manual used for sale

Window drip cap roll forming machine PO-1 Window drip cap roll forming machine PO-1 allows to produce window trim” profile by rolling the sheet metal through forming rolls. A window trim is an element that is widely used in construction while windows installation. In the standard way the window trim is bent step by step using a manual folding machine. This is a cheaper, but more time-consuming process. The metal sheet must be pre-marked for each bending operation. Each bend is then performed using a manual bending machine. The operator must set the necessary dimensions according to the marks, fix the sheet metal with the machine's fixation mechanism, and then bend it. The length of the window trim is limited to the maximum working length of the bending machine. Thus, each manual folding operation is time-consuming and the production process becomes expensive and inefficient. To im ...

Pass-through width mm: 150 Pass-through height mm: 40-120 Workpiece length min mm: 450 Configuration: Position 1 - Vertical swivel brush unit L (Manual) Position 2 - Vertical swivel brush unit R (Manual) Position 3 - Lower grinding plates (motorized) Position 4 - Lower grinding plates (motorized) Position 5 - Lower grinding plates (motorized) Position 6 - Lower Horizontal Brush Unit (Manual) Total connection KW: 15 Weight Kg: 2000 With roller conveyor and conveyor belt

WSM Stationary screwdriving unit screwdriving station Assembly of parts for car radios and navigation systems and for testing them. The assembly station is surrounded by a protective enclosure. The service doors are equipped with interlocking monitoring switches. The doors are locked in automatic mode and can only be opened when the automazik stop or in manual mode after pressing the doors on the control panel. When the door is open, automatic operation cannot be started. Functional sequence The station is equipped with the pre-assembled assembly via the transfer belt. The work steps of the automatic station with a run of a WT are described below. In normal operation, all 3 stations work in parallel. - Positioning the WT with the pre-assembled assembly in St.2.1 - Lowering the wearer with the scanner and the vision sensor - Scanning of the 3 codes (front panel, fro ...

We offer here a contour measuring device from MITUTOYO, this device received maintenance and calibration from Mitutoyo in November 2022. Included is the complete control with PC, monitor and software Formtracepak MITUTOYO Contour Measuring Machine SV-3000 CNC ROUGHNESS TESTER MITUTOYO Contracer Extrem-SV-3000 CNC SURFTEST SV-3000 CNC 178-544-2 TECHNICAL DATA Range X-Axis: 8" / 200mm Resolution X-Axis: 1.97μin / .05μm Measuring Method: RT Linear encoder X-axis Drive speed (max. CNC): 7.87in/s / 200mm/s X-axis Drive speed (manual joystick): 0 - 2.0in/s / 0 - 50mm/s Measuring Speed: .00078 - .078 in/s / .02 - 2 mm/s Traversing Direction: Backward Alpha-axis resolution: .000225° Alpha-axis rotating speed: 1rpm Column resolution: 1.97μin Column Resolution: 0.05μm Z2-axis Measuring Method: RT Linear encoder Cjycziziin Column Z2-axis drive speed (max. CNC): 7.87in/s ...

We offer here a contour measuring device from MITUTOYO, this device received maintenance and calibration from Mitutoyo in November 2022. Included is the complete control with PC, monitor and software MITUTOYO Contour Measuring Machine SV-3000 CNC ROUGHNESS TESTER MITUTOYO Contracer Extrem-SV-3000 CNC SURFTEST SV-3000 CNC 178-544-2 TECHNICAL DATA Range X-Axis: 8" / 200mm Resolution X-Axis: 1.97μin / .05μm Measuring Method: RT Linear encoder X-axis Drive speed (max. CNC): 7.87in/s / 200mm/s Cjycziziin X-axis Drive speed (manual joystick): 0 - 2.0in/s / 0 - 50mm/s Measuring Speed: .00078 - .078 in/s / .02 - 2 mm/s Traversing Direction: Backward Alpha-axis resolution: .000225° Alpha-axis rotating speed: 1rpm Column resolution: 1.97μin Column Resolution: 0.05μm Z2-axis Measuring Method: RT Linear encoder Column Z2-axis drive speed (max. CNC): 7.87in/s / 200mm/s Z ...

max. grinding diameter: 320 mm grinding length: 500 mm workpiece length: 700 mm total power requirement: 10 kW weight of the machine ca.: 4 t dimensions of the machine ca.: m Height of centres 220 mm Distance between centres / clamping length 750 / 500 mm Table size 290 x 1,600 mm Intermediate table 110 x 1,200 mm X / Y / Z axes 500 / 320 / 320 mm Feed speeds, X, Y & Z axes 0.005 - 5 m/min Grinding head swivelling, vertical axis, manual 200 ° Grinding head tilting, manual +/- 90 ° Speed range of R axis, approx. 0 - 50 rpm Grinding spindle speeds, infinitely variable, approx. 2,000 - 12,000 rpm Workpiece holding fixture 50 ISO Indexing 1 - 999 ° Leads 0.5 - 10,000 mm Spindle drive 4 kW Total electrical load, approx. 10 kW - 380 V - 50 Hz Weight, approx. 4,000 kg Accessories / Special Features SCHÜTTE CNC Continuous Path Control for 4 axes with SIEMENS/BOSCH components and SIEMENS  ...

