grinding machines wood used for sale (665)

Manufacturer: DMC Breitbandschleifmaschine, Type: Topsand, Year: 1994, Monting of the machine: Walze/Schuh/Schuh/Bürste, Sanding width mm: 1300, Sanding hight mm: 120, Number of sanding belts: 3, Sanding belt dimensions: 2620 X 1350, Rubber roller: 1, Shore roller 1: ca.85, Längsschleifaggregate: 22,5, Belt 2 shoe unit: 15, Belt 2 synchronous and reverse run: 15, Belt 4 pressure segment belt: no, Combi unit roller/shoe: 8-25, Table hight adjustment by engine: ca.5, Abrasive belts at bottom: yes, Intermediate sanding of lacquer: yes, Programmanwahl extern: Struckturbürste von unten, Vacuum table: Bürste, Pressure pads for short workpieces: 180, Segment sanding shoe: von Unten, Year :1994

Manufacturer: Arminius, Type: ST 2, Year: 1991, Control: Hand, Table length: 2000, Work piece hight min-max mm: 10-60, Feeding speed min-max m/min: 5-25, Controllable slewable: yes, Number of sanding units: 2, 1st sanding motor controlled and tiltable: Schleifscheiben Typ Arminius, Power kW: 1,1, 2nd sanding motor controlled and tiltable: Schleifscheiben Typ Arminius, Power kW: 1,1, Power kW: 1,1, Power kW: 1,1, Control panel at bottom: yes, Hight adjustment by hand wheel: yes, Year :1991

Manufacturer: Evimatic, Type: HF 82 CB, Year: 2000, Control: yes, Control: yes, Work piece width min-max mm: min. 200, Schleifaggregate rechts : 2, Unit 1 tiltable: yes, Aggregat 1 kW: ca. 1,5, Unit 2 slewable: yes, Aggregat 2 kW: ca.1,5, Number of frequency controlt belts: 2, Brushing unit: 1, Total lenght mm: 2500, Year :2000

Manufacturer: Johannsen, Type: Langbandschleifer, Year: 1992, Table width mm: 800, Table length: 2799, Hight adjustment by engine: yes, Sanding belt engine kW: 4, Travel range table mm: 350, 2 rotary directions: yes, Exhaust diameter mm: 140, Hight adjustment by engine: yes, Year :1992

Manufacturer: Johannsen, Type: T 94, Year: 1993, Sanding hight mm: 350, Table width mm: 800, Table length: 2700, Hight adjustment by engine: yes, Sanding belt engine kW: 4, 2 rotary directions: yes, Exhaust diameter mm: 120, Hight adjustment by engine: yes, Year :1993

NTS 201 Wet Grinder Whetstone diameter 200 mm Whetstone width 40mm Pull-off wheel width 30mm Pull-off wheel diameter 200mm Speed 115 rpm LxWxH: 480 x 340 x 375mm 0.15kW 230V 50Hz Weight 9.2kg G&STÜ-5750201

NTS 256 Wet Grinder Whetstone diameter 250mm Sharpening stone width50mm Pull-off wheel diameter 200mm Speed 90 – 160min ̄¹ Weight (net) approx. 14.2kg Input power 0.15kW S1 Connection voltage 230V Mains frequency 50Hz SCOPE OF DELIVERY Water tank Peeling paste Angle gauge Universal grinding device G&STÜ-5750256

PART NUMBER: 7514 Specifications: - max width of the workpiece 900mm - max height of the workpiece 160mm -in advance: - metal roller, slip - aggregate - grooved metal roller for calibration + shoe + metal roller - rubber roller, slip - from below: - 2 metal rollers, slip - Pulling strap - 2 metal rollers, slip - pneumatic oscillation of the belts - 2 types of feed speeds - electric table lifting - brake - grinding thickness potentiometer - main motor 11kW - working pressure 6-8bar - diameter of the extraction spigot 160mm - dimensions length/width/height 1600x1450x1800mm – weight 820kg ADVANTAGES – Italian production – unpainted – used grinder, very good condition Net price: 28900 PLN Net price: 6721 EUR depending on the price of 4.30 EUR (Prices may change with higher fluctuations)

