Manufacturer:
(Category: 301)
Extruder, co-rotating twin screw extruder, twin screw extruders, plastic injection molding machine -Engine power: 55 kW -Screw diameter: 51.7 mm -Speed: 60-400 rpm -Dimensions: 1250/4530/H1080 mm -Weight: 3000 kg
Ref. no.: 18588Hersteller: BATTENFELDYear of construction: 2007Clamping unitClamping force: 30 tonDistance between tie bars: 300 x 300 mmMould height min.: 150 mmMould height max.: 330 mmOpening width: 580 mmPlaten size (h x v): 450 x 450 mmInjection unitScrew diameter: 18 mmInjection volume: 19 cm³Shot weight: 17,5 gInjection pressure: 2500 barMeasurements and weightDimensions: 3,5 x 1,1 x 1,9 mMachine weight: 2700 kg
Clamping Force: 100 Ton Holding force: 110 Ton Maximum opening stroke: 380 mm Minimum mould height: 200 mm Maximum mould height: 430 mm Distance between plates: 610 mm Plate size: 600×600 mm Distance between columns: 420×420 mm Maximum weight supported: 700 kg Extraction stroke: 100 mm WEMO manipulator NOT included. MORETTO receiver-hopper NOT included. WITTMANN granulate dispenser NOT included. SESOTEC metal detector NOT included. Screw diameter: between 25 and 35 mm - not accurately detected. Warning: the information reported has been taken from the manual and may not correspond to actual performance. For further information, on-site inspection is suggested. Approximate body dimensions: 4800 × 1900 × 2600 mm. The item is sold in the state in which it is, unverified and without warranty of operation. Item not subject to sales restrictions. Auction-ID: A7-44316-700
Clamping Force: 160 Ton Maximum opening stroke: 450 mm Mould height: between 250 and 550 mm Distance between plates: 1000 mm Plate dimensions: 795x795 mm Distance between columns approx.: 520 x 520 mm Maximum weight supported: 1110 kg on the moving plate. Extraction stroke: 200 mm MORETTO Receiver-Hopper NOT included. With WEMO manipulator With SESOTEC metal detector Screw diameter: between 25 and 35 mm - not accurately detected Warning: the information reported has been taken from the manual and may not correspond to actual performance. For further information, on-site inspection is suggested. Approximate dimensions of the machine body: 5700×1600×3500 mm. The item is sold in the state in which it is, unverified and without warranty of operation. Item not subject to sales restrictions. Auction-ID: A7-44316-697
Clamping Force: 100 Ton Holding force: 110 Ton Maximum opening stroke: 380 mm Minimum mould height: 200 mm Maximum mould height: 430 mm Distance between plates: 610 mm Plate size: 600×600 mm Distance between columns: 420×420 mm Maximum weight supported: 700 kg Extraction stroke: 100 mm Screw diameter: between 25 and 35 mm - not accurately detected. MORETTO hopper receiver and dispenser NOT included. With YASHIN manipulator With DEMAG jib crane and hoist with a capacity of 500 kg and approx. 1500 mm of reach. Warning: the information reported has been taken from the manual and may not correspond to actual performance. For further information, on-site inspection is suggested. Approximate body dimensions: 4800 × 1900 × 2600 mm. The item is sold in the state in which it is, unverified and without warranty of operation. Item not subject to sales restrictions. Auction-ID: A7-443 ...
