Offer 26238 Technical data: - Max. working width 3190 mm - Max. material thickness at 40 kg/mm², strength 6.3 mm - Cutting angle 1.2 ° - CNC - Cutting gap adjustment - Strokes 30 to 64 1/min - Stand projection 100 mm - Table height approx. 800 mm - Number of hold-downs 16 pcs - Back gauge 5 - 1000 mm - 3 pieces front support arms 1500 mm - E – Footswitch - Rear tilting roller table - Drive 400 V / 18.5 kW - Space requirement approx. W 3900 x H 1800 x D 2100 mm - Weight approx. 6800 kg - with : - CNC control RAS system - Rear tilting roller table / sheet metal hold-up - Rollable material collection container - Electronic rear space protection / light barrier
Key data: 1020 mm, 1 mm
used RAS 3-roll round bending machine, with wire inserts, seam groove, transmission gear, Adjustment of the rear roller from the front with scale, Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length 1020 mm Sheet thickness max. steel 1.25 mm Farbe/Colour grün Weight/Weight 150 kg Dimensions 1300 x 600 x 1100 mm Number of round rollers 3 pieces Roller diameter 56 mm Machine number: 316/10
Key data: 2540 mm, 2 mm
Max. bending length: 2540 mm Max. sheet thickness: 2.5 mm steel Motor-controlled back gauge with folding cams up to 1500 mm Multiple program sequences with different bending angles and lifting heights possible Multibend 2000 controller Bending rail ground Weight: 1,700 kg
Offer 26153 Technical data: - Max. projection 200 mm - Roller center distance 50 mm - Max. material thickness at 40 kg/mm² strength 1.25 mm - Space requirement approx. W 300 x H 1150 x D 500 mm - Weight approx. 25 kg - Various corrugated rollers
Max. cutting length: 2540 mm Max. sheet thickness: 2 mm steel Manual back gauge up to 550 mm side stop and table extensions Knife sharpened 1600 kg
Large working width: 4000 mm for sheet metal with a strength of 40 kg up to: 3 mm Table width: 470 mm Back gauge adjustment: 1000 mm Fixed cutting angle: 1°30' Column projection: 200 mm Hydraulic drive: 380 V, 7.5 kW Space requirement: 4650 x 1830 x 1420 mm high Weight: 5.7 t
Offer 26091 Technical data: - Max. working width 3200 mm - max. material thickness at 40 kp / mm² strength 2.5 mm - Bending angle adjustment electronically pre-selectable 0 - 180 ° - Operation via hand or foot switch - Largest opening width / stroke of the upper beam 200 mm - Height adjustability - bending beam 80 mm - the lower beam 90 mm - Upper bolster drive approx. 400 V / 1.8 kW - Bending beam drive approx. 400 V / 2.6 kW - Space requirement approx. W 4200 x H 1550 x D 2200 mm - Weight approx. 3800 kg
Offer 26093 Technical data: - Max. cutting length 3050 mm - Max. material thickness at 40 kg/mm², strength 2.5 mm - Cutting gap adjustment - Cutting angle 1°35 - Strokes 50 1/min - Stand projection 100 mm - Table height approx. 750 mm - Front angle stop 850 mm - 2 pieces support arms 500 mm - man. Backgauge can be operated from the front 5 - 750 mm - Sheet metal holding pneum. Supports - E – Footswitch - Drive 400 V / 5.5 kW - Space requirement approx. W 3800 x H 1500 x D 1400 mm - Weight approx. 2900 kg
Working lenght 2540 mm Material thickness max (400 N/mm²) 2.5 mm Upper beam upstroke max 280 mm Gauging system (rectangular) 6-1550 mm Gauging system (T-shape) 6-3050 mm
Key data: 3200 mm, 2 mm
used RAS 62.30 folding machine TurboBendPlus, a proven and reliable machine for professional sheet metal processing on roofs, walls and façade. The machine is ideal for tinsmiths, roofers, plumbers, locksmiths and metalworkers who rely on precise work results, robust technology and economic work. The RAS 62.30 impresses with its robust design and the high quality of the manufacturer RAS. It is ideally suited for everyday use Use in the trade and in the workshop. Used machines of this class offer an economically attractive opportunity to combine high-performance technology at a good price. The machine is equipped with a motorized depth stop, that facilitates precise and comfortable work. In addition, it has a segmented upper beam with a height of 110 mm, which makes the machine particularly can be used flexibly for different bending and bending work. This used RAS 62.30 is th ...
