Used line for the production of yellow cheese from Obram. Capacity 10,000 kg/day.
TOP SELLER
Complete falling film vacuum evaporator, previously used for skimmed milk or sweetened whole milk, consisting of a 4 effect TVR Evaporator. Still mounted in the cheese plant in Spain till end of April 2026. The product feed rates in the installation are ± 14 t/h with a comparative temperature between 73 and 50°C from the 1st to the 4th effect., Processing rates used by the current plant for skimmed milk:, - Infeed flow: 14.000 kg/h @ 9% DM, - Infeed temperature: 5 °C, - Water Evaporation: 11.375 kg/h, - Outfeed flow: 2.625 kg/h @ 48% DM, - Steam consumption: 2.050 kg/h, Processing rates used by the current plant for sweetened whole milk:, - Infeed flow: 14.000 kg/h @ 25% DM, - Infeed temperature: 5 °C, - Water Evaporation: 7.637 kg/h, - Outfeed flow: 6.363 kg/h @ 55% DM, - Steam consumption: 1.375 kg/h, Approximately operating temperatures:, - First effect (steam side): 73 °C, - Fir ...
APV COMBI UHT TREATMENT STERILIZATION PASTEURIZATION PLANT – 2006 Includes both TUBULAR and INJECTION systems. Capacity 4.000 - 8.000 Lt /h DISASSEMBLED AND READY FOR LOADING - APV PLATE HEAT EXCHANGER for cooling - APV TUBULAR ( INDIRECT ) UHT Treatment system. - APV INJECTION ( DIRECT STEAM ) UHT Treatment system. - APV ASEPTIC HOMOGENIZER 250 BAR - OPTIONAL - APV CIP CLEANING UNIT - APV VALVE CLUSTER FOR ASEPTIC TANK - (TANK IS EXCLUDED) - ELECTRIC CONTROL PANELS Fast heating (~300°C/sec) for optimal taste and minimal degradation Instantaneous flash cooling for flavor and aroma preservation Uniform heating via indirect tubular exchangers for gentle thermal treatment High energy recovery (up to 90%) to reduce utility consumption and cost. Precise thermal control with uniform product treatment Efficient spore kill with very lo ...
TOP SELLER
Tebel OST-IV Closed cheese vat of 8.000 ltr. Double jacketed for injection of steam or hot water so the temperature of the milk inside the vat can be indirectly adjusted. Stirring, cutting tools, welded to a horizontal shaft. This is driven by a drive unit with frequency converter. During cutting the tools rotate in the opposite direction as during stirring. The coagulum is cut by sharp radial knives of stainless steel. Whey can be drawn off through a perforated pipe (whey suction device). This pipe is lowered into the whey until it is only just immersed. The curd is discharged through the bottom valve. The vat is inclined (4%) toward the bottom valve to facilitate emptying. After a production run the vat is cleaned by four rotating CIP nozzles located in the top. All parts are made of stainless steel AISI 304 except the drive unit. Stainless steel MCC panel at the backside, close to the ...
Milk Pasteurisation Set With Seital Separator 2000-3000[tel:2000-3000] L/h Description This Combined GEA VT 10 pasteuriser with Seital Cream Separator was used on Cheese and Fresh milk products. This is ideal for a small/medium sized dairy wanting to move away from manual cleaning separators and Bach Pasteurization process gaining time, efficiency and product quality . Having a cream separator opens new markets for the dairy such as butter, cream, clotted cream, skimmed milk and zero fat milk products are some of the opportunities. Pasteuriser Make : GEA Model : VT 10 Year of Manufacture : 2005 S/N : 169/15597[tel:169/15597] Temperatures: Shown in Chart Hot Water inlet PHE Balance Tank Temperature Valve regulation Diver Valve for non pasteurised product Chart Recorder Product pumps Water Pump Stainless steel skid mounted for quick installation Co ...
