We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
Manufacturer:
(Category: 206)
used
Code: 0168 Brand: STROMAB Model: ST 3000 - CE Standard Rotating pneumatic clamping machine, suitable for planks in general, squared timbers, strips for forming panels, table tops, steps for stairs and coffin - CE Standard Motorized rotation with release pedal and handy control wheel for worktable rotation Working capacity 3000 x 1200 mm Nr. 9 pneumatic front pressers ( 3 each side) Nr. 18 vertical columns with cylinder, diameter 80 mm ( 6 each side) Nr. 3 Working stations Thrust of vertical cylinder 8 bar kg 400 Daily output (8 hours) m2 263 Mechanical safety barriers Overall dimensions : mm 4800 x 2850 x 2300 Weight kg 1100
used
pressure: 100 tdistance between columns: 625 mmstroke: 150 mmtable surface area: 580x450 mmram surface: 580x340 mmhole in the table: Ø 150 mmtable height: 850 mmtool hole in ram: Ø 45 mmcolumn travel -side: 200x200 mmweight of the machine ca.: ca. 6,0 tdimensions of the machine ca.: BxTxH ca. 1300x1300x2750 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
HOT PRESS model OMC PL 90 , with diathermic oil heating second hand machine machine worked very very little excellent working conditions , like new CE compliant machine diathermic oil heating via built-in electric boiler heating power KW 9 / 18 for wood, veneer, composite materials, furniture, panels etc platen useful size mm.3000 x 1300 n.06 cylinders diam.mm.85 max. thrust Ton.90 opening mm.400 hydraulic pump motor power Hp 3 n.4 racks for table lifting guide max. thrust 2.5 kg/cm2 total installed power 21 kW volt. 380/50 net weight kgs. 4500
used
pressure: 250 tdistance between columns: 1100 mmstroke: 400 mmdayligth: 600 mmtable surface area: 1000x800 mmram surface: 1000x800 mmtable height: 950 mmtotal power requirement: 65 kWweight of the machine ca.: 25 tdimensions of the machine ca.: BxTxH 0000x0000x3900mm mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
HOT PRESS type COLOMBO REMO HPC 8 / 160 second hand WITH SOLID STEEL PLATES Heavy-duty construction Hot water heating via a electric system on the back of the machine , not any connection needed , everything is included on the machine Total Kw for heating 25 Solid steel plates size mm. 3450 x 1400 n.08 pistons diam.mm. 90 max. thrust Ton. 160 specific pressure max. kgs.5 / cm2 opening mm. 660 emergency perimeter rope overall dimensions cm. 4500 x 2000 x 2700 H weight kgs. 8500
used
pressure: 250 tdistance between columns: 850 mmstroke: 500 mmdayligth: 800 mmtable surface area: 800x800 mmram surface: 800x800 mmweight of the machine ca.: 12 tdimensions of the machine ca.: BxTxH 1600x1600x3400 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
HOT PRESS model SIMI 4LP second hand machine plates useful size mm. 2500 x 1300 n.04 pistons diam.mm. 80 max. thrust Ton. 60 specific pressure max. kg.2 / cm2 opening mm. 320 hot water plates heating via wood boiler (optional) weight kgs. 3000
used
pressure: 25 tdistance between columns: 800 mmstroke: 100 mmdayligth: 450 mmtable surface area: 750x750 mmweight of the machine ca.: 3 tdimensions of the machine ca.: 1500x1500x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
AUTOMATIC BRIQUETTING machine type COMAFER DINAMIC 85N second hand machine volt. 380/50 CE mark : Yes briquett diameter mm. 60 production from 40 kg. to 85 kg. / hour motor power Hp 7,5 net weigth kgs. 850
used
pressure: 100 tthroat: 275 mmstroke: 150 mmtable surface area: 860x550 mmram surface: 600x400 mmtable height: 810 mmtool hole in ram: Ø 50 mmdayligth: max. 475 mmweight of the machine ca.: 7 tdimensions of the machine ca.: BxTxH 2000x2500x3300 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
POR Super Oscar 27.5 kW briquette press – Italian production – year of production 2007 – sleeve and oil cooling – DTR TECHNICAL PARAMETERS: Ø briquette 80 mm max. briquette length 80 mm capacity 350 kg/h engine power 18.5kW+7.5kw+1.5kw = 27.5 kW hydraulic crush 1400 kg/cm2 max. working force 150 bar oil capacity 600 l tank diameter Ø 1200 mm tank height 90 cm dimensions (length/width/height) 2500 x 1900 x 1800mm net weight 2400 kg
