Manufacturer:
(Category: 302)
One complete and one partially dismantled extruder system Davis are available. 1) Davis Standard DS-25, power: 6385W, max. melt pressure: 700bar, max. temperature: 315°C. Including 4x screws, 6x bursting discs, Digicolor dryer, platform, screen changer with heating and sealing pack, new cylinder, 3x screw seals, and spare drive motor. 2) Davis Standard DS-20, power: 4500W, max. operating pressure: 700kg/cm², max. temperature: 315°C. Including Conair dryer, 3x screws, screen changer with heating and sealing pack, cast housing, extrusion tool, and spare drive motor. General accessories: various ring heaters, 3x Eurotherm temperature controllers, and 3x Eurotherm pressure sensors. Documentation available. An on-site inspection is possible.
GAMMAMECCANICA TANDEM SYSTEM 125 mm. 950 kg/h double screening, Throughput rate up to 600-950 kg/h ca, depending on material and feeding rate (0,30-0,40 Kwh/kg), Line suitable for the recycling for heavily printed, high humidity and contaminated materials., High performance degassing chamber for removal of up to 10 times more gas and humidity in the melted material compared to other systems (so you can save on the cost of an agglomerator), The line includes :, Loading conveyor belt, tunnel metal detector, automatic compactor, N.2 Dosing unit for masterbatches and more, 1st extruder with 125 mm. screw Ø 28 L/D, 1st degassing point, FIMIC RAS 500 fully aumatic screenchanger, control cabinet, 2nd extruder with 140 mm. screw Ø 18 L/D, 2nd degassing point, BD-PLAST non-stop screen-changer, TDA6 GM water ring pelletizer, heat exchanging unit, vibrating screen, blower, Water treatment unit , ...
EREMA RECYCLING LINE for PE PP, Type RM80E, constructed in 2004, including :, loading bel with metal detector, compactor, extruder 85 mm screw Ø, non-stop hhydraulic screenchanger, water ring pelletizer, sacking station, electric cabinet, availability: immediate, conditions: stored
Material type: LDPE, LLDPE, mLLDPE, HDPE, PP, regranulates Machine dimensions (LxWxH): 16 X 5 X 10.5 m Min/Max final Film width: 900 / 1700 mm Film thickness: 27–200 μm Capacity: Up to 240 kg/h Line speed: 0–150 m/min Screw diameter: 55/65/55 Layer ratio: Up to 25/50/25 % L/D ratio: 30/1 Number of heating zones: 3 for 55 mm and 4 for 65 mm (1 zone per screen) Dosing system: Doteco Grado; 3 units with 4 components each; centralized vacuum pump (added later); all scales fully serviced last year; new software and external touch screen; neck (before extruder) with additional magnets Electronics: Siemens, ABB Software: Macchi's; full control via touch screen (replaced 3–4 years ago) Die head with IBC: 280 mm; 2.4 mm gap (3 heating zones); TE502 model with air ring extension Internal cooling balloon diameter control (IBC) Ultrasonic sensor (1 unit); JET ...
CMG-MAM BLOWN FILM EXTRUDER for LDPE, extruder with screw diam. 80 mm., Production rate about 150 kg/h, die diam. 150 mm. on rotating head, haul off unit width 1.200 mm., corona treatment, winder mm.1.200, max reel diam. 1.200 mm., min/max film width 600/1200 mm
Key data: 2 mm, 17
Twin screw extruder, parallel Manufacturer: Hans Weber Maschinenfabrik GmbH Type: DS 85 Year of manufacture: 1979/2022 Machine No.: 85-399 Screw geometry: for PVC-hard profiles Screw diameter: 2 x 85 mm Screw length: 17 x D Screw speed: max. approx. 30 1/min. Worm torque: 10,000 Nm Motor power: 3.3 - 25.0 kW, Drive motor: Commutator motor Elektra Faurndau Cylinder heating/cooling zones: 4/2 (air cooling with fan) Tool Heating Zones: 8 Temperature control: 12 x digital temperature controller KS 40 (PMA) Accessories: Melt pressure sensor and melt temperature sensor Connected load: approx. 60 kW (without tools) Extrusion height: 1100 mm Output capacity: approx. 150 - 180 kg/h for PVC-hard profiles Accessories: Material funnel and connection flange Accessories: Vacuum pump (1.1 kW) incl. material separator Dimensions: 4500 x 1200 x 2100 mm (LxWxH), incl. material hoppe ...
