerlikon including peripheral equipment is available. 1) CNC plasma cutting system Oxytome 30, year of manufacture: 2008. 2) Plasma source Air Liquide Nertajet HP125, year of manufacture: 2008. 3) Filter unit Donaldson Torit DCE DFPRO 8-Cyclo, year of manufacture: 2008, weight: approx. 1625kg. 4) Cooling unit Air Liquide Friojet-30, year of manufacture: 2008, cooling capacity: 2kW, max. operating pressure: 29.5bar, refrigerant: R407c, weight: 80kg. Documentation available. An on-site inspection is possible.
table diameter: 340 mmtable load: 160 horizontal kg.table load: 100 vertikal kg.swivelling range: 0 - 90 Gradturning speeds: 0,6 - 6,0 U/minbore: 60,0 mmmotor: 230 Voltweight of the machine ca.: 56 kg.range L-W-H: 385 x 340 x 375 mmFurnishing:- The table can be adjusted at an angle of 0 to 90 degrees tilt and jam- Start / stop via a location-independent foot switch.- Direction of rotation can be selected right / left.- Adjustable rotation time- The turntable has a 60 mm hollow shaft- The turntable has a diameter of 340 mm. The surface is chrome-plated for Protection against welding spatter.- The table speed is adjustable from 0.6 - 6 rpm.- The control of the welding machine via the turntable control is possible.- The ground contact transmits 300 A / 100%.- The turntable and the control are separate.- HF protected.- COM 1800 control with lap welding- Operating instructions in GermanFu ...
total power requirement: 230 Volttable diameter: 300 mmtable load: 100 Horizontal kgswivelling range: 0 - 90 Gradturning speeds: 0,2 - 2,0 U/minturning speeds: 1,2 - 12,0 U/minbore: 20,0 mmweight of the machine ca.: 50 kgdimensions of the machine ca.: 480 x 325 x 470 mmFurnishing:- Precise drive unit with face plate, on a stable floor stand.- clockwise / counterclockwise- 2 speed series, stepless- Swivel range from 0 ° - 90 °. Manual tilt- DC gear motor with worm gear, infinitely variable.- diameter of 300 mm. Chrome-plated surface to protect against weld spatter.- The devices control panel is easy to understand and use.- Start / stop via a location-independent foot switch.- The speed and direction of rotation are set on the machine.- HF protected.Scope of delivery:- control (integrated)- foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cutting range for steel to: 12.0 TS mmcutting range for steel to: 8.0 QS mmcapacity at 100%: 30.0 Amperecutting medium: Druckluft output: von 20 - 40 Ampereoutput: Eingang 4.9 KWvoltage: 230 Vweight: 17,9 kgrange L-W-H: 480 x 210 x 340 mmThe Avalon 40.1 is a light, handy plasma cutting system with highCutting performance and top cutting quality. Their light weight and simplicityHandling makes them the ideal candidate for crafts, workshops andIndustry. Cuts carbon steel, stainless steel, aluminum, copper...Characteristics- IGBT technology- Active PFC technology for high duty cycle and energy efficiency- Manual switch to activate airflow to test air pressure. without having to trigger the burner.- Powerful compact system- Intelligent protection function protects the plasma torch from damage such as incorrect air pressure, missing wearing parts, overloading of the. pilot arcmax. separation ...
cutting range for steel to: 15.0 TS mmcutting range for steel to: 10.0 QS mmcapacity at 100%: 25.0 Amperecutting medium: Druckluft output: von 20 - 40 Amperevoltage: 230 VAir consumption: 230 l/min.output: Eingang 4.9 KWweight: 8.0 kgrange L-W-H: 505 x 147 x 305 mmThe Avalon 40.1 is a light, handy plasma cutting system with highCutting performance and top cutting quality. Their light weight and simplicityHandling makes them the ideal candidate for crafts, workshops andIndustry. Cuts carbon steel, stainless steel, aluminum, copper...Characteristics- IGBT technology- Active PFC technology for high duty cycle and energy efficiency- Manual switch to activate airflow to test air pressure. without having to trigger the burner.- Powerful compact system- Intelligent protection function protects the plasma torch from damage such as incorrect air pressure, missing wearing parts, overloading of the ...
Innovac GmbH