Clamping Force: 50 Ton Holding force: 50 Ton Maximum opening stroke not detected Minimum mould height not detected Plate Spacing Not Detected Plate size: 450× 450 mm Distance between columns: approx. 370× 370 mm Maximum supported weight not detected Extraction run not detected Screw diameter: between 25 and 35 mm - not accurately detected Fully electrically driven press, with servo-hydraulic nozzle unit. Warning: the information reported has been taken on board the machine with measuring instruments and may not correspond to the actual performance. For further investigation, on-site inspection is suggested. Manual NOT present. Approximate body size: 4300×1250×1800 mm The item is sold in the state in which it is, unverified and without warranty of operation. Item not subject to sales restrictions. Auction-ID: A7-44316-689
Clamping Force: 100 Ton Holding force: 110 Ton Maximum opening stroke: 380 mm Minimum mould height: 200 mm Maximum mould height: 430 mm Distance between plates: 610 mm Plate size: 600×600 mm Distance between columns: 420×420 mm Maximum weight supported: 700 kg Extraction stroke: 100 mm MORETTO receiver-hopper NOT included. WITTMANN granulate dispenser NOT included. SESOTEC metal detector NOT included. Screw diameter: between 25 and 35 mm - not accurately detected. Warning: the information reported has been taken from the manual and may not correspond to actual performance. For further information, on-site inspection is suggested. Approximate body dimensions: 4800×1900×2600 mm. The item is sold in the state in which it is, unverified and without warranty of operation. Item not subject to sales restrictions. Auction-ID: A7-44316-699
CAUTION This lot consists of 9 DEMAG injection moulding machines, EXCLUDING all the elements mounted on the machines, such as MORETTO manipulators, metal detectors and receivers and WITTMAN equipment. The following list includes only the presses: 698 - DEMAG - ERGOTECH 1000-310 - Plastic injection moulding machine - 1998 696 - DEMAG - ERGOTECH 1000-310 - Plastic injection molding machine - 1998 695 - DEMAG - ERGOTECH 1000-310 - Plastic injection molding machine - 1995 693 - DEMAG - ERGOTECH 1000-310 - Plastic injection moulding machine - 1995 692 - DEMAG - ERGOTECH 1000-310 - Plastic injection molding machine - 1995 688 - DEMAG - ERGOTECH 1000-310 - Plastic injection moulding machine - 1995 687 - DEMAG - ERGOTECH 1000-310 - Plastic injection molding machine - 1995 686 - DEMAG - ERGOTECH 1000-310 - Plastic injection molding machine - 1997 685 - DEMAG - ERGOTECH 1000-310 - Plastic inj ...
Clamping force: 800kN, Opening stroke: 450mm, min. tool installation height: 250mm, Plate dimensions X/Y: 660mm/560mm, Tie bar spacing: 403mm/345mm, Ejector stroke: 100mm, Injection volume: 154cm³, Injection pressure: 1600bar, Machine dimensions X/Y/Z: approx. 6000mm/1850mm/2000mm, Weight: approx. 4900kg. An on-site inspection is possible.
Serial number: X42252 Machine type: Injection Moulding Machine Clamp unit: 400T (Tonnage Group G0 400T–450T) Injection unit: 5600 Injection Specifications: - Screw Ø: 97 mm - Screw type: GP mixing for G - Intensification ratio: 9.42 - Max. shot weight (PS): 253 g - Injection capacity (cm³): 3394 - Injection rate: 550.4 cm³/s - Max. screw stroke: 450.2 mm - Max. hydraulic injection pressure: 170 bar - Specific injection pressure: 1600 bar Clamping Unit: - Tie bar spacing: 750 mm × 750 mm (H × V) - Mould height: 300 – 885 mm - Max. platen distance: 1605 mm - Location ring Ø: 175 mm - Location screw (MX): M20 - Core pulling: 2 sets Power Requirements: - Voltage: 400 V - Drive power: 124.3 kW - Heating wattage: 44 kW - Total power: 168.3 kW - Current requirement: [Not specified] Robot: ATM ES2000 Max. water heater temperature: 95 °C Machine dimensions: 9600 × 2200 mm Machine ...
Electrical injection moulding machine manufactured in 2021. This ZHAFIR ZERES III 3000 / 830 / B5 features a clamping force of 3000 kN and a maximum mould opening stroke of 600 mm. It includes a platen size of 1040 x 1040 mm and a screw diameter of 50 mm. If you are looking to get high-quality injection moulding capabilities, consider the ZHAFIR ZERES III 3000 / 830 / B5 machine we have for sale. Contact us for further details.
