spinning machine used for sale

YOM 1987. Worked not more than 10 years, one shift Grinding length 3000 mm Grinding width 1700 mm Workpiece height 1600 mm Distance between columns 1860 mm Grinding heads- 2 Table surface 3230x1600 mm Number of slots of the table 10 pcs Permissible table load with evenly distributed load 5000kg/m Weight of work-piece 15t Table travel speed 1-40m/min

Roller spreader for rear mounting, drive via a 12 volt electric motor with overload protection (8 A). Container contents 120 ltr. , cam roller with interchangeable, asymetric cams (suitable for sand, salt and shards or granules)Roll width 125 cm, stirring shaft to prevent lump and bridge formation, low-wear 10-stage scattering volume regulation by adjustable spring bottom with rubber apron. With grating for accident protection and cable remote control (start/stop). Without growers! Scattering length salt approx. 5-6 km, sand approx. 1 km (manufacturer specifications) Built in 2012, unused, technically and visually as new condition, here and there paint somewhat repelled. Other roller spreaders, also trailers, self-loaders, drive hydraulic, PTO shaft or wheel stock. Winter service technology of all kinds, also slingshot spreaders, snow shields, snow blowers, tractors and used compon ...

The machine packs in full cartons or trays. Capacity up to 80 cartons per minute. The change to the new carton format takes place from the operator panel - very quickly. Siemens S-7 control. Machine dimensions: Length: 9m Maximum width: 3.2m Height: 2.4 m. Weight: 3.5 tonnes The machine is equipped with a set of necessary spare parts for 2-3 years of operation. The machine after complete renovation in very good condition. Ready to work. We provide 12 months warranty. The condition of the machine and the level of modernity ensure many years of operation.

Nilfisk T30S Industrial Vacuum Cleaner - Used, Tested & Ready to Use - Top Condition! For sale is a powerful Nilfisk T30S industrial vacuum cleaner, ideal for workshops, production, construction and industrial applications. Specifications: • Model: T30S • Year of manufacture: 2011 • Voltage: 400 V / 3 phases • Power: 3.0 kW / 400 V, 50 Hz, 2840 rpm, 3 phases, 6.6 A, cos phi 0.90, Iso F, S1, IP55 • Container volume: approx. 100 litres • Vacuum -220 mbar, 130 m³/h Overpressure 278 mbar, 120 m³/h • Filter type: cartridge filter • Weight: approx. 103 kg • Condition: used, fully functional Scope of delivery: • Vacuum cleaner Nilfisk T30S •Hose • Original chassis Condition: The device has been tested – motor runs smoothly and powerfully. Filters and containers were cleaned. Shipping / Pickup: • Pick-up preferred (heavy equipment)  ...

Weibert FR3 Saw milling Demonstration device Format sliding table 2300mm or 2600mm Cutting height: 103mm Auslegertich kpl. Saw blade: swivel, max.315mm 3KW motors Milling: rigid 90° Milling rpm: Speeds: 1500/3500/6000/8000 rpm. Safety rails milling stop 500mm Right- and left-hand-running milling cutter WJ-400100

Double Z kneader / Sigma kneader Topos Used Double Z Kneader Topos 250 L – Sigma Kneader – - Kettle Kneader – Dough Kneader - Industrial Kneading Machine – Stainless Steel – Overhauled and Function Tested Robust stainless steel construction, powerful drive, ready for immediate use. The Topos double Z-mixer with a usable volume of 250 litres is a robust and powerful industrial machine for highly viscous mixing and kneading processes. Thanks to its solid kneading arms, it ensures even mixing of viscous media and doughs. Industrial materials such as doughs, sealants, paints, adhesives, raw ceramics or chemical mixes. The machine was designed for continuous industrial use and impresses with its stable design, durable design and easy-to-clean stainless steel design. - Make Topos, built around 1965 - Completely overhauled in 2018. Function-tested. - Easy ope ...

Flake Ice Machine / Rotary Evaporator with Silo Manufacturer: MAJA Type: RVH 1500 CO2 The flake ice generators of the MAJA RVH series can be integrated into refrigeration concepts that are designed for environmental compatibility and sustainability. Specifications: Year of Make: 2019 Ice capacity approx. 1500 kg / 24h Dimensions of the entire facility: width 175 cm / depth 130 cm / height 230 cm Weight approx. 450 kg Electrical connection 3AC/50Hz/400V/PE0.28 kW Control: Maja Touch Panel (optional) Refrigerant required: R744 Function checked / machine ready for immediate use! Condition and accessories see original pictures! If you have any questions, email or call.