BANDERA BLOWN FILM EXTRUDER, for PE, Bandera extruder with screw diam.90 mm., 250 mm die diam. on original Bandera head, reconditioned (not the one in photo), a.c. drive with inverter, calibrator, haul off unit, corona treatment, single color small printing group, single winding station with manual discharge 1.200 mm., good overall conditions, availability: immediate, working width: 1.200 mm., conditions: good
GAMMAMECCANICA Compac 125 mm. Construction year 1998 Including Loading conveyor belt, Metal detector, Compactor with driven haul off for reels, master dosing unit Engin Plast, Extruder 125 mm diam. 36 L/D with degassing pump d.c. Ansaldo drive 197 kW, Total installed power 501 kW motor, BD plast non-stop screenchanger diam. 200 mm, hydraulic power station, water ring pelletizer M 8500, Electrical cabinet, Type of machine: GAMMAMECCANICA PLASTIC RECYCLING LINE 125 mm.
PRT RECYCLING EXTRUDER for PE PP PC PS ABS, Extruder with 85 mm screw, 30 L/D, Constructed in year 2000 - very few hours of work, NEW Crammed feeder new 2023 FF85VE, 60 kw Siemens drive 2.200 rpm, Average throughput rate 200 kg/h, depending on materials and feeding rate, Total heaters power 38,6 kw, N.1 vacuum degassing pump, Manual screenchanger, NEW 2023 Water ring pelletizer WF150, Drying centrifuge, Total installed power cutting group 14 kw, Vibro classifier, Total weight about 3 Tonnes, excellent conditions, MATERIALS: PE PP PC PS ABS PS, capacity: ca.200 kg/h depending on materials and feeding rate, availability: ready-to-go
EREMA INTAREMA 906 TE ECO SAVE, construction year: 2017, Throughput rate up to 240 kg/h depending on materials and feeding rate, installed power 110,5 kw, Presently used for PE and PP, compact line including:, loading conveyor belt 6 m.long, 500 m wide, metal detector, Reel feeding unit RZ 50P, compacting unit, extruder with screw Ø 65 mm., 45 kw drive, double degassing unit, Non-stop, double Screen changer: Erema SW 2 134 RTF, water ring pelletizer HG 84 D, Drying centrifuge: GGT 75 A, Water pump, vibro-classifier for granule type GS 1510, Pellet transport system, Double big bag filling station, installed power - used power in work: about 60-65% : 110,5 kw, availability: immediate, options available: mixing-cooling silo, capacity: up to 240 kg/h, conditions: very good, type: compact line from scraps to granule
KRAUSS MAFFEI TWIN SCREW EXTRUDER (photos before reconditioning), Mod.KMD 2-90 KK, used for profiles, n.2 parallel screws diam. 90 mm 20 L/D Max 30.5 rpm, 40 kw d.c.drive, installed power 180 kw, feeding hopper, max production with PVC profile 240 kg/h, complete with control cabinet, Heating 28.5kW,, 5 Zones Heating and 2 Last Barrel Oil Cooling Barrel +1 Zone Adapter 4 Zones Double Die, degassing point, Measures 4.3 L x 1. 2 W x 2.3 (m) H (incl Hopper) ,, Approx.weight 4.3 Ton
AMUT TWIN SCREW EXTRUDER BA86 (photos before reconditioning), n.2 x 86 mm diam. counter-rotating screws (24 L/D with 4.440 worked hours), Siemens d.c. 31 kw drive, N.1 vacuum degassing pump 1,5 kw, Throughput rate up to 180 kg/h with PVC, N.6 heating areas, N.4 cooling areas, Manuals, CE, drawings available, The machine is offered reconditioned, options available: profiles downstream equipment, capacity: 180 kg/h, conditions: reconditioned, type: for PVC
5 layer die head, without extruder and cooling ring Manufacturer: Reifenhäuser Year of manufacture: 2018 Nozzles: 350mm diameter Capacity: 420 kg/h Product examples: Collation Shrink: 16%/14%/40%/14%/16% Standard packaging film 16%/16%/36%/16%/16% Laminating films : 14%/22%/28%/22%/14% The following extruders were mounted: 60/60/90/60/60
MACCHI 3-LAYERS BLOWN FILM EXTRUSION LINE, for LLDPE/LDPE/HDPE, n.3 extruders with infra-red heaters (for energy saving), Screws Ø 65+80+65 mm, n.3 sliding plate screenchagers, Macchi Die head TE5303-IBC-350/500, Available dies Ø 350 and 400 mm gap 1,8 mm., IBC bubble cooling system, dual-flow, carbon fiber air ring, throughput rate up to 800 kg/h depending on material and recipe, 2.400 mm wide oscillating pull off unit, Motorized side gusseting units, Double, 2.350 mm wide fully automatic back-to-back winding station with fully automatic reel change, Max reel Ø 800 mm, including the following:, Tower, E&L Web guide, Gravimetric weight control system Piovan/Doteco, Components blander Shini, Doteco dosing units, Automatic Thickness control Kundig/K-Design Profile gauge control system, Calibrating basket, Martignoni Corona-treatment, N. 8 Air shafts, Constructed under Covid, started in ...
MACCHI 3-LAYERS BLOWN FILM EXTRUSION LINE, for LLDPE/LDPE/HDPE, n.3 extruders with infra-red heaters (for energy saving), Screws Ø 65+80+65 mm, n.3 sliding plate screenchagers, Macchi Die head TE5303-IBC-350/500, Available dies Ø 350 and 400 mm gap 1,8 mm., IBC bubble cooling system, dual-flow, carbon fiber air ring, throughput rate up to 800 kg/h depending on material and recipe, 2.400 mm wide oscillating pull off unit, Motorized side gusseting units, Double, 2.350 mm wide fully automatic back-to-back winding station with fully automatic reel change, Max reel Ø 800 mm, including the following:, Tower, E&L Web guide, Gravimetric weight control system Piovan/Doteco, Components blander Shini, Doteco dosing units, Automatic Thickness control Kundig/K-Design Profile gauge control system, Calibrating basket, Martignoni Corona-treatment, N. 8 Air shafts, Constructed in 2011 started 2012, Ex ...
Sale of KIEFEL KIRION co-extruder from 2006 and 1600 mm wide, with gavimetric and thickness control.
T-Die Serial No.: L 1081-041391 // Calender Serial No.: F 1201-041392 Haul-Off Serial No.: F 1201-041392-T Max. winder speed: 50 m/min Type: Film system 1080 mm usable width Equipment / Additional information: Max. gross output PP up to 1000kg/h with film width up to 1200mm A special feature is the winding system, which can cut narrow films (150 mm - 100 mm) or for example 8 x 175 mm or even 2 x 700 mm one nozzle lip with a max. film thickness of 2mm up to 1000kg/h. Total power consumption: 211 kW/h Main engine power: 250 kW Min. 068 mm film thickness in PS / min. 0.75 mm in PP Maximum calender speed: Max. 50 m/min. mechanically possible Consists of: -Dosing system 5-chamber Maguire -Extruder (160 mm screw) Amut EA 160 // Age: 2003 -Screen changer (for cleaning in food production) -Melt pump -Slot die (1 insert) 120 cm -Lip with max. film thickness up to 2mm up to 1 ...
