Hydraulic Presses used for sale (113)

Key data: 400 t, 1000 mm

LAUFFER PRESSES hydraulic press model VA 400 Capacity 400 tons Table 700x1000 mm Possible to inspect under power

Key data: 600 t, 800 mm, 650 mm

LCM Taiwan, 600 tons hydraulic press New in 12/2014 Table 800x800 mm Stroke 0-650 mm adjustable full specifications attached Possible to inspect under power

Key data: 250 t, 800 mm, 650 mm

LCM Taiwan, 250 tons hydraulic press Possible to inspect under power New in 2014 Table 800x800 mm Stroke 0-650 adjustable

Manual gantry press 20 tons Overall dimensions: 1200 x 800 x 500 mm Weight: 100 kg Auction-ID: A7-50798-224

Key data: 40 t, 450 mm, 160 mm

Press force 400 kN , table 450x560 , ram 375x300 , distance table joints 340 stroke 160 , puncture hole 100 diameter, silky column passage 220x410

CONTROLS  PLC SIEMENS S7-400 PRESS DESIGN  drive system: hydraulic   number of suspensions: 1   slide ejectors / cushion: no   table cushion: no   opening in table: no   feedstock transport direction: back-front PRESS FORCES  total force (nominal): 1000 toPRESS TABLE  table surface (left-right): 2066 mm  table surface (front-back): 2000 mm  height above floor level: 630 mmSLIDE  stroke: 900 mmSLIDE (HYDR. PRESS)  approximation velocity max.: 600 mm/s  working velocity min.: 15 mm/s  working velocity max.: 40 mm/s  return velocity max.: 390 mm/s  return force: 100 toTOOL ASSEMBLY DIMENSIONS  shut height (stroke down, adjustment up), BDC: 1710 mm  distance table - slide max.: 1700 mmELECTRICAL SPECIFICATIONS  total power consumption: 160 kW  mains voltage: 400 V  mains frequency: 50 HzDIMENSIONS / WEIGHTS  height above floor level: 6500 mm  t ...

FRITZ MÜLLER ZE 625-4 hydraulic press was built in Germany by Fritz Müller GmbH & Co. KG. The machine has been continuously maintained and upgraded throughout its service life. The first major overhaul was carried out in 1988 by the manufacturer’s service Machinenfabrik Mueller-Weingarten AG. A second overhaul was carried out in 2020, during which the press was brought up to current safety requirements. As part of this overhaul, a new control system based on a SIEMENS SIMATIC S7 PLC controller and a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel was installed, the entire electrical system was replaced, seals were replaced and light curtains were installed. The FRITZ MULLER ZE 625-4 is an extremely versatile press designed for even the most demanding metal forming operations. It is capable of performing operations such as deep drawing, stamping, forging, straightening large w ...

CONTROLS  PLC SIEMENS S7 300 PRESS DESIGN  drive system: hydraulic PRESS FORCES  total force (nominal): 800 toPRESS TABLE  table surface (left-right): 2000 mm  table surface (front-back): 2000 mm  height above floor level: 700 mmSLIDE  table surface (left-right): 2000 mm  table surface (front-back): 2000 mm  stroke: 900 mmSLIDE (HYDR. PRESS)  approximation velocity max.: 400 mm/s  working velocity min.: 5 mm/s  working velocity max.: 160 mm/s  return velocity max.: 300 mm/sTOOL ASSEMBLY DIMENSIONS  shut height (stroke down, adjustment up), BDC: 1700 mm  distance between columns (H-frame): 2100 mmELECTRICAL SPECIFICATIONS  total power consumption: 370 kW  mains voltage: 400 V  mains frequency: 50 HzDIMENSIONS / WEIGHTS  total weight approx.: 81000 kgATTACHMENTS (PRESSES)  press automation: yes   gripper transfer system: yes   acc. to actual acci ...

