Manufacturer:
(Category: 302)
GALA UNDERWATER PELLETIZER, Type SLC 6, Polymer diverter-valve with hydraulic-pack, die-plate 24 x Ø 3,2 mm ( 5° ), 6-arm knife-holder, By-Pass-System, GALA TWS water-box, heating power 12 kW installed, Water-pump 5,5 kW, GALA Spin-dryer 16,2 BF with 4 kW, Blower 1,1 kW, Siemens Control Cabinet Xantex ( MAAG )
COUMPOUNDING LINE type AD-S 75, - Including twin screw extruder with 2x72 mm co-rotating parallel segmented screws L/D 48, - screws design can be chosen, - Max screw speed up to 600 rpm., - 250 kw a.c.drive, - n.3 venting points, 1 with 3,0 kw vacuum pump, including condensate collector, - 2x side feeders type ZSB (twin screw) 1 x 0,62 mm. each one a.c.3,0 kw drive, including hopper loader with internal stirring unit ( for anti-bridging of additives / fillers as powders, fibers, … ), - Water cooling/tempering unit for cylinder-barrels,, - incl. tank, Temperature-sensor, circulation-pump and heat-exchanger, - semi-automatic, non-stop 2-piston screenhanger, - hydraulic unit, - Siemens PLC with touch screen (EN+DE) and ABB main control board., installed power - used power in work: about 60-65% : 250, availability: 2 months ca, options available: strand OR water ring OR underwater pelle ...
COPERION TWIN SCREW COMPOUNDER, Extruder with 2 x 65 mm. 40 L/D parallel co-rotating screws, 2x side-feeders, 90 kW a,c, drive, vacuum degassing pump, fitted with aa strand pelletizer (can be fitted with a water ring or an underwater pelletizeer), Control-board
CDM PREALPINA RECYCLING EXTRUDER, Materials PE PP PC PS ABS PA, extruder with 130 mm. screw diam., Constructed in 2006, crammed feeding unit, extruder 130 mm., a.c. 283 kw drive, one degassing pump 5,5 kw, semi-automatic, non-stop hydraulic screen changer 230 mm diam.screens, hydraulic power station, water ring pelletizing unit, drying centrifuge, heat exchanging unit, vibrating screen, electric cabinet, machine reconditioned, installed power - used power in work: about 60-65% : 283, options available: different pelletizer, with or without buffer silo, with blower + bag filling station with vertical mixer, capacity: 500-600 kg/h depending on material and feeding rate, conditions: reconditioned (or as is)
COPERION TWIN SCREW COMPOUNDER, Extruder with 2 x 75 mm. 40 L/D parallel co-rotating screws, 2x side-feeders, 132 kW a,c, drive, vacuum degassing pump, fitted with aa strand-pelletizing equipment (can be fitted with a water ring or an underwater pelletizeer), Control cabinet, installed power - used power in work: about 60-65% : 132 kw, options available: water ring OR underwater pelletizer, conditions: reconditioned, type: compunder
ERMAFA AGGLOMERATOR, SPS-System: Siemens S5 – 95U, Average throughput rate:, LDPE: 500kg, OPP: 300-400kg, TPO: 300-400kg, Including:, buffer silo with automatic filling of the agglomerating chamber through pneumatic system, automatic discharging of agglomerated material, Agglomerator, 355 kw drive, Control system, Control cabinet, Extraction system/filter, Classifier, small conveyor belt, Spare parts available:, 1x knife shaft, 35 knifes, Other spare parts need to be produced., Constructed in 1993, used by Constructor for test purposes until 2006, The machine has been working until 3rd quater 24, then disconnected in Feb 25 (after video), installed power - used power in work: about 60-65% : 355, availability: immediate, capacity: 300-500 kg/h depending on materiale and feeding rate, conditions: good working conditions
CINCINNATI CMT 35 APC, twin conical screw extruder, 2x35 mm screws, Control panel, 7,1 kw drive, 57.000 working hours, installed power - used power in work: about 60-65% : 7,1, type: PVC
