tornos 13 ca used for sale

sheet width: siehe TD mm plate thickness: siehe TD mm distance between columns: siehe TD mm pre-bending: siehe TD total power requirement: 3 kW weight of the machine ca.: 1,06 t dimensions of the machine ca.: 1260 x 1350 x 1900 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

The ZAKMET FIRECUT CNC 1325 13000 X 2500 gas plasma cutter was produced in 2011. The machine is equipped with Hypertherm EDGE'Pro digital control. The burner's working area is 13,000 mm long and 2,500 mm wide. The running elements of the cutter are lubricated with the Memolub 3.0 central lubrication system. Technical data of the plasma burner: - machine working area (L x W x H): 13,000 x 2,500 mm (additionally 700 mm) x 200 mm - maximum table load: 15 kN / m2 - machine supply voltage: 3x400V AC 50 Hz - central lubrication: Memolub 3.0 - minimum temperature of the working environment: +5 degrees C - maximum temperature of the working environment: +60 degrees C - machine dimensions (L x W x H): 14500 x 5500 x 2000 mm Plasma cutter equipment: - CNC control: Hypertherm EdgePro - ventilated section table: 1550 x 2600 mm - 9 segments - gas burner: type MS 3452 \ 250-PM (x2) - ...

The CE100 series is an electrically driven high-pressure machine for a pressure of 300 to 2000 bar and a volume flow of 21 to 135 l/min. The frame consists of hot-dip galvanized sheet metal moldings and stainless steel side frames. Four rubber feet ensure secure positioning. The lifting eyelet makes it easier to transport the machine. Similar but no Dynajet, Falch, Hammelmann, Kamat, Kärcher, Oertzen, Uraca, Woma, etc. Available models: ----- 50 Hz -bar-l/min. CE100-300-135 CE100-500-80 CE100-1000-42 CE100-1400-28 CE100-2050-21 60 Hz and others see data sheet and on request. General Specifications: ----- Power of the drive motor: 75 kW (50Hz) / 90 kW (60Hz) Volts: 400V (50Hz) - 440V (60Hz) Amp: 81A (50Hz) - 108A (60Hz) Dimensions: 1800 mm x 1050 mm x 1400 mm Weight: 2000 kg Includes standard accessories.

The FORNI INDUSTRIALI FIBEX COMBI 6GX-10.130-7110.2E.270 brazing furnace was built by the Italian company Forni Industriali Heat Treating Plants in 2007. The furnace is used for soldering steel elements with solder paste at temperatures up to 1120 degrees Celsius. At the entrance and exit of the furnace, two pairs of gas burners (so-called safety pilots) are installed to prevent the escape of the protective atmosphere outside the furnace. Electric heaters powered by thyristor temperature regulators are responsible for the proper temperature in the furnace. The belt furnace has a conveyor speed adjustment in the range from 0 to 500 mm / min, and the working length of the soldering zone is 7100 mm. The furnace for brazing steel elements was modernized in 2021 - the thermal insulation and the cooling module for sections 1 and 2 were replaced. The cost of the modernization was 70,000 Euro.  ...

3D CNC Router T-Rex 1215 / Technical Data : Equipment / product data CNC-milling machine type High-Z/TRex series: Drive: 3 brushless brand stepping engines with 4,5 ampere. Possibility of sliding through long and up to 120mm high materials, no belt drive at the ende of the X axis! Linear guide on all exis by HIWIN / THK ! Multiple ball-bearing ball-screw spindle on all axes, proprietary brand! Rapid traverse max. ca. 12.000 mm/min Operating speed max. ca. 8.000 mm/min Technical definition X/Y : 0,005mm (1/10 Schritt); Z: 0,0025mm Backlash maximal ca. +/- 10µm (0,010 mm) Repeat accuracy: ca. 0,01 mm Clampin surface of grooven panel / T-slot table 1860 x 1340 mm Travels: X=1500mm; Y=1200mm; Z= 130 mm Non-contact reed sensors / reference switches / limit switches on all axes Double secured emergency-stop button Energy chains for a clean cable routing Total dimensions wi ...