, from the manufacturer (built in 2002) are available for sale, each with a . , totaling approx. 3,534 hl. The tanks are insulated, clad and have three frame cooling zones and cone cooling for precise temperature control. Each tank is designed for a maximum overpressure of 2 bar and can be used at operating temperatures of -10 to 50 °C. The total cooling area is 13.3 m². With a robust stainless steel construction and upright positioning, the tanks are ideal for breweries or beverage manufacturers that require temperature-controlled fermentation and storage processes. Individual sale possible. Our team at VBW Asset Trade will be happy to answer your questions., Additional title: vertical, coolable stainless steel tanks, Gross volume: 58890 l, Max. overpressure: 2 bar, Operating temperature: -10 to 50 °C, Total cooling area: 13,3 m², Length: 3370 mm, Width: 3370 mm, Height: ...
Juice Preparation Plant – Tetra Pak Processing System Complete juice preparation and pasteurization plant designed for the production of fruit juices and beverage bases. The system includes Tetra Almix Spark, Tetra Alblend Spark, and Tetra Steridrink pasteurization equipment, providing reliable mixing, blending, and thermal treatment for industrial beverage production. A) Tetra Almix Spark 020V - High-performance mixing and dissolving system used for preparing beverage bases and ingredients before blending or pasteurization. General Information - Manufacturer: Tetra Pak - Model: Tetra Almix Spark 020V - Year of Manufacture: 2001 Capacity - Production Capacity: 0 – 15,000 l/h Installed Options - Vacuum cleaner - Drum emptying station - Utility Requirements - Sealing Water - Connection: 1/2" - Capacity: 700 l/h - Temperature: 15°C - Pressure: ...
The Waukesha Cherry-Burrell 015 is a rotary positive displacement pump which can handle dairy products (e.g., yoghurt, quark, curd and butter), solids (e.g., cherries and olives), slurries, pastes, and a variety of liquids. If wetted, they offer self-priming performance. A gentle pumping action minimizes product degradation. They also offer continuous and intermittent reversible flows and can operate dry for brief periods of time. Flow is relatively independent of changes in process pressure to, so output is relatively constant and continuous. Duo - twin wing stainless steel lobes. Nominal displacement: 0,054 liter per revolution. Maximum nominal capacity: 2,0 m3/h. Inlet / Outlet connection: 1-1/2. Maximum product pressure: 13,8 bar. Maximum pump speed: 700 rpm. The pump is used in a ice cream factory for product pumping. The current motor with this pump is 0,75 kW - 1,395 rpm - 380/420 ...
Used Stork UHT Plant – Model 2000 Reliable UHT processing plant designed for the sterilization and treatment of dairy and plant-based beverages. The Stork Model 2000 offers efficient thermal processing and is suitable for medium-capacity production of UHT products. General Information - Manufacturer: Stork - Model: 2000 - Refurbishment: Completely refurbished in 2015 - Condition: Very good used condition Technical Specifications - Capacity: 1,600 l/h - Control System: Siemens S7 PLC Suitable Products - The plant is designed for processing a wide range of UHT beverages, including: - UHT milk (plain / white) - Chocolate milk - Flavoured milk - Soya UHT drinks Key Advantages - Reliable Stork UHT processing technology - Completely refurbished in 2015 - Suitable for dairy and plant-based beverages - Equipped with Siemens S7 PLC control system - Compact solutio ...
Tebel OST-IV Closed cheese vat of 8.000 ltr. Double jacketed for injection of steam or hot water so the temperature of the milk inside the vat can be indirectly adjusted. Stirring, cutting tools, welded to a horizontal shaft. This is driven by a drive unit with frequency converter. During cutting the tools rotate in the opposite direction as during stirring. The coagulum is cut by sharp radial knives of stainless steel. Whey can be drawn off through a perforated pipe (whey suction device). This pipe is lowered into the whey until it is only just immersed. The curd is discharged through the bottom valve. The vat is inclined (4%) toward the bottom valve to facilitate emptying. After a production run the vat is cleaned by four rotating CIP nozzles located in the top. All parts are made of stainless steel AISI 304 except the drive unit. Stainless steel MCC panel at the backside, close to the ...