TECNOVA 130 mm. SINGLE SCREW EXTRUDER, Buffer silo, Forced feeding system, Materials LDPE, LLDPE, HDPE, Screw diameter 130 mm, Single degassing pump, semi-automatic, non-stop hydraulic screenchanger for Ø 250 mm screens, oleodynamic power station, water ring pelletizer, drying centrifuge in stainless steel, vibrating screen, Electric cabinet with air conditioning, Nominal throughput rate 500-600 kg/h depending on materials and feeding rate, Machine offered reconditioned with warranty
TECNOVA RECYCLING EXTRUDER for BIO - PE PP ABS PC PS, Barrel with 90 mm screw diam. 37 L/D, Crammed feeding unit, Is working with BIO at 70 rpm yielding 270 kg/h, with PE at 100 rpm yelds 120 kg/h, N.1 degassing point, hydraulic screenchanger, water ring pelletizer from Gamma Meccanica, drying centrifuge, rotating classifier, electric cabinet for omplete management of the line, availability: 4 weeks for reconditioning or 1 week for AS IS, capacity: 120-270 kg/h, conditions: reconditioned, type: 90 mm. crammed feeder for light scraps
TECNOVA RECYCLING EXTRUDER, for PE PP PS PC ABS, Barrel with 130 mm screw 54 L/D, as new screw and barrel, n.2 degassing pumps for slightly moist or heavy prints, hydraulic screenchanger, hydraulic pack, water ring pelletizer, drying centrifuge, electric cabinet for complete management of the line, in need of reconditioning, capacity: 500-600 kg/h, conditions: reconditioning needed, type: 130 mm. 54 L/D 2xdegassing points 500-600 kg/h nominal throughput rate
Haul-off for profiles, used and overhauled Manufacturer: Blake Type: 303-1600-180 Year of construction: 1995/2021 Serial-No.: 637 Contact length., effective: 1600 mm Gum pad width: 180 mm Design: smooth gum pads at the bottom and top Haul-off force: approx. 20,000 N Haul-off speed: 0.1 -5.0 m/min. Drive Motor: DC Shunt Motor Motor power: 5.0 kW Dimensions: 240 x 90 x 175 cm (LxWxH) Weight: approx. 950 kg Remark: The electrical control cabinet was renewed in 2021. The machine has been cleaned, repainted and checked for function. In addition, a new control panel as a remote control incl. 10 m long control cable.
Key data: 63 mm, 1300
Twin screw extruder, conical Manufacturer: Reifenhäuser Type: BT 1000-2-63 K Year of construction: 1994 Serial No.: 32061 Working hours: 32,303 h Screw geometry: conical for PVC-hard profiles Screw diameter: 63 – 121 mm Screw length: 1300 mm Screw speed: max. approx. 32 1/min. Nominal torque of the gearbox: 1000 daNm Dynamic load rating of the return pressure bearing: 103600 daN Engine power: 43.0 kW, Drive motor: Baumüller DC motor Cylinder heating/cooling zones: 4/3 (air cooling with fan) Adapter heating zones: 1 Tool Heating Zones: 5 Temperature control: digital temperature controller (2 x PSG Multipact 88) Max. permissible mass pressure: 500 bar Output capacity: approx. 150 - 200 kg/h for PVC-rigid profiles Accessories: Dosing device and material hopper Extrusion height: 1150 mm Dimensions: 4250 x 1200 x 1750 mm without hopper (LxWxH) Weight: approx. 3000 k ...
MARIS TWIN SCREW CO-ROTATING EXTRUDER, suitable for compounds, recently used for SBS (stirene-butadiene-stirene), barrel with 2 x 58 mm screws 48 L/D - 600 rpm, Max Torque 945 Nm, 450 kg/h average throughput rate (depending on materials and feeding rate), n.1 vacuum degassing pump, 3 kw, 108 kw drive 1.345 rpm, Total installed power 171,5 kw, dry pelletizing unit - can be fitted with Water Ring or Strand or Underwater Pelletizer, vibrating screen, constructed in 2017, offered totally recondiktioned, installed power - used power in work: about 60-65% : 171.5, availability: 8 weeks from confirmatiom, options available: pelletizer - bespoke to project, capacity: 450 kg/h, conditions: totally reconditioned, type: 48 L/D 2x58 mm screws Ø