Butter Forming & Wrapping Machine Manufacturer: Trepko Type: XPG40 Working hours: 0 since reconditioned Capacity: 40... 90 Pa./min, infinitely adjustable Products: Butter, Margarine etc Choose Format: 250 gr. (100x70x35 mm) Folding: bottom folding Packing material: aluminium foil, parchment paper Dosing: volume doser from 100 .. 300 gr. Dosing precision: +/- 1 % Energy: 380 V/50 Hz; 2,2 KW Weight: 1.600 k

The SIP Sirius 7 is a high-precision fixed-bridge Coordinate Measuring Machine (CMM) designed for dimensional inspection and quality control in manufacturing environments. Sirius 7 is known for its robust construction and hydrostatic bearing system, ensuring smooth and accurate measurements. Key Specifications • Measuring Range: 1,000 mm × 1,000 mm × 800 mm (X × Y × Z) • Accuracy: ±4 µm (micrometers) • Repeatability: ±2 µm • Guide System: Hydrostatic bearings • Temperature Compensation: Yes • Control Type: Manual (standard), with options for digital or CNC control systems • Probe System: Typically equipped with Renishaw or similar touch-trigger probes • Software Compatibility: Compatible with various metrology software platforms, including PC-DMIS and others

Semi - Automatic Butter Extruder and Shaping Machine fited on full stainless steel frame, Control panel. Two Stainless steel screw augers, stainless steel hopper. Manufacture : Dairy Machinery UK Model : DMUK EXSH1 Usage : Butter Extruding and Shaping Machine Shapes : Various Shapes and Sizes Condition : New Warranty : 12 months Spare Parts : Dairy Machinery UK

Crate washing machine Mohn Stainless steel

Impressions=0 m, Condition= Good , Availability= 2025-11-03, Size Max 76 x 106 Size Min 450 x 450 mm cardboard thickness 250-2000 gr/m2 Max corrugated thickness 5 mm Speed 6000 sh/h Pressure 300 tonn

Used blow moulding machine made by KRONES model Contiform S18. New 2004. It has 18 blow moulding stations. The maximum blow moulding speed is 24,000 bottles per hour for the 2.0 l format and 28,000 bottles per hour for the 1.5 l format. In February 2024, the machine was upgraded to support the PCO 2622 thread. The blow moulding machine has an integrated control system with visualisation in Polish, English and German. A complete set of documentation is included with the blow moulding machine. The blow moulding machine includes: an automatic glycol cooler, an automatic preform feeder, an automatic preform basket tipper and a bottle ejector mounted on an air transport conveyor.

Make Benhil Model: 8311 Junior Usage: Butter filling & wrapping Capacity: Up to 40 packages/min Product weight: 250 g Hopper with 2x screw augers Aluminium hopper and augers & Stainless Steel Hopper Condition : Good

[ 5000 characters max., no information about the advertiser ] Brand:MODUL Model:ZFWZ 2000/3 Type:Gear Hobbers Year:1981 Location:Czech Republic Specification: Max diameter of gear without tailstock 2100 mm Max diameter of gear with tailstock 1450 mm Max face of gear 1060mm Max module with hobbing head 22 Max/ Min center distance 1240/150 mm Min number of teeth 10 Max pressure angel 45 deg Table dia / number of slots 1800 mm/12 Bore in table / length 600/800 mm Max dia of hob / length 300/330 mm Max weight of workpiece 15000 kg Accessories: Standard milling head Tailstock (no clamping) Set of gear supports (shoes) Set of arbors Set of change gears

Machine: Benhil Multipack 8304 mini portion Capacity: up to 110 packets/min Pack size: 7,5, 10, 12,5 gram Dimensions: 30 x 40 x height adjustable max 20 mm Product: Butter / Margarine Wrap material: Aluminium foil Dimensions: Approx. 200 x 150 x 200 mm (l x w x h) Weight: 1.400 kg (gross) Electricity: 1.1 kW

Showroom machine / exhibition machine CMS Tecnocut - IDROLINE S 2040 Axle experience: X-axis: 4,250 mm Y-axis: 2,000 mm Z-axis: 200 mm C-axis: endless B-axis: +/- 60° Facilities: - 5-axis cutting head JD5Ax for inclined cuts up to 60° and automatic angle correction - Chain conveyor for automatic sand application - Automatic lifting doors to secure the working area - Sand dosator for automatic software controlled sand dosing - Central lubrication - Altitude probe with anti-collision system High pressure pump Greenjet Electric high-pressure pump with directly controlled servo motor Total current consumption: 34 kW at 5 ltr. / min Power connection: 400 V +/- 5% / 50 Hz Max water pressure 4,150 bar Pressure vessel 1.2 ltr Water passage: max. 5 ltr. / min DÃ?SE: 0.40 mm max. Incl. assembly / training and 12 months warranty!

