Manufacturer:
(Category: 108)
length: 900 mmweight of the machine ca.: 95 kgdimensions of the machine ca.: 900 x 450 x 850 mmTechnical SpecificationsContinuously adjustable range [A] 35â250Duty cycle (DC) at Imax. (10 min) [%] 40Welding current at 100% duty cycle [A] 170Mains connection [V] 3/PE 400Continuous power at 100% duty cycle [kVA] 5.5Protection class IP 21Included: - Hose set- Pressure regulator- Ground cable- Spool adapterThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
current capacity: 25 kVAnumber of controlled axis: 6 workpiece weight: 10 kgweight of the machine ca.: 1550 kgYear of construction 2020 demonstration machine, as newEasy ARC 01.02 FD-B6 Welbee P500L welding robot stationMIG / MAG / water-cooled / torch RTW5000H / welding robot type FD-B6with welding table 2000x1200mmHole diameter 28 mmThe mobile welding cell for the craft businessSetting range MIG / MAG 20 - 500 ASteplessly adjustable switching levelsDuty cycle at max.current 40 ° C 50%Current at 100% ED 40 ° C 410 AWire feed speed 0 - 22 m / min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
DALEX PMS 10-4 & COHLINE Water Chiller DALEX, type PMS 10-4 powerful and robust industrial spot welding machine in a ready-to-use set with a matching COHLINE water cooling unit. Highlights & Condition: Extremely low mileage: The built-in DALEX MPS 100 digital control system shows an original odometer reading of only 13,282 cycles! For an industrial machine of this caliber, this is as good as new and guarantees minimal wear and tear. High electrode force: This model offers a powerful contact pressure of up to 690 daN for perfect spot welds even on thicker sheets. Including cooling: Thanks to the powerful COHLINE cooling unit (5.8 kW), the machine is immediately ready for permanent industrial shift operation without overheating. Flexibility & Safety: Equipped with a key switch for easy choice between control by footswitch or the two-hand safety console. Technical ...
wire electrode, welding wire, welding wire -Manufacturer: Elgar, started roll of MAG wire electrode -Type: Cromacore DW-309L O1.2mm -Dimension: O 300/100 mm -Weight roll: 10.1 kg
iDEAL BAS 065-11 is a resistance butt welding machine for band saw blades, made in Germany by IDEAL-Werk C.+E. Jungeblodt GmbH + Co., Lippstadt. Serial no. 235529, year of manufacture 2008. Rated power 20 kVA at 50% duty cycle, primary voltage 400 V, 50/60 Hz, secondary voltage 2.5 – 4.0 V, maximum upsetting force 50 kN. Hydraulic clamping (the "-11" version): both clamping jaws are operated hydraulically by foot switch, so the operator keeps both hands free to position the blade. The hydraulic power unit with clamping pressure gauge is mounted on the machine. Welding current is selected with the step switch, flashing speed and annealing time are set on the front control panel, with a Panasonic timer for the annealing cycle. A flexible work light is fitted above the welding zone. Capacity: bi-metal band saw blades 10 x 0.7 – 41 x 1.6 mm, wood band saw blades 10 x 0.7 – 60 x 1.0 mm, ...