We offer you a new shelf for sale here. Particularities: - Height of the shelves can be individually adjusted - Floors can be hung at an angle (see picture material) - Castors for flexible warehousing - All castors equipped with parking brakes, thus enabling storage on inclined surfaces - Floor frame can be folded up, making room for a Euro pallet - Material surface: high-quality chrome-plated - Suitable for different industries - Easy and uncomplicated installation Technical data and further information: 01x shelf, new composed of: Total height: approx. 1,587 mm Total depth: approx. 855 mm Total width: approx. 1,310 mm Included in delivery are: 01x Floor frame, new Width: approx. 1,310 mm Depth: approx. 855 mm 01x rear wall, new incl. stabilization hooks 04x locking rollers, new incl. Allen key for installation 02x shelves, new Depth: approx. 3 ...

Punching machine Trumpf TruMatic TC3000-1300 FMC Year of construction 2004 87500 hours (03.2021) In this case, the configuration : TruMatic TC3000-1300 FMC Year of construction 2004 Working range : 2550 x 1280 mm Standard: • Sturdy C-frame • Coordinate guidance with integrated linear magazine, 21 seats for tools and clamps • 2 clamps • Drives: Maintenance-free digital three-phase servo motors • Punching head: hydraulic system with closed control loop, hydraulic mono tool holder, 360° rotation for all Tools, automatic tool length compensation, programmable scraper movement • Programmable hold-down • Tool spray lubrication • Punch butt suction • Partial slide 500 x 500 mm • Control Bosch PNC-P, activity-oriented user interface, Online Help, Diagnostics, 3.5" Floppy Drive, RJ45 Network Connection • Graphics programming ToPs 2000 • ToP ...

Laska W 130-1 automatic grinder, 130 mm, hopper capacity 42 Liters, control via push buttons. You are very welcome to test the machine in our facility in Koblenz, Germany.

K+G Wetter Mixer-Angle-Grinder E 130 mm type 279 with loading device, capacity of hopper (with hopper attachment) 245 l. You are very welcome to test the machine in our facility in Koblenz, Germany.

Cold water high-pressure cleaner Welcome to the innovative and compact me-Class! The DYNAJET 280me with up to 280 bar Working pressure convinces in addition to its performance above all by its compact Dimensions and high mobility. This makes the versatile high-pressure cleaner one of the All-rounders in our offer. Construction Robust, powder-coated steel frame for optimum machine protection and long service life 1-axle chassis with pneumatic tyres for easy manoeuvring on site Flexibility and support due to perfect center of gravity High durability due to screw connections made of stainless material Splash-resistant (IP54) control cabinet for versatile and smooth use Operating hours counter for optimal post-calculation Drive Manual star/triangle start to protect the power grid Compact and robust industrial electric motor for long service life with maximum running times ...

Dosing scale with precision spiral screw feeder in stainless steel version, with pre-container and weighing frame in frame, trough dimensions: 540 mm long x 370 mm wide x 320 mm high, with large loosening spiral in the trough, drive 0.47 kW via timing belt and Reduction gearbox, discharge pipe diameter: 50 mm.

with 36 rinsing stations running direction: left-to-right

We offer you here a second choice half-timbered brace of the manufacturer SSI Schäfer for sale. Technical data for the truss strut: Shelving system: SSI Schäfer Type: PR 600 Included in delivery are: 01x half-timbered strut, SECOND choice Material color: sendzimir galvanized Total length: approx. 1,304.4 mm Center-center hole: approx. 1,264.4 mm Profile dimensions: C 40 x 30 x 8 mm Diameter hole: approx. 11 mm Material thickness: approx. 1.25 mm General information about the article: This item is offered for pickup only. Any further desired transport or dispatch of this article is associated with additional costs, which can be requested separately from us depending on the place of delivery or scope of delivery.