Used blow moulding machine made by SIPA model SFR24. New 2007. It has 24 blow stations. The maximum blow speed is 38,000 bottles per hour for the 1.75 l format and 41,000 bottles per hour for the 1.5 l, 1.25 l, 1.0 l and 0.7 l formats. The device has an air recovery system and linear optical control for testing the quality of preforms. Supported thread type: PCO 1881. The blow moulding machine has an integrated control system with visualisation in Polish, English and Italian. A complete set of documentation is included with the blow moulding machine. The blow moulding machine includes: an automatic air-cooled chiller for supplying the machine with cooling water, an automatic preform feeder, an automatic preform basket tipper and a bottle ejector mounted on an air conveyor.

McIntyre Euro-strip 500 Cable Stripper The perfect bench-top cable stripper. Compact and efficient The Euro-strip 500 is one of the smallest in the range and is a low energy, large capacity unit that is easy to move around a yard. The Euro-strip Cable strippers are designed for simple, dependable operation without the need for constant adjustment, which suits all different material sizes. Taking up minimal space and emitting very low noise, the Euro-strip 500 will prove to be a valuable addition to your business.

Bessler - Wood Milling Machine Speed in 18mm Koskisen Grey consisting of a router table (X-axis), a portal (Y-axis), a Z-axis and a base frame filled with polymer concrete. Mechanics set: consisting of profile guides KPF-S 20 incl. carriage. Ball screw, for the Z-axis. Precision racks, with a gearing quality 8. Profile rails for the installation of limit switches. All sub-elements assembled. Machine feet adjustable. Control set: consisting of planetary gears, with a reduction ratio of 1:5 Stepper motors with 9.2NM, 4A. High-performance power amplifiers with 80V each, a 70V power supply and core transformer, completely pre-assembled in the control cabinet. Sensors for each axis. Protective device CE-compliant due to moving suction device. High-frequency spindle with 2.2KW incl. union nut, frequency converter, mains filter, brake resistor, as well as collet set. 21.5 ...

Wabäma Economy Plus bread cutting machine with long bread inserting tray suitable for 52cm of bread. -with sickle knife -with oiling -Built in 2007 -Cutting width adjustable -three-phase current 400 volts -Rated power 1.9 A -Control voltage 24 volts -Operating voltage 24 volts -Weight 285 kg

CMS Tecnocut Easyline Cutting range / axis experience: X-axis: 2,000 mm Y-axis: 4,000 mm Z-axis: 150 mm Uiaw3u8 C-axis: 630° B-axis: +/- 60° Included equipment: - 5-axis snow head incl. angle correction - Sand dosing and vacuum monitoring - Height scan - CAD/CAM - Laser - Central lubrication CMS Tecnocut GREENJET Highly efficient electric high-pressure pump. Technical data Total current consumption: 34 kW at 5 ltr. / min Power connection: 400 V +/- 5% / 50 Hz Max water pressure 4,150 bar Pressure vessel 1.2 ltr Water passage: max. 5 ltr. / min Opening diameter DÃ?SE: max. 0.40 mm The pressure translator with directly driven servo motor offers the following advantages: + Energy efficient + Proportional power consumption + no maintenance-free hydraulics + 75 dBA + Low maintenance due to 60% less structural components + internal water pump + ...

The machine originates from a high-profile pharmaceutical & cosmetic manufacturing plant (part of a large Pharma group that operates 18 industrial sites and 3 development centres located across Europe). Year: 2008 Excellent condition with little use. 3M-Matic™ Adjustable Case Sealer 700a-s is as a used case sealer, designed to seal the top and bottom centre seams of up to 30 cartons per minute. Working Description: Fully guarded construction-suitable for demanding Pharmaceutical and Food grade manufacturing areas Stainless steel construction for use in corrosive and high moisture environments Equipped with 3M™ AccuGlide™ SST Taping Heads designed to apply a C” clip of Scotch® pressure-sensitive type film box sealing tape to the top and bottom centre seam of regular slotted containers. Adjustable top and bottom belt drive syst ...