table diameter: 400 mm workpiece weight: 315 kg table height: 360 mm max. height (90° position): 635 mm height of the swivelling axis: 240 mm distance table center - swivel center: 485 mm center bore: 40 mm rotation movement: 360 ° reading accuracy of turning index: +/-4 ° swivel movement: 90 ° power capacity: kW weight of the machine ca.: 0,31 t dimensions: 850x450x360 mm • new-valued, manual operated, swivelling rotary indexing table, • H4 = indicating system for circular movements 0 - 360 ø +/- 4 above optic, • S20 = indicating system for swivelling movements 0 - 90 ø +/- 20 above scale ring, • B = manual operation for 0 - 360 ø, • B = manual operation for 0 - 90 ø, The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

CNC lathe BOLEY type BE 42 - Bi-spindle / twin-turret TECHNICAL SPECIFICATIONS: CN Type: MITSUBISHI Meldas 635LCC X1 axis stroke: 170 [mm] Z1 axis stroke: 200 [mm] X2 axis stroke: 110 [mm] Z2 axis stroke: 395 [mm] X3 axis stroke: 110 [mm] Z3 axis stroke: 170 [mm] Y-axis stroke: -/+ 40 [mm] Tool holder type: VDI 20 Spindle for clamping clamps: Size 48 DIN 6343 Spindle passage diameter: 42 [mm] Mini speed. Pin: 80 [rpm] Maximum speed. Pin: 8000 [rpm] C-axis indexing accuracy: 0.001 [°] Pin power: 7.5 [kW] Counter-spindle passage diameter: 42 [mm] Mini speed. Counter spindle: 60 [rpm] Maximum speed. Counter spindle: 6000 [rpm] C-axis indexing accuracy counter-spindle: 0.001 [°] Counter spindle power: 2.2 [kW] Maximum diameter. Machinable: 140 [mm] Number of positions - Upper turret: 12 Number of motorized positions - Upper turret: 12 Maximum speed. rotating to ...

Pre-milling unit: yes; Pre-milling unit material removal: 0 - 2 mm; Plastic edges: 0.4 - 3 mm; Workpiece thickness: 8 - 50 mm; Workpiece length min.: 130 mm; Workpiece width min.: 80 mm; Glue unit: granules / glue container quick change kit; Chopping knife: yes; Flush cross-cut unit: yes; Corner copying unit: yes; Flush radius milling unit: yes; Radius Scraper Aggregate: yes; Surface scraper unit: yes; Buffing unit: yes; Power consumption: 9 kW; Machine Length: Machine Width: Machine height: Weight: Prima 7.3 r.a. PLUS â€" Partnership Edition Aggregates: Joining milling unit incl. AIGNER Diamant jointing cutter heads, with DIA interchangeable knife system Konstantin and controlled edge blow-out nozzle behind the 2nd joining cutter head. Cross-cut saw unit with suction device incl. pneumatically swivelling saw blades, adjustable and programmable from the control pa ...

sheet width: 1550 mm plate thickness: 2,0 mm roll length: 1550 mm roll diam. toproll: 90,0 mm engine output: manuell kW weight: 560 kg range L-W-H: 2580 x 700 x 1250 mm Furnishing: - manual asymmetrical 3-roll round bending machine with hand drive - manual folding warehouse - manual delivery d. rear roller - Profile grooves: 4/6/9 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 250 mm capacity 90 degrees: flat: 280 x 220 mm capacity 90 degrees: square: 220 x 220 mm capacity 45 degrees: round: 230 mm capacity 45 degrees: flat: 220 x 200 mm capacity 45 degrees: square: 200 x 200 mm capacity 60 degrees: flat: 140 x 100 mm capacity 60 degrees: square: 100 x 100 mm capacity 60 degrees: round: 110 mm vice: 285 mm turning speed range:: 36/72 m/min saw band length: 2.950 x 27 x 0,9 mm total power requirement: 1,5/1,8 kW weight of the machine ca.: 440 kg. dimensions of the machine ca.: 1620 x 1360 mtr. Furnishing: - manual band saw machine + with both. Miter device right 45 ° / left 60 ° - adjustable via large turntable - Selector switch for switching between manual and controlled lowering - autom. Limit switch-off - either manual or autom. Lowering the saw bow - Required instructions - saw band - coolant device - Angle stop - Chip removal brush - Op ...

pressure: 80 t chamfer lenght: 2600 mm distance between columns: 2200 mm column arm: 250 mm ram stroke speed: 90 mm/sec return speed: 7,5 mm/sec work speed: 60 mm/min work stroke: 160 mm dayligth: 380 mm oil volume: 150 ltr. table height: 900 mm voltage: 400 Volt weight: 5.227 kg range L-W-H: 3750x1950x2400 mm Furnishing: - DELEM - CNC control model DA-53T - controlled axes: Y1 - Y2 and X - AKAS laser in front of the machine - manual crowning - Upper tool, deer foot - Lower tool, die block with 4Vs - SICK light barrier behind the machine - 2 front support arms - SIEMENS - electrical system - BOSCH / HOERBIGER hydraulic system - CE mark / declaration of conformity - Operating manual: machine and control - Safety manual: press brakes The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 300 mm capacity 90 degrees: flat: 330 x 260 mm capacity 90 degrees: square: 260 x 260 mm capacity 45 degrees: round: 260 mm capacity 45 degrees: flat: 270 x 200 mm capacity 60 degrees: round: 180 mm capacity 60 degrees: flat: 170 x 170 mm height of material-table: 600 mm Pitch min/max: 50.000 mm vice: 335 mm Öffnung band speed: 15 - 100 m/min automatic feeds: 600 mm dimensions of saw-band: 3.650 x 27 x 0,9 mm total power requirement: 2,2 kW weight: 1.105 kg range L-W-H: 3,3 x 2,83 x 2,23 m Electro-hydraulic fully automatic band saw, with additional: semi-automatic semi-automatic dynamic manual operation Description : - Automatic cycle (cuts from 0 ° to 60 ° left) - Semi-automatic, semi-automatic-dynamic and manual cycle - Cuts from 45 ° right to 60 ° left - Manual or semi-automatic dynamic cycle - to make cuts without programming - Numerically controlled band sa ...