Key data: 3100 mm, 3 mm
- CNC control and electric 3x 400V, 50/60 Hz - CNC backgauge 5 – 750 mm - Machine frame with knife bar - Hold-down device with plastic coating - Sheet metal hold-up system - Cutting sorting system to the front and rear - Foot lever for adjusting the cutting material diverter - Built-in special knives (suitable for stainless steel) - Cutting gap quick adjustment - Cut line lighting with LED - Standard table trays - Front clippings collector - Safety device - (Protective fence right and left, light barrier) Working length: 3100 mm Sheet thickness steel: 3.00 mm Color: white / grey / yellow Dimensions: 3920 x 2370 mm with hold-down device Throat: 5-750 mm Speed: 26 strokes/min with angle stop Cutting angle of/up to :1000 mm Cutting angle: 1.1 degrees Min. back gauge: 5 mm Max. back gauge: 750 mm
Key data: 1020 mm, 2 mm
with bending rail 10 and 19 mm, additional segment insert for the upper beam (segment height 60 mm) and Material thickness adjustment, Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length: 1020 mm Sheet thickness steel: 2.0 mm Colour: green Machine weight: 350 kg Opening width: 150 mm Bending angle (max.): 130 degrees Machine number 16/9
Large working width: 3060 mm for sheet metal (at 40 kg strength) up to: 4 mm Kl. Bending radius: sheet thickness x 1.25 Kl. Inboard height: sheet thickness x 6 Opening width of the upper beam: 220 mm Adjustability of the lower/bending beam: 90 mm Max. bending angle: 180° Lifting speed down/up: 40/60 mm/s Hydraulic drive: 380 V, 7.5 kW Weight: 4.3 t Space requirement: 4150 x 1800 x 2500 mm
Max. bending length: 3200 mm Max. sheet thickness: 4 mm steel Motorized backgauge with hinged cams up to 2500 mm with stop extension (disassembled) Motorized bending beam adjustment Multibend 9001 controller Segmented upper beam tool with automatic tool clamping (height 100 mm) Operating instructions Weight: 5800 kg
Specifications: - Machine for the production of longitudinal folds on the edges - square or rectangular longer channels and - Number of roller shafts with folding rollers 15 pcs - Material thicknesses from 0.5 - 0.63 mm - Duct dimensions from 80 x 80 mm - up to 100 x 100 mm - from duct dimensions 100 x 100 mm - Material thicknesses 0.5 to 1.0 mm - Throughput speed 15 m/min - Pneumatic connection - Drive 400 V / 3 kW -with: - E. - Footswitch - Duct baffles - Separate lubrication device - Space requirement approx. W 5400 x H 1200 x D 800 mm - Weight approx. 950 kg
Key data: 3190 mm, 6 mm
Note: Machine is currently still being revised, the illustrations were made before the Revision. Sheet width: 3190 mm Sheet thickness steel: 6.3 mm Colour: grey Total power requirement: 18.5 kW Machine weight: 6800 kg Dimensions: 3830 x 3820 mm with cutting gap adjustment Stroke rates per minute: 30 - 50 strokes/min Angle stop: 1500 mm Throat: 5 - 1000 (1500) mm
Key data: 2500 mm, 2 mm
with foot switch, with simple control up to 6 bending angles, potentiometer preset, manual bending beam lowering, Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Sheet width: 2500 mm Sheet thickness steel: 2.5 mm without backgauge Colour: green Total power requirement: 16 A Space requirement: approx. 3400 x 1000 x 1600 mm Machine weight: 2000 kg without roller scissors Bending angle: 145 degrees Machine Number: 50/3
Gr. working width: 1250 mm for sheet metal up to: 1.75 mm Opening width upper beam: 70 mm Adjustability bending brace: 50 mm Space requirement: 1880 x 740 x 1140 mm
Specifications: Working length: 4060 mm Bending capacity: 3.0 mm Control with bending simulation: MULTIBEND 901 grafik 2D Automatic adjustment of the bending angle depending on material thickness Bending angle adjustment: 0 – 180° Backgauge motorized adjustable: 10 -1500 mm Max. opening bending beam: 300 mm Bending and lower beam adjustment range : 80 mm Motor power: 7.5 kW Dimensions (length x width x height): approx. 5500 x 4050 x 2600 mm Weight: approx. 6.8 tons
Offer 23317 Specifications: - Max. working width 2040 mm - max. material thickness at 40 kp / mm², strength 3.5 mm - Bending angle adjustment electronically pre-selectable 0 - 135 ° - Smallest bending radius 1.25 x sheet thickness - Minimum inboard height 6 x sheet thickness - Automatic sequential control for a complete workflow - Operation via hand or foot switch - Maximum opening width / stroke of the upper beam 200 mm - Height adjustability - bending beam 80 mm - the lower beam 80 mm - Upper beam drive 400 V / 1.1 kW - Bending beam drive 400 V / 1.5 kW - Manual backgauge can be operated from the front - Space requirement approx. W 3300 x H 1350 x D 1500 mm - Weight approx. 2600 kg
