We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
complete set: DEMAG 50T ERGOTECH COMPACT 50-200 1999 (-) ENGEL 75T ES330/75 VICTORY 2001 (working hours 81694) working good tech. condition T557211 for both machines 10 000 EUR
used
COMI RICO CCL 1900 x 900 -13T-AB thermoforming machine was manufactured in Italy in 1988. The thermoforming line, consisting of, among others, a heating station, a bulge photocell and a moulded parts conveyor, is designed for the fully automatic production of oversized parts using the thermoforming method. The COMI RICO CCL 1900 x 900 -13T-AB thermoforming machine is equipped with a gauge measuring the thickness of the platen in order to avoid accidentally taking two platens from the package at the same time. The platens, by means of transport grippers actuated by pneumatic cylinders, reach the individual work stations, i.e. the preheating station, consisting of two opposing panels, the plasticising preheating station and the forming unit. In the forming unit, the thermoforming process takes place, during which a BOTTINI GIANNI press with an upper and lower moving table peripherall ...
used
M. No.: 3284 Equipment / Additional information: (min.) material thickness: 0.65 mm (max.) material thickness: 2 mm Technical Data: Width of film, max./min. 450/350 mm Forming area max. 430 x 160 mm Drawing depth max. negative/positive 6/20 mm (on request 22 mm negative) Top heater max. 10,15 kW Driving motors 3,0 kW Total connected load at 100 % duty cycle 12,7 kW Working air pressure 6 bar Air consumption (dependent on product) max. 1250 I/min Rate of water flow max. 1,0 m3/h COMPACT AND ROBUST - giving continuous high output. Easy and ergonomical operation (e.g. take- off height 1300 mm). QUICKLY CHANGEOVER - from 30° to 90° foil feed giving maximum material utilisation for both square and round lids. Heater changeover problem-free. PRECISION - The accuracy of the form table movement is guaranteed by linear guide bearings and hardened rods. The safe ...
used
Gabler D600 Thermoformer, age 2000:- Unwind Stand Indramat Servomotor Indexing. Top & Bottom Heaters, total Capacity 73.9 kW Indramat Servomotor Forming Station Forming area: 600 x 320 mm Depth of draw neg./pos.: 40/15 mm Stacking and counting Station Counted/ Stacked Products transferred automatically to Delivery Conveyor Waste Material Winder Main Machine PLC Controller: Siemens SIMATIC S5 P3 3A Heater PLC Controller: Siemens SIMATIC S5 95U Operator Touch Pad Control Panel (OPC) : Siemens SIMATIC OP27 Machine has been refurbished in 2014, New set of Cams added during Refurbishment. Excellent Production Condition
used
Motorized Film Indexing Max. Film width 805 mm Double Heating:Top Heater 81.90 kW Lower Heater 54.60 kWGabler M92XL Thermoformer, age 2009, with Cup Mold for Ø95mm PP Cups, Sheet Sag Control Max. Form Area 765 x 436 mm Indramat Servomotor Plug Assist Max. Depth of draw 150 mm (optional 200 mm) Clamping pressure 380 kN Motor Drive Rating 81.90 kW Air Pressure 6 - 10 bar Max. dry cycle speed 52/ minGabler M92XL Thermoformer, age 2009, with Cup Mold for Ø95mm PP Cups, Bottom Platten with Tilting movement Inline Counter/ Stacker Unit Counted products delivered to delivery conveyor at 90degs. to machine direction Suitable for PS, PP, PVC, ABS, PLA, PET etc. Siemens S7 PLC Controls Siemens SIMATIC MULTI PANEL Touchpad Display Inclusive of PP Cup Mold for Ø95mm PP Cups, 22-Cavity and associated Stacking Parts
used
Material : PP, PET, HIPS // Forming Area (Vxh): 800x550
used
Material : CPET, PET, PP, HIPS, OPS, PVC // Forming Area (Vxh): 800x570
used
ILLIG PLS75B Inline Counter/ Stacker, with Hole Punch Station, age 2006 used Inline with ILLIG RDM75K ! Max. Stacking Area: 750 x 350 mm Min Height of formed product: 25 mm Max. height of Formed Product: 150 mm Min. dia. of product : Ø 40 mm Max. dia. of Product: Ø 150 mm Max. length of Product Stack: 730 mm Output rate of Product Stacks: 1200 Stacks/ hr Rotating Head to neatly remove Products from the Thermoformer Mold Inline Hole Punch Station Inline Counter Stacker Station Compressed Air: 0.2 L at 6 bar, approximately Total Drive Rating: 19 kW Electrical specifications: 400 V, 3 phase, 50Hz (N/ PE) Cross delivery conveyor for counted cups. All Motors are Indramat Servo Motors Siemens SIMATIC TOUCH LED Operator Control Panel with Touch Pad Controls Siemens S7 PLC Controls Delivers Counted Cups/ Containers at Right Angles to machine direc ...
