subcategories
(3rd category level)
Manufacturer:
(Category: 505)
GUILLOTINE REEL SLITTER 60 T, Working width 3.000 mm, Working height 2.000 mm, Cutting force 2x30 Ton., No.2 pumps 38+38 lt/min, volume 26,4+26,4 ccm, Speed up: 51 mm/sec, Speed down : (80 Bar) 31-15 mm/sec, Oil tank 255 lt., 15 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulic pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., Force: 60 T
GUILLOTINE REEL SLITTER 60 T, Working width 3.500 mm, Working height 850 mm, Cutting force 2x30 Ton., No.2 pumps 38+38 lt/min, volume 26,4+26,4 ccm, Speed up: 51 mm/sec, Speed down : (80 Bar) 31-15 mm/sec, Oil tank 255 lt., 15 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulic pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., Force: 60 T, installed power - used power in work: about 60-65% : 15
GUILLOTINE REEL SLITTER 60 T, Working width 3.000 mm, Working height 1250 mm, Cutting force 2x30 Ton., No.2 pumps 38+38 lt/min, volume 26,4+26,4 ccm, Speed up: 51 mm/sec, Speed down : (80 Bar) 31-15 mm/sec, Oil tank 255 lt., 15 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulic pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., Force: 60 T
GUILLOTINE REEL SLITTER 50 T, Working width 3000 mm, Working height 1500 mm, Cutting force 2x25 Ton., No.2 pumps 38+38 lt/min, volume 26,4+26,4 ccm, Speed up: 83 mm/sec, Speed down : (80 Bar) 20-41 mm/sec, Oil tank 255 lt., 15 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulic pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., Force: 50 T, installed power - used power in work: about 60-65% : 15
GUILLOTINE REEL SLITTER 50 T, constructed in sturdy painted steel,, Working width 3.000 mm, Working height 850 mm, Cutting force 2x25 Ton., No.2 pumps 38+38 lt/min, volume 26,4+26,4 ccm, Speed up: 83 mm/sec, Speed down : (80 Bar) 41-20 mm/sec, Oil tank 255 lt., 15 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulic pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., Force: 50 T
GUILLOTINE REEL SLITTER 50 T, Working width 2.500 mm, Working height 1.500 mm, Cutting force 2x25 Ton., No.2 pumps 38+38 lt/min, volume 26,4+26,4 ccm, Speed up: 51 mm/sec, Speed down : (80 Bar) 31-15 mm/sec, Oil tank 255 lt., 15 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulic pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., Force: 50 T
GUILLOTINE REEL SLITTER 35 T, Working width 2.500 mm, Working height 1.500 mm, Cutting force 2x17,5 Ton., No.2 pumps 30+30 lt/min, volume 21+21 ccm, Speed up: 84 mm/sec, Speed down : (80 Bar) 40-20 mm/sec, Oil tank 175 lt., 9 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydrauliC pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer.
An overbelt metal separator is used to remove ferrous contamination from chopped scraps, on the extraction belt from a shredder. We offer different solutions in size and power even for stainless steel., Just send us your requirements and we will send you a most cost-effective, targeted offer., An overbelt metal separator is the easiest way to remove ferrous contamination from scraps., This machine is a available in different sizes, with different magnetic forces, Constructed according to the Italian Top Quality Standards, This is an example :, OVERBELT MAGNETIC TAPE SEPARATOR TYPE R60-80E, - 800 mm wide at a distance of 200 mm from the belt, - Construction characteristics :, - permanent magnet in bipolar conformation with low-carbon iron structure made with Sr Ferrite permanent magnets with high magnetic induction and great coercive force (guaranteed magnetic field strength 20 years), - ...
CROSSED MIXING SYSTEM FOR PLASTIC MATERIALS, The system includes n.2 x 30.000 lt. (or bespoke) vertical mixers which fill each other through the endless screw conveyor., for each mixer :, total height approx 9.500 mm including transmission group, max diam. 2400 mm.(standard transport) - 2 x LKW for the whole system, constructed in painted electro-welded carbon steel., inner auger diam.350 mm., lower hopper with safety grid and sampling shutter, complete with anti-dust cover, mm.600×500, pulley and belt transmission, protected by carters, inspection doors with safety limits, cleaning hinged door with on bottom of cone for complete discharging, with safety opening, loading hopper with conveying screw, bottom discharging on the other mixer, side discharging pipe to big bag with valve mm.at 2.500 mm from ground, electric level indicator, paddle type, electric motor 22 kw, complete with cont ...