Key data: 200 t, 80 mm

Inv. Num. : 9036 Type: 200 T Producer: ROSS Created: 2003 Parameters: Control system: DIMECO MCU 24 Compressive force: 200 t Table length: 2100 mm Table width: 1000 mm Stroke: 80 mm Adjusting the ram: 150 mm Machine weight: 36700 kg

CONTROLS  conventional PRESS FORCES  total force (nominal): 160 toPRESS TABLE  table surface (left-right): 1000 mm  table surface (front-back): 850 mmSLIDE  stroke: 705 mmTOOL ASSEMBLY DIMENSIONS  shut height (stroke down, adjustment up), BDC: 1205 mmMachine hours: 78571

DIEFFENBACHER PO 500A hydraulic press was built in 1978 in Germany by J. Dieffenbacher GmbH & Co. The machine has been regularly maintained and upgraded throughout its service life. In 2017, a major upgrade was carried out, which included replacing the electrical cabinet, installing light curtains and adding a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel. The seals and electrical system were also replaced. The DIEFFENBACHER PO 500A is the perfect choice for even the most demanding metal forming operations. It enables the execution of such operations as die stamping, punching, calibration of forgings and hot and cold bending. All these machining processes are performed with a high press force of up to 500 tonnes, which, combined with a highly dynamic slider, guarantees the best machining results. The machine is also characterised by a rigid body made of thick steel plates and a ...

Factory Number 056-005/1Machine Type Hydraulic Single-Column PressPress Force 1,600 kN / approx. 160 tTable Size 900 × 630 mmRam Surface 750 × 450 mmMax. Installation Height / Opening 800 mmMin. Opening 300 mmRam Stroke 500 mmHydraulic Pressure 160 barConnected Load 11 kWConnection Voltage 400 V / 50 HzControl Voltage AC 230 VRated Current 24 ASupply Line Fuse 50 ACE Marking

DIEFFENBACHER PO-F 1250 A hydraulic press was built in Germany in 1981 by J. Dieffenbacher GmbH & Co. The machine was regularly maintained and upgraded throughout its service life. In 2016, a major upgrade was carried out, which included replacing the electrical cabinet, installing light curtains and adding a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel. The piston seals were also replaced and measuring scales were added for precise position measurement of the slider, top ejector and lower die cushion. The DIEFFENBACHER PO-F 1250 A is an extremely versatile hydraulic press for demanding metal forming applications. Its main purpose is die stamping of steel components, calibration of forgings, dogging, hot and cold forging, cold forming and other operations that require very high press forces. All these machining processes are performed with a high press force of up to 1250 tonn ...

Hydraulic single-column press with 25 t pressing force and 4 kW drive power. Machines are generally offered without documentation. If documents are available, they will be attached to the respective machine.

Hydraulic Press DEGUMA P12-12 II

CONTROLS  PLC SIEMENS SIMATIC OP 27 PRESS DESIGN  table cushion: yes PRESS FORCES  total force (nominal): 300 toPRESS TABLE  table surface (left-right): 1800 mm  table surface (front-back): 1000 mmSLIDE  stroke: 600 mmSLIDE (HYDR. PRESS)  return force: 38 toDIE CUSHION (TABLE CUSHION)  stroke: 200 mmTOOL ASSEMBLY DIMENSIONS  shut height (stroke down, adjustment up), BDC: 1000 mmDIMENSIONS / WEIGHTS  total weight approx.: 43000 kg

Key data: 600 t

Max Tool length: 3000mm Max Tool Width: 2000mm Min Tool Height: 500mm Total Tool Weight: 20,000kg Max Closing Speed: 400 mm/sec

Press force: 16,000 kNMax. ram stroke: 1,700 mmMax. opening between table and ram: approx. 2,450 mmMin. opening: 770 mmRam plate: 4,500 × 2,500 mmTable size: 4,500 × 2,500 mmRapid traverse: 350 mm/sWorking speed at 66% press force: 23 mm/sWorking speed at 100% press force: 13 mm/sMax. return speed: 220 mm/sMax. retraction force: 1,600 kNRam cushion:Force: 2,000 kNStroke: 150 mmPressure plate: 3,650 × 1,580 mmTable cushion:Force: 2 × 1,000 kN or 3 × 500 kNStroke: 300 mmPressure plate: 1,550 × 700 mmDrive:Main motors: 2 × 132 kWMotor filter unit: 4 kWMotor speed: 1,500 rpmSuitable for demanding forming, deep drawing, and pressing operations with large tools and high press forces.