Laska angle grinder WW 130, 130 mm, 1-speed grinder, frozen meat version, all stainless steel, ergonomic control, saftey cover for cutting set hinged and electrically interlocked, saftey grid for hopper. The machine is immediately available and can be tested in Koblenz, Germany.

I sell a stacking / destacking system MEINERT (IMA Group) P620 E/S - 2500 / 1300 system, year of construction 2011. Stacking system One-sided steering / also suitable for pallets. Vacuum system (with pump) Rotazion head Automatic charging. Entrance table motorized roller system Exit table on the floor with lifting mechanism motorized roller system Exit table front roller system Entry of feeding roller stazion for stilted material. Security fence fully complete ! Working capacity Approx. 16 cycles / min Plate height 10 - 50mm Min. plate dimensions 250 x 320 mm plate dimensions 1300 x 3000 mm Combined area L.10200mm x W.8700mm Combined power 45kW Year of construction 2011 Available the same. Ready for use, possible to check. With CE certificate and full document.

Graule ZS 135N Cutting and mitre saws Motor 400 V / 2.0 kW Speed 3800 RPM Cutting length 440 mm (at 90 °) Cutting height 135 mm (at 90 °) Miter range: horizontal 45 °-90 °-25 ° Guide area: vertical 90 °-45 ° (left) Saw blade ø 350 mm Dust nozzle 100 mm Weight 100 kg

Seydelmann automatic grinder AE 130, 130 mm hole plate diameter, almost completely made of solid stainless steel, 2-speed working worm, 2-speed feeding worm of stainless steel, conical and extra wide, rectangular to the working worm, approx. 14/18 kW, feeding motor approx. 1,8 kW, separately switchable, hopper capacity approx. 130 litres, with interlocked safety grid, worm, worm housing and closing nut completely stainless. The machine will be available soon and can be tested like in Koblenz, Germany.

Abegg to fan and the fan with fans Ziehl. noch nie benutzt NEW

Model: M130 The machine is massive, made entirely of stainless steel. Equipped with a protective cover on the neck and on the receiving hopper. The neck is massive, cast with spiral grooves. The tool set of the machine consists of a large working auger, a massive nut, knives with a cast plate Robot C4 - 2 pcs., kidneys - 2 pcs., grids of sizes: 3,4,5,5,7-8, 10 and 13 mm. , distance sleeve - 2 pcs., Mercedes - fixing sleeve The machine is extremely reliable. The electrical components and bearings used in the machine are of leading global brands. Powerful motor – 8 kW, built into the machine. There is an additional lever for automatic extraction and easy disassembly of the tools. Technical data: - neck diameter: 130 mm. – capacity of the receiving hopper 65 l. – 2 auger speeds – 5 cutting tools The machine is patented and has a CE ...

Seydelmann ME 130, mixing grinder, hole plate diameter 130mm, Unger cutting system, working worm 2 speeds, 1 mixing speed, safety grid. You are very welcome to test the machine in our facility in Koblenz, Germany.

Plywood Press, manufactured by Siempelkamp, working sizes 2500 x 1300, 10 floors

Can make meatballs and burgers up to 130mm in diameter. and height up to 30 mm; – The height can be adjusted; – Equipped with a speed controller; – Limit switch for more tape security; – Motor: 0.3 kW – Single-phase motor – Hopper capacity 24 l. Standard shapes: Round burgers with diameter: 22 mm. 32 mm. 40 mm. 65 mm. 100 mm. 115 mm. 130 mm. Round meatballs with diameter: 22 mm. 32 mm. 40 mm. 65 mm. Depending on the chosen thickness, a different weight of the final product can be achieved with one mold. Accessories: As standard, the machine comes with one mold. As an option, you can also order: Round burgers with a diameter of: 22 mm. 32 mm. 40 mm. 65 mm. 100 mm. 115 mm. 130 mm. Round meatballs with diameter: 22 mm. 32 mm. 40 mm. 65 mm.