used
pressure: 250 tdistance between columns: 900 mmstroke: 300 mmtable surface area: 850x900 mmram surface: 800x880 mmstroke: 300 mmtable height: 1050 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
HYDRAULIC PRESS with hot platens model MANNI PMC 90/36 second hand machine for wood, veneer, composite materials, furniture, panels etc platen useful size mm.3000 x 1300 n.06 cylinders diam.mm.70 max. thrust Ton.90 opening mm.430 hydraulic pump motor power Hp 2 hot water plates heating via wood boiler weight kgs. 3800 volt. 380/50
used
pressure: 200 tpassage width: 2122 mmtable surface area: 2100 x 1400 mmtotal power requirement: 60 kWweight of the machine ca.: 35 tdimensions of the machine ca.: mPress/punch with injection molding unit200 ton punch upstroke press with injection molding machine (400to)Additional guard locking via 4 power strokesManufacturer: R+S TechnikYear of construction: 2013 / rebuild 2016Mains voltage/frequency: 400V/50Hz 3~(N/PEConnected load: 60KWWeight about 35000kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Wood pelletizing plant, KAHL pellet press used the complex includes: Pellet press AMANDUS KAHL Matrice diameter approx. 1000 mm Pallet diameter approx. Ø 8 mm 5 Koller approx. Ø 340 x 130 mm Motor power 160 kW an auxiliary motor is damaged, but can be replaced by us Dimensions approx. 1600 x 1800 x 3000 mm + motor Weight approx. 8000 kg Conditioner / Dosing and Mixing Screw Diameter approx. Ø 400 mm 5.5 kW Dimensions approx. 3100 x 900 x 800 mm Single shaft paddle mixer Dimensions approx. 3300 x 1600 x 2000 mm + gear motor Pellet coolers Dimensions approx. 2300 x 2300 x 3000 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.
used
Workpiece dimensions: 2.500 x 1.300 x 500 mmSpecific pressure: 0,9 kg/cm²total power requirement: 25 kwmax. temperature: 140 Grad: 100 m³/hWeight: 1.550 kgDimensions (L/W/H): 3.330 x 1.860 x 1.950 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
I sell a press for adhesive wood gluing LISY DVORAK TH6, built in 2008. Material size 2600 X 1050 x 50mm 6 work surfaces, manual rotazion. 6 pcs hydraulic top pressures per area / pump 1.1KW 6 pcs manual pressures per area Self-weight 1350kg. Very good condition. Available the same.
new
Working width: 4000 mmWorking height: 2600 mmNumber of cylinders: 6 St.weight: 2000 kgDimensions (L/W/H): 5550x1300x3000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Hydraulic glue press with heating base, infinitely variable temperature setting, stuffenlose setting of the adhesive holding time, Power: 5 kW, 380 v 50 Hz; Two-hand operation.
new
Working width: 3500 mmWorking height: 2300 mmNumber of cylinders: 4 St.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Veneer press Total baling area L 3000 mm x W 1250 mm Opening height between the pressing surface 450 mm divided into 3 faces, each 1000 mm x 1250 mm the surfaces can be pulled out to the front without heating hydraulic pressure Good operational condition
new
Working width: 3500 mmWorking height: 2300 mmNumber of cylinders: 4 St.Stable frame welded construction of thick-walledSpecial hollow profiles , sliding table and pressure beam with50 mm hole pattern .On the left side continuous abutment for grouting the wide ,lower abutment in 2 levels.Vertical pressing cylinder on specialty bar with one-quick adjustment with weight compensation in the 50 mm hole patternadjustable in height. Long sliding table ensure thecontinuous recording of high jacking forces .Fast, smooth width adjustment with ball bearingCarriage with central fixation in 50 mm hole pattern.Upper horizontal press cylinder infinitely adjustable in height andequipped with counterbalance .Lower horizontal pressing cylinders with bore fortwo abutments levels without weight compensation .Abutment and pressure plate depth 100 mmMachine controlled electro -hydraulic with 2 pieces vertical ...