Used line for the production of cottage cheese and cream. New: 2010. cottage cheese preparation section coagulation boiler - 10m3 diaphragm pump - 10 m3/h final product preparation section whey separator - 10 m3/h creamer 09CR02 - 3 m3 (working capacity) cream dosing system FRISTAM pump - 5 m3/h input (pulp) dosing system FRISTAM pump - 2 m3/h static mixer product piston pump for Hugart packing machine – 2m3/h
Tetra Pak Tetra Therm Aseptic Visco Line for pasteurisation / sterilization of concentrated beverage bases by a Tubular Heat Exchanger (THE) system. Capacity 2.600 up to 8.150 liter per hour. At the current plant the line is used for products up to 100 °C. The indirect heating temperature is up to a maximum of 135 °C. Holding time set at 0 / 5 / 10 seconds. CIP Cleanable., In the Tetra Therm Aseptic Visco system, heating and cooling will take place in Tetra Spiraflo MTC tubular heat exchangers. Modules with a narrow ring section are used for heating and cooling to ensure optimal heat transfer. The product is pre-heated in stages within the Spiraflo tubular heat exchangers. The Spiraflo tubular heat exchanger is equipped with a sliding O-ring system. This means that the product and the outer tubes are not welded together. This prevents stress corrosion cracking and minimizes maintenance ...
Different kind of sheeted and rolled breads. Niittypitko 2000 pcs / h, 2 rows, dough thickness 3-4 mm Coffee bread Kranssi 2000 pcs / h, 2 rows, dough thickness 3-4 mm Muhku, 10 000 pcs / h, 8 rows, dough thickness 6-8 mm Ciabatta, 7200 pcs / h, 6 rows Folded bread, 4800 pcs / h, 4 rows, dough thickness 5 mm Capacity based on 20 strokes per minute for the retracting belt, in combination with the product discharge conveyor system Product specification: Manufacturer: Rademaker Holland Type: Crusto bread line Year: 2008 Voltage: 3 x 400 v + N + Pe, 50 Hz Control voltage: 24 Vdc Power consumption: 21, 9 kW Inom: 41 A, max fuse 50 A Avarage air consumption: 196 nl / min Max air consumption: 548 nl / min Dimension: L 21 000 mm, W 3000 mm, H 6000 mm
Margarine pilot plant with 1x high pressure pump, 3x crystalizer scrap surface heat exchangers (SSHE), 1x pin worker (1 - 2 and 3 liter), 1x phase inverter, 1x cooling unit (R22) and control panel. Working product pressure of the pilot plant up to 80 bar (8000 kPa). Capacity up to 90 kg per hour., - High Pressure Pump, High Pressure Pump for pumping the margarine emulsion through the margarine pilot plant. Gerstenberg & Agger A/S, type Labo Pump 2-22-4 , serial number 12.211, year 1990, product pressure max 80 bar, temperature max 100 °C, capacity max 200 kg/h, motor 415 V - 50 Hz - 1,1 kW. Control panel with Siemens S7-200 PLC., - Scraped Surface Heat Exchanger 01, Cooler., Pilot G&A Perfector - SSHE Cooler Perfector 57 is designed for lenient cooling of medium viscosity, pumpable food like margarine. Gerstenberg & Agger A/S, type Perfector Lab 1x57, serial number 12910, year 1993, dut ...
Used line for processing green bean by Femia. New 2007. capacity: 5000 kg/h. The line consists of: 1. Descaler. 2. Rinser. 3. Rod splitter. 4. Rod cutter. 5. Aerator. 6. Vibrating distributor. 7. Bean tip cutters. 4 pcs. 8. Conveyors.