Below you can see the first impressions of our mobile screening machine, which was designed for separation tasks in the outdoor area. The system can separate different types of material into two fractions, depending on the selection of the mesh widths, the degree of the sifted material can be adjusted. The two fractions are discharged into wheelbarrows via the outlets of the screening machine. For the removal of fine goods, the stern must be removed. The coarse material enters another wheelbarrow or a suitable container via a second slide. The mobile screening machine can be rented and purchased. Ready to drive 450Kg

1 of used film-only multi-packer, make KHS, type Innopack Kisters SP 050 B2, new 2013. Operating side: links. Used for PET bottles 250/500 ml as 3x2=6-packs (dual lane) and 6x2=12-packs as well as 6x4=24-packs (single lane) in clear or print-registered film. Quick change-over via servos and spindles. Capacity upto 50 cycles per minute. Siemens S7 controls.

TECHNICAL SPECIFICATIONS Manufacturer: August Müller Rottweil (AMR) Description: Finger roller grate Type: Stationary Type: 11-F2-5/15 Year of Make: 2019 Slope: 11° Power: 3 x 22 kW / 400V Number of rotary shafts: 15 pieces Max. feed capacity: 150 - 250 t/h Max. drop height on the finger roller grate: 2000 mm Max. size of the feed material: 0 - 120 mm Sieving: 0 - 25 mm Weight: 16,000 kg Max. external dimensions (L/W/H): 5800mm x 2950mm x 2550mm SPECIFIC COMMENT - Plant has only been in operation for about 3 years - Processing of heavily contaminated screening waste - Spinning, equalization and cleaning of the feed material - Dismantling and loading included in the offer

Ger RHC1500 Universal Rectifier. Indoor head. Distance between points: 1500mm. Maximum part diameter: 355mm. Point height: 180mm. Tooth diameter: 400mm. Power: 7.5hp. Weight: 4500Kgs.

Parts cleaning system Industrial washing machine degreasing made entirely of stainless steel! Manufacturer Render Type W175 Built: 1994 5 loading trolleys with 5 washing baskets, Basket size 1,125 x 1,125 mm Manual workstation with viewing window on one side with integrated high-pressure cleaner. Machine to be loaded/unloaded from both sides! Machine comes from an operating resolution and was in use until dismantling. Tank capacity approx. 2,000 litres, oil scimmers, filters, high-pressure pumps... Vertical door opening (lifting doors) on two opposite sides. This allows you to load on one side and unload on the other side. Due to the very high inner height, the system offers an optimal possibility to accommodate both very heavy laundry material as well as parts with large dimensions.

No 2 circular blades motors HP 3 - 2800 rpm No 5 drilling units motors HP 1 - 2800 rpm No 1 conveyor belt feeding machine HP 0,5 - 1400 rpm Pneumatic movements with hydraulic brake Stacking / Destacking device with pneumatic cylinders Electro-pneumatic machine control with PLC: Overall dimensions: -Length Mm: 2500 (useful for cutting and drilling) -Height Mm: 1400 -Width Mm: 1800

ALPHA Q 351 PROGRESS PULS MM WLG FD • Year 2016 • Inverter welding machine, DC, pulse, water-cooled • Multiprocess: MIG/MAG, TIG lift arc, MMA, air arc gouging • Water-cooled MIG/MAG inverter welding machine, pulse, with separate wire feeder Excellent Multimatrix welding characteristics • Equipped with Synergic characteristics for EWM coldArc, EWM coldArc puls, EWM pipeSolution, EWM forceArc, EWM forceArc puls, EWM rootArc, EWM rootArc puls and superPuls • Adjustable start and end-crater functions • Program operation with 16 programs per JOB • Equipped with Synergic characteristics for GMAW welding of steel/CrNi/aluminium • Infinitely adjustable arc dynamics (choke effect) • Large power reserves thanks to high duty cycle with all components heating up less as a result, guaranteeing a longer service life for machines when in use •  ...