Awaiting refurbishment at our headquarters in Northamptonshire is this BOY 22A injection moulding machine. Any machines awaiting refurbishment (or undergoing refurbishment) with us can be reserved with a 10% deposit and we then prioritise the refurbishment and aim to have the machine available for inspection within 8 weeks from order. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Prices shown are ex-works, but we can quickly provide DAP (Delivered at Place) Incoterm pricing on request. We can take out the hassle and add ...
Hydraulic injection moulding machine manufactured in 2007. This Engel Victory VC1800/300 P features a clamping force of 3,000 kN and an opening stroke of 900 mm. It includes a robust control system with a 15 TFT touchscreen and a maximum injection pressure of 1,735 bar. If you are looking to get high-quality injection moulding capabilities, consider the Engel Victory VC1800/300 P machine we have for sale. Contact us for further details. Identical Engel Victory VC 1800/300P (2008 model) also for sale â same configurations.
Electrical injection moulding machine manufactured in 2017. This Negri Bossi ELE 80 features a clamping force of 800 kN and a maximum opening stroke of 515 mm. The machine offers a tie bar distance of 420 Ã 420 mm and a platen size of 595 Ã 595 mm. If you are looking to get high-quality injection moulding capabilities, consider the Negri Bossi ELE 80 machine we have for sale. Contact us for further details.
Electrical injection moulding machine manufactured in 2015. This FANUC Roboshot S100iA features a closing force of 100 tons and a screw diameter of 26 mm. With a beam spacing of 460 x 410 mm, it is designed for efficient production. If you are looking to get high-quality injection moulding capabilities, consider the FANUC Roboshot S100iA machine we have for sale. Contact us for further details.
Hydraulic injection moulding machine manufactured in 2013. This Krauss Maffei 35-180 CX features a plasticising size of 180 and a screw diameter of 28 mm. With 3 units available, consider the opportunity to buy this Krauss Maffei 35-180 CX hydraulic injection moulding machine. Contact us for further details.
Hydraulic injection moulding machine manufactured in 2008. This FERROMATIK K- TEC250S features a clamping force of 2500 kN and an injection volume of 441 cm³. It has a screw diameter of 50 mm and a tie bar spacing of 630 Ã 630 mm. If you are looking to get high-quality injection moulding capabilities, consider the FERROMATIK K- TEC250S machine we have for sale. Contact us for further details.
Arburg 820S 4000-2100/400 / Production line with the Sepro Industrial Robot SR S5-35 S3 Trans robot / Operating hours: 42,014 h in automatic mode Year of manufacture: 09.2012 Injection unit: Screw diameter: 60 mm Injection weight: 723 g Spray pressure: 2500 bar Dosing volume: 792 ccm Clamping unit: Clamping force: 400 t Tiebar spacing: 820x820 mm Size of the clamping plates: 1171x1171 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: 2K Injection Molding Machine with Turntable and Robot Very good technical condition Operating hours: 42,014 h in automatic mode Euromap 67 Robot interface Air Valve x 6 Hydraulic, needle-core pull, controlled by a proportional valve x 4 pairs Control with hot runners x 24 Reinforced Injection Units – Bimetal Proportional valve on vertical injection unit – precise injection ...
Arburg 1500T 3200-1300 e² / Hybrid machine with a turntable Year of Make: 2011 Injection unit: Screw diameter: 60 mm Injection weight: 607 g Spray pressure: 2000 bar Dosing volume: 664 ccm Clamping unit: Clamping force: 320 t Spar spacing: 0x0 mm Size of the clamping plates: 1510 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Hybrid machine: high-speed, energy-saving and very quiet Operating hours: approx. 30,000 in automatic mode Euromap 67 Robot interface Control with air valve Hydraulic core pull x 3 Control with hot runners x 13 Hardened injection unit - Bimetal Main motor of the machine – servo motor driven by inverter Very precise rotary table, driven by a servo motor, controlled by an inverter Rotary table diameter: 1500 mm Horizontal injection unit with automatic injection height adjustment ...