SMG DS 315-1500/1300 CNC hydraulic press was manufactured in 1984 in Germany. The machine, consisting of two interconnected stations, is used for pressing metal workpieces in manual, semi-automatic and automatic mode with a pressing force of up to 315 tonnes. All the machine’s machining parameters are set using a CNC control with a full-colour, touchscreen display. The press is equipped with a hydraulic and pneumatic sheet metal feeder, servo drives for feed rollers to set a very precise stroke of up to 0.1 mm, safety cages and workpiece feed and drop control sensors. The SMG 315 T machine underwent a complete overhaul in 2007, during which components such as pumps and safety installations were replaced. Technical data of the SMG DS 315-1500/1300 press - maximum press force: 315 t - working table dimensions (L x W): 1500 x 1300 mm - upper machine point (from the table): 750 mm ...

HACO OMATIC 130 DTRH punching machine was built in 2014 in Belgium. The machine is used to punch various size shapes and holes in workpieces weighing up to 150 kg and having a maximum thickness of 6.5, a width of 1500 mm and a length of 4000 mm. The machine operator manually operates the punching machine by loading the workpiece on the working table and changing the punching tools using a special device offered in the price of the machine. The punching process takes place on the brush table of the punching machine, which significantly reduces noise levels and adequately protects the sheet metal surfaces against various types of scratches and nicks. Depending on the choiceed mode, the machine performs between 1,000 and 1,500 punches per minute with a press force of 30 tonnes. The equipment includes amongst others a TPC 69C Graphics CNC controller for graphical programming of the desire ...

Sell granulator for plastic strands of extrusion. 7,5 kW power. Sale, clearance there. If it works, I don't know, therefore the reasonable sale price.

Synchronous motor, MDD115C-N-015-N2M-130GB2, R911262637, Rexroth, new Special price If you have a VAT number, we will gladly issue you an invoice without VAT. Mint condition in original packaging! The part was purchased from a spare parts warehouse of a company, was there for a long time in stock but never in operation, is in a completely mint condition and in its original packaging. - Permanent magnet motor - max 75 Nm - max. 64 A - 55 kg 6 months warranty We give you 6 months warranty for these goods from the date of invoice. In case of any defect, which is not the fault of the seller, the goods can be returned. We will refund the buyer only the product price paid to us. Updating in case of digital components is excluded. Also excluded is liability for direct and indirect consequential damages. Our terms and conditions apply, see our website. Austrian law applies wit ...

Sychron motor with ball screw, MDD115C-N-015-N2M-130GB2, Rexroth, mint condition Special price High quality parts from a major car manufacturer! If you have a VAT number, we will gladly issue you an invoice without VAT. As good as new with traces of storage! The assembled linear actuator comes from a spare parts store of a mechanical processing. Year of manufacture 2008. The parts are as good as new, but have minor storage traces. Technical data: 1 complete linear actuator, 119x29x20cm, ca. 150kg, consisting of: - 1 pc Sychnron motor MDD115C-N-015-N2M-130GB2, R911262637, from Rexroth, permanent magnet motor, max. 75Nm, 1500rpm, 55kg, - 1 pc Motor bell with bearing for the ball screw drive and 2 clamping sets for fastening the ball screw drive to the motor, Grob, - 1 pc ball screw drive 1516.319/10.50.353.591 T3, D50mm, total length of the screw approx. 591mm, thread  ...

Sychron motor with ball screw, MDD115C-N-015-N2M-130GB0, Rexroth, mint condition Special price ! High quality parts from a major car manufacturer! If you have a VAT number, we will gladly issue an invoice without VAT As good as new with small traces of storage! The assembled linear actuator comes from a spare parts warehouse of a mechanical processing. Year of manufacture 2011. The parts are as good as new, but have minor traces of storage. Technical data: 1 complete linear actuator,181x29x20cm, ca. 150kg, consisting of: - 1 pc Sychnron motor MDD115C-N-015-N2M-130GB0, R911262636, from Rexroth, permanent magnet motor, max. 75Nm, 1500rpm, 52kg, - 1 pc Motor bell with bearing for the ball screw drive and 2 clamping sets for fastening the ball screw drive to the motor, Grob, - 1 pc ball screw drive 1516.339/10.63.1033.1276 P3, D63mm, total length of the screw approx. 1276mm ...