GeneralHorizontal machining center; Control: Control M730BM CharacteristicsSpeed max.15000 rpmDimensions (L x W x H)2,72 x 4,22 x 2,52 mSpindle taperBT 40 Tool Magazine with40 PositionsRapid feed X / Y / Z60/6060 m/minMovement X / Y / Z560/560/660 mmPalett changer with2 PalletMaximum load (table centre)400 KgSwivelling range360 x 0,001 degreeTable size400x400 mmDrive power (100% DC)18,5 kWWeight approx.7600 Kg(For Europe) European Edition(For Europe) European Edition (NHC4000) Full 4th axis rotary table Interface for Through-spindle coolant system (7.0 MPa, Variable Pressure Steps) (KNOLL) Coolant gun for setup station side In-machine measuring system (spindle) optical signalInterface for Through-spindle Coolant System (7.0 MPa, Variable Pressure Steps) (KNOLL/ Interlit)Interface for Through-spindle Coolant System (7.0 MPa, Variable Pressure Steps) (KNOLL/ Interlit) Interface for mountin ...

GeneralHorizontal machining center; Control: Control M730BM CharacteristicsSpeed max.15000 rpmDimensions (L x W x H)2,72 x 4,22 x 2,52 mSpindle taperBT 40 Tool Magazine with40 PositionsRapid feed X / Y / Z60/6060 m/minPalett changer with2 PalletMovement X / Y / Z560/560/660 mmMaximum load (table centre)400 KgSwivelling range360 x 0,001 degreeTable size400x400 mmDrive power (100% DC)18,5 kWWeight approx.7600 Kg(For Europe) European Edition(For Europe) European Edition (NHC4000) Full 4th axis rotary table Interface for Through-spindle coolant system (7.0 MPa, Variable Pressure Steps) (KNOLL) Coolant gun for setup station side In-machine measuring system (spindle) optical signalInterface for Through-spindle Coolant System (7.0 MPa, Variable Pressure Steps) (KNOLL/ Interlit)Interface for Through-spindle Coolant System (7.0 MPa, Variable Pressure Steps) (KNOLL/ Interlit) Interface for mountin ...

GeneralHorizontal machining center; Control: Control M730BM CharacteristicsSpeed max.15000 rpmDimensions (L x W x H)3,1 x 4,86 x 2,84 mSpindle taperBT 40 Tool Magazine with40 PositionsRapid feed X / Y / Z60/6060 m/minMovement X / Y / Z730/730/880 mmPalett changer with2 PalletMaximum load (table centre)500 KgSwivelling range360 x 0,001 degreeTable size500x500 mmDrive power (100% DC)18,5 kWWeight approx.11100 Kg(For Europe) European(For Europe) European Edition (NHC5000) Full 4th axis rotary table Interface for Through-spindle coolant system (7.0 MPa, Variable Pressure Steps) (KNOLL) Coolant gun for setup station side In-machine measuring system (spindle) optical signal transmissioInterface for Through-spindle Coolant System (7.0 MPa, Variable Pressure Steps) (KNOLL/ Interlit)Interface for Through-spindle Coolant System (7.0 MPa, Variable Pressure Steps) (KNOLL/ Interlit) Interface for mou ...

GeneralTurning-milling centre; Control: Fanuc 31iB5 CharacteristicsSwing- Ø, max.1070 mmDrive power milling spindle22 kWDrive power second spindle22 kWDrive power main spindle22 kWNumber of Toolmagazine positions50 Speed max.8000 rpmSlewability of B-Axis1 degreeMovements X / Z / Y1040/+-330/3150 mmMilling spindle upper side1 Input precision of C-axis on Counterspindle0,0001 degreeBar diametre164 mmSpindle speed 2nd Spindle max.1500 rpmInput precision of C-axis on Mainspindle0,0001 degreeBar diametre164 mmSpeed max.1500 rpmMax. Turning Length3076 mmMax machining diameter1070 mmWeight approx.46000 KgTool spindle full indexing specificationsErhöhung der mögl. Indexierung der B-Achse auf 0,0001º Einrichtung zur Positionierung der B-Achse mit einem minimalen Winkel von 0,0001º anstelle der Standardausführung mit 1º, einschließlich der Option Direktes Wegmesssystem in der B-Achse derSp ...