The cross-welding stamp of the packaging machine is closed by a servo motor and is infinitely variable. The width of the infeed belt is infinitely adjustable via a hand crank, which allows perfect, simple and uncomplicated adjustment of the product width. The parameters are entered via a modern, easy-to-use touch screen. The flow length is controlled photoelectrically, so that different package lengths can be packed one after the other and one after the other. The machine is technically designed for very tight, perfect shrink-wrapping of the products, so that optimal packaging results are achieved in any case. The machine works with an automatic film feeder, it is possible to work with different transport speeds. Longitudinal and transverse welding are permanently heated and easy to control via the touch screen. Product Dimensions: Length: min. 50 mm, max. endless Width: min.  ...

Hydraulic rescue scissors operated with hydraulic pump (630bar) internal combustion engine. To be used as e.g. cable scissors for use in areas without power supply. 1 fuel-powered hydraulic unit 1 hydraulic scissors 1 hydraulic spreader Npjrx All the goods in very good, ready-to-use condition.

Band saw Jespa 340/630 HAP column guided Band saw Jespa Semi-automatic Type 340/630 HAP Column-guided Built in 2009 Saw blade length 5.150mm

Milling machine from a training workshop in very good condition Manufacturer lid Type FP1 Active

running direction: right - left for 28 mm VacuVent closure with safety housing

Pos. 9749.13 - 1 MAYER type Relanit 3.2 II, gauge 28, diameter 30, jersey open knit, 2640 needles, 96 feeders, lycra, 3+1 tracks Pos. 9750.11 - 1 MAYER type Relanit 4, gauge 28, diameter 30, jersey tubular knit, 2640 needles, 96 feeders, 3+1 tracks Pos. 9751.18 - 1 MAYER type Relanit 4, gauge 24 installed and spare cylinder gauge 28, diameter 30, jersey tubular knit, 2268 needles, 96 feeders, 3+1 tracks Pos. 9752.1 - 1 MAYER type MV4 II, gauge 20 installed and spare cylinders gauge 24 and 28, diameter 30, jersey tubular knit, 1872 needles, 96 feeders, 4 tracks Pos. 9753.8 - 1 MAYER type FLF, gauge 14, diameter 30, rib tubular knit, 2 x 1320 needles, 44 feeders, lycra, 1/1 tracks Pos. 9754.5 - 1 MAYER type MLBF, gauge 22, diameter 30, plush tubular knit, 2068 needles, 96 feeders, 4 tracks Pos. 9755.17 - 1 SANTONI type Zenit SV, gauge 28, diameter 34, jersey open knit, 29 ...

Pass width mm: 1300 02 Engines KW: 1 + 1 02 Brushes Brush diameter mm: 300 Vacuum table Control cabinet KW: 8.5

Grinding units Grinding belt length mm: 8000 Grinding width mm: 120 Feed max: 2200 m/min Manipulation unit Max machining range mm: 2100x650x400 Total connection kW: 7.2

DATASHEET – RAMO TN20 CNC LATHE Manufacturer: RAMO Industrie SA Model: TN20 Numerical control: NUM 1060 (Telemechanical) Type: Inclined Bench CNC Lathe Condition: Good general condition, visible machine under power ⚙️ TECHNICAL SPECIFICATIONS Power supply: 3 × 400 V – 50 Hz Current rating: 63 A Control voltage: 110 V ~ Signaling voltage: 110 V ~ Lighting voltage: 220 V ~ Clutch voltage: 24 V = MECHANICAL CAPACITIES (TN20 standard) Turning diameter above the bed: 420 mm Turning diameter above carriage: 250 mm Length between toes: 500 mm Z-axis travel: 500 mm X-axis travel: 200 mm Spindle passage: Ø 40 mm Spindle speed: 30 to 4000 rpm Spindle Cone: Camlock D1-4 Spindle motor power: 7.5 kW Fast feeds: 10 m/min (X and Z axis) Tool Turret: 8 automatic positions DIMENSIONS AND WEIGHT Dimensions (W × D × H): app ...

DMG Mori Seiki LaserTec 50 FineCutting Sauer CNC Laser Precision Machine Year / Model: 2019 Control: Celos with Siemens 840D sl Operate CELOS with Siemens 840D sl Operate including 2l .5 ERGOline Control with multi-touch screen CNC Laser Precision Machine with High Speed Machining LASERTEC 50 FineCutting for laser fine cutting, laser drilling, laser welding NC swivel rotary table highly dynamic and precise Travel: 500 mm x 500 mm x 700 mm travel integrated ytterbium cw fiber laser 450W qcw ytterbium fiber laser with 4500W Pulse peak power and 450 W power Processing head (80 mm focal length), 5-axis transformation 100 working hours (new-new) Kaufpreis neu/Buying price in year 2020: 890.000,- Eur, Made in DMG Germany. Included: Fanuc robot automation + Keller autom. Extraction system solid machine base frame made of mineral casting, Camera through optical path for fib ...