A complete extrusion line with a Reifenhäuser extruder and a gravimetric system Plast-Control (2006) is available. 1) Unwinder 1. 2) Primer unit and hotmelt unit for water-based adhesive lamination. 3) Dryer. 4) Unwinder 2. 5) Dolci extruder for extrusion lamination. 6) Unwinder 3. 7) Two printing units with additional dryer. 8) Extruder Reifenhäuser. 9) Rewinder. 10) Guide roller in the basement. 11) Web guiding under unwinder 1 in the basement. 12) 2x resin silos in the basement. This is a complete extrusion line with peripheral equipment. Documentation available. An on-site inspection is possible.
R 537: Recycling plasticizer (roller extruder) "MTA" Year 86, drive 200KW, plasticizing capacity approx. 800-1000kg/h, ideal for recycling plastics. The facility consists of the following parts: -Roller extruder -Batcher -Shearing device -Motor 200KW -Engine control cabinet "Schorch" -1 lattice box pallet spare parts FUNCTIONALITY: Ground plastic waste is fed into the plasticizer ------- heating ------- sausage kneading ------- shearing depending on the workpiece weight ------- further processing in presses The recycled plastic waste was used to make large parts such as garbage containers, plastic pallets, benches, flower pots, etc.
Key data: 50 mm
We offer you a EREMA extruder for sale, which has been fully refurbished in-house. It is an INTAREMA® 605K, the machine is completely mechanically and electrically reconditioned by us before delivery, all components that do not meet our criteria are exchanged for original EREMA spare parts. The machine is designed for a throughput of up to 90kg per hour and is suitable for LDPE. If you are interested in this machine, please contact us! Tags: EREMA, UMAC, refurbished, pelletizer, extruder, regranulating machine,
Twin-screw extruder, corrotating, brand: OMC, type: EBV 31/32D, year: 2001. 31 mm Ø composable spindles. Book-type shirt. 11 Kw motor with water-cooled variator and wire head. Total installed power: 25 kw
BAUSANO TWIN SCREW PVC EXTRUSION LINE, Type MD 2-90 B25-HK, barrel with 2 x 90 mm counter-rotating, parallel screws 25 L/D 80% performancees, Hot die-face-pelletizer, vibrating- cooling screen, Spare parts:, 1 set new screws for plasticised PVC, Machinery connected for test-run, availability: 09/25, conditions: running, type: for PVC and UPVC
STEIN Maschinenbau Profile Guillotine PT1-200 For glazing beads, small profiles, main profiles and technical profiles Max. cutting width: 190 mm, max. cutting height: 120 mm Extrusion speed: up to max. 10 m/min Blade length: 600 mm Length accuracy: +/- 2 mm Knife stroke: 180 mm Cutting speed infinitely variable Pneumatic quick-change device for knives Hold-down device pneumatic Knives are preheated: 80ºC - 160ºC Cycle time: 1.5 to 4 sec. adjustable on the display Infeed side: unit for applying a protective film to the profile Control: Compact PLC Siemens S7-613C Dimensions: Height: approx. 1,900 mm, extrusion height: 1,100 mm (+/- 50 mm height adjustment) Footprint: approx. 1,450 x 800 mm (without inlet and outlet tunnel) Condition: very good, ready for use
Cincinnati Titan92-APC Tapered Twin Screw Extruder Year of Make: 1996 incl. volumetric dosing unit for masterbatch Wittmann Dosimax Manual screen changer BD Plast Installed between extruder adapter and pelletizing head Alternatively available: Gneuss Screen Changer Granulating head Cincinnati GK120 works in the hot knock-off method including adapter and funnel Circular vibrating screen IFE US 400 x 1000 FV – LM445T Year of manufacture: 2018 for the separation of particles that are not bound in the granules with particle size < 1.8 mm Vertical granule cooler Knorr GK-600-PVC Year of manufacture: 2018 Cooling volume: approx. 190 litres Mounted on a walk-on steel platform incl. cyclone separator, complete supply and outlet pipes and blower Big-Bag Filling Station incl. material transport and material weighing SBB weighing technology Condition: fully functio ...