Inv. Num. : 948 Type: LVH 2500 Producer: ŽĎAS Created: 1961 Parameters: Depth: 1800 mm Width: 3450 mm Height above ground: 4650 mm Weight: 85 000 kg Voltage: 220 / 380 V Mains frequency: 50 Hz Workforce: 2500 t Number of strokes: 20/min Height of the lifts: 500 mm Minimum plunger distance from the table: 900 mm Maximum plunger distance from the table: 1400 mm Table surface: 1050 x 1400 mm Plunger area: 1050 x 1200mm

EXNER EXSBRD 500ET Hydraulic PressGeneral DataManufacturer: Maschinenfabrik EXNER GmbH & Co. KGType: EXSBRD 500ETYear of Manufacture: 2001Machine No.: 10461Technical DataPress Force: 5,000 kN / 500 tMax. Stroke Length: 1,300 mmMax. Opening: 1,800 mmMin. Opening: 500 mmTable Size: 2,550 × 2,000 mmColumn Clearance: 2,570 mmTool DataMax. Tool Dimensions: 2,200 × 1,800 mmMax. Tool Weight: 25,000 kgSpeedsWorking Speed: 26 / 50 mm/sRapid Traverse Speed: 400 mm/sAdditional Technical DataOverrun Distance: 97 mmOverrun Time: 158 msSafety Distance: 252 mmDrive Power: 159 kWOil Capacity: approx. 2,800 l

Key data: 630 t, 275 mm

For sale is a used lowering press, manufacturer Sack + Kiesselbach, type EP 630. The machine is in very good condition. The press worked in an engraving company as a test press. Technical data: Pressing force: max. 630 tons. Installation height: max. 325 mm Stroke: max. 275 mm Weight: 4,000 kg

CONTROLS  PLC SIEMENS S7 PRESS DESIGN  drive system: hydraulic PRESS FORCES  total force (nominal): 300 toPRESS TABLE  table surface (left-right): 2200 mm  table surface (front-back): 1700 mmSLIDE  stroke: 1600 mmTOOL ASSEMBLY DIMENSIONS  shut height (stroke down, adjustment up), BDC: 1600 mmELECTRICAL SPECIFICATIONS  mains voltage: 400 V  mains frequency: 50 HzDIMENSIONS / WEIGHTS  space requirements -left/right-: 6536 mm  space requirements -front/back-: 2923 mm  total height: 6135 mm  total weight approx.: 36000 kg

Key data: 250 t

Inv. Num. : 8652 Type: ZHS 250 Producer: ŽDB Hydraulika Generated: 2000 Parameters: Compressive force: 250 t Table length: 3500 mm Table width: 1200 mm Stroke: 700 mm Ram dimensions: 3500 x 1200 mm Working speed: 13-60 mm/s Machine height: 6000 mm Machine length: 3000 mm Machine width: 5000 mm Machine weight: 60000 kg

pressure: 6 tdistance between columns: - mmstroke: - mmtotal power requirement: - kWweight of the machine ca.: 1 tdimensions of the machine ca.: 1 x 1 x 2 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 3 t, 150 mm