PART NUMBER: 7549 Specifications: - max width of the workpiece 1100mm - max height of the workpiece 170mm 2 units: 1) grooved rubber roller for calibrating 2) rubber roller + boot boot + metal roller –in advance: - metal roller, slip - aggregate - metal roller, slip - A unit with a shoe - metal slip outfeed roller – from below: - Pulling strap - pneumatic oscillation of the belts - electric lifting of the table top - 2 types of feed speeds - 11kW motor - with pneumatic brake - working pressure 6-8bar - extraction spigot diameter 2x150mm - total dimensions length/width/height 1960x1700x2000mm - weight about 2000kg ADVANTAGES – made in Germany – 2 units – unpainted – used grinder, very good condition Net price: 34900 PLN Net price: 8116 EUR depending on the price 4.30 EUR (Prices may change with higher fluctuations)

Satin sander COSTA LEVIGATRICI model S A2 TS 1350 : – with electronic PCM control and touch-screen video – useful working width 1350mm – useful working thickness from 3 to 160mm – variable feed speed from 5 to 25 m/min – with perforated belt and depressor – n° 1 belt unit with pad, 2620mm belt development, with air blowers belt cleaning – n° 1 scotch-brite group (inside the machine) Year 2000, CE regulations

from training workshop - public institutionused, top condition, little usedmake Johannsentype T 94year of manufacture 1996machine no.No. 21397GS wood dust testedsanding length approx. 2600 mmsanding width approx. 850 mmbelt length approx. 7800 mm x 150 mmcranking right approx. 550 mmelectric adjustmentupper belt coverupper sanding supportbelt speeds 22 m/sec.right-left runsuction connection D 180 mm leftspace requirement approx. 2200 mm x 4050 mmweight approx. 700 kgstorage location 97447 Gerolzhofen, free loaded, unpackeddelivery as seen,without guarantee and warranty

Code: 0026 Brand: GNT - ITALY Model: S 1300/2 Automatic cleaning machine for top and bottom surface cleaning of melamine covered panels, laminate, pvc, etc. Composition: Steel base Top and bottom cleaning unit composed of : dusting brush of special wire for dust elimination, wiping blade for residue cleaning, humidifyng group with one rubber and one milled metal roll, two brushes for finishing - reservoir for the cleasing liquid, recirculation pump made of stainless material Independent brush and felt rolls control to get back wearing down Motorvariator with continuous adjustment for advancement Motorvariator with continuous adjustment for humidifyng unit Brushes to clean the finishing felt rollers Residue collection tanks Emergency device to check thickness Technical data Working width mm 1300 Working height mm 6/80 Feed speed from 5 to 20 mt/min Working  ...

SCM Sandya Uno wide belt sander Working width 900mm Working height 150mm 1 sanding unit Sanding unit with boots Two grinding speeds Electric raising and lowering of the sanding unit Pneumatic oscillation New carpet Motor power 4kw CE Certified

internal diameter: min / max: 10 / 250 mmgrinding depth: 400 mmexternal diameter: max. 380 mmswing dia.: 390 mmtable:: table travel: max. 550 mmstroke of the table: min. 2 mmrapid traverse: 10 m/mintable speed -stepless-: 0 - 10 m/minrough adjustment: 18 mmfine adjustment: 4 mmmax. workpiece weight: 100 kgWorkhead.: spindle head: B 6 DIN 55021spindle turning speed - stepless: 15 - 1.500 U/minpivoting angle: +/- 30 Gradspindle bore: 50 mmpower capacity: 2 kWinternal grinding:: rapid traverse: 0 - 250 mm/minstroke: 70 mmpower requirement: 3 kWtotal power requirement: kWweight of the machine ca.: 2,7 tdimensions of the machine ca.: 3,0 x 3,0 x 3,2 mDocuments: exhaust fan: Fibaron paper band filter: Polo Fire extinguish system: Deugra Internal Grinding MachineBAHMÜLLER - JES 12The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

400 V, 50 Hz, 5 A, 2.2 Kw, H 1380 mm, W 1000 mm, L 2510 mm, 330 kg, Belt speed 28 m/s, Table 700x2200 mm, Abrasive belt 6000x150, Height adjustment 540 mm, Extraction connection 120 mm, Vacuum 550 Pa, volume flow 815 m³/h

Wide belt grinding machine Boere Elite 1300 BK Grinding width max. 1300mm Grinding calibration roller from below

Wide belt grinding machine OTT RS-O Grinding width: 1300mm Calibration roller + fine sanding + cleaning brush

Wide belt sanding machine for wood, veneer and varnish Ernst LBK 1300 Grinding width: 1300mm Transverse grinding unit Longitudinal grinding unit

width of the strips: 75 mmband length: 2000 mmband speed: 37 m/mintotal power requirement: 3 kWweight of the machine ca.: 0,084 tdimensions of the machine ca.: 1x0,5x1 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Power connection 380V 7.3kW Extraction 1x120 mm 1x180 mm Grinding table 2850 x 1550 mm Sanding belt dimensions 7820 x 150 mm Table height adjustment via handwheel LxDxH: 4400 x 1700 x 1450 mm Weight approx. 1100 kg