Single Screw Extruder CINCINNATI PROTON 60-30G Output capacity: up to 320 kg/h (HDPE) – 180 kg/h (PP) Screw diameter: 60 mm, L/D = 30 Grooved catchment zone Motor (DC drive): 100 kW Screw speed: max. 221 rpm Tool zones: 5 pieces. + 1 piece for adapter Melt pressure & temperature sensor included Control Cincinnati EXc Pro-NT Cylinder in bimetal design - Condition: good Auger web armored and hardened feed zone - Condition: good Dimensions (L x W x H): 2,580 x 1,430 x 1,800 mm Weight: 2,500 kg Condition: Good – machine was regularly serviced Various spare parts are included
GREINER double-strand calibration table getCAL 11.2-5P/4Z - DUAL A (2008) Clamping table (L / W / H): 2 x 11,170 / 2 x 380 / 940 – 1,040 mm Rail spacing: 2 x 320 mm Center Distance Dual: 500 mm Clamping width (max.): 400 mm Height adjustment: 100 mm Side adjustment: (+/-) 15 mm Longitudinal adjustment: 750 mm Tilt adjustment: (+/-) 10 mm 5 vacuum pumps á 4.6 kW incl. 50 ABA 1/2'' vacuum connections 4 cyclone pumps á 1.1 kW Dimensions (L x W x H): 11,200 x 1,580 x 1,200 mm incl. calibration & water tanks GREINER Double Strand Fume/Saw Combination getCOM 30/9-235-S/500 (YOC 2008) Max. profile dimensions (W x H): 235 x 140 (per side) Contact length tracks: 2 x 2,300 mm Number of cleats: 2 x 55 pcs. Lug width: 235 mm (per side) Pull-off force max.: 30 kN (per side) Pull-off speed: 0.5 - 10 m/min Extrusion height adjustable via machine feet: 1,040 – 1,140 mm Saw ...
CINCINNATI PROTON 45-30G Attention: Machine in left-hand version Screw diameter: 45 mm, L/D = 30 Grooved catchment zone Motor (DC drive): 65 kW Screw speed: max. 320 rpm Tool zones: 4+1 for adapters Melt pressure & temperature sensor included EXcPRO-NT control incl. CAN bus for data communication Air conditioner for control cabinet Cylinder in bimetal design – condition: very good Screw with few operating hours – condition: very good Without material funnel & without adapter
CDM PREALPINA 500-600 kg/h, Materials PE PP PC PS ABS PA, extruder with 130 mm. screw diam. 35L/D, a.c. 283 kw drive, Constructed in 2013, crammed feeding unit, extruder 130 mm., one degassing pump 5,5 kw, fully-automatic screen changer FIMIC RAS 400, water ring pelletizing unit, drying centrifuge, heat exchanging unit, vibrating screen, electric cabinet, machine offered reconditioned, installed power - used power in work: about 60-65% : 435, availability: Subject to unsold, conditions: Totally reconditioned, options available: Fimic or non stop screencganger + buffer silo or loading screw+hopper, used power in work: 280 kw, cooling: 13.400 Kcal/h, MATERIALS: PE PP PC PS ABS EPS XPS EPP, delivery time: 30 days ca
FIMIC RAS 325 SCRAPER, fully automatic screenchanger, screening surface 77.900 mm², Throughput: up to 600 kg/h depending on material and contamination, with scraping system, suitable for extrusion lines with capacity up to ca 500 kg/h or more depending on screening, Just disconnected, excellent conditions, constructed in 2017, immediately available, We can supply spare screens for this machine at competitive prices., Laser screen from 80 to 300 µ - Mesh from 180 to 50, Punched screen from 400 to 2.000 µ - Mesh from 40 to 10, availability: immediate, type: fully automatic
Innovac GmbH