For sale in new condition HYUNDAE CETTA HHP-3 hydraulic press "more pieces" manufacturer: HYUNDAE "Korea" type: HHP-3 year of manufacture: 2018 load range: 1-3 tons Stroke [mm] 150 open height: 250 mm -safety light gate -two-handed operation .-mobile work table Hyundae press control Pressing rod closing speed: 178mm/sec Pressing rod pressing speed: 54mm/sec Opening speed 79 mm/s Table size: 450x360mm Max. Working pressure: 60kg·f/㎠ Hydraulic motor 1,5 kW 3 phase/4P 200v Weight: 350kg machine height "without table": 1415mm machine length: 950mm machine width: ca 700mm working table with casters or level bolts

pressure: 250 tthroat: 360 mmtable-size: 1.250 x 630 mmtable diameter: 250 mmdimension of ram: 850 x 450 mmdayligth: 800 mmpiston stroke: bis 500 mmdiameter of piston: 400/360 mmram stroke speed: abwärts 200 mm/secram stroke speed: aufwärts 110 mm/sectotal power requirement: 20,5 kWweight of the machine ca.: 8 tPress force: 250 tThroat depth: 360 mmTable size: 1,250 × 630 mmTable opening diameter: 250 mmRam clamping surface: 850 × 450 mmInstallation height (daylight): 800 mmRam stroke: up to 500 mmMain cylinder diameter: 400 / 360 mmRam speed (downward): 200 mm/sRam speed (upward): 110 mm/sTotal power requirement: 20.5 kWMachine weight: approx. 8 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 5 t, 150 mm

Hydraulic Press Atsugi AP-5-KL Used Load Range: 20-50 (kN) Stroke (mm): 150 Lower Speed ​​(Approach Fast Speed: 350 (mm/s) Lower Speed ​​(Under Pressure Slow Speed: 36mm/s Rise Speed ​​250 (mm/s) Working Area Open Height: 250mm Open Depth: 180mm Table Size: 450x50mm Motor Specification 3 Phase AC200V 4P 1.5KW Two-Hand Operation . Mobile Worktable Fuel Oil / Quantity Daphni Hydraulic 46/9L Total Weight (kg) 270 Body Size ​ Height (mm) 986 Width (mm) 485 Depth (mm) 920

pressure: 250 tthroat: 360 mmtable-size: 1.250 x 630 mmtable diameter: 250 mmdimension of ram: 850 x 450 mmdayligth: 800 mmpiston stroke: bis 500 mmdiameter of piston: 400/360 mmram stroke speed: abwärts 200 mm/secram stroke speed: aufwärts 110 mm/sectotal power requirement: 20,5 kWweight of the machine ca.: 8 tPress force: 250 tThroat depth: 360 mmTable size: 1,250 × 630 mmTable opening diameter: 250 mmRam clamping surface: 850 × 450 mmInstallation height (daylight): 800 mmRam stroke: up to 500 mmMain cylinder diameter: 400 / 360 mmRam speed (downward): 200 mm/sRam speed (upward): 110 mm/sTotal power requirement: 20.5 kWMachine weight: approx. 8 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 8438 Type: AF-200-75 Producer: Arisa Generated: Parameters: Maximum retraction speed: 200 t Top table length: 950 mm Top table width: 750 mm Maximum number of strokes: 20 1/min Ram stroke: 250 mm

pressure: 2 tdistance between columns: - mmstroke: ? mmthroat: ? mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mhydraulic press 2tDrive: 0The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 2200 t

Qty. 1 Second-hand extrusion press – 2200 MT Mfc.: Breda Danieli Built: 2016 Status: still in production Max. Extrusion Force: 21,9 MN at 300 bar Max. working pressure: 310 bar Type of press: back loading with 2 containers Billet size 8” - length: 300 – 1,200 mm Scope of supply: complete extrusion press in working order with hydraulic and electric system Overhead pinch billet manipulator Material: AL 6000 Series Out of the scope of supply: floor frame mounted in the concrete floor all dies and tooling bolsters

pressure: 160 tstroke: 500 mmtotal power requirement: 20,5 kWweight of the machine ca.: 7,5 tRated force: 160 Mp (˜ 1600 kN / 160 tons)Operating pressure: 144 kp/cm²Speed:Downward: 200 mm/sUpward: 250 mm/sRam stroke: 500 mmThroat depth: 360 mmMax. distance (table to ram): 800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