Grinding width mm: 1350 Pass-through height mm: 3 - 160 Feed max m/min: 2 - 20 - Inverter KW 3 01 Grinding unit: Grinding belt length mm: 1380 x 3250 - 24 SH - 15 KW Blow-off device Vacuum table Scotch Brite x mm 200 Machine Control: Viet "IPC 15" Touch Screen Centering device Weight Kg: 3970

Pass height max mm: 2000 Battery: 24V Chargers: automatic and high-frequency Automatic reading of the charging height: Reflective light barrier Total power: 0.75 KW

Machine Type: Hot Air Welding Machine Manufacturer: Pfaff Type: 8304 Year of Make: 2002 Condition: used / in working order Offer will only be sent if a complete imprint is provided! Price 2.750 Euro incl. 19% VAT 2.310,92 Euro net Location Warstein , Germany Reference M-PFA-1125-4 DESCRIPTION We offer you a used hot air welding machine from the manufacturer Pfaff. Availability: immediately Our offer is aimed at tradespeople who are registered within the meaning of the Trade Regulation Act according to §14 GewO. The offer is subject to change, subject to prior sale. Please provide your full contact details to receive a quote with our terms and conditions of payment. Errors in the descriptions and offers are reserved

Grinding width mm: 1350 Pass-through height mm: 3 - 160 Feed max m/min: 2 - 20 - Inverter KW 4 01 Grinding unit: Grinding belt length mm: 1380 x 3250 - 15 KW (INV) 01 Orbital grinding unit "Spinbrush" - KW 4 (INV) 01 Grinding unit: Grinding belt length mm: 1380 x 3250 - 15 KW (INV) Machine Control: Viet "IPC 15" Touch Screen Blow-off device 1 Blow-off device 2 Vacuum table Scotch Brite Weight KG: 7200

Key data: 40 , 200 , 1340

The all-electric servo bending machine is one of the products with independent intellectual property rights developed by our company. Special high-load screw and guide rail structure, imported bearing installation, high load-bearing capacity, high positioning accuracy, long life, machine tool rigidity, precision retention, and reliability are close to perfection. By introducing advanced design concepts and scientific design methods, the shortcomings that traditional designs cannot avoid have been solved. This bending machine is fast and simple to program, can realize concurrent linkage of multiple axes, fast feed positioning, and significantly improves the efficiency, accuracy and consistency of bending, which is far superior to traditional hydraulic bending machines, and does not require the use of hydraulic oil, is environmentally friendly and pollution-free. Compared with traditional ...

Travel x 350 mm y 250 mm z 220 mm Water bath machine Automatic wire threading Glass scales x / y incl. box for large coils incl. cooler incl. functional guarantee

Sweeping width mm: 880 Number of brushes: 2 Weight: Kg 646 Total connection KW: 3

Length: 2900 mm

Key data: 420 mm, 650 mm

Machine Type: CNC Lathe Manufacturer: Okuma Type: LB400M-1SC Year of Make: 2000 Commissioning: 2001 Control: OSP-U100L Spindle hours: 14502 hrs Delivery time: in stock Machinery - Interior extraction from Hengst Filtration (built in 2023) - Touchsetter, tool measurement - C-axis (main spindle) - Tool breakage and wear monitoring - 3-jaw chuck, Kitagawa B210, Ø250 - Tailstock available - Coolant supply, also available through the tool - Dialogue programming IGF - Chip conveyor (scraper) Technical details - Max. turning length: 650 mm - Max. turning diameter: 420 mm - X-axis travel: 300 mm - Travel Z-axis: 675 mm - Travel C-axis: 360° - Chuck passage: 72 mm - Spindle passage: 95 mm - Clamping cylinder passage: 95 mm - Tool holder: VDI 40 - Tool stations: Stations 12 - Spindle speed: 2800 rpm - Main spindle power: 22/30 kW - M-spindle ...

-Car stainless steel -9 cloth drawers each 173x92cm