Our VERTICAL MIXER 5 to 30 m3 are used to blend different batches of one material and grant a more homogeneous quality within one lot., Please see our attached [PDF](drive.google/file/d/1kQKOuxvrbrpfSZBrVxh2jrXbJ7StrQMp/view?usp=d rive_link) and photos for different sizes availables., Another important task they are used for, is to complete cooling of materials after a heat related process, like regranulation or agglomeration, in order to avoid the possibility that materials, due to residual heat, clog into lumps., Our standard mixers for plastic materials are constructed in sturdy electro-welded steel, painted on the outer surface with an anti-rust layer and a protection coating. Installed in a sheltered, dry place they will perform at their best for years ., - inner auger diam.350 mm., - lower loading hopper with safety grid and sampling shutter, complete with anti-dust cover, mm.600 ...
QUICK WASHER for RIGID and SOFT PLASTICS, made in AISI304 stainless steel, low water consumption, can be used with hot water or mild detergents, for reground LDPE LLDPE HDPE film, rigid PE PP PVC PET PA ABS PS PC, 7,5 kw motor 400V 50/60Hz, inner auger 400 mm diam., length 3.000 mm., material and water are loaded from the bottom, material discharging is done from top, bearings are positioned outside the wet chamber, seals on the lower bearing to exclude any contact with water, auger speed is adjustable to change throughput rate 500 to 1.000 kg/h, throughput rate can be adjusted according to contamination and material, Low water consumption (depending on contamination) About 60 lt., The water can be mechanically filtered with a [water screening system](.germanplast.eu/listings/5003567-germanplast-vibrating-screen- for-water-powder-granule) (available separately) to be reused in the proces ...
Manufacturer LINDNER N O W A T R E D U C E D P R I C E Type Chain Extraction Belt 9.600 mm long With central chain transport and paddles Flat type on supports Constructed in sturdy steel 5 kw motor + gearbox Construction year 2013 500 mm.outer width 400 mm.inside width
Manufacturer: BRAMIDAN Model: 4-X 30 Year of Manufacture: 2008 Supply: 3X230/400 kW: 4.0 Kg: 1840 dB:
Slightly used, technically flawless! Control: Simatic Tank capacity: 700l 1x Coolant pump high pressure: Flow volume 30l/min / 50 bar 1x Coolant pump low pressure: Flow volume 80l/min / 3 bar Fleece width: 390mm Connection: Voltage: 3x400V+PE/50Hz Power: 7.5kW Rated Current: 15A Pre-fuse maximum: 50A Dimensions LxWxH: 1700 x 1400 x 2100 mm Total weight empty: 650kg
Eichinger 2041.10 waste box van; Volume 750L; Load capacity 300kg; tilting; on wheels. Waste box wagon Eichinger 2041.10; capacity 750L; lifting capacity 300kg; tiltable; with rolls.
ID3574 Monsuna AKS A4 year/Baujahr 2014 Tire washing system for commercial vehicles, Monsuna type AKS A4 series, including tank, control system, signaling system, and contact loop for automatic operation. The washing zone is fully galvanized. The water supply is fully integrated into the module frame. Passage zone: 4000 mm long x 3100 mm wide (clear passage width: 2900 mm). Weight: approx. 5,000 kg (2 washing modules, each with a capacity of 2,500 kg). Tank: 7000 mm long x 3000 mm wide. Weight (unfilled) approx. 3,560 kg. Tyre washing system for commercial vehicles Monsuna type AKS A4 incl. tank, control system, signalling system and contact loop for automatic operation, the washing zone is completely galvanised, water supply is completely integrated into the module frame, passage zone: 4000 mm long x 3100 mm wide (clear clearance width: 2900 mm), weight: approx. 5,000 kg (2 wash mod ...
Year of construction 2006 Chip conveyor belt Mobile substructure Delivery date: immediately Ref: BU250081A Price on request. We supply and install worldwide.
Vacumet High-Tech Waste Management System Demonstration machine as good as new Tank size: 142 litres Volume reduction: 50 - 70 % Body material: powder-coated steel Weight: 198 kg Degree of protection: IP 54 Connected loads: 230 V 50 Hz 1 kW Control: PLC Noise level: 60 db Tested / Safety: EN 60204 - VDE 0113 Dimensions: W: 920 x D: 750 x H: 780 mm kasu - vacumet is a modern machine for disinfecting the exhaust air and reducing waste. Vacuum and the introduction of an odour blocker neutralise unpleasant odours, trap bacteria and viruses and contain bacterial carry-over. Due to the subsequent sealing of the foil bags and flooding of the chamber with atmospheric pressure, a pressure of approx. 8,000 kg/m² acts on the PA/PE garbage bag, thus achieving an enormous volume reduction.
Rotor diameter: 260mm, rotor blades: 3, stator blades: 2, motor power: 7.5kW, throughput: approx. 250kg-400kg/h, machine dimensions X/Y/Z: approx. 1500mm/1000mm/1600mm, weight: approx. 1200kg. Documentation available. On-site inspection is possible.
Six (6) identical pneumatic knife-gate valves Watergates are available. Housing: stainless steel, valve blade: stainless steel, max. operating pressure: 4bar, medium temperature range: -35°C-120°C, machine length: approx. 1873mm, machine diameter: approx. 382mm, weight: approx. 280kg. Documentation available. On-site inspection is possible.
Motor power: 37kW, rotor diameter: 500mm, rotor width: 790mm, cross-section: approx. 500mm/790mm, stator blades: 2-row, rotor: 6 blades left and right. Including cyclone, pipes, blower, 3 sets of knives and sieves with a diameter of 6mm/8mm/10mm. Grinding capacity: 6 sieve: 150kg/h, 8 sieve: 300kg/h, 10 sieve: 400kg/h. Documentation available. On-site inspection is possible.
A Gross Apparatebau GmbH shredder, which was used in the wood industry, is available. Feed opening X/Y: 600mm/800mm, hopper volume: 0.6m³, rotor diameter: 252mm, rotor length: 600mm, rotor speed: 90rpm, drive power: 18.5kW, number of knives: 14, screen perforation: 10mm-40mm, suction nozzle diameter: 160mm, machine dimensions X/Y/Z: approx. 1800mm/1200mm/1650mm, weight: approx. 1300kg, operating hours: 4578h. Documentation available. On-site inspection is possible.
A Stummer bale opener is available for opening compressed fiber bales for subsequent feeding. Output basic PES: approx. 1100kg/h, feed conveyor belt length: 5000mm, machine dimensions X/Y/Z: approx. 3550mm/2400mm/3000mm, weight: approx. 5000kg, operating hours: approx. 10200h. On-site inspection is possible.
waste oil collecting tank: . filling capacity: 1000 Liter : . with level indicator: . Please note:The machine is dismantled and ready for loading. It is not possible to show it under power or make a video.Our offer includes already the best pictures. So we don’t have and won’t send additional pictures.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Manufacturer:Husmann Model: HL II 1622 Year of Manufacture: 2020 - Maximum RPM: 20 – 40 - Operating Voltage: 230V / 400V - Operating Pressure: 400 bar - Power: 330 kW - Permissible Total Weight: 22,000 kg - CE Certified Find more here - / Contact us at -
We offer for sale a complete set of Indutec industrial shredder model PM16/3, equipped with all its original components and accessories, ideal for intensive industrial use in the sectors of recycling, material shredding or industrial processing. ✅ General Features: Model: Indutec PM16/3 Type: Heavy Industrial Shredder, High Power Condition: Excellent condition, complete, with accessories and spare parts Total weight: Approximately 47,500 kg divided into two containers + base Composition of the set (ready to operate): First container – N° 128790 – 13,000 kg Engine: WEG 315 S/M – 150 kW – Gearbox: FLENDER B3 SV 11A – 118 kW – Pump: Neuman & Esser CCS 6-M – 0.25 kW – Neuman & Esser clocks: 1.1, 1.2, 1.3, 1.4 Separator Gasket Lubrication tank Mill flange Spare parts set: blade holder, bevel gear, pendulum shaft, body and heads, bolts Second contain ...
Noxon 2003 year 2003 decanter centrifuge with a flow rate of 800kg/h, 37 and 11 Kw motor, control panel and frequency regulator were changed in 2018. Last service of the machine 2020. Currently in operation will be dismantled at the end of May 2025;
Fabric sliders: o Various nominal diameters available o Versions: Mechanical and pneumatic o Robust and durable for industrial applications Knob: o Precise control of flow rates o Choice of mechanical or pneumatic Condition: Mint
MAGNETIC SEPARATORS, in form of overbelt plates,, grids, channels, stars, etc.
GERMANPLAST SRL