The Mac Ewans Centrifugal pump is a pump for use in sanitary applications. Previous used in a Casein plant. Motor: 7,5 kW - 400 V - 50 Hz - 1.440 rpm - 14,2 A. Diameter of the impellor: 180 mm. Connections on the inlet: 70 mm. Connections on the outlet: 60 mm. Estimated capacity: ± 20.000 ltr/h., macewans.co.nz/, Type of Machine: Centrifugal pump, Stock Number: 1444, Diameter of the impellor: 180 mm, Motor: 7,5 kW - 400 V - 50 Hz - 1.440 rpm - 14,2 A, Estimated capacity: ± 20 m3/h
Used line for the production of chocolate "bodies". Year of production 2008. The line includes: - acid-resistant tank with a capacity of 1000 L - 250L double ribbon mixer - CFA 3 body molding machine - TCH-600 pre-cooling tunnel
The APV Cleanline CL3/078/20 is a positive displacement rotary lobe pump with sanitary design which can handle dairy products (e.g., yoghurt, quark, curd and butter), foodprocessing, beverage, cosmetics, pharmaceutical and fine chemicals industries. This pump is perfect for managing all kinds of fluid, of either low or high viscosity, as well as for filtering and bottling applications. Products containing fragile solids such as curd can be pumped without damage thanks to the specially designed lobes. Tri-lobe stainless steel lobes / rotors. Nominal displacement: 0,780 liter per revolution. Maximum nominal capacity: 33,7 m3/h. Inlet connection: 80 mm. Outlet connection: 71 mm. Maximum product pressure: 7 bar Maximum pump speed: 720 rpm. Maximum temperature: 110 °C. The pump is used in a dairy for product pumping. The current motor with this pump is 5,5 kW - 1.430 rpm - 400 V - 50 Hz - 11 ...
Make : Armfield Capacity : 40 litres Mixing : Silverson Mixer Processing vessel with cooling Usage : Pasteuriser and mixing vesle Model: FT 40 Make : Armfield Model : FT 75 Usage : Crystaliser Pin mixer Single tube Usage : Margarine and ice cream Make : Armfield Model : UHT Usage : UHT Pasteuriser All in excellent condition came out of university in UK
Tetra Pak Tetra Spiraflo Tubular Heat Exchanger (THE) previously used in a dairy for whey protein as pre-heater with indirect hotwater preparation (15 - 70 °C), holding section (1 - 3 minutes) and cooling section (65 - 10 °C)., Unit exist out of:, - 7x tubes for pre-heating (Tetra Pak MT-38/1x20s-6, total surface area: 2,25 m2, product connection DN25, hotwater connection DN20 with indirect hot water system with plate heat exchangers, pumps (CH18-10 A-W-G-BQQV - 7,5 m3/h - 0,72 kW), steam valves (Samson), expansion vats, manual valves and interconnecting piping., - 9x tubes for cooling (Tetra Pak MT-70/4x16s-6s-1, jacket: 20 bar - 110°C - 16 liter, inside: 50 bar - 110 °C - 3,6 liter, total surface area: 10,17 m2, product connection DN38, (ice)water connection DN50)., - Flowmeter (Endress+Hauser - Promag 300)., - Holding tube, DN 40 (6x 6 meter), complete with bracket and swivel bend ...
Knobel line and a W&D line shot depositor for chocolate. Dosing machine for tempered chocolate with agitator or other liquid as well as slightly viscous products also AWEMA moulding line Hacos chocolate moulding line
The SPX Waukesha Cherry-Burrell 220 U1 is a rotary positive displacement pump which can handle dairy products (e.g., yoghurt, quark, curd and butter), solids (e.g., cherries and olives), slurries, pastes, and a variety of liquids. If wetted, they offer self-priming performance. A gentle pumping action minimizes product degradation. They also offer continuous and intermittent reversible flows and can operate dry for brief periods of time. Flow is relatively independent of changes in process pressure to, so output is relatively constant and continuous. Duo - twin wing stainless steel lobes. Nominal displacement: 1,976 liter per revolution. Maximum nominal capacity: 70,4 m3/h. Inlet connection: 3. Outlet connection: 3. Maximum product pressure: 13,8 bar Maximum pump speed: 600 rpm. The pump is used in a dairy for product pumping. The current motor with this pump is 7,5 kW - 1.445 rpm - 400 ...
Continuous Butter Churn Complete plant with PHE , controls, butter milk pump, tanks . Condition Good condition . Contact us for more information.
