fp 16 used for sale

Nail series: 34° paper collated Strip nails Wire diameter: 3.8-4.6 mm Nail length: 100-160 mm Working pressure: 5-8 bar Weight: 7.10 kg Magazine capacity: 72 nails + Paper collated Strip nails of 4.6 x 160 19200 piece (600 St / carton, 32 piece box, order No. 140037) Compressed air nail machine 1100 EUR, 19200 ships nails 640 EUR

Machine type MIG/MAG welding system Make Merkle Type RedMIG 1600 K Connection voltage 1 x 230 volts Setting range 25 - 160 amperes Switch-on time 30% ED at 160 amperes 60% ED at 130 amperes Current setting 7 switching stages Cooling transformer by built-in fan Cooling burner gas-cooled Design mobile compact system Wire feed 4-roll drive Hedging 16 Ampere Dimensions L x W x H 800 x 460 x 620 mm Weight 65 kg Age 12 months Condition workshop-tested, very good, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 157 G, 3 mtr. Long 1 piece ground cable 4 mtr long, 25 sqmm 1 piece pressure reducer argon with 2 pressure meters 1 roll welding wire, D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece glass 90 x 110 mm white 1 piece protective glass 90 x ...

Sartorius Stedim biotech BioWelder 16370 The BioWelder works with a thermal welding cycle that does not require laminar flow. In this welding process, the blade is kept sterile and endotoxin-free throughout the process. The inserted hoses are cut with a knife and then fused together by the device. The cycle process is fully automated and is only released after a full cycle. Various programmable holders make it possible to weld thermoplastic hoses of the same type (e.g. C-Flex, Sanipure, Pharmed) with diameters from 6.4 mm (1/4") to 19.0 mm (3/4"). Characteristics: Fully automatic operation Welds thermoplastic tubes up to 3/4 inch outer diameter Pre-installed settings for C-Flex, Raumedic FluiSoftTM, AdvantaPure, AdvantaFlex, Pharmed and Sanipure hoses True Thermal Weld offers exceptional strength Aseptic connection without laminar flow hood Data output by a print ...

Rotary vacuum pumps sliding & lubricated Number: 5 PCs Status: Rebuilt Warranty: 12 months Manufacturer: Busch Type: RA160D Voltage: 50/60 Hz 400V Motor power: 4KW Nominal: 160m ³/h Discharge pressure: 0,5hpa(mbar) Includes: user manual, parts list Delivery time: In stock; ready for operation

Due to a customer cancellation, we can offer you the following shelf gratings at a one-time special price. The scope of delivery includes: 01x inlaid shelf rack, new Year of construction: 2022 Internal designation: V suitable for stand depth: 1,100 mm Crossbeam support: 50 mm Material color: hot-dip galvanized Total width: 1,635 mm Total depth: 1,095 mm Clear span: 995 mm External mesh size: 68x68 mm Mesh size inside: 64x64 mm Support rod: 34|2.0 mm Weight: approx. 20.03 kg | Pcs. The shelves are suitable for a shelf depth of 1,100 mm Ideally suited for truss lengths of 3,300 mm / required number of pieces per pair of trusses: 2 pieces The price above is a unit price!

mytron 160 K CO2 Double Incubator The CO2 Incubator 160 / 160K provides the "in vitro" growing cell and tissue cultures with environmental conditions that are very close to the physiological values of the organism. Interior volume: approx. 160 l Weight: 70 kg Recirculating air circulation: by fan Cooling: Cooling unit Temperature display: Setpoint and actual value display Temperature range: 5 °C above room temperature to 70 °C Temperature range (cooled): +15°C to 70°C at 23°C ambient Temperature constancy: +/- 0.2 K temporal Humidity display: setpoint and actual value display Humidity range: >/=95 % Moisture resistance: +/- 2.5 % CO2 display: setpoint and actual value display CO2 range: 0% to 20% CO2 CO2 constancy: +/- 0.2 % CO2 CO2 recovery time: 1% CO2/min Power supply: 230 V, 50 Hz, 2 x 8 AT WxHxD= 130x85x70 cm More items new and used - you can find them i ...