1 factory-tested, well-preserved single-girder crane Load approx. 6,300 kg Wingspan approx. 19.134 mm Hook path about 8.000 mm Fabrikat ABUS/DEMAG Year of production/workshop test 1974/2016 Crane equipped with DEMAG monorail trolley, freely movable floor control Working speeds: Hoist 1.0/10.0 m / min Katz LG 5.0/20,0 m / min Crane chassis 10.0/40.0 m / min

Sychron motor with ball screw, MDD115C-N-015-N2M-130GB0, Rexroth, mint condition Special price ! High quality parts from a major car manufacturer! If you have a VAT number, we will gladly issue an invoice without VAT As good as new with minor traces of storage! The assembled linear actuator comes from a spare parts warehouse of a mechanical processing. Year of manufacture 2011. The parts are as good as new, but have minor traces of storage. Technical data: 1 complete linear actuator, 181x29x20cm, ca. 150kg, consisting of: - 1 pc Sychnron motor MDD115C-N-015-N2M-130GB0, R911262636, from Rexroth, permanent magnet motor, max. 75Nm, 1500rpm, 52kg, - 1 pc Motor bell with bearing for the ball screw drive and 2 clamping sets for fastening the ball screw drive to the motor, Grob, - 1 pc. ball screw 1516.339/10.63.1033.1276 P3, Fa. Steinmeyer, D63mm, total length of the screw ap ...

Sychron motor with ball screw, MDD115C-N-015-N2M-130GB2, Rexroth, mint condition Special price High quality parts from a major car manufacturer! If you have a VAT number, we will gladly issue you an invoice without VAT. As good as new with traces of storage! The assembled linear actuator comes from a spare parts store of a mechanical processing. Year of manufacture 2011. The parts are as good as new, but have minor storage traces. Technical data: 1 complete linear actuator, 169x29x20cm, ca. 150kg, consisting of: - 1 pc Sychnron motor MDD115C-N-015-N2M-130GB2, R911262637, from Rexroth, permanent magnet motor, max. 75Nm, 1500rpm, 55kg, - 1 pc Motor bell with bearing for the ball screw drive and 2 clamping sets for fastening the ball screw drive to the motor, Grob, - 1 pc ball screw drive 1516.310/10.63.848.1091 P3 D63mm, total length of the screw approx. 1090mm, thread ...

Sychron motor with ball screw, MDD112D-N-030-N2M-130GB2, Rexroth, mint condition Special price High quality parts from a major car manufacturer! If you have a VAT number, we will gladly issue you an invoice without VAT. As good as new with traces of storage! The assembled linear actuator comes from a spare parts store of a mechanical processing. Year of manufacture 2011. The parts are as good as new, but have minor storage traces. Technical data: 1 complete linear actuator, 185x26x28cm, ca. 250kg, consisting of: - 1 pc Sychnron motor MDD112D-N-030-N2M-130GB2, R911260224, from Rexroth, permanent magnet motor, max. 75Nm, 3000rpm, 62kg, - 1 pc Motor bell with bearing for the ball screw drive and 2 clamping sets for fastening the ball screw drive to the motor, Grob, - 1 pc ball screw drive 1516.78/10.80.910.1189 P3 D80mm, total length of the screw approx. 1189mm, thread  ...

