4 RAS hydraulic shear used machines

Key data: 3190 mm, 6 mm

Note: Machine is currently still being revised, the illustrations were made before the Revision. Sheet width: 3190 mm Sheet thickness steel: 6.3 mm Colour: grey Total power requirement: 18.5 kW Machine weight: 6800 kg Dimensions: 3830 x 3820 mm with cutting gap adjustment Stroke rates per minute: 30 - 50 strokes/min Angle stop: 1500 mm Throat: 5 - 1000 (1500) mm

sheet width: 2540 mm plate thickness: 2,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 1,60 t dimensions of the machine ca.: m Manual back gauge up to 550 mm Side gauge and table extensions Sharpened blades The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2540 mm plate thickness: 2,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 1,60 t dimensions of the machine ca.: m Manual backgauge up to 550 mm Side gauge and table extensions Sharpened blades The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Offer 26238 Technical data: - Max. working width 3190 mm - Max. material thickness at 40 kg/mm², strength 6.3 mm - Cutting angle 1.2 ° - CNC - Cutting gap adjustment - Strokes 30 to 64 1/min - Stand projection 100 mm - Table height approx. 800 mm - Number of hold-downs 16 pcs - Back gauge 5 - 1000 mm - 3 pieces front support arms 1500 mm - E – Footswitch - Rear tilting roller table - Drive 400 V / 18.5 kW - Space requirement approx. W 3900 x H 1800 x D 2100 mm - Weight approx. 6800 kg - with : - CNC control RAS system - Rear tilting roller table / sheet metal hold-up - Rollable material collection container - Electronic rear space protection / light barrier

Panel shears Sheet metal scissors used Manufacturer: RAS / REINHARDT Maschinenbau Type: 82.20 Cutting width max. 2040 mm Sheet thickness max. 2 mm 380 V Dimensions approx. 2500 x 1500 x 1100 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.

sheet width: 2000 mm plate thickness: 2,25 mm distance between columns: 2040 mm total power requirement: 7,5 kW weight of the machine ca.: 1,5 t dimensions of the machine ca.: 2,2x1,7x1,1 m SN-No. 380/6 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2500 mm plate thickness: 3 mm distance between columns: 2540 mm back stop - adjustable: 550 mm total power requirement: 5 kW weight of the machine ca.: 2,7 t dimensions of the machine ca.: 3,2 x 2,5x 1,9 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 3100 mm, 3 mm

- CNC control and electric 3x 400V, 50/60 Hz - CNC backgauge 5 – 750 mm - Machine frame with knife bar - Hold-down device with plastic coating - Sheet metal hold-up system - Cutting sorting system to the front and rear - Foot lever for adjusting the cutting material diverter - Built-in special knives (suitable for stainless steel) - Cutting gap quick adjustment - Cut line lighting with LED - Standard table trays - Front clippings collector - Safety device - (Protective fence right and left, light barrier) Working length: 3100 mm Sheet thickness steel: 3.00 mm Color: white / grey / yellow Dimensions: 3920 x 2370 mm with hold-down device Throat: 5-750 mm Speed: 26 strokes/min with angle stop Cutting angle of/up to :1000 mm Cutting angle: 1.1 degrees Min. back gauge: 5 mm Max. back gauge: 750 mm

Stop for press brake, bending machine, guillotine shears ..., clamping angle, clamping aid,.Support rail for press brake, bending machine, guillotine shears, stop rail, clamping rail -Manufacturer: RAS, support rails from guillotine shears type RAS 53.60 -Dimensions: 805/100/H80 mm / groove width 16 mm 3 pieces -Dimensions: 720/75/H85 mm with stop rail 1 piece -Delivery/Price: complete -Transport dimensions: 805/350/H80 mm -Weight 34.8 kg

Offer 26093 Technical data: - Max. cutting length 3050 mm - Max. material thickness at 40 kg/mm², strength 2.5 mm - Cutting gap adjustment - Cutting angle 1°35 - Strokes 50 1/min - Stand projection 100 mm - Table height approx. 750 mm - Front angle stop 850 mm - 2 pieces support arms 500 mm - man. Backgauge can be operated from the front 5 - 750 mm - Sheet metal holding pneum. Supports - E – Footswitch - Drive 400 V / 5.5 kW - Space requirement approx. W 3800 x H 1500 x D 1400 mm - Weight approx. 2900 kg

Large working width: 4000 mm for sheet metal with a strength of 40 kg up to: 3 mm Table width: 470 mm Back gauge adjustment: 1000 mm Fixed cutting angle: 1°30' Column projection: 200 mm Hydraulic drive: 380 V, 7.5 kW Space requirement: 4650 x 1830 x 1420 mm high Weight: 5.7 t

Max. cutting length: 2540 mm Max. sheet thickness: 2 mm steel Manual back gauge up to 550 mm side stop and table extensions Knife sharpened 1600 kg

Offered is a RAS guillotine shear. Cutting length: 4040mm, max. steel sheet thickness: 5mm, backgauge range: approx. 5mm-1000mm, cutting angle: approx. 1.0°, stroke rate: approx. 28-46strokes/min, control system: RAS System 2005, weight: approx. 9200kg. Inspection by appointment possible.