Arburg 630S 2500-1300 ECO / Production line with the Sepro Industrial Robot SDR 22S Year of Make: 2008 Injection unit: Screw diameter: 55 mm Injection weight: 521 g Spray pressure: 2380 bar Dosing volume: 570 ccm Clamping unit: Clamping force: 250 t Tiebar spacing: 630x630 mm Size of the clamping plates: 900x900 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Euromap 67 Robot interface Air Valve x 4 Hydraulic core pull x 2 Control with hot runners x 15 Hardened injection unit - Bimetal Machine with cylinder / battery with compressed nitrogen (extra charge for fast working) ECO – the machine has a system for adjusting the minimum tool height Robot - Sepro Industrial Robot SDR 22S Year of Make: 2016 4-axis robot: 3 axes are driven by servo motors (electric); Axis C - pneumatic Traversing in axes: X-150 ...
Key data: 2000 kN
Arburg 570H 2000-800 e² / Hybrid machine / Production line with the Arburg Multilift Select robot Year of Make: 2011 Injection unit: Screw diameter: 50 mm Injection weight: 359 g Spray pressure: 2000 bar Dosing volume: 392 ccm Clamping unit: Clamping force: 200 t Handlebar spacing: 570x570 mm Size of the clamping plates: 795x795 mm Ejector: electric Clamping unit: toggle lever Control: SELOGICA - Touchscreen Additional equipment: Hybrid machine: energy-saving and very quiet Euromap 67 Robot interface Air Valve x 4 Hydraulic core pull x 2 Control with hot runners x 12 Hardened injection unit - Bimetal Main motor of the machine - Servo motor driven by inverter - Energy saving The injection unit is driven by the servo motor, which is controlled by an inverter Machine with cylinder / battery with compressed nitrogen (extra charge for fast working) Central lu ...
Arburg 570S 2200-290/100/100 / Production line with the Wittmann W823 robot / Operating hours: 20,499 h in automatic mode Year of Make: 2016 Injection unit: Screw diameter: 35 mm Injection weight: 132 g Spray pressure: 2000 bar Dosing volume: 144 ccm Clamping unit: Clamping force: 220 t Handlebar spacing: 570x570 mm Size of the clamping plates: 795x795 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: 3-component injection moulding machine, high-speed Very good technical condition Operating hours: 20,499 h in automatic mode Euromap 67 Robot interface Air Valve x 6 Hydraulic, needle-core pull, controlled by a proportional valve x 4 Control with hot runners Hardened injection unit - Bimetal Proportional valve on the injection unit – precise injection Machine with two cylinders / battery with compressed ni ...
Arburg 570C 2000-350/150 / Production line with the Arburg Multilift side robot / 2K machine Year of Make: 2003 Injection unit: Screw diameter: 40 mm Injection weight: 153 g Spray pressure: 2120 bar Dosing volume: 182 ccm Clamping unit: Clamping force: 200 t Handlebar spacing: 570x570 mm Size of the clamping plates: 795x795 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA Additional equipment: Production line with the Arburg Multilift side robot 2K Machine Air Valve x 1 Hydraulic core pull x 5 Control with hot runners Reinforced Injection Units – Bimetal Proportional valves on sprinkler units - precise spraying The vertical injection unit - screw diameter: ⌀25 mm - 49 g/hp All offered machines are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected machine o ...
Key data: 1600 kN
Arburg 520S 1600-400/170 e² / Production line with the Geiger robot Year of Make: 2012 Injection unit: Screw diameter: 35 mm Injection weight: 141 g Spray pressure: 2500 bar Dosing volume: 154 ccm Clamping unit: Clamping force: 160 t Tiebar spacing: 520x520 mm Size of the clamping plates: 695x695 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: 2K injection moulding machine with rotary table and robot Geiger Very good technical condition Hybrid machine: energy-saving and very quiet Euromap 67 Robot interface Air Valve x 4 Hydraulic core pull x 5 Control with hot runners x 12 Reinforced Injection Units – Bimetal Machine with two cylinders / batteries with compressed nitrogen (extra charge for fast work) Parallel movements Screw diameter in vertical injection unit: ⌀30 mm - 77 g/hp Built-in Arburg c ...