Geschliffener Präzisions Kugelgewindetrieb, D50 x 10/6, 1344 mm, Eisenmann, neu Neuwertig in Originalverpackung! Der hochqualitative Teil stammt aus einem Ersatzteillager einer mechanischen Bearbeitung eines grossen Automobilherstellers, ist völlig neuwertig und in der Originalverpackung. Achtung: Wir haben viele, lagernde, hochqualitative Kugelgewindetriebe in verschiedenen Ausführungen in den Durchmessern 32, 40, 50, 63 und 83mm. Schauen Sie auf unsere Webseite der IPV GmbH. Kugelgewindetrieb, Kugelgewindespindel, Kugelrollenspindel, Type 20110180, D50 x 10/6 mm, 1344 mm, Z-Nr. 105367.1335.01, Fa. Eisenmann Kugelgewindedurchmesser 50 mm, Steigung 10 mm, Gewindelänge 1082 mm Länge der Kugelgewindemutter 161 mm, Max. Gesamthub 921 mm, Gesamtlänge der Spindel 1344 mm Durchmesser für Kupplung mit Motor 32 mm Durchmesser Lagersitz A 35 mm, Durchmesser Lagersitz B 3 ...

l 90 kw POWER 1350 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 500 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control of the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 90 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw

SERON 1315 EXPERT CNC milling machine built in Poland in 2017 is new and has never been used. The machine designed and manufactured with attention to the smallest details, is used for precision machining of a wide range of materials such as mild metals, plastics, carbon, wood, wood-like panels and glass. All vibrations and deformations during the milling process are eliminated by the high-quality ribbed steel construction with a T-slot table made of aluminium profiles, with a length of 1500 mm and a width of 1300 mm. The workspace is additionally equipped with a special PVC overlay to protect the table cover while cutting the workpieces through. At the end of the table there is a six-position linear magazine with an automatic tool correction sensor. The 1315 EXPERT machine axes are driven by highly dynamic and precise brushless AC servo drives with back pressure, equipped with serv ...

Year of manufacture 2001 generator multi pulse - 70 amp + 100 amp booster Control Mitsubishi 32 bit - CNC travel (X, Y, Z) 900 x 1,780 x 550 mm Bowl (W x D x H) 1300 x 2200 x 730 mm workpiece clamping table (B x T) 1150 x 2050 mm accessories 13-fach pick-up linear changer, CO2 fire extinguishing status completely overhauled

CATALOG NO. 6887 TECHNICAL SPECIFICATIONS - track width 340mm - shaft width 350mm - max disc diameter 400mm - blade bore diameter 70mm - max cutting height 130mm in advance: - 2 rows of ratchets - 2 smooth pressure shafts, slip shafts -Pressure - shaft with saws - 2 smooth pressure shafts, slip shafts from below: -Guide -Triggers -caterpillar - smooth regulation of feed speed - electric body lifting - main engine 37kW - feed motor 1,5kW - central lubrication - table top dimension 1930x840mm - dimensions length / width / height 2250x1650x1600mm - weight 2900kg – Italian production – used multi-saw – very good condition Net price: 49900 PLN Price without tax: 11213 EUR depending on the price 4.45 EUR (Prices may fluctuate with higher fluctuations)

TRUMPF TruPunch 3000-1300 (S11) punching machine was built in Germany in 2013. The reliable machine with extensive equipment and modern components offers its user unparalleled precision and accuracy in machining both thick and thin sheet metal. In addition to standard punching and marking, the punching machine also allows fast grooving, surface embossing, forming and chipless threading in stainless steel, structural steel and aluminium. On the machine’s sturdy and welded C” shaped structure, sits a specially designed brush table with integrated balls, designed to facilitate the loading and unloading of workpieces. The use of this type of table prevents scratches and nicks from appearing on the surface of the sheet, which results in a significant increase in the quality of the machining. During the entire production process, the sheet is held rigidly by hydraulic clamps fixed to th ...

reverse soil tiller - 130 cm working width, right offset machine, three-point hitch cat. I, movable grilles roller 150 cm with scraper, 8 rows of blades, possible working depth 14 cm. Another reverse soil tiller 155 cm and soil tiller in stock!