Transfer press KRUPP PST-A 160 built in 1980. Technical data of the KRUPP PST-A 160 press: - nominal pressure: 160 tons - cutting force grade 1: 400 KN - force between stands: 1200 KN - number of working steps including cutting stage: 11 - distance between stands: 200 mm - slider stroke: 210 mm - drawing depth: 70 mm - range of jumps, infinitely adjustable: 15-75 / min. - production range of jumps with repeatability of its setting: 25-75 / min. - number of actuation movements: 15-25 / min. - a usable work resource for a jump in the range of 25-75 strokes per minute. : 20,000 J - maximum load on a single step: 500 KN - maximum load of a single step using inserts: 630 KN - maximum width of the tape: approx. 340 mm - maximum diameter of the cut: 120 mm - minimum diameter of the pattern: 30 mm - distance between stands: 2450 mm - height of tool building at the lower posi ...

mytron 160 K CO2 Double Incubator The CO2 Incubator 160 / 160K provides the "in vitro" growing cell and tissue cultures with environmental conditions that are very close to the physiological values of the organism. Interior volume: approx. 160 l Weight: 70 kg Recirculating air circulation: by fan Cooling: Cooling unit Temperature display: Setpoint and actual value display Temperature range: 5 °C above room temperature to 70 °C Temperature range (cooled): +15°C to 70°C at 23°C ambient Temperature constancy: +/- 0.2 K temporal Humidity display: setpoint and actual value display Humidity range: >/=95 % Moisture resistance: +/- 2.5 % CO2 display: setpoint and actual value display CO2 range: 0% to 20% CO2 CO2 constancy: +/- 0.2 % CO2 CO2 recovery time: 1% CO2/min Power supply: 230 V, 50 Hz, 2 x 8 AT WxHxD= 130x85x70 cm Buy incubators and other products at low pric ...

Dear's Sale, Complete engines MTU 16V4000M33F working condition Brgds info@kscege

Bandwidth of 50-500 mm Band thickness 0.8 3.6 mm Belt speed 5-40 m / min Feed rollers 2 PCs Richwalzen (80 mm) - 11 PCs Working direction optional

Double side labeler incl. round labelling function, built in year of 2019, capacity approx. 30-35 cycles / min. Label length 20-300 mm / label height 160 mm / container diameter 20-110 mm The price is EURO 24.500,--.

Pneumatic 2 finger parallel gripper, PGN+ 160-1-SD, Schunk, used tested Special price If you have a VAT number, we will gladly issue you an invoice without VAT. Used - top condition The part was purchased from a company's spare parts warehouse and is in very good and tested condition. Ensuring the function In order to ensure the functionality of the goods, the buyer must check the goods at the time of acceptance or put them into operation. In case of any defect, which is not the fault of the seller, the goods can be returned within 2 weeks. We will refund the buyer only the product price paid to us. For these goods we have to exclude warranty claims of the buyer for improvement, exchange, subsequent delivery or also for updating in case of digital components. Also excluded is the liability for direct and indirect consequential damages. Our terms and conditions apply, see  ...

Diosna spiral mixer SPV 160 AD with 2 telescopic boiler For up to 160kg dough per Pan Kneading tool made of stainless steel Includes two stainless steel bowls Timer with two watches Two speeds Friction wheel drive Condition: reconditioned; checked and cleaned

<b>Properties</b> Used belt of manufacturer TRANS standard <b>Technical data:</b> Mass of the belt conveyor Specification no.: U1009424-V0091 Nominal radius/inner radius: 600 mm Width: 900 mm Nominal angle/slope angle: 180Grad Strap type: KT96 Förderhöhendiff.: 500mm <b>Belt conveyors</b> The belt is ideal to dovetail machines or jobs in the picking zone and to optimize the internal process. Transportation can foster the belt conveyor sensitive and different-sized containers, boxes or other packaging and article units to the task or delivery point and, for example, also serves as a connecting route before or between production and Woodworking machines. Also enables efficient parts in operating and storage and is designed to promote significant flow rates and distances.

Qty. 1 Second-hand strip rolling mill plant Mfc.: Gautchi, Pechiney, Spidem, Stein Heurty SA, TECMO-HUNTER, ACHARD, WALDRICH Built: 1971, 1973, 1975 Modernisation in 1991 Strip width: 850 – 1600 mm Thickness Entry: 12 mm Exit: 0.3 mm Consist of: Qty. 2 Strip casting line 4-Hi rolling mill Qty. 2 Homogenisation furnaces Slitter Grinder Qty. 2 Coil cars

<b>Properties</b> Used belt of manufacturer TRANS standard <b>Technical data:</b> Mass of the belt Specification no.: U1009424-V0520 Nominal radius/inner radius: 600 mm Width: 900 mm Nominal angle/slope angle: 180Grad Strap type: KT96 <b>Belt conveyors</b> The belt is ideal to dovetail machines or jobs in the picking zone and to optimize the internal process. Transportation can foster the belt conveyor sensitive and different-sized containers, boxes or other packaging and article units to the task or delivery point and, for example, also serves as a connecting route before or between production and Woodworking machines. Also enables efficient parts in operating and storage and is designed to promote significant flow rates and distances.