Key data: 1500 kN
Arburg 520H 1500-400 e² / Hybrid machine Year of Make: 2011 Injection unit: Screw diameter: 40 mm Injection weight: 184 g Spray pressure: 2000 bar Dosing volume: 201 cc Clamping unit: Clamping force: 150 t Tiebar spacing: 520x520 mm Size of the clamping plates: 695x695 mm Ejector: electric Clamping unit: toggle lever Control: SELOGICA - Touchscreen Additional equipment: Hybrid machine: energy-saving and very quiet Euromap 67 Robot interface Core train control Control with hot runners x 8 Hardened injection unit - Bimetal Main motor of the machine - Servo motor driven by inverter - Energy saving The injection unit is driven by the servo motor, which is controlled by an inverter Machine with cylinder / battery with compressed nitrogen (extra charge for fast working) Central lubrication Parallel movements Priamus Sensor - Tool Pressure Control Dimension ...
Arburg 520H 1500-400 e² / Hybrid machine Year of Make: 2011 Injection unit: Screw diameter: 40 mm Injection weight: 184 g Spray pressure: 2000 bar Dosing volume: 201 cc Clamping unit: Clamping force: 150 t Tiebar spacing: 520x520 mm Size of the clamping plates: 695x695 mm Ejector: electric Clamping unit: toggle lever Control: SELOGICA - Touchscreen Additional equipment: Hybrid machine: energy-saving and very quiet Euromap 67 Robot interface Air valve x 4 on the side of the fixed clamping plate Air valve x 3 on the side of the movable clamping plate Hydraulic core pull x 1 on the side of the fixed clamping plate Hardened injection unit - Bimetal Main motor of the machine - Servo motor driven by inverter - Energy saving The injection unit is driven by the servo motor, which is controlled by an inverter Machine with cylinder / battery with compressed nitroge ...
Arburg 470C 1500-400 Year of manufacture: 07.2009 Injection unit: Screw diameter: 45 mm Injection weight: 232 g Spray pressure: 1580 bar Dosing volume: 254 ccm Clamping unit: Clamping force: 150 t Spar spacing: 470x470 mm Size of the clamping plates: 650x650 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Core train control Hardened injection unit - Bimetal It is possible to change the screw diameter Dimensions: Weight: 4790 kg Length/Width/Height: 4.44x1.63x2.09 m Drive: Pumps/motor: 18.5 kW Heating capacity: 9.4 kW Total power: 27.9 kW All offered machines are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected machine or to participate in live technical tests at our company in Łódź. Price: On request
Key data: 1500 kN
Arburg 470C 1500-400 Year of manufacture: 07.2009 Injection unit: Screw diameter: 45 mm Injection weight: 232 g Spray pressure: 1580 bar Dosing volume: 254 ccm Clamping unit: Clamping force: 150 t Spar spacing: 470x470 mm Size of the clamping plates: 650x650 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Core train control Hardened injection unit - Bimetal It is possible to change the screw diameter Dimensions: Weight: 4790 kg Length/Width/Height: 4.44x1.63x2.09 m Drive: Pumps/motor: 18.5 kW Heating capacity: 9.4 kW Total power: 27.9 kW All offered machines are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected machine or to participate in live technical tests at our company in Łódź. Price: On request
Arburg 470C 1500-400 with the Wittmann W711 robot Year of Make: 2008 Injection unit: Screw diameter: 45 mm Injection weight: 232 g Spray pressure: 1580 bar Dosing volume: 254 ccm Clamping unit: Clamping force: 150 t Spar spacing: 470x470 mm Size of the clamping plates: 650x650 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Euromap 67 Robot interface Air Valve x 1 Hardened injection unit - Bimetal Proportional valve on the injection unit – precise injection Robot Wittmann W711 Year of Make: 2007 4-axis robot: 3 axes are driven by servo motors (electric); Axis C Traversing in axes: X-420, Y-1200, Z-2000 Touch control panel The safety package for robots Robot with adapter Purchase of the robot at an additional cost Dimensions: Weight: 4900 kg Length/Width/Height: 4.44x1.63x2.09 m Drive: Pumps ...
Formplast GmbH
3.900 € 