Folding machine RAS 22.11 - see pictures, Stand fold / double-standing fold
sheet width: 2540 mm plate thickness: 2,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 1,60 t dimensions of the machine ca.: m Manual backgauge up to 550 mm Side gauge and table extensions Sharpened blades The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2540 mm plate thickness: 2 mm thickness at Niro-steel: 1,25 mm no. of strokes: 63 Hub/min cutting angle: 1,13 ° table height: 750 mm table width: 320 mm back stop - adjustable: 5,0-550 mm total power requirement: 3 kW weight of the machine ca.: 1300 kg Equipment: - manual backgauge, with analog display Adjustable from the front stepless adjustment over the entire travel range - 1x long side stop - 3x support arms - Free-moving foot switch - Sheet holding device for thin sheet blanks The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2540 mm plate thickness: 2 mm thickness at Niro-steel: 1,25 mm no. of strokes: 63 Hub/min cutting angle: 1,13 ° table height: 750 mm table width: 320 mm back stop - adjustable: 5,0-550 mm total power requirement: 3 kW weight of the machine ca.: 1600 kg Equipment: - manual backgauge, with analog display Adjustable from the front stepless adjustment over the entire travel range - 1x long side stop - 3x support arms - Free-moving foot switch - Sheet holding device for thin sheet blanks The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2540 mm plate thickness: 2.00 mm thickness at Niro-steel: 1.25 mm no. of strokes: max. 63 Hub/min cutting angle: 1.13 Grad table height: 750 mm table width: 320 mm distance between columns: 2620 mm back stop - adjustable: 5.0 - 550 mm Control: konv. engine output: 3.0 kW weight of the machine ca.: 1600 kg range L-W-H: 3100 x 1980 x 1400 mm Equipment: - robust / motorized swing cut guillotine shears - break-proof, torsion-free steel welded construction - compact and clear machine design - manual back stop, with analogue display adjustable from the front stepless adjustment over the entire travel range - recessed grips in the support table - 1x hold-down bar - 1x side stop - 3x support arms - 1x freely movable foot switch - operating instructions (PDF) Special accessories included: - sheet metal holding device for thin sheet metal cuts The data for this ad was created wit ...
sheet width: 3200 mm plate thickness: 3.0 mm ST thickness at Niro-steel: 2.0 mm Opening width / upper beam: 300 mm speed: OW 40.0 mm/sec Bending beam adjustment: 80.0 mm speed: BW 90.0 Grad/sec work height max.: 900 mm control: MULTIBEND 5000 back stop - adjustable: 10 - 1550 mm accuracy +/-: 0.1 mm air pressure: 5.0 bar Number of working hours: ca. 1.000 h total power requirement: 2x 4.0 kW voltage: 400 V weight: 4400 kg range L-W-H: 4295 x 2225 x 1775 mm New price approx. 85.000 euros Machine with only approx. 1.000 operating hours () good condition () Special price on request - in checked condition - machine video - https://www.youtube.com/watch?v=VP6emx4HTYM ! Maximum flexibility when bending cassettes, boxes and profiles ! High flexibility in bending part design ! High productivity and throughput ! Easy to use Equipment: - motorized universal swivel bending machine RAS 73.30 hi ...
sheet width: 1280 mm plate thickness: 3.5 mm bending angle max.: 180 ° stroke of upper beam: 200 mm Swing beam adjustment: 30.0 mm Bending time for 90°: 5.5 sek Control: konv. voltage: 380 V total power requirement: 2.0 kW weight: 1180 kg range L-W-H: 1930 x 1750 x 1175 mm Features: - Simple electric motor-driven swivel bending machine - Manual angle adjustment via electric potentiometer - 1x bending tool set - Manual lower jaw adjustment .. 30.0 mm - Emergency stop button on the front - 1x freely movable dual foot switch - User manual (PDF) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
guillotine shears, sheet metal shears, metal sheet shears, crank guillotine shears -mechanical guillotine shears -Cutting width: 2040 mm -max. cutting thickness: 2.0 mm -Equipment: back stop, side stop, 3 supports -Drive: 5.5 kW -Installation dimensions: 2650/1900/H1070 mm -Transport dimensions: 2650/730/H1070 mm -Weight: 1378 kg
Offered is a RAS guillotine shear. Cutting length: 4040mm, max. steel sheet thickness: 5mm, backgauge range: approx. 5mm-1000mm, cutting angle: approx. 1.0°, stroke rate: approx. 28-46strokes/min, control system: RAS System 2005, weight: approx. 9200kg. Inspection by appointment possible.
A RAS beading machine is available. Working speed range: 0m-28m/min, max. sheet thickness: 1.75mm, back gauge: 330mm, weight: approx. 100kg. An on-site inspection is possible.