Continuous Butter Making Machine (CBM) which has a production capacity of ± 1.000 kg of sweet, sour, or cultured butter per hour (salted or unsalted). It operates with an input of approximately 2.000 liters of cultured and/or sweet cream per hour (35–42% fat, pH ~4.8, inlet temperature 8–13 °C). The unit is fully electrically driven. All product-contact parts and the frame constructed from stainless steel. It is CIP-cleanable for hygienic operation., The system is supplied with two separate stainless steel skids., Process skid, including:, - Balance tank, - Feed pump, - Vacuum system, - Ice water system, - Flow transmitter at cream inlet (ltr/h), - Buttermilk and CIP collecting tank, - Buttermilk/CIP pump, - Buttermilk plate cooler, - Interconnecting piping and manual valves, - Stainless steel control panel with Siemens S7 PLC, Exor touchscreen HMI, and Danfoss frequency converters ...
used
Continuous Butter Churn Complete plant with PHE , controls, butter milk pump, tanks . Condition Good condition . Contact us for more information.
Milk pasteurisation line of 25.000 ltr/h with cream separator / skimmer. Temperature cylce: ± 3/4° (in) - regeneration - ± 55 °C (separator) - ± 72/75 °C (pasteurisation) - holding - regeneration - ± 3/4 °C (out). Line existing out of open level tank (2x lid, spraybowl), product pump (APV Puma), digital flow transmitter (Yokogawa FLXA402), Transmitter (Rosemount 8712) plate heat exchanger (APV N35 RKS, year: 2004, serial nr 1286, drawing no: NZ0321, 4 sections, working pressure 6 bar), cream separator / skimmer (Westfalia MSA200-01-076, year 1980, serial nr 1669 641, self cleaning, bowl, motor (37 kW), motor cover, base plate with feet, water valves (original Westfalia), control panel including original GEA operation panel, all inlet / outlet pipes with pumps, flow indicator and service tools for maintenance including pressing tool), holding tube with slope, booster pump (APV Pum ...
Rademaker / Rondo ‘salmon en croute’ line Rademaker block processor with Rondo make up line. Has been producing ‘Salmon en croute’ for major UK supermarkets. Whole line is in lovely condition and can obviously be easily adapted to run other products like pasties, sausage rolls etc. Mainly used seasonally so only 11,800 running hours.
On behalf of our client, we are requested to offer this Pasta filata cheese line for sale, due to increasing production at the current factory. The whole line is delivered and built up by Sulbana AG Switzerland in 2019 and it is out of production for ± 1 year. The pasta filata cheese line produce products like Mozzarella, Burrata, Kashkaval, Pizza Cheese etc. The capacity of the line is 200 to 800 kg per hour. The line is already dismantled and located in the warehouse of the dairy in Germany, where it can be inspected., The line exist out of the following components:, - Elevator for lifting normcar trolleys of 200 liter with basic ingredients including tipping unit to empty the trolleys inside the feeding bunker. Max load: 350 kg. Manufacturer: Frontmatec Hygiene GmbH, type: Hebe- Und Kippvorrichtung, model: 27000, serial number: P-10259, year: 2019, motor: 0,75 kW - 400 V - 50 Hz., - ...
Make : Roversi Tank Volume :3000 liters Cream Capacity : 1000 Litres to 1500 Litres Double jacketed Kneading Rolls inside the barrel Control panel Stainless steel production area Skid Mounted 2 Door Safety closer See through glass Fully Refurbished on order Manufacturer Roversi Model 3000 L
The Alfa Laval MR-200 Sanitary Self Priming Liquid-ring Pump is a pump specially designed for food, chemical, pharmaceutical and other industries where acid-resistant steel is resistant to the products to be pumped. All products wetted parts, i.e. pump casing, casing cover and impeller are made of acid-resistant steel AlSl 316. Clamp screws and legs are made of stainless steel AlSl 304. lntermediate part is in cast iron which is zinc coated and laquered making it highly corrosion resistant. Motor: 7,5 kW - 380/420 V - 50 Hz - 1.450 rpm - 15,3 A. Impeller diameter: 199 mm. Connections on the inlet / outlet: SMS 76 mm (3). Current maximum capacity (based on the available Alfa Laval performance curves and the current motor): 48.000 ltr/h @ 0 Bar., Type of Machine: Sanitary Self Priming Liquid-ring Pump, Stock Number: 1511, Diameter of the impellor: 199 mm, Motor: 7,5 kW - 380/420 V - 50 Hz ...