cutting diameter: 250 mm capacity 90 degrees: flat: 280 x 220 mm capacity 90 degrees: square: 220 x 220 mm capacity 45 degrees: round: 230 mm capacity 45 degrees: flat: 220 x 200 mm capacity 45 degrees: square: 200 x 200 mm capacity 60 degrees: flat: 140 x 100 mm capacity 60 degrees: square: 100 x 100 mm capacity 60 degrees: round: 110 mm vice: 285 mm turning speed range:: 36/72 m/min saw band length: 2.950 x 27 x 0,9 mm total power requirement: 1,5/1,8 kW weight of the machine ca.: 440 kg. dimensions of the machine ca.: 1620 x 1360 mtr. Furnishing: - manual band saw machine + with both. Miter device right 45 ° / left 60 ° - adjustable via large turntable - Selector switch for switching between manual and controlled lowering - autom. Limit switch-off - either manual or autom. Lowering the saw bow - Required instructions - saw band - coolant device - Angle stop - Chip removal brush - Op ...

laboratory autoclave Capacity: 75 litres. Steam sterilization: temperature 115 to 134º C; pressure 1.2 to 2 bar; time from 1 to 60 min. Triple safety system (safety thermostat, manual devaporization valve and overpressure safety valve). Built in stainless steel. Manual closing. Four wheels for transport. 220 V single phase; 3300W Operation manual available

Specifications 1.3.1 Dimensions, space requirements, weight, energy requirements Dimensions, weight Machine incl. control cabinet Length x Width (depth) x Height (incl. Levelling elements): approx. 3,600 mm x approx. 2,400 mm x approx. 2,500 mm Minimum height requirement: 3,500 mm Net weight: approx. 8,500 kg Pay attention to the set-up plan! It contains all connection data, space conditions, etc. necessary for energy supply and installation. 1.3.2 Spray-suppression cabin, full-space cover of the machine View into the machine interior: safety window (window composite) Design: polycarbonate lens protected on both sides Cover of mounting or maintenance openings: Sliding door(s) hinged and/or removable body parts Cover of the operators side, loading and unloading opening: sliding door, loading hatch Activity: - Foldable body parts,sliding doors of assembly and maintenance openings: manual - ...

GeneralTwo spindle turning centre with - partial hollow clamping device for main spindle and counter spindle internal diameter of draw tube Ø67 mm (2.63 in) x 700 mm (27.55 in) deep - 2 C-axes and spindle brakes (hydr.) - 2 12 fold Sauter star turrets reception VDI 40, DIN 69880-40 with precision interface (Trifix) and tool drive connection/drive acc. DIN 5480 - Y-axis, slide I - Counter spindle slide with NC-cross stroke and tailstock; Control: CELOS with Siemens 840D sl Operate Headstock, leftClamping chuck Ø315 mmSpindle nose diameter170h5 mmSpindle diametre on front bearing130 mmSpindle bore87 mmDrive power (100% DC)25 kWTorque (100% DC)280 NmC-Axis Speed2000 rpmSpeed range0-5000 rpmHeadstock, rightClamping chuck Ø315 mmSpindle bore87 mmSpindle nose diameter170h5 mmSpindle diametre on front bearing130 mmDrive power (100% DC)25 kWC-Axis Speed2000 rpmTorque (100% DC)280 NmS ...

cutting diameter: 300 mm capacity 90 degrees: flat: 330 x 260 mm capacity 90 degrees: square: 260 x 260 mm capacity 45 degrees: round: 260 mm capacity 45 degrees: flat: 270 x 200 mm capacity 60 degrees: round: 180 mm capacity 60 degrees: flat: 170 x 170 mm height of material-table: 600 mm Pitch min/max: 50.000 mm vice: 335 mm Öffnung band speed: 15 - 100 m/min automatic feeds: 600 mm dimensions of saw-band: 3650 x 27 x 0,9 mm total power requirement: 2,2 kW weight: 1.105 kg range L-W-H: 3,3 x 2,83 x 2,23 m Electro-hydraulic fully automatic band saw, with additional: semi-automatic semi-automatic dynamic manual operation Description : - Automatic cycle (cuts from 0 ° to 60 ° left) - Semi-automatic, semi-automatic-dynamic and manual cycle - Cuts from 45 ° right to 60 ° left - Manual or semi-automatic dynamic cycle - to make cuts without programming - Numerically controlled band saw ...

ARO Reversible Ergoline Type X Resistance Welding System Manual welding station For manual welding applications where safety, ergonomics and reliability come first, ARO models are the right choice for you. Advantages of manual welding - high performance - Cost efficiency - highest reliability. - recognized by the automotive industry Scope of delivery: Resistance welding gun incl. IQR Harvys reversible control unit

ARO Reversible Ergoline Type C Resistance Welding System Manual welding station For manual welding applications where safety, ergonomics and reliability come first, ARO models are the right choice for you.Advantages of manual welding - high performance - Cost efficiency - highest reliability. - recognized by the automotive industry Scope of delivery: Resistance welding gun incl. IQR Harvys reversible control unit

Iberdrill Gear Column Drill Series T, TL25 drilling capacity for steel (ST 60) at continuous power S1: D25mm drilling capacity for grey cast iron (GG 20) with continuous power S1: D30mm thread cutting capacity for steel (ST 60) with continuous power S1: M 18 thread cutting capacity for grey cast iron (GG 20) with continuous power S1: M 22 Tool holder in the spindle: MK 3 spindle stroke (drilling depth): 120 mm Motor power spindle: 0.82/1.2 kW Drive: 8-speed gearbox with pole-shiftable motor Speed adjustment: manual Speed range for 50 Hz motor, n=1,500/3,000 rpm, pole switchable 65 -125 -185 - 365 - 540 - 1,055 - 1,560 - 3,060 rpm Feed: 300 mm x 270 mm Column diameter: 100 mm Distance spindle center / column (projection) 250 mm Machine weight (net) 250kg Gross weight 310kg Dimensions transport packaging (LxWxH) 2.14m x 0.6m x 0.8m Gearbox ...