Qty. 1 Second-hand vertical band saw Mfc.: Ermas Type: 8090 Built: 2003 Block before sawing Height: max. 500 mm Width: 340 – extendable to 500 mm Length: 340 – extendable to 500 mm Finished block dimensions: 380-500 x 150-160 x 150-160 mm – H x L x W Sawing band wheels (2) dia.: 1250 mm Band speed: 900 – 3500 m/min. Diamond coated sawing band: 41 x 1.3 x 8430 mm Blade motor power: 22 kW Blade tension: Hydraulic Lubrication: Water (closed circuit) Clamping: Hydraulic Cabin: Closed with automatic door Crops evacuation with manipulator: Hydraulic

MAX 20 X 1600

Manual hand table for printing on paper, cardboard, film, PVC, acrylic etc. Up to 10 cm in thickness With counterweight Printing table: External dimensions: L 2395 mm x W 1675 mm x H 800 mm plate: 1250 mm x 1740 mm 100 x 100 cm weight: 150 kg min screen: 50 x 50 mm maximum printing frame: 1100 x 1500 mm

We are looking urgently All diesel MTU 16V4000 generator or just motors to export Search for up to 6 plants in each execution

ALLMATIC LC 160/200

Qty. 1 Second-hand die cutter with flexo printing press Mfc.: M&M Mediterránea de Maquinaria Type: WRC 98 1150-1600/DISTENCO Built: 1999 Flexo printing press with 3 colours Capacity: 50,000 boxes in 1 shift Input material: cardboard of max. dimensions: 1,150 mm x 1,600 mm Output material: boxes (for pizza) Included in the scope: approximately 15 tools for different sizes of boxes New electronics The complete die cutter with flexo printer will require approximately loading on 2 trucks. The box production process is as follows: Ready-made cardboard formats are inserted into the machine, the machine prints up to 3 colours, cuts the box and sends it on with a conveyor and stacks it.

TO WHOM IT MAY CONCERN; WE VE 2 SETS COMPLETE WARTSILA DIESEL 16V25 ENGINES AT OUR STOCK. ENGINES ARE IN GOOD WORKING CONDATION. ENGINE CRANK SHAFTS HAS STANDART SIZE HARD MARKING ON IT. ENGINES READY TO INSPECTION AND READY TO TRANSPORT. PLS FIND ENGINES DETAILS ON BELOW TYPE 16V25 ENGINE SERIAL NO. 4062 & 4063 POWER 3230kW RATED SPEED 900 RPM RUNNING HRS 27402 & 24816 YOB 1997 IF YOU HAVE ANY FURTHER QUESTIONS PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba Best regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

RECON ---------------------------------------------------------------------- ------- Please note: we also have other various RECON parts of different manufacturers / types in stock. We are pleased to provide you with our current stock list. If you have any further questions do not hesitate to contact us

Hammer 16T-M2152-1pcs (136t) Hammer 10T-18KP-1pcs(104t) Hammer 5T-17KP- 1pcs (75ton) Hammer 3T-M213-1pcs(63T) Hammer 2T-M212-1pcs(40T)

Key data: 1320 KW, 1650 kVA

ENGINE: Cummins KTA50-GS8 FREQUENCY (HZ): 50 VOLTAGE (V): 400 GENERATOR POWER: 1650(kVA) / 1320(kW) ENGINE POWER: 1287(kW) CYLINDERS: 16 STARTING: ELECTRIC CONTROL SYSTEM: SELF-CONTROL FUEL TYPE: DIESEL COOLING: WATER-COOLED WEIGHT: 1100kg DIMENSIONS L/W/HEIGHT (MM): 680022503200 The engines are new, complete including control, diesel tank, exhaust and batteries. Network monitoring, grid feed-in Soundproofed Immediately ready for use. Control: Deep Sea Electronics (DSE) / ComAp Alternator: Leroy-Somer / Stamford Additional: Automatic Transfer Switch (ATS) 63A/100A ABB & Schneider Disconnectors GenCloud Connect with a phone or computer Single-phase valve 50°C-55°C Radiator External Diesel Tank Lubricating Oil Heater Water Heating Dispatch: Worldwide transport including unloading is possible for an extra charge To be able to quote an exact freight pri ...