LEISTRITZ ZSE40HP, Co.rotating twin screw extruder, n.2 screws Ø 40 mm. 36 L/D, max screws speed 600 rpm, A.c.55 kw drive ca., 10 heating zones, Brabender dosing unit, single degassing pump, missing of screenchange - possible addition of fully automatic or semi-automatic screenchanger, 6-strand die head, It was running with ABS PP PE, Throughput rate up to 120 kg/h, Control cabinet with Siemens touch screen, Users manuals and electrical drawings available, Constructed in 2015, the line is offered reconditioned, availability: 6 weeks time, capacity: now 120 kg/h but depending on material, feeding rate and screw conditions, conditions: reconditioned, type: co-rotating compounder
FIMIC RAS 325 BACKFLUSH, fully automatic screenchanger, for back-flush only, so for contamination under 5%, no costs for doctor blades, no cost for laser filter., works with standard mesh, capacity rekated to screening mesh - with a 250 µ mesh, up to 700 kg/h, connected for test, offered totally reconditioned, with new control panel, availability: 4 -5 weeks time, capacity: Max 500-600 kg/h, conditions: totally reconditioned, type: fully automatic - backflush
Previero underwater head cutting system, complete and ready to work on plastic extrusion lines. Brand: Previero For extruder: Ø 130 mm Underwater cutting in stainless steel Main engine: 3 hp (2.2 kW) With 2 water pumps: 2 HP (1.5 kW) each Centrifuge: 1.30 m x Ø 350 mm Centrifugal motor: 5.5 hp (4 kW)
FBM plastic extruder with Ø 120 mm spindle and underwater head cutting. Ideal for recycling and granulation lines. Brand: FBM (Falzoni) Model: ETF 120 V 380/5L Motor: 200 kW (270 hp) L/D ratio: 35 Underwater cutting (PRT, 2006) Includes: force-fed silo Extras: degasser and filter changer Year: 1988
TECOM BLOWN FILM EXTRUDER, for LDPE-RLDPE blends, Contrex feeding, 2 gravimetric components + 1 volumetric dosing units, Screw diam.70 mm 30 L/D, Rotating head, Low neck, 1.600 mm pull off unit, gusseting unit, Cason corona treatment, single color printer (for marks), 1.600 mm double collection frame, BRA 36+ Eurochiller, working width: 1600, availability: February 2026
TECOM BLOWN FILM EXTRUDER, for LDPE -BIO - RLDPE, Contrex feeding, 2 gravimetric + 1 volumetric components, screw diam. 65 mm.30 L/D, Rotating head, Low neck, pull off unit, gusseting units, Cason corona treatment, single color printing unit (for marks), 1.100 mm. double collection frame, BRA 25+ Eurochiller, working width: 1.100 mm., availability: February 2026, PRESENT CONDITIONS: running and testable
PRT WATER RING PELLETIZER, for PE PP PS PC ABS, nominal capacity 600-700 kg/h (tested up to 900 with PS), N.4 cutting blades, N.1 thermoregulation zones, Heating power 8.00 kW, Cutting motor power 4.00 kW, N.1 water pumps, heat exchanging unit, Single water pump power 3.00 kW, Vertical centrifuge power 5.50 kW, Steam vacuum power 0.25 kW, soundproofed discharging cyclon, Total installed power 20.75 kW, constructed in 2006, only 200 worked hours, installed power - used power in work: about 60-65% : 20.75, availability: immediate, capacity: 600-700 kg/h (tested with PS 900 kg/h), PRESENT CONDITIONS: as new, excellent quality, price is less than 50% of a new one
PVC PROFILE EXTRUSION LINE EVC BRAND, single screw extruder with 60 mm 28 LD, constructed in 1998, for 180 mm max width, 44 kw drive, control panel, Calibrating desk 3,7 m.long with 1 x 9 kw.pump, Caterpillar pull off unit, 180 mm wide, saw, 6,0 mt.long discharging table.