used
POR Super Oscar briquetting machine – after technical review – Italian production – year of production 2010 – sleeve and oil cooling – Odometer Reading 1659.10 mth TECHNICAL PARAMETERS: Briquette diameter 80 mm .max. Briquette Length 80 mm capacity 350 kg/h engine power 27.5 kW hydraulic crushing 1400 kg/cm2 .max. Operating Force 150 bar oil capacity 600 liters hopper diameter Ø 1200 mm container height 90 cm dimensions (length/width/height) 2500 x 1900 x 1800mm net weight 2400 kg Super Oscar PLUS is equipped with an enlarged feed drawer and specially hardened sleeves. The increased hardness of the sleeves has a positive effect on their service life, especially when we want to briquette various raw materials
new
Working width: 3500 mmWorking height: 2650 mmNumber of cylinders: nach Wahl St.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
We are offering for sale a used high-frequency press from the well-known brand ITALPRESSE, model P/259, manufactured in 1997. Below are the detailed technical specifications and features of the machine: Technical Specifications: Loading Belt: Usable dimensions: 2500x1900 mm Travel speed: 22 m/min Controlled by motor reducer: 1.1 kW Panel movement synchronized with the transport belt in the press Photocell for load control Automatic Press "P/354": Closed frame pantograph structure Table dimensions: 2500x1900 mm Number of tables: 2 Number of sections: 1 Cylinder stroke and section clearance: 140 mm Tables made of drilled solid steel: 70/90 mm Table movement from top to bottom Table heating with diathermic oil boiler: 54 kW Pressing cylinders: 9 pcs (Φ 100) Motion cylinders: 4 pcs (Φ 35) Hydraulic group power: 4 kW Pressure control manometer Automatic pressure ...
new
Working width: 120 mmWorking height: 1200 mm: 6000 mmNumber of cylinders: 12 St.1 pcs Laminating type SLV - H - 6.0 - 1.2 - 120 - 6V - IISpecifications- Working dimensions: Length: 6000 mm Height: 1200 mm Verleimdicke: 40 - 120 mm- Number of cylinder pressure: 12- Cylinder type: Ø 63 x 120 mm- Max. Force per cylinder pressure: 50 kN- Specifischer pressure: 7.4 kg / cm2- Number of hold: 6- Cylinder type: Ø 40 x 150 mm- Max. Force per hold-down: 20 kN- Number of section: 3- Max pressure: 160 bar.- Power: 3.0 kW- Pump flow: 10 l / min- Each impression cylinder and the hold-separate absperbar- Manual control with (Italian) hydraulic valves- Equal pressure in all sections- Parkiplatz for the (2x3) holding-down device to each side of the press- The dismantling pressing bar, 2 pcs, each 3 m long(. According to Manufacturer SpecificationsThe data for this ad was created with ModulMWS ...
used
Working Sizes: 1300 x 3500 mm
new
Working width: 3500 mmWorking height: 2300 mmNumber of cylinders: 4 St.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Working Sizes: 1300 x 3500 mm
used
pressure: 250 tdistance between columns: 600 mmstroke: - mmtotal power requirement: 22 kWweight of the machine ca.: 9 tdimensions of the machine ca.: 2 x 2 x 3,2 mNo. 3421Mould press 2500 / 700 kNSingle stroke 2-handSingle stroke foot switchAutomatic continuous run set-up and tippingTable 500 x 500Working range: Pressure capacity 250 tonnesDrive: ^22The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.