Skoda W 160 H/NR CNC Travel x= 14.500mm (bed is for the travel 18,500mm) Travel Y= 3.150mm Travel Z= 1.600mm Travel W= 1.250mm Spindle diameter 160mm Machine with ball screw Many accessories available: CNC control Siemens SINUMERIC 850 Rotary table ISO 16 2.200 x 2.200mm, capacity 16 ton included Chip conweyor : 19.000 mm + 12.000 mm Floor plates

Process air cooler/ chiller/ chiller, air-cooled, Type: TAEevo Tech 161 P3 MTA S.p.A. TAEevo Tech 161 are air-cooled compact water chillers that are suitable for outdoor installation. Including crank pan heating, phase monitoring, buffer tank 255 ltr. and built-in P3 Circulating pump. Cooling capacity kW 38.6 Cold water temp. Exit/Entry (°C): 7 / 12 Volume flow (m³/h) 6.58 Available pump pressure (bar) 2.59 Ambient temperature (°C) 32, Refrigerant R 410A, Electrical data: Voltage V 400, frequency Hz 50, phases Ph 3, Max. power consumption (kW) 21 Max. current (A) 36 Starting Current Circuit (A) 204 Protection class: IP54 Dimensions: Length (mm) 1862, Width (mm) 761, Height (mm) 1437, Weight (kg) 666 Connection Rp 1 1/2" Serial No.: 2200401313 Year of construction 2023 Condition: Optical 2, Technically ok used (Technical changes and prior sale res ...

Process air cooler/ chiller/ chiller, air-cooled, Type: TAEevo Tech 161 P3 MTA S.p.A. TAEevo Tech 161 are air-cooled compact water chillers that are suitable for outdoor installation. Including crank pan heating, phase monitoring, buffer tank 255 ltr. and built-in P3 Circulating pump. Cooling capacity kW 38.6 Cold water temp. Exit/Entry (°C): 7 / 12 Volume flow (m³/h) 6.58 Available pump pressure (bar) 2.59 Ambient temperature (°C) 32, Refrigerant R 410A, Electrical data: Voltage V 400, frequency Hz 50, phases Ph 3, Max. power consumption (kW) 21 Max. current (A) 36 Starting Current Circuit (A) 204 Protection class: IP54 Dimensions: Length (mm) 1862, Width (mm) 761, Height (mm) 1437, Weight (kg) 666 Connection Rp 1 1/2" Serial No.: 2200401313 Year of construction 2023 Condition: Optical 2, Technically ok used (Technical changes and prior sale res ...

Storage tanks 19.160 liter outside marbled for wine, water, fruit juice, schnapps UNI-NIED Measurement and Weight: Total Height: 4600 mm Cyl. Height: 3600 mm Diameter: 1650 mm Weight: kg Material: V2A Surface: Outside marbled, inside 2B=IIIC Upper body: With dished bottom With thread connection Cylinder tank: With 1 manhole With zapf clape With level indicator with bar and scale Lower bottom: With dished bottom With outlet pipe pulled forward with butterfly valve With 6 feet Can be combined with 10.600 liter storage tanks (cat-no. EUBA18-0047).

Tip width/grinding length: 1000/1075 mm Gr. Grinding diameter: 250 mm Table swivel: +/- 8° Gr. Table longitudinal movement: 1210 mm Workpiece spindle stick swivel: 0 - 90° Spindle bore/cone: 38 mm/MK 5 Grinding spindle stick easily swivelling Hydr. Quick adjustment approx.: 50 mm Grinding wheel dimensions: 400 x 50 x 127 mm 2 grinding wheel speeds due to V-belt step disc Drive power: 3 kW Space requirement: 2900 x 2200 x 1750 mm Weight: approx. 3.5 t

Key data: 1320 KW, 1650 kVA, 400 V

ENGINE: Cummins KTA50-GS8 FREQUENCY (HZ): 50 VOLTAGE (V): 400 GENERATOR POWER: 1650(kVA) / 1320(kW) ENGINE POWER: 1287(kW) CYLINDERS: 16 STARTING: ELECTRIC CONTROL SYSTEM: SELF-CONTROL FUEL TYPE: DIESEL COOLING: WATER-COOLED WEIGHT: 1100kg DIMENSIONS L/W/HEIGHT (MM): 680022503200 The engines are new, complete including control, diesel tank, exhaust and batteries. Network monitoring, grid feed-in Soundproofed Immediately ready for use. Control: Deep Sea Electronics (DSE) / ComAp Alternator: Leroy-Somer / Stamford Additional: Automatic Transfer Switch (ATS) 63A/100A ABB & Schneider Disconnectors GenCloud Connect with a phone or computer Single-phase valve 50°C-55°C Radiator External Diesel Tank Lubricating Oil Heater Water Heating Dispatch: Worldwide transport including unloading is possible for an extra charge To be able to quote an exact freight price, please ...