CINCINNATI-MILACRON TWIN SCREW EXTRUDER, for PVC profiles, extruder with 2 x 45 mm conical screws, average production 100 kg/h, 14 kw drive, for profiles with max width 250 mm., calibration desk with 2 pumps x 5 kw, caterpillar pull off unit, contact length 1500 mm, width250 mm., planetary saw, collection table, installed power - used power in work: about 60-65% : 14, capacity: 100 kg/h ca, screws: 45 mm. conical
MARIS TWIN SCREW EXTRUDER, Loading hopper for regrinds, Barrel with 2 x 92 mm screws 40 L/D, co-rotating parallel screws for polyolefines, CEAR d.c.motor, N.2 vacuum degassing pumps, 4-plate semi-automatic screenchanger, hydraulic pack, Average throughput rate around 1 Ton/h, Water ring pelletizer, drying centrifuge, Electrical control panel, The machine is offered as is or checked
ICMA S.GIORGIO TWIN SCREW EXTRUDER, for PE PP PS PC ABS, Barrel with 2 x 110 mm co-rotating screws, n.1 vacuum degassing pump, semi-automatic hydraulic screenchanger (possible fully automatic screenchanger), no cuttins, but we can supply STRAND or WATER RING or UNDERWATER, Electric cabinet
TECNOVA EXTRUSION LINE, for PE PP PC PS ABS, BUFFER SILO, screw conveyor, CRAMMED FEEDING UNIT, extruder with 130 mm. screw, 37 L/D, n.1 degassing pump, 200 Kw.a.c.drive, semi-automatic hydraulic screen changer with 220 mm Ø screens, hydraulic power station, water ring pelletizer, drying centrifuge, vibro-classifier, constructed in 2019, the line is offered AS IS or RECONDITIONED, -----------------------------------------------------------, This line can be integrated with, ENGINE PLAST GRANULATOR (in photos), type BA 1.000.550.3, 75 kw drive, 12 mm screen (or bespoke), blower to scrap silo of extrusion line, installed power - used power in work: about 60-65% : 200
Extruders 65-50-50 mm. diam.screws, K DESIGN thickness control, Double collection of 1.800 mm., Average throughput rate 200-240 kg/h, total installed power 350 kw, compressed air consumption 330 l/min, water consumption 10 l/min, air pressure 6-7 bar, min-max line speed 0-150 m/min, motor power 234 kw, resistive power 25 kw, reduction ratio 1/6, ac motor revolutions standard 2300 rpm, Cartridge filter changer, power 6.75 kw, Resistive power 32.6 kw, Die diameter 220 mm, Bubble cooling group, Electric fan power 22 kw, RV ironing motor 2.7 kw, Platform rotation 0.4 kw, Diagonal fans 0.75 kw, Speed 0-150 m/min, Double winder with calender, Total motor power 6kw, Min./Max. diameter of reels 150/900 mm, Max. reel weight 750 kg, installed power - used power in work: about 60-65% : 350, capacity: 200-240 kg/h, working width: 1.800 mm.
TWIN SCREW EXTRUSION LINE, Top Italian Constructor, for PVC both soft and rigid, max infeed 10-12 mm size, forced feeding hopper, dosing unit, 2 parallel, counter-rotating screws 118 mm diam. 25 L/D, pressure control;, nitrided steel barrel with degassing vent 2,2 kW, Barrel heating bands kW 76,00, Extruder cooling barrel motors power 4x 0,37 kw, n.7 Heating zones, Extruder a.c. motor 120 KW, Extruder tot power 205 kw, Extruder average absorbed power 105,00 kW, Extruder rpm 8-45, Lubrication pump 1,50 kW, Electric cabinet with inverter and modem for remote diagnosis, semi automatic screenchanger for PVC, granulating head, die face dry pelletizer, cooling unit, Installation and start up included (boarding and travel costs on Buyers charge), Total installed power: 205 kw - 105 kw average in use
DRY PELLETIZER FOR PVC AND COMPOUNDS Suitable for extruders with production rate up to 200 kg/h, made in sturdy steel and mounted on a frame equipped with wheels for easy disassembly, granulating chamber in horizontal axis, built in stainless steel, quick opening safety device, knife-holder with fluctuating star to reduce knives consumption., self adjusting knives to nozzle by means of a slide system which keeps knives pressed on the die, reducing wear 2,2 kw drive, 3.000 rpm with extra strong bearing and long shaft, cutting die in anti-wear steel with number and Ø of holes bespoke to project. 1,5 kw Venturi blowing system + pipes and cyclone, n.2 thermoregulation areas, knife mounting template, electric cabinet and touch screen control board with modem for remote assistance, 3 mt.cable machine/panel, flange built to design to fit your extruder, heated by ceramic heating elements , temp ...
EREMA 160 EXTRUSION LINE, with power consumption 350kW, Two Gail TK 1000 TG filter screens, agglomerator, Barrel with screw diameter 160 mm., Screw length 6.000 mm ca (2 x 3.000 mm.), Erema semi-automatic screen changer, Capacity 650-950 kg/h depending on materials and feeding rate., granulation head., Construction year 1995, in working conditions, many spares included, installed power - used power in work: about 60-65% : 350
MARIS TWIN SCREW EXTRUDER, Barrel with 2 x 92 mm screws 40 L/D, n.2 vacuum degassing pumps, co-rotating parallel screws for polyolefines, complete with 4-plate semi-automatic screenchanger, hydraulic pack, Average throughput rate around 1 Ton/h, Water ring pelletizer, drying centrifuge, electric cabinet, The machine is offered as is or reconditioned
GERMANPLAST SRL