guillotine shears, sheet metal shears, metal sheet shears, crank guillotine shears -mechanical guillotine shears -Cutting width: 2040 mm -max. cutting thickness: 2.0 mm -Equipment: back stop, side stop, 3 supports -Drive: 5.5 kW -Installation dimensions: 2650/1900/H1070 mm -Transport dimensions: 2650/730/H1070 mm -Weight: 1378 kg

sheet width: 2540 mm plate thickness: 2.00 mm thickness at Niro-steel: 1.25 mm no. of strokes: max. 63 Hub/min cutting angle: 1.13 Grad table height: 750 mm table width: 320 mm distance between columns: 2620 mm back stop - adjustable: 5.0 - 550 mm Control: konv. engine output: 3.0 kW weight of the machine ca.: 1600 kg range L-W-H: 3100 x 1980 x 1400 mm Equipment: - robust / motorized swing cut guillotine shears - break-proof, torsion-free steel welded construction - compact and clear machine design - manual back stop, with analogue display * adjustable from the front * stepless adjustment over the entire travel range - recessed grips in the support table - 1x hold-down bar - 1x side stop - 3x support arms - 1x freely movable foot switch - operating instructions (PDF) ** Special accessories included: - sheet metal holding device for thin sheet metal cuts The data for this ad was created ...

sheet width: 2540 mm plate thickness: 2 mm thickness at Niro-steel: 1,25 mm no. of strokes: 63 Hub/min cutting angle: 1,13 ° table height: 750 mm table width: 320 mm back stop - adjustable: 5,0-550 mm total power requirement: 3 kW weight of the machine ca.: 1300 kg Equipment: - manual backgauge, with analog display * Adjustable from the front * stepless adjustment over the entire travel range - 1x long side stop - 3x support arms - Free-moving foot switch - Sheet holding device for thin sheet blanks The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2540 mm plate thickness: 2 mm thickness at Niro-steel: 1,25 mm no. of strokes: 63 Hub/min cutting angle: 1,13 ° table height: 750 mm table width: 320 mm back stop - adjustable: 5,0-550 mm total power requirement: 3 kW weight of the machine ca.: 1600 kg Equipment: - manual backgauge, with analog display * Adjustable from the front * stepless adjustment over the entire travel range - 1x long side stop - 3x support arms - Free-moving foot switch - Sheet holding device for thin sheet blanks The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 40 t stroke: 250 mm total power requirement: 6 kW weight of the machine ca.: 3 t distance between columns: 600/350mm mm table surface area: 860x620 mm ram surface: 860x620 mm table height: 900 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Double Column - Hydraulic Press RASTER ZEULENRODA (WALTER) Type WUP S 60Masch. No. 136 / 7 (156-165) Year of manufacture 1999Basic machine from 1987, in 1999 Overhauled with new controlPressure capacity 60 ton. Stand width 1090 mmStand passage laterally 265 mm (one-sided) Plunger area 650 x 300 mmAdditional plate on ram 990 x 550 x 60 mmTable area 990 x 550 mmPlunger stroke max. 320 mmInstallation height 330 or 390 mmTable height above floor 980 mmHydraulics Operating pressure 320 barRapid traverse downward 75

Double Column - Hydraulic Press RASTER ZEULENRODA (WALTER) Type WUP S 60Masch. No. 136 / 7 (156-165) Year of manufacture 1999Basic machine from 1987, in 1999 Overhauled with new controlPressure capacity 60 ton. Stand width 1090 mmStand passage laterally 265 mm (one-sided) Plunger area 650 x 300 mmAdditional plate on ram 990 x 550 x 60 mmTable area 990 x 550 mmPlunger stroke max. 320 mmInstallation height 330 or 390 mmTable height above floor 980 mmHydraulics Operating pressure 320 barRapid traverse downward 75

Double Column - Hydraulic Press RASTER ZEULENRODA (WALTER) Type WUP S 60Masch. No. 136 / 7 (156-165) Year of manufacture 1999Basic machine from 1987, in 1999 Overhauled with new controlPressure capacity 60 ton. Stand width 1090 mmStand passage laterally 265 mm (one-sided) Plunger area 650 x 300 mmAdditional plate on ram 990 x 550 x 60 mmTable area 990 x 550 mmPlunger stroke max. 320 mmInstallation height 330 or 390 mmTable height above floor 980 mmHydraulics Operating pressure 320 barRapid traverse downward 75

Folding machine RAS 22.11 - see pictures, Stand fold / double-standing fold

Electric tool changer RASTER Premat EWD20

Many thanks for your interest on our second hand machines, please find follow our offer: manufacturer: Rasch Type: RR foiling machines for chocolate eggs with infeed System Year of manufacturing: 1987 pieces: 2 pieces output capacity: up to 150 pieces/min. Format on machine: Double twist Ei/Egg 43x27mm / Kugel/Bowl 30 mm. We offer this machine in 'as is' condition, without warranty excluded Vat, ex Work Germany, unpacked

RASKIN RT 64-2 punching machine manufactured in Switzerland in 1981, is designed for precise punching of holes in workpieces made of e.g. stainless steel, with a force of 30 tonnes. Technical parameters of the RASKIN RT 64-2 punching machine - maximum press force: 30 t - CNC control - number of strokes: 400/min - power supply of machine RT 64: 3x 380 V; 50 Hz