TIMESAVERS 41 SERIE 1350 WRD deburring machine was manufactured in 2004 in the Netherlands. The wide belt deburring machine is used in both small and large production facilities for precision smoothing of sharp edges and finishing work. The machine provides high performance and reliability throughout its service life. The surface machining of workpieces made from e.g. steel, aluminium and titanium is performed wet by a grinding system comprising a reliable abrasive belt and brush unit. The workpiece is dried at the end of the machining process so that the parts leaving the machine are dry and free of contamination. The deburring machine has an integrated paper belt filter into which the used coolant is transferred at the end of the process in order to separate the swarf and allow the coolant to be reused. Technical specifications of the TIMESAVERS 41 SERIE 1350 WRD deburring machin ...

Air-operated airless pump on pump trolley The T2001 piston pumps are robustly designed air-driven airless pumps designed for pumping, decanting and painting with multiple guns. The parts that come into contact with the material are made of stainless steel, carbide, PTFE or PE.  An ATEX approval for use in potentially explosive atmospheres completes the picture and makes the pumps versatile. Below you will find the advantages at a glance: - Minimal pulsation for uniform material flow during conveying and spraying - Versatile use due to stainless steel, carbide, PTFE or PE in the material area - Suitable for liquid solvents and water-based materials - Easy commissioning due to self-priming system - Maintenance-free device, no lubrication required - Integrated safety valve in accordance with accident prevention regulations - Mobile versions on pump trolleys - ATEX approval E ...

The HERBOLD plastcompactor is a system for the agglomeration of films, fibres, chips, dust and flakes. Poorly free-flowing waste is turned into an agglomerate with a high bulk density and good flowability, which can therefore be applied directly to extruders and injection moulding machines. The plant for sale has a main motor with 110 kw drive power and a throughput of 600 to 2000 kg/h depending on the feed material. All thermoplastics can be processed, even sensitive materials such as PET, PA, and bioplastics can be agglomerated without thermal damage or discoloration. The system consists of the feeding device with silo, the compactor, a re-cutting mill with sifting and fine material return On request, a pre-shredding can be offered that is adapted to the task Tests can be carried out in our technical center for suitability tests and sampling. We are the manufacturer of this s ...

Key data: 1320 KW, 1650 kVA

ENGINE: Cummins KTA50-GS8 FREQUENCY (HZ): 50 VOLTAGE (V): 400 GENERATOR POWER: 1650(kVA) / 1320(kW) ENGINE POWER: 1287(kW) CYLINDERS: 16 STARTING: ELECTRIC CONTROL SYSTEM: SELF-CONTROL FUEL TYPE: DIESEL COOLING: WATER-COOLED WEIGHT: 1100kg DIMENSIONS L/W/HEIGHT (MM): 680022503200 The engines are new, complete including control, diesel tank, exhaust and batteries. Network monitoring, grid feed-in Soundproofed Immediately ready for use. Control: Deep Sea Electronics (DSE) / ComAp Alternator: Leroy-Somer / Stamford Additional: Automatic Transfer Switch (ATS) 63A/100A ABB & Schneider Disconnectors GenCloud Connect with a phone or computer Single-phase valve 50°C-55°C Radiator External Diesel Tank Lubricating Oil Heater Water Heating Dispatch: Worldwide transport including unloading is possible for an extra charge To be able to quote an exact freight pri ...

Max sheet size 1300 x 1100 mm min. Sheet size 350 x 350 mm Precision +-1.5 mm Speed 6,000 sheets / hour Power 12 kW Length 12,5 m Weight 6.8 t

ALMiG Gear 132 Screw Compressor The screw compressors of the GEAR series are particularly suitable for very high compressed air requirements.  The maintenance- and service-friendly drive concept of the GEAR compressors includes a robust drive motor with strong power reserves. The highly efficient gearbox works with minimal slip, high operational reliability, is almost loss-free with an efficiency > 98% and protects the drive. In addition, highly efficient separation of the coolant enables a minimum residual oil content of only 2–3 mg/m³. Due to the encapsulated design of the gearbox set, these systems are suitable for use under the toughest operating conditions. Ideal for very high compressed air requirements Robust drive unit with strong power reserves Virtually loss-free concept with efficiency > 98% Maintenance- and service-friendly drive concept  ALMiG Gear 132  Yea ...