Welding and annealing of bandsaw blades is the stated application of this iDEAL BAS 120, year of manufacture 1997. Wood band saw blades are covered from 25 mm upward to the 120 mm maximum blade width. Annealing control is by pyrometer. Clamping is hydraulic, described as providing constant and repeatable welding pressure for the joint. The power supply is 400 V at a frequency of 50-60 Hz. Weight is 800 [kg] and dimensions are 100013501700 [mm]. Documentation consists of the operating manual, schematics and spare parts list; the remaining figures are given in the specification table on this page. Band saw blades for wood 25-120 mm Bi-metal bandsaw 25-100 mm
Offer 26289 Technical data approx. : - CNC flame cutting machine with 2 burners as shown - 2 burner heights + tilt adjustable - Track gauge approx. 4.2 m - Track length approx. 7.5 m - Track height approx. 0.5 m - Space requirement approx. L 8 x W 7.5 x H 2.3 m - Weight approx. 3 T - Without support table
Manufacturer: CLOOS Model No.: Welding robot Year: 2017 Condition: Used Stock number: 9507
table diameter: 800 mmtable load: 1100 Kgswivelling range: 360 Gradturning speeds: U/minconnected load frequency: 400 Vweight: 3,5 tDimensions (LxWxH): 2,8 x 1,2 x 2,4 mWelding positioner- consisting of a column with RDM 50 slewing ring Typ RDM50- RDM 11 rotary table Typ RDM 11- System without control cabinetThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table diameter: 800 mmtable load: 1100 Kgswivelling range: 360 Gradturning speeds: U/minconnected load frequency: 400 Vweight: 3,5 tDimensions (LxWxH): 2,8 x 1,2 x 2,4 mWelding positioner- consisting of a column with RDM 50 slewing ring Typ RDM50- RDM 11 rotary table Typ RDM 11- System without control cabinetThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
A central welding fume extraction system is offered. Airflow: 30000m³/h, airflow: 30000m³/h, motor power: 30kW, compressed air connection: 6-8bar, max. static pressure: 2500Pa, duty cycle: 100%, control: PLC. The system is equipped with 2 spark traps and various ductwork components (extraction arms and hoods not included). An inspection is possible by arrangement.
An industrial welding robot is offered. Reach: 1450mm, payload: 5kg, operating hours: 2213h, welding power source: ESAB AristoMig 500W, max. welding current: 500A, duty cycle: 60% at 500A/100% at 400A, controller type: IRC, robot variant: 1600-5/1.45, controller: IRC. Equipment: ESAB AristoMig 500W welding power source, IRC control cabinet, linear axes/positioner tracks. Weight: approx. 500kg, overall dimensions X/Y/Z: approx. 1200mm/800mm/1600mm. An inspection is possible by arrangement.
Working range: 1250x2250mm, max. feed speed: 48m/min, welding range: M3-M8, welding diameter: 3-8mm, stud length: 8-40mm, max. welding capacity: 30-40studs/min, max. feed: 48m/min, positioning accuracy: +/-0.2mm, length: 2400mm, width: 2700mm, height: 3100mm, the machine has been used very little and is in good condition. An on-site inspection is possible.
Max. load capacity: 30t/set, min. workpiece diameter at 90°: 466mm, max. workpiece diameter at 30°: 11457mm, roller dimensions: 520mm×355mm, roller covering: rubber, max. speed: 1295mm/min, motor power: 2×1.5kW, weight drive unit/idler unit: 1300kg/700kg. Documentation available. An on-site inspection is possible.
Welding power source: Starmatic 1003 DC, max. welding current: 1000A at 100% duty cycle, lifting column height: 4850mm. Including flux tray, rail and vessel turning device. Documentation available. An on-site inspection is possible.
Laser source: Bystronic BLT 3500 Turbo, laser power: 3500W, wavelength: 10600nm, max. sheet weight: 160kg/m². Base machine weight: approx. 7000kg, laser source weight: approx. 1600kg. Documentation available. An on-site inspection is possible.
