Manufacturer:
(Category: 302)
Varex 3-layer blowfilm-extruder Head diameter: 630 mm Screw diameter: 70-90-70 mm( die gap: 2,4) Film width: 1390 – 2580 mm Film thickness: 10-200 my Output: max 480 kg /hour Winding diameter 1200 mm Core diameter 76/150/152 mm Energy: 295 kW/h Treatment: in+outside
Material: PE, PP, PS, ABS // Details: DC motor, segmented screws and cylinders, screw speed max. 300 rpm, degassing, vacuum pump, mass pressure and mass temperature sensors, strand head, control cabinet for heating and motor control. Siemens Simatic OP17 controller Screw Ø: 2x 75 mm L/D: 36:1 Motor: 143 kW (DC)
Material: PE, PP, PS, ABS // Details: DC motor, segmented screws and cylinders, screw speed max. 300 rpm, degassing, vacuum pump, mass pressure and mass temperature sensors, strand head, control cabinet for heating and motor control. Screw Ø: 2x 67 mm L/D: 34:1 Motor: 97.5 kW (DC)
The extrusion line is a COEX cast film line. Processing of thermoplastics in a processing range of 150-300°C. Possible layer structures: - Monofilms - 3- layer (A-B+C-A) - 5- layer (A-B-C-B-A) Plant data: Total system output max. 2230 kg/h Extruder A: 90/33 L/D max. 330kg/h Extruder B.: 135/33 L/D max. 950kg/h Extruder C.: 135/33 L/D max. 950kg/h Film width NET: 1600 - 2110mm; Center cut for 2 bobsleighs possible (2x 800 – 2x 1055mm) Thickness: 25-580μm Production speed 10 - 150m/min Roll width 2500 mm roll weight 2000kg Additional components (quality): non-contact thickness gauge for automatic nozzle with automatic cross profile control on both sides Corona pretreatment (max. 12000W) Optical surface inspection system incl. defect marking in open and pass-through light Ancillary equipment: Dryer 1 – 4 with 4500 liters volume ; Heating capacity 48kw dryer 5 ...
The original part is a main and KO extruder from Kuhne built in 2006, the system was extended in 2010 by an additional extruder from the SML (coating unit). Plant description: COEX cast film line with additional coating unit. The main plant is equipped with a co- and a main extruder. The coating unit with a main extruder. Processing of thermoplastics in a processing range of 90-300°C. The system can be operated with the following combinations: • Main unit (CoEx system) with coating unit • Main unit (CoEx system) without coating unit • Only coating unit with unwinding unit for carrier film For operation in the various combinations, the corresponding additional units are switched on or off. Possible layer structures: Main plant: - Monofilm with release film if required - 3-layer film (A-B-A) with release film if required Coating: - Monofilm on carrier material if req ...
used
Extrusion recycling machine EREMA 1514T for processing of CLEAN unprinted polyethylene and polypropylene, WITHOUT DEGASSING, no converting of printed materials. capacity up to approx. 1.100 kg/hr. The machine is refurbiushed in ecellent condition. Auch Folien + Technik e. Kfm. D-73723 Esslingen phone +0049 1577 5329827
used
Used first-class renovated extrusion recycling plant EREMA for the processing of polyethylene and polypropylene. Capacity of approx. 1,100 kg/h. WITHOUT DEGASSING. Processing of only CLEAN material; without printing ink. Auch Folien + Technik e. Kfm. D-73728 Esslingen Phone +0049 1577 5329827
turning diameter over bed: 920 mmturning diameter over slide rest: 600 mmturning length: 12000 mmloading capacität: 20 tons turning speed range: 3,6 - 172 U/minvolt: 380 Vtotal power requirement: 90 kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Furnace 1200 temperature range 100 - 1200 Celsius inner dimensions 1x1x2m power 50kW PLC could be various size industrijskih peći INDUSTIJSKIH PECI NIKOTIRANJE CEMENTIRANJE TERMIČKA OBRADA ČELIKA KALJENJE INDUKCIONO PLAMENO ALATNIH I KONSTR. ČELIKA ŽARENJE MEKO NORMALIZACIONO STABILIZACIONO CNC obradni centri za struganje Završno precizno struganje Brušenje nakon termičke obrade, Zatvaranje tolerancija - lanci mjera, Kombinovani postupci struganja i glodanja, Dijelovi za automobilsku industriju i industriju mašina od čelika obojenih metalą CNC 3-osni obradni centri, Konvencionalno glodanje za pripremu i doradu, Kombinovano CNC struganje i glodanje, Zat varanje tolerancija - lanci mjera, PEĆI ZA TERMIČKU OBRADU ZAŠTITNE ATMOSFERE PEĆI ZA TERMIČKU OBRADU SA ZAŠTITBNOM ATMOSFEROM NITRIRANJE,CEMENTACIJA, POBOLJŠANJA, ŽARENJA, CARBONITRIRANJE NITROKARBURIRA ...