CHEESE PORTION CUTTING MACHINE SLICING MACHINE AGED CHEESES GOUDA, EDAM, MIMOLETTE, CHEDDAR AND MANY KINDS WITH PLC CONTROL AND HMI OPERATOR PANEL COMPLETE STAINLESS STEEL THICKNESS IS ADJUSTABLE
Unused Alfa Laval ThinkTop V50 is a valve-top control unit that provides surveillance and control of valves during the fluid handling process. The control unit has been developed with user friendliness and robustness in mind. The V50 series is the compact option with a feature set tailored to valves that require only one solenoid valve such as butterfly and single seat valves. Solenoid valves 1 x 3/2. Digital 24 VDC. Article number: 9615400403., Type of Machine: Valve-top control unit, Art. no.: 9615400403
Unused Alfa Laval LKB Butterfly Valve which is a reliable, hygienic in-line valve for routing low and medium-viscosity liquids in stainless steel pipe systems due to its substantial opening area and low flow resistance. This hygienic valve is designed for on-off duties with low to medium-viscosity liquids in hygienic applications across the dairy, food, beverage, brewery and many other industries. Article number: 9612628569. EPDM 316L KIT ACT LKLA-T Ø85 NC 6 MM. This LKB valve is with a pneumatic actuator for pneumatic operation (item code: 9612194003, AIR-ACTUATOR LKLA-T-85 NC 76,1 MM/DN 65-80)., Type of Machine: Butterfly Valve, Art. no.: 9612628569, Pneumatic Actuator: Yes
Unused Alfa Laval LKB Butterfly Valve which is a reliable, hygienic in-line valve for routing low and medium-viscosity liquids in stainless steel pipe systems due to its substantial opening area and low flow resistance. This hygienic valve is designed for on-off duties with low to medium-viscosity liquids in hygienic applications across the dairy, food, beverage, brewery and many other industries. Article number: 9612628569. EPDM 316L KIT ACT LKLA-T Ø85 NC 6 MM. This LKB valve is with a pneumatic actuator for pneumatic operation (item code: 9612194003, AIR-ACTUATOR LKLA-T-85 NC 76,1 MM/DN 65-80)., Type of Machine: Butterfly Valve, Art. no.: 9612628569, Pneumatic Actuator: Yes
Unused Alfa Laval ThinkTop V70 is a valve-top control unit that provides surveillance and control of valves during the fluid handling process. The control unit has been developed with user friendliness and robustness in mind. The V70 series is the more flexible option compare to the V50, that can be configured to meet the needs of the most demanding valve applications such as Mixproof valves. Solenoid valves 3 x 3/2. Digital 24 VDC. Article number: 9615400012., Type of Machine: Valve-top control unit, Art. no.: 9615400012
On behalf of our client, we are requested to offer this Cheddar Cheese Plant for sale, because of bankrupcy of the previous owner. The whole line is delivered and built up in 2021 and has been in production for 1,5 years only., The line is already dismantled and packed for transport. It can still be inspected on the actual factory site in the warehouse., The capacity of the cheddar cheese plant was during production of the previous owner set at a milk intake of 50.000 pounds per hour, 20 hours per day = 1.000.000 pounds of milk per day, which means ± 100.000 pounds of cheddar cheese per day (= ± 45.359 kg of Cheddar cheese per day) = ± 2.500 Cheddar cheese blocks of 40 pounds per day (= ± 18,14 kg). Dimensions of the cheddar blocks: 35 x 28 x height cm., The available list of equipment exist out of:, - 4x Closed cheesevats, Manufacturer: Walker (supplied by Kusel), Model: Double O, V ...
Luwa SMS GmbH LN-0200 - Vertical Thin Film Evaporator consist of a cylindrical, vertically-arranged body with heating jacket. A rotor inside the body is equipped with rows of pendulum blades along the full length of the dryer., Special thin-film evaporator designed for dairy service, discharge system, vapor pipe, condenser, and drives. It was in used as a pilot plant on a dairy service until early 2001 and afterwards converted to a 2 square metre cheese base processor with discharge system and ran till 2025 in a Casein plant in a dairy factory in New Zealand., The vertical thin film dryers operate as follows: The wet feed is spread by the pendulum blades in a thin layer onto the heated wall. During this process, the volatile components evaporate continuously out of the product layer at high evaporation rates. The pendulum blades are designed with a minimum gap to the heated wall to preve ...