ULTRAPRAS WKR70H hydraulic press built in 2021 by the Polish company SAKOMET is designed for even the most demanding cold metal forming operations. The operations, such as precise cutting, stamping, punching and extruding of workpieces, are performed with a force of 16 tonnes using a hydraulic cylinder with a diameter of 100 mm. Induction limiters additionally allow adjustment of the piston advance and retraction limits, making the machine adaptable to the working range of various tools. In turn, centrally beneath the piston is a large cross-cut work table with a 90mm diameter bore. The UltraPras WKR 70H 16t hydraulic press weighs 420 kg. Technical specifications of the ULTRAPRAS WKR70H press - press force: 16 t - piston stroke: 70 mm - piston diameter: 100 mm - maximum working speed: 9.8 mm/s - minimum working speed: 2 mm/s - return speed: 20 mm/s - work table dimensions (L x  ...

pressure: 60 tdistance between columns: 550 mmstroke: 150 mmtotal power requirement: 11 kWweight of the machine ca.: 5 tdimensions of the machine ca.: 3 y 3 x 2,5 mNo. 4105Hydraulic pressCompressive force max. 600 kNRam stroke 150 mmWeight approx. 4500 kgTable 500 x 400 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 7796 Type: HSA 200 T Producer: Hidroliksan Created: 2022 Parameters: Operating hours: 1600 h Compressive force: 200 t Maximum stroke: 450 mm Top table length: 1600 mm Top table width: 1400 mm Speed (high): 250 mm/s Speed (down): 160 mm/s Working speed: 5-18 mm/s Machine height: 5000 mm Machine length: 3650 mm Machine width: 3400 mm Machine weight: 18,000 kg

pressure: 63 tdistance between columns: 360 mmstroke: 400 mmweight of the machine ca.: 4 tdimensions of the machine ca.: 1.8x1.6x2.7 mwww.marcels-maschinen.chThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

ULTRAPRAS UPV100TT SPECIAL hydraulic press built in 2022 Poland is the perfect choice for a range of demanding cold metal forming operations. This highly efficient and versatile machine can perform such operations as precision bending, profiling, flattening, bending, hole punching and stamping. Inside the robust design, there is a power unit-powered hydraulic piston with a diameter of 220 mm, which performs all these machining processes with a high press force of 100 tonnes. In addition, the entire working area is protected by light curtains, thanks to which the UltraPras four-column press also offers a high level of operational safety. During its service life, the machine has operated for just 595 hours and completed a total of 37042 work cycles. The UPV 100 TT SPECJAL 100t hydraulic press weighs 6500 kg. Technical specifications of the ULTRAPRAS UPV100TT SPECIAL press - maximum pre ...

CONTROLS  conventional PRESS FORCES  total force (nominal): 800 toSafety distance 141 mm, maximum overrun 39 mm, rapid lowering speed 400 mm/s

Key data: 250 t

Catalog No. : 7693 Type: CD 250 Producer: Mecamaq Made in: 2022 Characteristic: Pressing force: 250 t Maximum stroke: 250 mm Machine weight: 3200 kg

CONTROLS  electronic controls PRESS DESIGN  drive system: hydraulic   frame design: 4 column   number of suspensions: 1   slide ejectors / cushion: yes   table cushion: yes PRESS FORCES  total force (nominal): 200 toPRESS TABLE  table surface (left-right): 1330 mm  table surface (front-back): 1150 mm  height above floor level: 850 mm  opening in bed (diameter): 250 mmSLIDE  slide force: 200 to  table surface (left-right): 1200 mm  table surface (front-back): 1200 mm  stroke: 800 mmSLIDE (HYDR. PRESS)  approximation velocity max.: 300 mm/s  working velocity min.: 30 mm/s  return velocity max.: 400 mm/s  return force: 200 toSLIDE EJECTOR / CUSHION  working principle: hydraulical   nominal force: 30 to  stroke: 130 mmDIE CUSHION (TABLE CUSHION)  cushion force: 30 to  stroke: 850 mmELECTRICAL SPECIFICATIONS  mains voltage: 400 V  mains freq ...