used
Used ILLIG RDK 54 Thermoforming Line, Age 1995 Unwind Stand Indramat Servomotor Indexing Max. Film width 610 mm max. Thickness range 0.18 to 2.5 mm. Hardened Transport Rails, Double Heating, Heating Load 41.0 kW. Heaters move forwards automatically with pneumatic control Sheet Sag Control Form Area 550 x 400 mm Forming & Punching in Mold with integrated Steel Rule Die. Positive Draw 20 mm, Negative Draw 20 to 40 mm Trimming Force 50kN. Top and Lower Platens Moved by separate Indramat Servomotors Heavy duty Toggles on both upper & Lower Platen Stacking/ Counting Station Waste Material Winder Inline ILLIG RS75b Grinder with Sound Proof Housing & Controls. Suitable for PS, OPS, PP, PE, PVC etc.
used
Illig RDM 37/10 Thermoforming Line - Made in Germany - Year of construction: 1986 - Under & Top Heating - DIV - Moulding area: 475 x 250 mm max. - Film width: 495mm min / 150mm max. - Refurbished: new bearings, new bolts, new bushings & electronics, etc. - Fully functional - with many accessories - several different forming tools Produce cups, bowls and similar products with the ILLIG RDM37/10 pneumatic forming machine. The thermoformer with forming/stamping technology works reliably with precision mechanical drives and delivers high molded part quality and performance.
used
Technical specifications: Rated power, kW: 11,3 Mold area, mm: 475 x 250 Max. film width, mm: 495 Min. film width, mm: 150 Max. feed length, mm: 280 Min. feed length, mm: 50 Max. drawing depth/negative, mm: 100 Number of cycles/min.-max.: 48 Consumption of air/cycle at 6 bar: 100 Nl (net-pressurized air) Heat energy to be dissipated: with top heating ca. 10 260 KJ/h with top and bottom heating ca.: 17 715 KJ/h Special equipment: Hollow floor facility available Control cabinet: included
used
Unwind Stand Preheater ILLIG VHW 72/ 2 ILLIG RDM 70K (refurbished in 2003) Thermoformer with auto-start facility Indramat Servomotor Indexing Top & Lower heaters Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 680 x 280 mm Pneumatic Plug Assist, Max. Part height 125 mm Control Cabinet with Optimised Schleicher (PLC) Controls Auto Lubrication Pump. Inline ILLIG ÜG70B Counter/ Stacker, with delivery conveyor Inline Grinder & Blower
used
Unwind Stand Preheater ILLIG VHW 72/ 2 ILLIG RDM 70K, age 1989 Thermoformer with auto-start facility SEW Eurodrive Servomotor Indexing Max. material width 730 mm Max. Indexing length 300 mm Top & Lower heaters, total connected load top & bottom heaters 74.2 kW Drive Motor 6.93 kW Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 680 x 280 mm Hydraulic Plug Assist, Max. Part height 125 mm Hydraulic Power Pack Control Cabinet with Optimised Schleicher (PLC) Controls Encoder on Main Shaft Auto Lubrication Pump. Inline ILLIG UG70b Counter/ Stacker Delivery Conveyor for Counted/ Stacked Cups with Ejector Table
used
M. No.: 322 // Counter: 80188 hours Max. film width 700-800 mm Equipment / Additional information: The machine is constructed as follows: -Greiner stacking / Transfer device R3 (No.:00020) // Age: 1998 -ILLIG mill RS75B // Age: 1999 Control cabinets, etc. Heating from above and below Material PS and PP were processed 450 Ps // 350 Pp
used
Illig RDM75K age 1998, refurbished in 2019, with Siemens S5 PLC Controls, used only for ca. 50,000 hrs ELAU B1 Display with Touchpad controls Thermoformer with auto-start facility Indramat Servomotor Indexing Max. material width 750 mm Max. Indexing length 480 mm Top & Lower heaters, total connected load top & bottom heaters 111.3 kW Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 700 x 450 mm Hydraulic Cylinder Plug Assist with Bosch Rexroth Hydraulic Power Pack, completely Overhauled in 2019 Max. Part height 150 mm Max. Mold closing force 25,000 daN Auto Lubrication system Siemens S5 PLC Controls New original ILLIG/ RITTAL Control Cabinet Cooling System added in May-2023.