Koch Membrane Systems (GEA Tuchenhagen computer designed) Ultra Filtration (UF) plant for continuous circulation / concentration / filtration and the production of double cream cheese (philadelphia style). Once the plant is running continuously with ratio control, no manual interventions are generally necessary for the production of the UF concentrate. However, for optimal production of consistent quality, strict adherence to various prerequisites is necessary, e.g. regarding cleaning. Line still located at its original position in the dairy in Austria., The Ultra Filtration line exist out:, - Level tank, 750 liter., - Product feed pump (P1), Tuchenhagen VPB 32 L, 5.000 ltr/h, 39 mWs, motor 3 kW - 2.900 rpm - 380 V - 50 Hz., - Permeate pump (P2), Tuchenhagen VPB 32 L, 5.000 ltr/h, 35 mWs, motor 3 kW - 2.900 rpm - 380 V - 50 Hz., - CIP pump (P3), Tuchenhagen VPD 51, 110.000 ltr/h, 8 mWs, ...
Unused renovation kit for an Alfa Laval CPM Constant-Pressure Modulating Valve (CPMI-2) pneumatic regulating valve. Genuine Parts Service Kit CPMI - 2/XPMO - 2 Upper NBR, Lower EPDM/PTFE, part no. 9611920218., Type of Machine: Constant-Pressure Modulating Valve, Art. no.: 9611920218
Unused Alfa Laval ThinkTop V50 is a valve-top control unit that provides surveillance and control of valves during the fluid handling process. The control unit has been developed with user friendliness and robustness in mind. The V50 series is the compact option with a feature set tailored to valves that require only one solenoid valve such as butterfly and single seat valves. Solenoid valves 1 x 3/2. Digital 24 VDC. Article number: 9615400403., Type of Machine: Valve-top control unit, Art. no.: 9615400403
A Mercer APS Fluidbed Dryer is an industrial fluidized-bed drying system used to gently and efficiently remove moisture from particulate products such as powders, granules, flakes, or pellets. It operates by suspending the product in a controlled stream of heated air, creating a fluid-like behavior that maximizes heat and mass transfer. APS” typically refers to Advanced Processing System, highlighting enhanced control over airflow, temperature, residence time, and hygiene—features important in food, dairy, chemical, and pharmaceutical applications. Previously used in a Casein plant in New Zealand for tor R&D projects. Including Filterhouse, blower, Steam valves and GEA Nucon CV 500 Sanitary Rotary Valve / Airlock., Type of Machine: Fluidbed Dryer, Capacity: 150 kg/h, Product: Dairy products, Dimensions of the fluidbed: 255 x 100 cm, Dimensions: ± 4 x 1,5 x 2 mtr
The Alfa Laval SRU6/260/LS is a robust positive displacement lobe pump designed for the gentle and efficient handling of sensitive process fluids. Engineered in accordance with the most stringent hygienic design standards, the pump features fully validated and effective Cleaning-in-Place (CIP) capability. The SRU pump range is suitable for applications across the dairy, food, beverage, brewing, chemical, pharmaceutical, and home and personal care industries. Its smooth, low-shear pumping principle allows for the handling of products with a wide range of viscosities—from low to very high—including creams, gels, emulsions, aerated mixtures, and media containing delicate cells or organic solids in suspension. Products containing fragile solids, such as curd, can be transferred without damage due to the specially designed tri-lobe stainless steel rotors. The pump has a nominal displaceme ...
Indirect heated Thermisation unit previously used for the production of Creme fraiche 30% and mesophiles product 10%, but it can be used for all acidified + stabilized products. Skid mounted unit existing out of: Tubular Heat Exchangers (GEA Finnah A 544), level tank (200 liter), water pumps (4x Grundfos), flowmeter, valves for product and utilities, interconnecting piping, high pressure product pump (APV Gaulin, type Z4P-0,5BF serienr 96L34959, year 1996, capacity up to 4.000 liter per hour, motor 5,5 kW - 955 rpm - 400 V - 50 Hz) and the control panel with Siemens S5 PLC and Siemens Simatic OP37 operation panel. Current temperature program: creme fraiche: 35 - 51 - 71 - 40 - 29 °C or mesophiles: 25 - 55 - 75 - 40 - 23 - 10 °C. Maximum temperature possible: 85°C.Capacit y of the unit: currently set on 2.500 liter per hour but a ...