Wirotech tube mill 32x2mm Make: Wirotech Year: 2011 Production material: Hot rolled steel, Cold rolled steel, Pickled steel, Galvanized steel – Min./Max. ø tube: 14 – 32 mm. – Min./Max. Thickness: 0,7/ 2,0 mm. – Min./Max. width tape: 43 / 101 mm. – Max. speed of line: 60 meters per minute Pipes that can be produced: – Tubes (mm): 14; 16; 18; 20; 22; 25; 26,9; 28; 32 – Square (mm): 15×15; 16×16; 18×18; 20×20; 25×25 – Rectangle (mm): 20×10; 25×15; 30×10; 30×15; 30×18; 30×20; – Other (mm): eliptic 44×18; eliptic 30×20; semioval 30×15 Line components: 1. Double strip uncoiler Width: 1650 mm Length: 1100 mm Height: 1900 mm Capacity: 2 x 2000 kg Maximum outer diameter of the strip: 1580 mm Manual brake for steel strip rotation Min/max mandrel expansion: 470/540 mm 2. Strip end welder Producer: Kent Hydraulic cutting guilloti ...

cutting diameter: 300 mm saw band length: 3650 mm cutting width: 330 mm : 40 / 80 m/min : 3650 x 27 x 0,9 mm : 300 mm : 260 mm : 330 x 260 mm : 260 mm : 250 mm : 270 x 200 mm : 180 mm : 170 mm : 170 x 170 mm : 870 mm : 2,35 kW : 0,7 t : 2,7 x 1,6 x 2,0 m Powerful miter band saw for cuts from 45 ° right to 60 ° Left Electro-hydraulic semi-automatic machine with microprocessor control New version: now with anti-vibration rollers and an even more powerful gear size 75 and considerably reinforced cast steel saw frame Control modes: Manual mode Semi-automatic dynamic operation (The semi-automatic cut is made by manual approach of the saw bow from any position via actuation of the handset started) Semi-automatic operation (start / stop position of the saw bow is controlled by the Keyboard programmed Vice closes / opens automatically, the saw curve becomes the start of the cut automatically  ...

TRIBLOCK GAI: Year 1995 Clockwise direction 1) Rinser 12 clamps, single treatment with air breath Manual height adjustment 2) Vacuum station with nitrogen before filler 3) Filler 16 valves with light vacuum in the tank Manual adjustment of the tank height 4) Capper single head for natural straight corks with vacuum before capper Manual height adjustment Safety protections

JOTES SOH-10 internal grinding machine was built in Poland. The SOH10 grinding machine is used in the finishing process to give the right shape and surface roughness to holes with a diameter from 10 to 100 mm and conical holes with a maximum apex angle of 30°. The high-performance spindle machines workpieces with a maximum diameter of 300 mm (with guard) or 450 mm (without guard). The total weight of the machine is 2900 kg. Technical parameters of the JOTES SOH-10 internal grinding machine - minimum hole diameter: 10 mm - maximum hole diameter: 100 mm - maximum hole length: 160 mm - maximum diameter of grinded workpiece (with guard): 300 mm - maximum diameter of grinded workpiece (without guard): 450 mm - spindle rotation speed: 70-700 rpm - manual spindle feed (1 wheel revolution): 2,5 mm - largest spindle turning angle: 15° - lateral manual feed of spindle (forward): 50 m ...

Number of motors: 2 Stück 0: 2650 mm Control: , 0 Ruchser RU-GLS-ED 45° glass bead saw -------------------------------------- Developed for cutting glazing beads in pairs The RU-GLS-ED45° double glazing bead saw must be adjusted to size manually. the Machine was designed for cutting glazing beads in pairs with a cutting angle of 45° and features a fixed and a movable saw unit. The manual length adjustment is equipped with an electrical digital display. It can cut lengths from 240mm - 2650mm be sawn. During the cutting process, the glazing beads with a pneumatic clamping device clamped from above and from the front to prevent tilting to prevent the glazing beads. Operation is via a safety two-hand operation Item 1: RU-GLS-ED45° double glazing bead saw ----------------------------------------------------- with manual measurement, for the pairwise Cutting glazing beads, cutting angle  ...

CNC vertical machining center HERMLE C 42 V With path control Heidenhain iTNC 530 Year of construction: 2016 Travel : X 800 Y 800 Z 550 Speed range: 20 – 42,000 rpm continuously variable (HSK 40) With the following accessories: Rigid angle table 1050 mm x 805 mm clamping surface Vertical tool changer with 42 magazine slots ( HSK 40) Linear axis dynamics , remote maintenance Blow-off device Coolant equipment , Chip tray Manual cabin door , Manual cabin roof Polycarbonate safety glazing Electronic heat compensation iTNC 530 Electr. Manual operating module HR 410 BLUM Laser A1 rigid table , mod. BLUM A1 with optics BL 104 3 D touch probe Heidenhain Control cabinet cooling unit ( RITTAL) Status light 7-fold media connection rigid table 4 pieces of height-adjustable machine shoes Operating instructions THE MACHINE ONLY MILLED BRASS PARTS Absolutely MINT C ...

sliding carriage length: 2800 mm; cutting width with rip fence: 1350 mm; cutting width at the cross cut: 2800 mm; cutting height: scoring unit: yes; height adjustment: manual / crank; tilt adjustment: manual / crank; rip fence adjustment: manual; display saw blade tilt: digital; display saw blade height: -; display rip fence: scala; display at the cross cut: scala; saw blade diameter: 315 mm; speeds: 1; motor power: 4 kW; motor brake: yes - automatically; suction connection: 80 mm und 120 mm; machine length: 3000 mm; machine width: 2100 mm; weight: ca. 1000kg;

Pressing area: 3000 mm x 1800 mm; Number of manual hydraulic cylinders vertical: 3; Number of manual hydraulic cylinders horizontal: 2; Pressing pressure: 1500 kg; Machine length: 4000 mm; Machine width: 750 mm; Machine height: 2250 mm; Chassis on wheels, two of which steered Manual hydraulic cylinders height adjustable Vertical sliding posts

Carriage length: 3800 mm; Cutting width at width fence: 1000 mm; Cutting width at cut-to-length fence: 2800 mm; Cutting depth: Scorer: no; Height adjustment of saw blade: manual / hydraulic; Swivel adjustment saw blade: manual/hydraulic; Adjustment of width stop: manual; Display Saw Blade Angle: Scala; Display cutting height: -; Display Width Stop: Scala; Display Cut-to-length ruler: Scala; Saw blade diameter: RPMs: 4; Motor power: 5.5 kW; Engine brake: yes; Suction connection: 80 mm and 120 mm; Machine length: 3870 mm; Machine width: 1700 mm; Weight:

sheet width - max.: 1255 mm plate thickness: 4,0 mm ST plate thickness: 2,0 mm VA plate thickness: 6,0 mm ALU number of strokes - loaded: ~ 66 Hübe/min. cutting angle: 1,5 ° total power requirement: 5,5 kW weight of the machine ca.: 2600 kg. range L-W-H: 2300 x 1800 x 1800 mm Machine from a technical college - prototype construction very well-maintained condition () Furnishing: - electro-hydraulic guillotine shears - manual backgauge with analogue position display (scale + magnifying glass) - electrical cutting length limitation - manual cutting gap adjustment - 1x extra long side stop - 2x extra long support arms - 1x free moving footswitch - rear sheet metal slide - User manual (PDF) Machine link : http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=1008 -9325278 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cutting diameter: 300 mm capacity 90 degrees: flat: 330 x 260 mm capacity 90 degrees: square: 260 x 260 mm capacity 45 degrees: flat: 270 x 200 mm capacity 45 degrees: round: 250 mm capacity 45 degrees: square: 250 x 250 mm capacity 60 degrees: flat: 170 x 170 mm capacity 60 degrees: square: 170 x 170 mm capacity 60 degrees: round: 180 mm turning speed range:: 40 / 80 m/min saw band length: 3650 x 27 x 0,9 mm weight of the machine ca.: 640 kg New price ~ 11.500 euros Furnishing: - automatic lowering of the saw arch, with steplessly adjustable feed - with limit stop at the end of the cut - manual / semi-semi-automatic function selectable - 2x saw band speeds - large bearing turntable, for miter cuts from 45° right - 60° left - Vice manually adjustable on both sides - manual material clamping - 1x saw band - rotating chip removal brush - Control panel - front right - hydraulic pressure  ...

GF Mikron E 500 U 5-Axis CNC Vertical Machining Center Year: 2018 SPECIFICATIONS: X-AXIS 19.69" Y-AXIS 17.72" Z-AXIS 15.75" # AXIS 5 SPINDLE SPEED 12,000 RPM ATC CAPACITY 30 TAPER BT 40 EQUIPPED WITH: 1k cutting hours Heidenhain iTNC 530 CNC Control Renishaw TS-27R Probe Touch Probe Infrared OMP40 Assortment of Tooling Tool Magazine DT40/BT40 & ISO4 TC Arm Holder For ISO 40 Kinematicsopt (2) Compressed Air Through Spindle Compressed Ball 30 with Base Hem Rotary Tilting Table Hem Linear Glass Scales 500U Conveyor Lift Up Chip Movable Hand Wheel Manual Touch Cycles Heidenhain Manual Pilot Smart NC Heidenhain Manual DIN/ISO Programming Heidenhain

sheet width: 1050 mm plate thickness: 8,0 mm distance between columns: 1250 mm angle adjustable from - to: 0 - 180 Grad upper clamping bar adjustment: 350 mm traversing speed: OW 4,4 mm/sek Control: ELGO TYP 86 back stop - adjustable: max. 1000 mm engine output: 5,5 kW weight of the machine ca.: 3200 kg range L-W-H: 1900 x 2600 x 1600 mm maintained condition with a lot of bending tools () Pointed rails, radius rails, bending rails, divided goats foot rails etc. Furnishing: - heavy duty heavy duty folding machine, easy to operate - Angle adjustment via electric potentiometer - ELGO NC control unit TYPE 86 for electric backgauge - NC electric backgauge, with rear sheet metal support surface - electric/motorized bending beam - Electric/motorized upper beam .. max. 350 mm - manual lower beam adjustment .. max. 125 mm - manual bending beam adjustment .. max. 125 mm - Upper beam with 2x gui ...

Carriage length: 2800 mm; Cutting width at width fence: 1000 mm; Cutting width at cut-to-length fence: 2800 mm; Cutting depth: Scorer: no; Height adjustment of saw blade: manual / hydraulic; Swivel adjustment saw blade: manual/hydraulic; Adjustment of width stop: manual; Display Saw Blade Angle: Scala; Display cutting height: -; Display Width Stop: Scala; Display Cut-to-length ruler: Scala; Saw blade diameter: RPMs: 4; Motor power: 5.5 kW; Engine brake: yes; Suction connection: 80 mm and 120 mm; Machine length: 3000 mm; Machine width: 1700 mm; Weight:

x-travel: 290 mm y-travel: 150 mm z-travel: 330 mm table surface area: 210 x 600 mm total power requirement: 9,5 kVA weight of the machine ca.: 730 kg dimensions of the machine ca.: 2000 x 2200 x 1655 m The machine is in very good condition and comes from a from a training workshop. Equipment: Safety cover and LED lamp retrofitted in 2016 3-axis active digital readout made by Heidenhain Fixed angle table Coolant equipment Technical data: Longitudinal table movement, motorised / manual 290/300 mm Headstock transverse movement, motorised / manual 150/160 mm Vertical support movement, motorised / manual 330 / 340 mm Work spindle drive 1.5/1.9 kW Number of milling spindle speeds 16 Speed range 40 - 2000 1/min. Horizontal milling spindle Tool holder Standard taper 40 Feed range infinitely variable 5 - 500 mm/min. Creep speed 4 mm/min. Rapid traverse 1200 mm/min. The data for this ad was cre ...

x-travel: 290 mm y-travel: 150 mm z-travel: 330 mm table surface area: 210 x 600 mm total power requirement: 9,5 kVA weight of the machine ca.: 730 kg dimensions of the machine ca.: 2000 x 2200 x 1655 mm The machine is in very good condition and comes from a a training workshop. Equipment: Safety cover and LED lamp retrofitted in 2016 3-axis active digital readout from Heidenhain Fixed angle table Coolant equipment Technical data: Longitudinal table movement, motorised / manual 290/300 mm Headstock transverse movement, motorised / manual 150/160 mm Vertical support movement, motorised / manual 330 / 340 mm Work spindle drive 1.5/1.9 kW Number of milling spindle speeds 16 Speed range 40 - 2000 1/min. Horizontal milling spindle Tool holder Standard taper 40 Feed range infinitely variable 5 - 500 mm/min. Creep speed 4 mm/min. Rapid traverse 1200 mm/min. The data for this ad was created wi ...

CNC milling machine with manual tool change. Designed for milling and engraving workpieces made of solid wood, chipboard, MDF and materials with similar physical properties along the plane (2D milling), as well as artistic milling in 3-dimensional space (3D milling). Manufacturer Vanguard Working field 1300 x 2500 x 200 mm Electrospindle power 6 kW Inverter 7.5 kW Electrospindle speed 18000 rpm Feed speed 50 m/min. Milling speed 25 m/min. Clarity of drawing 0.025 mm Width of linear guides 25 mm (Y), 20 mm (X, Z) Operating voltage 380V 3 phase 50-60 Hz Equipment: DSP controller steel portal Vortex vacuum pump 7.5 kW Separate vacuum clamping system with 6 zones Tool length calibration sensor Drive ball screw pair manufactured by ATLANTA (Germany) Rack-and-pinion drive manufactured by WMH (Germany) Prismatic guides manufactured by HIWIN (Taiwan) Manual central lubricati ...

Make: Future Tech Model: Twin Screw PET / PP / PS Extrusion Line Condition: Excellent – new after testing. Availability: Immediately Materials: PET / PP / PS (Virgin and Recycled Flake) Material Width Range: 0.18mm – 1,2mm Max Sheet Width: 1100mm Output: 1000kg/hour Main Extruder: 95mm Future Tech UV95 twin screw extruder water cooled Co-Extruder: 65mm Future tech single screw with 30kW ac motor & invertor Running from 0.18mm to 1.2mm thick PET up to 1000kg/hr. Mix of virgin, post consumer bottle flake and skeletal flake. 2 Component volumetric blending system for primary and secondary extruders. 95mm Future Tech UW95/44 twin screw extruder water cooled. 250kW ac motor with inverter drive. Triple vented with liquid ring vacuum pump system. Hydraulic screen changer, dual piston, filter dia Φ180mm, manual control. JCTimes model 275 gear pump with ac motor and  ...

Used laboratory dissolver, column dissolver with geared motor and manual speed setting from Italian company Ferri Spa type F30/D. Description: - stepless speed adjustment - manual - manual column lifting with counterweight - current control box with control panel - suitable for small containers - height 1250 mm - width 600 mm - length 750 mm - weight approx. 80 kg - motor power 1 hp - number of engine revolutions 2800 - diameter of dispersing disc: 30/140 mm - voltage: 220/230V

Hydraulic clamping table, Automatic wheel balancer, Fairing, Hydraulic working wheel cover, AEROEL measuring equipment, Hydraulic table clamping, Hoist for 1,000 kg, Electric cabinet cooling, Pneumatic box, Coolant transfer tank, Ø grinding wheel dimensions (od x id x width): Ø 650 x Ø 304,8 x 500mm, Ø min / max to grinding: 3/200 mm, Regulating wheel width: 500 mm, Regulating wheel speed nº: Infinite, Min / max regulating wheel speed (r.p.m.): 10/255 r.p.m., Dressing (auto / manual): Automatic - CNC, Diamond dressing speed: 255 r.p.m., Lubrication (auto / manual): Automatic, Control type ((cnc / manual): CNC, Regulating wheel dimensions (od x id x width): Ø 350 x Ø 203,2 x 500mm, Grinding wheel width: 500 mm, Maximum infeed grinding length: 500 mm, Motor power grinding wheelhead: 55 Kw, Power hydraulic motor: 3 Kw, Total power: 60 Kw, Voltage: 220 / 380V, Long: 2.300 mm, Width: 2 ...