used
Material : PS – PS/PE – PE/PS/PE– PVC – PET – ABS // Forming Area (Vxh): 700x500
used
ILLIG STAL80 Trim Press, age 1988:- Technical data ILLIG STAL 80 : Punching table area max. 1000 x 510 mm Material width max. 800 mm Infeed length 20 - 400 mm Stroke height 200 mm Mold height 272 mm Part height (positive and negative) max. 100 mm Number of strokes (infinitely variable) 25 - 130 /min Trimmed Parts are stacked through the Punch Tool The Skeletal Waste is fed directly into the Grinder ILLIG RS75 Under the Trim Press Grinder, Motor 8.3 kW, age 1995
used
Thermoforming Machine Brand: Kiefel, model: 76/225F. It shapes and cuts by vacuum pieces from rolls of PPE that are previously heated in the oven. Everything goes online, fully automatic and includes all empty aurxiliars, refrigeration, mold change trolleys, etc. Forming area: 760x2250 mm max, workpiece height: 220 mm pos. max, 30 mm neg. max, upper cutting force: 30 KN, lower cutting force: 30 KN, sheet line: 1575 mm, vacuum: 500 m 3/h, cycle time: ca. 20 sec (material dependence), glue type: butyl or hot melt glue, glue application speed: mx. 400 mm/sec (depending on the contour and type of glue), applicator head control: amount of glue depending on speed, tool change time: less 5 min, measures: 25500x6000x4600 mm.
used
LEISTER TRIAC heat gun, heat gun. Embossing on the device: K.LEISTER TYPE TRIAC CH-KÄGISWIL Motor 60W 220V ~6.6A Max 1460W 12820 Made in Switzerland GS S+ Used, very well preserved with signs of wear. Includes accessories, as pictured. Two-stage Cable length 3m Machine for processing and welding plastic geomembranes, shrinking plastics, films and other applications.
used
Polytype BDM 681 Polyflex, for round cups, age 2014 only used for less than 20,000 hrs. The pre-treatment and the UV-Mandrel curing are integrated in the basic machine concept. The newly designed cup in-feed and discharge automation round off the system. The main characteristics of BDM 681 printing technology are the very high effiency, the outstanding print quality, the short change-over time as well as the excellent accessibility and ergonomics (one operator layout). Technical data: Min./max. cup height: 35 -200 mm Min./max. rim diameter: 60 - 185 mm Min./max. taper: 2 - 15° Max. print height: 145 mm Max. print length: (6 sections) 273/345 mm Max. print length: (3 sections) 418/502 mm Max. printing speed: 650 cups/min Servomotor Universal Screw Denester UV Unit with dual 6" UV-Lamps FHW 3.0 CP Corona Pretreatment with Leak Tester. The Print Heads are modern day Print Heads ...
used
Forming Area (Vxh): 640x450
used
Make WM Model FC 780E Year 2007 Condition Excellent Hours approx 29950 Delivery Date Immediately Stations Forming, Cutting and Stacking Max Tool Size 780 x 570 mm Depth of Draw 130 / 130 mm Max Material Width 810 mm Max Sheet Thickness 1.8 mm Max mould closing force 20,000 daN Forming pressure 7 bar Maximum cycles-minute 45 Total Connected Load 140 Kw Approx Total Length 11000 mm Approx Width 5000 mm Approx Height 2550 mm Approx Total Weight 11000 kg All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale
used
Make WM Model FC 780E Speedmaster Year 2010 Condition Very Good Hours approx 21500 Delivery Date Immediately Stations Forming, Cutting and Stacking Max Tool Size 780 x 570 mm Depth of Draw 130 / 130 mm Max Material Width 810 mm Max Sheet Thickness 1.8 mm Max mould closing force 20,000 daN Forming pressure 7 bar Maximum cycles-minute 45 Total Connected Load 140 Kw Approx Total Length 11000 mm Approx Width 5000 mm Approx Height 2550 mm Approx Total Weight 11000 kg All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale