Manufacturer:
(Category: 107-632)
Key data: 3100 mm, 4 mm, 1000 mm
Hydraulic Shear SAGITA BEYELER 3100 x 4 mm Cutting length: 3100 mm Maxi thickness: 4 mm Electric Back gear gauge travel: 1000 mm Throat depth: 300 mm Year of construction: 1978 13 hydraulic sheet-metal clamps Blue electrical cabinet not used because it was used for the rear sheet metal conveyor There is a slight hydraulic leak at the left cylinder Supplied with a new replacement blade + front stop Voltage: 380 V Length: 3700 mm Depth: 2400 mm Height: 1500 mm Weight: approx 5 T
sheet width: 3100 mmplate thickness: 6.35 mmthickness at Niro-steel: 4.00 mmcutting angle: 0.5 - 2.5 °cutting gap adjustment: 0.05 - 0.8 mmno. of strokes: 12 - 50 Hub/minback stop - adjustable: 1000 mmControl: ELGO TYP 85 oil volume: 120 ltr.engine output: 13.0 kWweight: 6300 kg.range L-W-H: 3950 x 1950 x 1680 mm very well-maintained condition ()Equipment:- Electro-hydraulic guillotine shear with guided blade movement- ELGO NC Type 85 control unit Front control panel, swiveling (front left)- Electro-hydraulic cutting angle adjustment- Electro-hydraulic cutting gap adjustment- NC motorized backgauge With recirculating ball screws- 1x side gauge 2,000 mm ... with T-slot + mm scale- 2x front support arms 1,000 mm ... with mm scale- Recessed grips in the support table- Front finger guard- 1x movable foot pedal- Operating manualThe data for this ad was created with ModulMWS - the software so ...
Key data: 2540 mm, 1 mm, 500 mm
used Schechtl hand-held guillotine shears Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is being carried out Working length: 2540 mm Sheet thickness steel: 1.0 mm Sheet thickness aluminium: 1.5 mm Sheet thickness front: 0.6 mm Colour: green Machine weight: 860 kg Dimensions: 2942 x 1330 x 1500 mm Automatic hold-down Back gauge max. 500 mm Machine Number: 5360
: gebraucht : 1998 : 090148 : prompt, Zwischenverkauf v : Belgien : 22800 €: 1 : 3100 mm: 6 mm: 0.5 - 3.5 °: 9.5 kW: 950 mm: 4070 mm: 2330 mm: 3400 mm: 1850 mm: 5500 kgMotorized backgauge 1000 mm, ball screws, digital displayCutting gap adjustment from the front with handwheelCutting length adjusmentCutting angle adjustmentDownholer safety guardRear safety via light barrierFoot pedalTable supports with ball bearings1 side arm 1500 mm2 support armsOperating manual in German with CE declaration of conformityBUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISEWe offer you maximum security and complete transparency.• HONEST INSIGHTS: Detailed photos and functional videos of the current condition• LIVE ON-SITE CHECK: Live testing is possible at our facility• DIGITAL DEMONSTRATION: Individual live demonstration via video call• RISK-FREE PURCHASE: 14-day return polic ...
Key data: 3050 mm, 6 mm
Guillotine shears hydraulic Manufacturer: Atlantic Type: ATS3000 Year of Make: 1992 Sheet width: 3,050 mm Sheet thickness: 6.0 mm Sheet thickness for stainless steel: 4.0 mm Cutting angle: 0.5 - 3.0 ° Electro-motor backgauge 10-750 mm Engine power: 10.0 kW Weight approx.: 4.800 kg Dimensions L/W/H: 3,750 x 1,600 x 2,450 mm
used
: gebraucht : 1996 : 090232 : ca. 2 Wochen ab Auftragse : Türkei : 16900 €: 1 : 3100 mm: 6 mm: 19 1/min: 1.5 °: 14 : 1000 mm: 15 kW: 200 l: 3700 mm: 2250 mm: 2700 mm: 1830 mm: 5600 kgSwing-beam cutting designMotorized backgauge (1000 mm) with digital displayFootpedalCentral manual blade gap adjustmentCutting line illuminationWide support table with transfer balls1 side gauge with scale, T-slot, and flip-stop2 sheet support arms with T-slotsOil fillLight curtains at the rear of the machineTHE BLADES WERE GRINDEDOperating manual in German with EC Declaration of ConformityBUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISEWe offer you maximum security and complete transparency.• HONEST INSIGHTS: Detailed photos and functional videos of the current condition• LIVE ON-SITE CHECK: Live testing is possible at our facility• DIGITAL DEMONSTRATION: Individual live demon ...
Key data: 3050 mm, 20 mm, 800 mm
Hydraulic Sheet Metal Shear / Hydraulic Guillotine Shear Make: Steiner Type: HTS 30/20 Year of manufacture 1978 -Cutting length: 3050 mm -Cutting thickness: 20 mm -Back gauge: 800 mm, via handwheel - Motor power: approx. 30 Kw -Spare blade Basic machine: 4650 mm long, 2610 mm wide, 3200 mm high Weight: approx. 27,000 kg -Mechanical, in good condition- -Optical, in good condition- Hydraulics leak slightly no guarantee, no return, no warranty Machine is still in commercial use and can be viewed by appointment. Transport from the hall and removal is carried out by the buyer and at his expense
sheet width: 1040 mmplate thickness: 6,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 3,50 tdimensions of the machine ca.: mMotorized 2-speed backgauge with digital display up to 1000 mmSide gauge and table extensionsCutting length limiterCutting edge illuminationSharpened bladesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 26300 Technical data: - max. working width 3050 mm - max. cutting capacity St 40 12 mm - Cutting angle adjustable mot. 0,5 - 3 ° - Cutting gap adjustment by hand - Number of hydraulic hold-downs 18 pcs - Mot. Back gauge 10 - 1000 mm - Front angle stop - Stroke rate depending on cutting angle and cutting length 7 - 17 rpm - Hydraulic drive 400 V / 22.5 kW - Table height 770 mm - Space requirement approx. W 4100 x H 2030 x D 2030 mm - Weight approx. 8500 kg - with: - E. foot switch - Cut line illumination
sheet width: 2540 mmplate thickness: 6,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: ca. 5,50 tdimensions of the machine ca.: mMotorized backgauge (2 speeds) up to 1000 mm with analog displaySide gauge and table extensionsCutting length limiterCutting line illuminationSharpened bladeThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 26307 Technical data: - max. working width 3050 mm - max. cutting capacity St 40 6 mm - Cutting angle adjustable mot. 0,5 - 3 ° - Cutting gap adjustment by hand - Number of hydraulic hold-downs 18 pcs - Mot. - Back gauge 10 - 750 mm - Front angle stop + support arms - Stroke rate depending on cutting angle and cutting length 9 - 17 rpm - Hydraulic drive 400 V / 7.5 kW - Table height 770 mm - Space required including back gauge, without front support arms - approx. W 3750 x H 1600 x D 1650 mm - Weight approx. 4500 kg - with: - E. - Foot - Switch - Cut line illumination
sheet width: 1040 mmplate thickness: 2,50 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: ca. 0,900 tdimensions of the machine ca.: mMotorized backgauge up to 750 mmPneumatic sheet supportCutting gap adjustmentSide gaugeSharpened bladesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 26238 Technical data: - Max. working width 3190 mm - Max. material thickness at 40 kg/mm², strength 6.3 mm - Cutting angle 1.2 ° - CNC - Cutting gap adjustment - Strokes 30 to 64 1/min - Stand projection 100 mm - Table height approx. 800 mm - Number of hold-downs 16 pcs - Back gauge 5 - 1000 mm - 3 pieces front support arms 1500 mm - E – Footswitch - Rear tilting roller table - Drive 400 V / 18.5 kW - Space requirement approx. W 3900 x H 1800 x D 2100 mm - Weight approx. 6800 kg - with : - CNC control RAS system - Rear tilting roller table / sheet metal hold-up - Rollable material collection container - Electronic rear space protection / light barrier
sheet width: 1040 mmplate thickness: 2,50 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 0,800 tdimensions of the machine ca.: mManual backgauge, adjustable from the front up to 550 mmSharpened bladeThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 26220 Technical data: - Cutting length 3050 mm - Cutting thickness at 400 N/mm² strength 16 mm - Cutting thickness at 400 N/mm², strength up to 1000 mm, length 18 mm - Cutting angle 0.5 - 3 ° - Number of sheet hold-downs 18 pcs - Stroke rate 10 - 23 min - Mot. Back gauge up to 1000 mm - Rear area protection with light barrier - Front angle stop 1000 mm - HSLX version: - CNC control HACO SC 5 controller when entering the sheet thickness in mm - Autom. Cutting angle adjustment according to sheet thickness - Cutting length limitation - Autom. Positioning of the backgauge (8 programs – 80 sets) with - Digital display and autom. Backgauge retraction - Drive 400 V / 22 kW - E - Footswitch - Space requirement without support arms approx. W 4500 x H 2250 x D 2200 mm - Weight approx. 14500 kg
sheet width: 6020 mmplate thickness: 6.0 mmthickness at Niro-steel: 4.0 mmback stop - adjustable: max. 1000 mmwork height max.: 1030 mmno. of strokes: 5 - 10 Hub/mincutting angle: 0.5 - 3.0 °down holder: 33 StückControl: SC 100 T engine output: 11.0 kWweight of the machine ca.: ca. 27000 kgrange L-W-H: 7650 x 2400 x 2885 mm New price in 2021 ~ 160.000 Euro Special price upon request- in checked conditions - machinevideo - https://www.youtube.com/watch?v=qH3uqGNZZp8Equipment:- Robust electro-hydraulic guillotine shear Design: Guide rail- HACO CNC control model SC 100 T, pivoting at the front left Control unit with LCD display Pre-selected positioning of the backgauge Digital display of actual position Electro-hydraulic cutting angle adjustment Electro-hydraulic cutting gap adjustment Programmable retraction from the backgauge Programmable cutting length limitation Automatic + manual pr ...
Offer 26181 Technical data: - max. working width 2540 mm - max. cutting capacity St 40 10 mm - Cutting angle adjustable mot. 0,5 - 3 ° - Cutting gap adjustment by hand - Number of hydraulic hold-downs 15 pcs - Mot. – Back gauge with positioning control 10 - 1000 mm - Front angle stop - Stroke rate depending on cutting angle and cutting length 7 - 17 rpm - Hydraulic drive 400 V / 15 kW - Table height 770 mm - Space requirement approx. W 4100 x H 2030 x D 2030 mm - Weight approx. 7500 kg - with: - E-foot switch - Cut line illumination
used
: gebraucht : 2015 : 090243 : prompt, Zwischenverkauf v : Türkei : 21800 €: 3100 mm: 6 mm: 4 mm: 15 1/min: 1.5 °: 1000 mm: 15 kW: 200 l: 4110 mm: 2200 mm: 3790 mm: 2100 mm: 7300 kgMIT PNEUMATISCHER BLECHHOCHHALTEVORRICHTUNGSchwingschnittausführungNC-Vorwahlsteuerung D-Touch 7 mit Touch-Screen für Hinteranschlag, Schnittlänge, Stückzahl, USB AnschlussMotorischer Hinteranschlagbis 1.000 mm auf Kugelumlaufspindeln, hochklappbarÜbersichtliches Bedienpult aufSchwenkarm montiertHydraulische Niederhalter nahe an derSchnittkante angeordnetFußschalterZentrale manuelle SchnittspaltverstellungSchnittlinienbeleuchtungBreiter Auflagetisch mit GleitkugelnStückzählerEinzel- und DauerhubHochklappbarer Fingerschutz 1.000 mm1 Seitenanschlag 1.500 mm mit Skala,T-Nut und Kippnocke2 Blechauflagearme 1.000 mm mit T-NutEinfaches Wechseln und Nachschleifender MesserEinstellbare Schnittlänge fürwir ...
Offer 23220 Technical data: - max. working width 3050 mm - max. cutting capacity St 40 6 mm - Cutting angle hydr. adjustable 0.3 - 3 ° - Cutting gap adjustment by hand - Number of hydraulic hold-downs 17 pcs - Engine backgauge 20 - 700 mm - Front angle stop + support arms - Stroke rate depending on cutting angle and cutting length 7 - 17 rpm - Hydraulic drive 400 V / 15 kW - Table height approx. 900 mm - Space required including back gauge, without front support arms - approx. W 3700 x H 1850 x D 2250 mm - Weight approx. 5800 kg - with: - E-foot switch - Cutting line illumination - - Cutting length preselection via potentiometer - Rear of the machine with light barrier safety
: gebraucht : 2002 : 090129 : prompt, Zwischenverkauf v : Türkei : 27800 €: 1 : 3100 mm: 10 mm: 350 mm: 10 1/min: 1.5 °: 1000 mm: 22 kW: 3800 mm: 3600 mm: 2000 mm: 9800 kgSwing cut constructionNC-preselection system ENC100 for back gauge, cutting length and piece counterMotorized back gauge 1000 mm on ball screws, folding upwardsHydraulic hold down pistonsFoot switchCentral, manual blade gap adjustmentCutting line illuminationBroad table with ballsFold up finger guard 1.000 mm1 squaring arm 1. 500 mm with scale,T-slot and tilting cam2 supporting arms 1.000 mm with T-slotOilfillingLight barrier on the back of the machineUser manual in GERMAN with EC declaration of conformityBUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISEWe offer you maximum security and complete transparency.• HONEST INSIGHTS: Detailed photos and functional videos of the current condition• LI ...
Key data: 2540 mm, 6 mm
Max. cutting length: 2540 mm Max. sheet thickness: 6 mm steel Motorized adjustable back gauge (2 speeds) up to 1000 mm with analogue display Side stop and table extensions Cutting length limitation Cut edge lighting Knife sharpened Weight approx. 5500 kg
: gebraucht : 1992 : 090174 : Belgien : 17800 €: 1 : 3050 mm: 6 mm: 11 - 25 1/min: 0.5 - 3 °: 18 : 750 mm: 11 kW: 3850 mm: 1750 mm: 1720 mm: 4600 kg: 770 mmSC 5 control for:- Sheet thickness input- Automatic cutting angle and gap adjustment- Cutting length limitation- Programmable backgauge lengthMotorized backgauge 750 mmDownholder protection guardFoot pedalTable supports with ball bearings1 side fence 1000 mmOperating manual in GermanMachine does not comply with German accident prevention regulations (UVV) or Austrian AMVONEW BLADESBUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISEWe offer you maximum security and complete transparency.• HONEST INSIGHTS: Detailed photos and functional videos of the current condition• LIVE ON-SITE CHECK: Live testing is possible at our facility• DIGITAL DEMONSTRATION: Individual live demonstration via video call• RISK-FREE ...
Key data: 3000 mm, 6 mm
The dimensions of the machine are LxWxH 2000mm x 3800mm x 1400mm. The weight is approx. 3500kg. The machine is in a little-used condition.
sheet width: 3050 mmplate thickness: 6,5 mmdistance between columns: 3100 mm: 1000 mmCutting length: variabel mmcutting gap adjustment: variabel mmconnected load: 12,0 kWweight of the machine ca.: 5,5 tdimensions of the machine ca.: 3,5 x 2,2 x 1,8 mHydraulic guillotine shear with- cutting length adjustment- cutting angle adjustment- support arms- squaring arm- rear enclosure- mobile material binThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 3100 mm, 6 mm, 1000 mm
Hydraulic Guillotine Shear HACO TS 3006 Capacity: 3100 x 6,5 mm Back gear gauge travel: 1000 mm Year of construction: 2002 Motor power: 7,5 kW SP8 Command Blades with 4 cutting edges Voltage: 380 V Photocells at the back Length: 4000 mm Depth with photocells : 2800 mm Depth without photocells: 2200 mm Height: 1900 mm Weight: approx 5 T
sheet width: 3100 mmplate thickness: 4.0 mmthickness at Niro-steel: 2.5 mmcutting angle adjustment: 1.0 °back stop - adjustable: 10 - 1000 mmadjustment speed: 180 mm/sdown holder: 21 Stückstrokes per minute: 18 - 31 column arm: 200 mmControl: ELGO P8721 oil volume: 160 L0: max. 300 barvoltage: 400 Vmain drive: 7.5 kWweight of the machine ca.: 4800 kg.dimensions of the machine ca.: 3660 x 2070 x 2140 mm from a maintenance workshop good condition ()Features:- Electro-hydraulic sheet metal shear (swing cut)- Machine frame = all-steel welded construction - ELGO NC control system, Model P8721, control panel on the front left for positioning the electrically driven backgauge Target/actual position value input possible Adjustment via three-phase motor using a toothed belt- Support table with ball bearings Recessed handles between the table plates- Front finger guard- Hydraulic sheet metal hol ...
Key data: 1250 mm, 4 mm
Max. cutting length: 1250 mm Max. sheet thickness: 4 mm steel Controlled backgauge Side stop and table extensions Cutting length limitation Cut edge lighting Light barrier to protect the rear area Knife sharpened Weight approx. 2800 kg
LARA SHEAR CDCH-1400 (year 2018) With a tow table. Hydraulic shear designed for the cross-cutting of strip and management of sheet metal surplus in coil feeding lines. It is supplied together with a feed table, allowing a comfortable and safe evacuation of the cut material and maintaining a clean and continuous production process. Robust equipment, of heavy industrial construction, especially suitable as auxiliary equipment in cutting, stamping or coil feeding lines. Work materials -Carbon steel -Stainless steel -Aluminum and light alloys Main technical data - Maximum working width: up to 1,400 mm -Drive type: hydraulic -Working pressure: 4–6 bar (pneumatic control system) -Power supply: 400 V / 50 Hz
sheet width: 2540 mmplate thickness: 2,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 1,60 tdimensions of the machine ca.: mManual backgauge up to 550 mmSide gauge and table extensionsSharpened bladesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Technical data: - Max. cutting width 2080 mm - Max. cutting capacity at 45 Kp/mm² 6 mm - Column projection 150 mm - Automatic cutting angle adjustment 0.3 - 2 ° - automatic. Cutting gap adjustment - Number of hold-downs 10 pcs - Stroke rate up to 22 1/min - Front angle stop approx. - 2 pcs. front support arms approx. - mot. Back gauge with positioning control up to 1000 mm - Rear space protection with light barrier - Cut line illumination - Working height 860 mm - E - Footswitch - Drive 400 V / 11 kW - Space requirement approx. W 3150 x H 2150 x D 2300 mm - Weight approx. 4.8 t
sheet width: 6080 mmplate thickness: 6.0 mmrear stop: 1000 mmcutting angle: 0.5 - 2.0 °down holder: 29 Stkno. of strokes: ca. 10 Hub/mintotal power requirement: 22.0 kWdimensions of the machine ca.: 7300 x 2150 x 2750 mmweight: 25500 kg Current list price: approx. 150.000 eurosFeatures:- Electro-hydraulic, slide-guided sheet metal shear- Electro-hydraulic cutting angle adjustment- Electro-hydraulic cutting gap adjustment- Electrically driven backgauge with ball screws- Manual central lubrication- Cut line illumination- Ball bearings in the table- Fold-up finger guard, 1.000 mm- Side stop with T-slots, tilting stop, and scale- 5 support arms with T-slots- Photoelectric sensors on the rear of the machine- 1 freely movable foot switch Includes optional equipment:- Pneumatic sheet metal holding deviceThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 3140 mm, 1 mm
new Schechtl motorized guillotine shears, with the following equipment: - within the EU: 32 amp connection plug with 5 m cable - 1 pair of steel scissor knives (single-edged) - Manual depth stop 0-750 mm with pneumatically operated tilting table, Laying down to the front - Support plates with 10 mm graduation and tape measure - Footswitch - Three-sided safety cage around the depth stop - Compressed air must be available: min. 6 bar, max. 10 bar - approx. 50 l/min - Cut-gap illumination - Electronic position display - Contact stroke counter tico 731.3 - Sheet metal stacking trolley light max, load capacity 300 kg Working length 3140 mm 20 Sheet thickness steel 1.5 mm 30 Sheet thickness Alu 2.25 mm 40 Blechdicke VA/Sheet thickness stainless 1,0 mm 50 Maschinennummer/Machine number MT 13952 Working length: 3140 mm Sheet thickness steel: 1.5 mm Sheet thickness alumi ...
: neu : ca. 10 Wochen ab Auftrags : Türkei : 59600 €: 1126.44 €: 3100 mm: 10 mm: 6 mm: 50 mm: 13 1/min: 1.5 °: 16 : 22 to: 1000 mm: 200 mm/s: 22 kW: 200 l: 2 Stk.: 865 mm: 580 mm: 3515 mm: 4200 mm: 2250 mm: 3600 mm: 2100 mm: 9300 kgSwing cut constructionNC-preselection system D-touch 7 with touch screen for back gauge, cutting length, quantity, USB portMotorized back gauge 1000 mm on ball screws, folding upwardsClear control panel mounted on moveablearmHydraulic hold down pistons are arrangedclose to the cutting edgeFoot switchCentral, manual blade gap adjustmentCutting line illuminationBroad table with ballsPiece counterSingle and continous stokeFold up finger guard 1.000 mm1 squaring arm 1. 500 mm with scale,T-slot and tilting cam2 supporting arms 1.000 mm with T-slotSimple replacement and grinding of thebladesVariable adjustable cuttinglength for economic processingLower blade f ...
: neu : ca. 10 Wochen ab Auftrags : Türkei : 68700 €: 1298.43 €: 3100 mm: 13 mm: 8 mm: 50 mm: 13 1/min: 1.75 °: 16 : 37 to: 1000 mm: 200 mm/s: 30 kW: 330 l: 2 Stk.: 840 mm: 600 mm: 3550 mm: 4280 mm: 2300 mm: 3600 mm: 2350 mm: 12500 kgSwing cut constructionNC-preselection system D-touch 7 with touch screen for back gauge, cutting length, quantity, USB portMotorized back gauge 1000 mm on ball screws, folding upwardsClear control panel mounted on moveablearmHydraulic hold down pistons are arrangedclose to the cutting edgeFoot switchCentral, manual blade gap adjustmentCutting line illuminationBroad table with ballsPiece counterSingle and continous stokeFold up finger guard 1.000 mm1 squaring arm 1. 500 mm with scale,T-slot and tilting cam2 supporting arms 1.000 mm with T-slotSimple replacement and grinding of thebladesVariable adjustable cuttinglength for economic processingLower blade ...
Key data: 4100 mm, 6 mm
Capacity: 4000 x 6 mm. Stroke 120 mm. DURMA DT-7 Control. Serial No. 608922260. Dimensions: 5230 x 3600 mm. Height 2150 mm. Weight 11460 Kg
sheet width: 3050 mmplate thickness: 4 mmweight of the machine ca.: 6.500 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 3000 mm, 10 mm
Hydraulic guillotine shears - ordering machine (delivery time approx. 10-14 weeks) - incl. foot switch, touch screen, rear installation room with light barrier monitoring, cutting gap automatic/electric, cutting angle automatic/electric, hydraulic hold-down device, mot. Back gauge up to 1000 mm depth -Similar to illustrations- Hydraulic plate shear - order machine (delivery time approx. 10-14 weeks) - incl. foot switch, touchscreen, rear set-up area with light barrier monitoring, automatic/electrical cutting gap, automatic/electrical cutting angle, hydraulic hold-down, mot. backgauge up to 1000 mm -images similar-
sheet width: 2050 mmplate thickness: 6.0 mmthickness at Niro-steel: 4.0 mmdistance between columns: 2100 mmdown holder: 12 Stückno. of strokes: max. 26 Hub/mincutting angle: 1.6 °back stop - adjustable: 750 mmControl: ELGO oil volume: 120 ltr.total power requirement: 11.0 kWweight: 3900 kgrange L-W-H: 2860 x 2100 x 1560 mm with only approx. 400 operating hours () Original price approx. 30.000 euros Special price upon request Features:- Robust electro-hydraulic oscillating shear- ELGO digital display, Model P9521, for electric backgauge- NC-controlled electric motor-driven material/backgauge Travel range continuously adjustable backgauge X = 750 mm Backgauge with backlash-free ball screw Travel speed: 100 mm/sec- 1x sturdy side stop with T-slot and millimeter scale- 1x sturdy support arm - Electric cut length limiter Cut length limiter to increase the number of strokes per minute- Man ...
Offer 25500 Specifications: - Cutting length 3050 mm - Cutting thickness at 400 N/mm², strength 13 mm - Cutting thickness at 400 N/mm², strength up to 1000 mm, length 15 mm - Cutting angle 0.5 - 3 ° - Number of sheet hold-downs 18 pcs - Stroke rate 10 - 23 min -Mot. Back gauge up to 1000 mm - Rear area protection with light barrier - Front angle stop 1000 mm - HSLX version: - CNC control HACO SC 5 controller when entering the sheet thickness in mm -Auto. Cutting angle adjustment according to sheet thickness - Cutting length limitation -Auto. Positioning of the backgauge (8 programs – 80 sets) with - Digital display and autom. Backgauge retraction - Possibility of mot. Adjustment of the backgauge by 2 push buttons - Drive 400 V / 22 kW - E - Footswitch - Space requirement without support arms approx. W 4200 x H 2250 x D 2200 mm - ...
: neu : 2025 : 090132 : prompt, Zwischenverkauf v : Türkei : 47500 €: 798.38 €: 1 : 41800 €: 3100 mm: 6 mm: 4 mm: 50 mm: 15 1/min: 1.5 °: 16 : 14 to: 1000 mm: 200 mm/s: 15 kW: 200 l: 2 Stk.: 865 mm: 500 mm: 3515 mm: 4110 mm: 2200 mm: 3700 mm: 2100 mm: 7300 kgSwing cut constructionNC-preselection system D-touch 7 with touch screen for back gauge, cutting length, quantity, USB portMotorized back gauge 1000 mm on ball screws, folding upwardsClear control panel mounted on moveablearmHydraulic hold down pistons are arrangedclose to the cutting edgeFoot switchCentral, manual blade gap adjustmentCutting line illuminationBroad table with ballsPiece counterSingle and continous stokeFold up finger guard 1.000 mm1 squaring arm 1. 500 mm with scale,T-slot and tilting cam2 supporting arms 1.000 mm with T-slotSimple replacement and grinding of thebladesVariable adjustable cuttinglength for eco ...
Max. cutting length: 3050 mm Max. sheet thickness: 6 mm steel Controlled backgauge up to 1000 mm Side stop and table extensions Cut edge lighting Hydraulic shear angle adjustment Knife sharpened Weight approx. 6500 kg
sheet width: 4050 mmplate thickness: 8 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 3100 mm, 16 mm
- Year of construction 2001 Specifications - Cutting length: 3100 mm - Capacity: 16 mm - Stroke: 170 mm - Stroke rate: 10 /min - Oil tank: 410 l - Engine power: 37 kW - Operating voltage: 400 V - Rated current: 72 A - Rated current main fuse: 100 A - Dimensions WxHxD: 3750 x 2400 x 3425 mm - Weight: 13800 kg
sheet width: 3100 mmplate thickness: 6.35 mmthickness at Niro-steel: 4.00 mmcutting angle: 0.5 - 2.5 °cutting gap adjustment: 0.05 - 0.8 mmno. of strokes: 12 - 50 Hub/minback stop - adjustable: 1000 mmControl: DELEM DAC 360 oil volume: 120 ltr.engine output: 9.5 kWweight: 7000 kg.range L-W-H: 3950 x 1950 x 1680 mm well-maintained condition () equipped with new DELEM control unitEquipment:- electro-hydraulic, guided plate shear- DELEM CNC control unit type DAC 360 front control panel, swiveling front left- Electro-hydraulic cutting angle adjustment- Electro-hydraulic cutting gap adjustment- electro-motorized backgauge, with ball screws- 1x extra-long side fence with T-slot mm scaleThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 3190 mm, 6 mm
Note: Machine is currently still being revised, the illustrations were made before the Revision. Sheet width: 3190 mm Sheet thickness steel: 6.3 mm Colour: grey Total power requirement: 18.5 kW Machine weight: 6800 kg Dimensions: 3830 x 3820 mm with cutting gap adjustment Stroke rates per minute: 30 - 50 strokes/min Angle stop: 1500 mm Throat: 5 - 1000 (1500) mm
sheet width: 3000 mmplate thickness: 4 mmdistance between columns: 3050 mmtotal power requirement: 8 kWweight of the machine ca.: 4.8 trequired space: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Max. cutting length: 3100 mm Max. sheet thickness: 6 mm at 490 N/mm² Motorized backgauge with digital display Manual cutting gap adjustment Cutting length variably adjustable Cut edge lighting New knives
sheet width: 3100 mmplate thickness: 2 mmrear stop: 1000 mmcutting angle: 1°06 °no. of strokes: 45 Hub/mintotal power requirement: 3,0 kWdimensions of the machine ca.: 3600 x 2200 x 1600 mmweight: 4500 kgEquipment:- Electric motorized backgauge- With digital ELGO position display- Manual cutting gap adjustment- 1x side stop with mm scale- 2x support arms- 1x freely movable double foot switch- Front finger guardSpecial accessories included:- Pneumatic sheet metal holding device for thin sheet metal cutsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