Ø grinding wheel dimensions (od x id x width): 508 x 304.8 x 160 mm, Ø min / max to grinding: 1.5 / 75 mm, Regulating wheel width: 160 mm, Lubrication (auto / manual): Automatic / Automatic, Control type ((cnc / manual): Manual, Regulating wheel dimensions (od x id x width): 304.8 x 190.5 x 160 mm, Grinding wheel width: 160 mm, Maximum infeed grinding length: 160 mm, Motor power grinding wheelhead: 11 Kw, Long: 2.015 mm, Width: 1.280 mm, High: 1.440 mm, Weight: 3.000 Kg.

, Ø grinding wheel dimensions (od x id x width): Ø 650 x Ø 304,8 x 500mm, Ø min / max to grinding: 3/200 mm, Regulating wheel width: 500 mm, Regulating wheel speed nº: infinite, Min / max regulating wheel speed (r.p.m.): 10/255 r.p.m., Dressing (auto / manual): Automatic - CNC, Diamond dressing speed: 255 r.p.m., Lubrication (auto / manual): Automatic / Automatic, Control type ((cnc / manual): CNC, Cnc brand: FANUC, Cnc model: Oi Mate - TD, Regulating wheel dimensions (od x id x width): Ø 350 x Ø 203,2 x 500mm, Grinding wheel width: 500 mm, Maximum infeed grinding length: 500 mm, Motor power grinding wheelhead: 55 Kw, Power hydraulic motor: 3 Kw, Total power: 60 Kw, Voltage: 220 / 380V, Long: 2.300 mm, Width: 2.800 mm, High: 2.100 mm, Weight: 15.000 Kg, Accessories included:

Plongee Portfolio, Cymbal Ports, Speed ​​variator for the traction wheel OPTIONAL: Lead-in slide, CNC, Fairing, Automatic centralized greasing, 1 Year Warranty / Porta plongee rules, Saucers wheel holder, OPTION: Porta rules enfilade, cnc, protection,, automatic lubrication system, 1 year warranty, Ø grinding wheel dimensions (od x id x width): Ø 406 x Ø 203 x 200 mm, Ø min / max to grinding: 1.5 / 100 mm, Regulating wheel width: 200 mm, Regulating wheel speed nº: infinite, Min / max regulating wheel speed (r.p.m.): 0/450 rpm, Lubrication (auto / manual): Automatic, Control type ((cnc / manual): CNC, Cnc brand: FANUC, Cnc model: Oi Mate - TF, Infeed (auto / manual): Automatic, Regulating wheel dimensions (od x id x width): Ø 270 x Ø 140 x 200 mm, Grinding wheel width: 200 mm, Maximum infeed grinding length: 200 mm, Motor power grinding wheelhead: 15 kW, Long: 2020 mm, Width: 1 ...

Ø grinding wheel dimensions (od x id x width): Ø 406 x Ø 203 x 200 mm, Ø min / max to grinding: 1.5 / 100 mm, Regulating wheel width: 200 mm, Min / max regulating wheel speed (r.p.m.): 10/250 rpm, Control type ((cnc / manual): Manual, Infeed (auto / manual): Automatic / Automatic, Regulating wheel dimensions (od x id x width): Ø 270 x Ø 140 x 200 mm, Grinding wheel width: 200 mm, Maximum infeed grinding length: 200 mm, Motor power grinding wheelhead: 15 kW, Long: 2020 mm, Width: 1300 mm, High: 1420 mm, Weight: 4200 Kg, Accessories included: Automatic Hydraulic Plongee, Diamond Compensator, Plongee Porter, Saucer Cymbal, Speed ​​Variator for the traction wheel OPTIONAL: Lead-in Trimmer, Cowling, Automatic Centralized Lubrication, 1 Year Warranty / Automatic hydraulic Plongee, Diamond compensator, Porta plongee rules , Saucers wheel holder, OPTION: Porta rules enfilade, protectio ...

Plongee automatic hydraulics, Refrigeration equipment, Plongees knife, Cymbal grinder, OPTIONAL: Lead-in grinder, CNC, Fairing, Gearbox elimination and Adaptation of speed variator for drag wheel, Automatic centralized lubrication, 1 Year Warranty / Plongee automatic hydraulic, refrigeration equipmentPorta plongee rules, Saucers wheel holder, OPTION: Porta rules enfilade, cnc, protection, eliminating gearbox and variable speed adjustment for wheel drive, 1 year warranty, Ø grinding wheel dimensions (od x id x width): 325 x 175 x 125 mm, Ø min / max to grinding: 1.5 / 50 mm, Regulating wheel width: 125 mm, Regulating wheel speed nº: infinite, Control type ((cnc / manual): Manual, Infeed (auto / manual): Automatic / Automatic, Regulating wheel dimensions (od x id x width): 220 x 125 x 125 mm, Grinding wheel width: 125 mm, Maximum infeed grinding length: 125 mm, Motor power grinding whee ...