Control SIEMENS Sinumerik 840D Specifications: Workspace - Max. rotation and turning diameter 2,000 mm - Max. turning height 2,000 mm - Face plate diameter 1,600 mm - Max. face plate load 11,200 kg - Chisel slide travel (vertical) 1,400 mm Smallest plunger diameter 330 mm Plunger cross-section 250 x 210 mm - Drive power of the main motor 71 kW - Crossbar adjustment 1,170 mm - Crossbeam support of central face plate to the right 1,170 mm - From the middle of the face plate to the left 25 mm Speed of faceplate: - Number of transmission stages 2 - 1 level 3.15-80 min-1 - 2 Level 12.5-315 min-1 - Lifter and support hydrostatically guided Feeds - X and Z 0.1 2000 mm/min - Rapid traverse X and Z 6,000 mm/min - Weight approx. 24,000 kg - Voltage 400 V 50 Hz - Connected load 175 kW - Space requirement L = 10,000 mm B = ...

Travel X-axis 9,500 mm Y-axis 4,100 mm Z-axis 950 mm W-axis 900 mm Main spindle speeds (infinitely adjustable): 3.15 - 1000 rpm Spindle motor power 58 kW Feed speed (infinitely adjustable): X-axis 0.1 - 9600 mm/min Y-axis 0.1 - 5600 mm/min Z-axis 0.1 - 5600 mm/min W-axis 0.1 - 5600 mm/min Accessories: Plate field: 6 x 4 m (CNC-controlled B- and V-axis) Table: 2 x 2 m (CNC-controlled B- and V-axis)

Key data: 1600 KW, 2000 kVA, 400 V

ENGINE: 4016TAG2A FREQUENCY (HZ): 50 POWER: 2000kVA / 1600(kW) CONTROL SYSTEM: DSE / ComAp FUEL TYPE: DIESEL COOLING: WATER-COOLED WEIGHT: 17274kg DIMENSIONS L/W/HEIGHT (MM): 750022002250 The engines are new, complete including control, diesel tank, exhaust and batteries. Network monitoring, grid feed-in Soundproofed Immediately ready for use. Control: Deep Sea Electronics (DSE) / ComAp Alternator: Leroy-Somer / Stamford Additional: Automatic Transfer Switch (ATS) 63A/100A ABB & Schneider Disconnectors GenCloud Connect with a phone or computer Single-phase valve 50°C-55°C Radiator External Diesel Tank Lubricating Oil Heater Water Heating Dispatch: Worldwide transport including unloading is possible for an extra charge To be able to quote an exact freight price, please send us an inquiry with your details and full address For more information or i ...

Used forklift Linde H 160 for sale – 16 tons capacity, diesel, built in 1999 We offer a used Linde H 160 forklift for sale, ideal for demanding industrial applications. Technical details: Manufacturer: Linde Model: H 160 Propulsion: Diesel engine Lifting capacity: 16 tons Year of Make: 1999 Equipment: Full cabin Accessories: Long forks This Linde H 160 forklift is particularly robust and reliable, which makes it perfect for transporting heavy loads. Thanks to the full cab, the truck offers optimum driving comfort and protection in all weather conditions. Condition: Used, but well maintained and ready to use. This Linde forklift is an economical choice for operations looking for a reliable material handling solution. Contact us now for more information or to view!

R&E Conveyor No 2618 Y.O.M. 1998 Width 2x 650 Length 16 m Curved, head approx. 6 m Good condition!