- set 1 (5 x in stock) Driven Master unit CD-30- set 1 (5 x in stock) Idler Slave unit CI-30 - Load capacity drive 15 ton- Load capacity idler 15 ton- Turning capacity combi 45 ton- turning speed 130 - 1300 mm/Min- Wheel size diameter 520 mm- Wheel size width 176 mm
- 1 x Driven Master unit 150 ton- 3 x Slave Idler unit 150 ton- Vessel diameter 1000 - 5000 mm- Wheel diameter:- Wheel width:- Rotation speed 10 - 1000 mm/Min
used
Manufacturer: Rudholzer Type of Machine: Welding machine Year of Manufacture: 2018 Materials Processed: PC + ABS/GF Product-Contact Parts Construction: Steel Key Technical Specifications: - Length 3, Width 3, Height 4 (cm or m) - Weight 4000 kg - Voltage 400 Volts - Current 83 Amperes - Power 57.6 (Kw or KVA) - Frequency 60 Hz - Phases 3 - Compressed air 7 (bar or psi) Find more here - .ucymachines/ Contact us at - sales@ucymachines
Manufacturer: KUKA Model: KR 5 ARC Year: 2014 Condition: Used Stock number: 9467 Control system: KUKA KR C4 Maximum arm reach: 1412 mm Number of axles: 6 pieces Maximum load capacity: 5 kg Machine weight: 127 kg The offer includes: Smart Pad Control Panel FRONIUS TransPuls Synergic 4000 water-cooled welding power unit Steel robot base Steel Fence Complete electrical installation
table length: 2400 mmtable width: 1200 mmtable height: 880 mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
table length: 3000 mmtable width: 1500 mmtable height (lateral area): 200 mmweight: 1549 kgdimensions of the machine ca.: 3000 x 1500 mm SIEGMUND Authorized Dealer - All Items in Stock! SPECIAL OFFER SIEGMUND Retro Welding Table 3000x1500x200, accessories includedSIEGMUND welding table just like 25 years agowith plasma nitriding and modern table legsProduct Description- Table dimensions: 3000x1500x200 mm- High-quality S355J2 N steel with plasma nitriding- Material thickness: approx. 24.5-27 mm- Hole diameter: 28 mm- Holes arranged in a 100x100 mm grid- Corners, edges, and holes chamfered at 45°- Side panel height: 200 mm- Holes in side panels arranged in a diagonal grid- Construction reinforced with ribsPlasma-nitrided version:- Protection against rust, scratches, and weld spatter adhesion- Corrosion-resistant / higher load-bearing capacitySpecifications:- 28-hole pattern / Dimension ...
Manufacturer and model: iDEAL BAS 050-11 Rated power (ED 50%): 4.5 kVA Secondary voltage: 2.6 – 4.4 V (6 stages) Clamping force: 10 kN (hydraulic) Maximum compression force: 2.2 kN Iisc Hq E Rrszqdkxjvef Machine weight: approx. 180 kg Hydraulic tensioning, operated via foot switch Pyrometer (GTR): yes (temperature display on the touch panel) Connection voltage: 380 – 419 V Bi-metal/carbide saw blades: 6×0.6 – 34×1.1 mm Wood saw blades: 6×0.4 – 50×1.0 mm Stainless steel saw blades: 6×0.4 – 25×0.5 mm Blade dimensions: 6×0.4 – 30×0.6 mm Blade steel S235JR: max. cross-section 75 mm² Blade steel X5CrNi18-10: max. cross-section 40 mm² Pyrometer / GTR: The integrated pyrometer (GTR) enables contactless temperature measurement during the annealing process. The target temperature is pre-defined in a recipe and displayed on the panel – the annealing cycle en ...
An MBK horizontal cage welding machine for the production of small square reinforcement cages is offered. Cage diameter: approx. 200mm-1500mm, max. cage length: 4000mm, wire diameter: 5mm-12mm, welding capacity: approx. 100kVA, control: Zoller+Fröhlich. Machine dimensions: approx. 6000mm/2500mm/2200mm, weight: approx. 8500kg. Inspection possible by arrangement.
Welding rectifier, standard: EN 60974-1, VDE: VDE 0544, mains connection: 3~/400V/50Hz, fuse protection: T25A, open-circuit voltage: 76V, max. welding current: 400A, protection class: IP23, insulation class: F, cooling method: AF-forced air cooling, weight: 214kg. An on-site inspection is possible.
Working area X/Y: 1500mm/3000mm, plasma source: NERTAJET HP120, control: DIGISAF 100, max. cutting capacity steel/stainless steel/aluminum: 20mm/15mm/20mm, wet and dry cutting possible, extraction system available. Documentation available. Inspection possible by arrangement.
Welding fume filters, welding fume extraction systems, soldering fume extraction systems, mobile filter units, dust collectors, welding fume extractors -Manufacturer: Donaldson Torit, mobile welding fume extraction / dust collector type PT 1000 -Drive: 1.1 kW -Max. volume flow: 1100 m³/h -Extraction arm: Ø 165 mm x 2210 mm -Transport dimensions: 1200/620/H1645 mm -Weight: 105 kg
Welding fume filters, welding fume extraction systems, soldering fume extraction systems, mobile filter units, welding fume extractors -Welding fume extraction: welding fume extraction arm -Extraction arm: Ø 200 mm x 4700 mm -Transport dimensions: 2490/800/H290 mm -Weight: 31 kg