Key data: 1300 mm, 4 , 150 mm

WIDE BELT GRINDING AND CALIBRATION MACHINE Technical details: Working width: 1300 mm Max. workpiece thickness: 150 - . 4.0 mm Sanding belt dimensions: Circumferential mm Machine dimensions LxWxH: 4.8 x 2.7 x 2.35 m Drive 219 kW Year of construction 1992/2004 For woodworking! Other features: - Pneumatic belt guide - Height adjustment by handwheel - EMERGENCY STOP switch - Grinding roller adjustment - Belt tensioner - Roller conveyors (infeed and outfeed per L: 2800 x W: 1700 mm with 6 rollers each) motor-driven - Control panel operation - Workpiece thickness min./max.: 4.0/150mm - Sanding belt belt width 1300 mm (belt circulation) - Sanding belt support lengthxwidth: 1700/1350 mm

width of the strips: 75 mmband length: 2000 mmband speed: 37 m/mintotal power requirement: 3 kWweight of the machine ca.: 0,11 tdimensions of the machine ca.: 1x0,5x1 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 1100 mm, 1 , 150 mm

Combination grinding unit with contact roller and air grinding shoe Brush roller Abrasive belt tension, pneumatic motor strength adjustment Specifications: max. working width 1100 mm Max. workpiece thickness 150 mm Min. workpiece thickness 3 mm Sanding belt dimensions 1900 x 1120 mm Feed speed 5/10 m/min. Motor power grinding unit 15 kW Motor power height adjustment 0.50 kW Motor power feed carpet 0.5/1.0kW Operating pressure 6 bar Air pressure approx. 20 l/min Suction nozzle 2 x 200 mm Weight approx. 2100 kg Machine width approx. 1750 mm Cntaou7R Machine depth approx. 1700 mm Machine height approx. 1900 mm

Key data: 110 mm, 1 , 160 mm

Specifications: max. working width: 1100 mm, min./max. workpiece thickness: 3 / 160 mm Sanding belt dimensions: 2150 x 1120 mm, sanding belt speed: 18 m/sec. Feed speeds: 4 + 8 m/min. Motor power grinding agregate: 11 kW, power adjustment: 0.55 kW, feed carpet: 1.3/1.8 kW Operating pressure: 6 bar, Air requirement: 10 l/min., Suction nozzle: 1 x 150 + 1 x 120 mm WxDxH: 1800 x 2000 x 2100 mm, weight approx. 2400 kg Standard equipment: - Contact roller D=150 mm, hardness 90° Shore - Air sanding shoe with automatic insertion and removal - Rigid sanding shoe for solid wood frame sanding - Brush roller driven by the grinding unit - Automatic centering of the feed carpet - Extension carpet with high quality rubber circular hole carpet and auto. Carpet centering - Pneumatic sanding belt tension with length compensation - Non-contact abrasive belt oscillation, electronic - Low ...

Key data: 1350 mm, 3

electronic control - First roller D=250 mm made of grooved steel - Second roller D=320 mm made of rubber - third roller D=? mm made of steel with carpet with button - Pneumatic on/off of the 3 groups - Air purification fan on the 3 bands - Sanding belt 2620 mm - Electronic oscillation of the abrasive belts - Automatic layer positioner - Variable feed speed of the carpet with inverter KW 2.2 - Vacuum conveyor belt - ionization in the outlet

grinding length: 600 mmgrinding width: 400 mmworkpiece height: mmtotal power requirement: 11 kWweight of the machine ca.: 3,5 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Number of sanding units: 1 st.sanding width: 150 mmSanding height max.: 150 mmLoewer edge finishing machine MiniSpin NMachines for finishing and fine sanding ofEdges and profiles with a grinding spindlehorizontal or vertical.Motor 0,75 KWSpindle in vertical position for machining edgesPivoted spindle in horizontal position, laterallyetc. for processing longer profile bars orConjunction with a combined grinding head for grindingof edges with a grinding disc bladesGrinding head swiveling + / - 20 ° for editingoblique linesWorking height / width 150 mmmax. Diameter roller / brush

Key data: 920 mm, 2

SPECIFICATIONS: Machining width: 920 mm I Grinding roller: 11 kW II Grinding Shoe: 7.5 kW