Screws: 2x x 58 mm / 26D Engine: 250 kW DC Capacity: approx. 800 - 1000 KG Material: PE, PP, PS, ABS // Details: DC motor, concurrent, segmented screws and cylinders (2x x 58 mm / 26D), screw speed: max. 900 rpm, degassing, vacuum pump, BKG underwater pelletizing system OPTI-LINE 1 consisting of: Kreyenborg start-up, water box, cutting head, water circulation system, heat exchanger, process water tank, centrifugal Control: Siemens S7 with visualization
According to description pdf attached complete line for profiles + WPC profiles
Compounder with segmented screw elements, cylinder with a degassing opening with hot tee, stainless steel housing, swivel
Extruding system with cross-spray head for sheathing of small profiles/filaments consisting of: 30 mm extruder with tool, water bath, extractor and winder Optional with memory for role change
1. Screen changer "Kreyenborg" K-SWE 180 2. Water ring granulation "AGRIFON" 3. Classification sieve for the separation of Granules over-good and lower grain sizes Throughput: Depending on material mix , 500 kg/h
Single-screw extruder • Type: 120/28 LD • AC Motor - 75 kw • Screw speed: 150 rpm. • Extruder cylinder: Air-cooled • Degassing zone Sieb changer • Strandhead Water bath: 4.5 m Granulator SG 200 Classic sieve Silo with conveyor fans: approx. 1m3
New laboratory extruder 25/25 LD Extruder Motor - AC Motor 2.2kW Water bath - 1000 mmm Granulator for a strand
Material: PE, PP, PS, ABS / Details: three-phase motor, DC, segmented screws and cylinders, degassing, vacuum pump, screw speed: max. 600 rpm, control: Resotec PLC
Designed for COEX- castfoil production with additional coating unit. The extrusion part of the line has 2 extruders; the coating unit has 1 extruder. Processing of thermo plastics in a temperature range of 90-300°C. Different combinations of production are possible: - main unit (CoEx) with coating - main extruder (CoEx) without coating - coating processing over winding unit on an existing base film For production in the different described combinations you can lock the not necessary equipment parts. POSSIBLE LAYER STRUCTURES: Main extruder: - Mono film if necessary with tensilized film - 3- layer film (A-B-A) if necessary with tensilized film Coating unit: - mono film on excisting base film if necessary with second tensilized film Unwind diameter: max. 1.000 mm Allowed roll/bobbin weight: max1.500kg MAIN EXTRUSION UNIT ...
The extrusion line was designed for cast film production. Processing of thermo plastics in a temperature range of 150-300°C. POSSIBLE LAYER STRUCTURES: - mono film - 3- layer (A-B+C-A) - 5- layer (A-B-C-B-A) DATA OF FACILITY Total output of extruders max. 2230 kg/h Extruder A: 90/33 L/D max. 330 kg/h Extruder B.: 135/33 L/D max. 950 kg/h Extruder C.: 135/33 L/D max. 950 kg/h Film width range (net): 1600 - 2110 mm Two rolls cutting possible (2x 800 – 2x 1055mm) Thickness range: 25-580μm Production speed: 10 - 150m/min Roll width: 2500 mm Max. roll weight: 2000kg ADDITIONAL COMPONENTS (QUALITY): Non-contact thickness equipment for automatic TD profile measurement with double side corona treatment (max. 12000W) Optical inspection system, including marker system if failures are detected, incident and transmitted light system ...
Compounding system with GALA underwater granulation Material: PE, PP, PS, ABS // Details: segmented screws and cylinders, screw diameter 2x 40 mm, L/D 44, DC rotor, DC motor 104 kW with gearbox, worm speed: max. 1,200 rpm, 2-fold degassing, ground pressure transducer, start-up valve, water box, Gala A1PAC6 underwater granulation with water circulation system and centrifugal dryer, temperature control unit SINGLE STW 150/1-6-100-NS/E, 6-fachimetric dosing incl. control. Control: Macromatex. Power: approx. 200 - 400 KG/hr
Material: PE, PP, PS, ABS / Details: three-phase motor 215 kW, segmented screws and cylinders, continuous rotors, screw diameter 50 mm, L/D 40, power: approx. 400 - 800 KG/hr, degassing, SIHI vacuum pump, gravimetric belt scale K-Tron WF 300 with stubble, strand nozzle, continuous cooling belt, cooling tank, squid granulator Scheer SGS 100, moisture measuring unit, control unit Siemens S7 with visualization.
Material: PE, PP, PS, ABS + talc, fibers / Details: twin-screw extruder PLAMA ZSP 70, segmented screws and cylinders, DC motor 260 kW, degassing, vacuum pump, side feed, low temperature control unit SINGLE, 4+1 gravimetric dosing BRABENDER incl. working platform, screen changer GNEUSS RSF 150, start-up crossover, underwater granulation GALA MAP6 with cutting rotor, water system, heat exchanger, centrifugal dryer. Controls: SIEMENS S7 with screen visualization SIEMENS Multi Panel 270B Touch. Power: approx. 600 - 800 KG/hr
Material: PE, PP, PS, ABS // Details: Screw diameter 2x 50 mm, L/D 32, DC motor 52 kW, Runner, segmented screws and cylinders, degassing, vacuum pump, screw speed: 400 rpm, strand nozzle, water bath, strand granulator. Power: approx. 150 - 250 KG/hr.
Material: PVC // with degassing, counter-rotor, DC motor 29 kW, screw diameter 86 mm, L/D 16 Capacity: 150 - 250 KG/hr