Serviced Continuous Butter Making Machine - CBM with a new control panel with simple controls. Output of 800 kg butter per hour sweet butter and 600 kg butter per hour cultured butter. Input of ± 1.600 liter of cultured or / and sweet cream per hour (35/42% fat, pH of ± 4,8 and infeed temperature ± 8 - 13 °C). Complete electric driven. Churning motor: 15 kW. Screw conveyor (kneading) motor: 5 kW. Butter milk pump: 3 kW. Feed pump: 3 kW. Vacuum pump: 1,5 kW. New control panel with simple controls with cream inlet temperature indictator, wash water inlet temperature indicator, output temperature indicator, emergency stop, main switch and all on/off buttons for the pumps., Type of Machine: Continuous Butter Making Machine (CBM), Capacity: 600 - 800 kg butter per hour (output), Motors: Churning: 15 kW and Kneading: 5 kW - 415 V - 50 Hz, Year of Major Service: 2024, Operating Hours: 0 h s ...
MultiWeigh MW 16 Head Combination Weigher – High Accuracy | Fully Complete | 2015, High speed machine with memory buckets, We offer this MultiWeigh MW 16-head combination weigher, manufactured by HD-Wiegetechnik Sondermaschinen GmbH (Germany). MultiWeigh is globally recognized for precision weighing technology, reliability, and long service life in the food processing industry., This machine is fully complete, in good working condition, and supplied including collecting chute, making it ready for immediate production use., Technical Specifications, - Manufacturer: MultiWeigh (HD-Wiegetechnik Sondermaschinen GmbH), - Machine Type: MW 16 2.01 57° 3 MIX, - Number of Weighing Heads: 16 with memory buckets (high speed), - Control System: IPC 511, - Scale Interval (d): 1.0 g, - Scale Interval (dw): 5.0 g, - Operating Temperature Range: 0 – 45 °C, - Year of Manufacture: 03 / 2015, - Certi ...
Proseal Fastpack F40, Manufacturer: Proseal, Model: Fastpack F40 with printer, Application: Top seal tray sealing only, Condition: Used – in good working condition, Description, The Proseal Fastpack F40 is a compact high-speed inline traysealer designed for reliable and consistent top sealing of pre-formed trays. This machine is widely used in the food industry and is known for its robust construction, hygienic design and stable performance in continuous production environments., Key Features, - Top seal traysealer, - Inline, high-capacity design, - Stainless steel construction, - Fast and easy tooling change, - PLC controlled with operator HMI, - Stable and reliable sealing quality, - Suitable for high-volume food production
Labeling machine for top and bottom, with a ZODIAC printer for the top labels.
Eagle Pro Pack 240 PRO – Advanced X-Ray Inspection for Packaged Products, The Eagle Pro Pack 240 PRO is a high-performance X-ray inspection system designed for maximum product safety, quality assurance, and production efficiency., Ideal for food, pet food, pharmaceutical, and consumer goods applications,, this system combines cutting-edge detection technology with robust industrial design., ---------------------------------------------------------------, Key Features & Benefits, - Reliable detection of foreign contaminants, even in dense or metallized packaging, - Multiple quality checks in a single inspection, - High inspection accuracy at high production speeds, - Hygienic, stainless-steel construction for demanding production environments, Technical Specifications, Inspection Area, - Maximum inspection width: up to 242 mm, - Maximum inspection height: up to 101 mm, - Conveyor width: ...
Multiweigh 20 heads weigher, - With horizontal vibratory feeders for fast products like frozen food or sweets/ nuts., - 20 heads, - Fully stainless steel rigidized material to prevent sticking., - With collection bucket for a faster more controllable workflow
Hitec, Z-Elevating conveyor belt., Dimensions in the photo album., More information on request.