MTU 16V4000 M 90 A BANK Heat Exchangers Charge Air Coolers Intercoolers 2930-12-378-7717 5260981120

Standard cylinder with locking unit, DNC-125-500-PPV-A-KP, 163494, Festo, used Top Special price For your info - The current new discounted price of a similar product is € 1955 excl. VAT. If you have a VAT number, we will gladly issue you an invoice without VAT. Used - top condition The part was purchased from a company's spare parts warehouse, was only used for a very short time and is in very good condition. Standard cylinder with locking unit, DNC-125-500-PPV-A-KP, 163494, Festo, used-Top, consists of: - Standard cylinder DNC-125-PPV-A (current discounted new price € 419 excl. VAT) - Locking unit KPE-32 (current discounted new price € 1536 excl. VAT) - and a longer piston rod Ensuring the function In order to ensure the functionality of the goods, the buyer must check the goods at the time of acceptance or put them into operation. In case of any defect, wh ...

Linear drive, stroke 420mm, DGPL-80-420-PPV-A-KF-B, 161797, Festo, used tested Special price If you have a VAT number, we will gladly issue you an invoice without VAT. Used and tested! The part was purchased from a spare parts warehouse of a company, was tested by us and checked for leaks. Ensuring the function In order to ensure the functionality of the goods, the buyer must check the goods at the time of acceptance or put them into operation. In case of any defect, which is not the fault of the seller, the goods can be returned within 2 weeks. We will refund the buyer only the product price paid to us. For these goods we have to exclude warranty claims of the buyer for improvement, exchange, subsequent delivery or also for updating in case of digital components. Also excluded is the liability for direct and indirect consequential damages. Our terms and conditions appl ...

MTU 16V4000 M 90 B BANK Heat Exchangers Charge Air Coolers Intercoolers 2930-12-378-7720 5260981120

Manufacturer: Grundfos Number: 3 Model: NBE 65-160/173 A-F-A-BAQE Built: 2008 Rated flow current: 126.9 m3/h Nominal head: 33.4 m Speed: 2910 rpm Pressure: 16 bar Temperature range: 0-120 °C Power: 15 kW The pumps never went into operation after installation and are therefore virtually unused. Technical specifications and data sheets are available and will be sent on request. The pumps can be purchased individually as well as in the complete package.

Manufacturer: Grundfos Number: 3 Model: NBE 50-160/167 A-F-A-BAQE Built: 2008 Rated flow current: 87.4 m3/h Nominal head: 32.6 m Speed: 2900 rpm Pressure: 16 bar Temperature range: 0-120 °C Power: 11 kW The pumps never went into operation after installation and are therefore virtually unused. Technical specifications and data sheets are available and will be sent on request. The pumps can be purchased individually as well as in the complete package.

approx. 4x belt conveyors, transnorm, approx. 1m long – used - : Price per piece ex location (net): only 595.-€ incl. dismantling, packing and loading! Please note our other advertisements for this location resolution: A total of almost 90 positions of conveyor technology are available. including belt conveyors between 70cm and almost 4.50m in length, various belt curves, ejectors, inclined conveyors, as well as various folding storage boxes, picking trolleys, packaging machines, etc.! Pos1+2+21+22 Manufacturer: Transnorm Type: TS 1200 Belt Conveyor / Type: 1600-105 Year of Make: 1996 Element length: 100cm Element width: approx. 50cm Strap width: approx. 40cm Engine: SEW Condition: good Available now Location: CZ, Bor, later camp Frankenberg / Saxony

MTU 16V4000 M 90 A BANK 2930-12-378-7717 5260981120

MTU 16V4000 M 90 B BANK 2930-12-378-7720 5260981120

n1-n2= 50-6000 rpm without speed controller, without switch Dimensions LWH: 200 x 100 x 500 mm

Aerzener

Rolls-Royce Olympus SPEED SIGNAL GENERATOR from the stock of the Army Navy Unused or overhauled

Key data: 120 KW, 150 kVA, 400 V

Net price: 22.800,- € Gross price: €27,132.- - - - - - John Deere Emergency Power Generator Set 150 / 165 kVA - NEW + + with 950 litre large tank + + - - - - - Engine: - John Deere - Model: D6068 -Diesel - 1500 rpm - - - - - Generator: - Manufacturer: Leroy & Somer (France) - 150 / 165 kVA - 230 / 400 volts - 50 Hertz - AVR regulator - - - - - Control / Start Unit: - Digital ComAp Start Unit - Manual start at the touch of a button - Automatic start function - Generator monitoring: volts, amps, hertz, kW - Engine monitoring - Hour meter - Maintenance timer - - - - - Other data: - Dimensions: 330 x 110 cm - Weight: approx. 2060 kg - Tank volume: 950 litres large tank - - - - - Other: - An integrated socket package can be ordered for an extra charge - This is expected to include: 1x 400V 32A, 1x 400V 63A + 1x 400V 125A + RCD  ...