HUNGER Maschinenbau GmbH Press cylinder for a hydraulic metal scrap press / scrap press shear (Metso-Lindemann) fully assembled and ready for installation Piston diameter 260mm Piston rod diameter 210mm Stroke 8910mm Outer diameter of the housing 335 mm Cylinder head diameter 365mm Total length 10,635 mm Working pressure cylinder head 180 bar Working pressure cylinder base 225 bar Test pressure cylinder head 250 bar Test pressure cylinder base 315 bar Maximum pressure force 1195 kN Maximum tensile force 332 kN Medium hydraulic oil ISO VG46 Installation position horizontal

PRESS FORCES  total force (nominal): 1000 toPRESS TABLE  table surface (left-right): 1800 mm  table surface (front-back): 1300 mmSLIDE  stroke: 500 mm

Offer 20202 Specifications: - max. pressing force 35 t - Projection to the middle of the ram 240 mm - Working height adjustable with hand crank 540 to 940 mm - 2 Hand control - Protective shield enclosure with light barrier - Material - Slide-in device - Pneumatic connection - Press control via SIEMENS SIMATEC OP 7 - Drive 400 V / 15.5 kW - Space requirement approx. W 1200 x H 2000 x D 2400 mm - Weight approx. 2500 kg

CONTROLS  PLC SIEMENS SIMATIC OP 27 PRESS DESIGN  table cushion: yes PRESS FORCES  total force (nominal): 300 toPRESS TABLE  table surface (left-right): 1800 mm  table surface (front-back): 1000 mmSLIDE  stroke: 600 mmSLIDE (HYDR. PRESS)  return force: 38 toDIE CUSHION (TABLE CUSHION)  stroke: 200 mmTOOL ASSEMBLY DIMENSIONS  shut height (stroke down, adjustment up), BDC: 1000 mmDIMENSIONS / WEIGHTS  total weight approx.: 43000 kgEl. cabinet (Ritta)Machine hours: 46131

Hydraulic press

CONTROLS  PLC SIEMENS SIMATIC OP 27 PRESS DESIGN  table cushion: yes PRESS FORCES  total force (nominal): 300 toPRESS TABLE  table surface (left-right): 1800 mm  table surface (front-back): 1000 mmSLIDE  stroke: 600 mmSLIDE (HYDR. PRESS)  return force: 38 toDIE CUSHION (TABLE CUSHION)  stroke: 200 mmTOOL ASSEMBLY DIMENSIONS  shut height (stroke down, adjustment up), BDC: 1000 mmDIMENSIONS / WEIGHTS  total weight approx.: 43000 kgEl. cabinet (Ritta)Machine hours: 32510

SMG DS 315-1500/1300 CNC hydraulic press was manufactured in 1984 in Germany. The machine, consisting of two interconnected stations, is used for pressing metal workpieces in manual, semi-automatic and automatic mode with a pressing force of up to 315 tonnes. All the machine’s machining parameters are set using a CNC control with a full-colour, touchscreen display. The press is equipped with a hydraulic and pneumatic sheet metal feeder, servo drives for feed rollers to set a very precise stroke of up to 0.1 mm, safety cages and workpiece feed and drop control sensors. The SMG 315 T machine underwent a complete overhaul in 2007, during which components such as pumps and safety installations were replaced. Technical data of the SMG DS 315-1500/1300 press - maximum press force: 315 t - working table dimensions (L x W): 1500 x 1300 mm - upper machine point (from the table): 750 mm ...

CONTROLS  PLC SIEMENS SIMATIC OP 27 PRESS DESIGN  table cushion: yes PRESS FORCES  total force (nominal): 300 toPRESS TABLE  table surface (left-right): 1800 mm  table surface (front-back): 1000 mmSLIDE  stroke: 600 mmSLIDE (HYDR. PRESS)  return force: 38 toSLIDE EJECTOR / CUSHION  stroke: 200 mmTOOL ASSEMBLY DIMENSIONS  shut height (stroke down, adjustment up), BDC: 1000 mmDIMENSIONS / WEIGHTS  total weight approx.: 43000 kgEl. cabinet (Ritta)Machine hours: 47037