wood chip used for sale

Max Diameter 485mm Min length 1500mm, Max length 5500mm Drive power from the rotor disc 315kw Feeding step separator, feed belt, metal detector Removal Bruks 2x screws 1x 600x6.500mm and 1x 800x9.500mm Wood chip length 25mm Cabinets Year of construction/commissioning 2004 Working hours approx. 12500 hours Capacity 80-100 Qm3/h

Max Diameter 485mm Min length 1500mm, Max length 5500mm Drive power from the rotor disc 315kw Feeding step separator, feed belt, metal detector Removal Bruks 2x screws 1x 600x6.500mm and 1x 800x9.500mm Wood chip length 25mm Cabinets Year of construction/commissioning 2004 Working hours approx. 12500 hours Capacity 80-100 Qm3/h

– German production –DTR TECHNICAL PARAMETERS: width 400 mm height 120 mm rotor diameter 430 mm rotor length 430 mm engine power 37 kW motor power 2 x 2.2 kW number of knives 2 pieces sieve 60 x 60 mm two lower toothed shafts upper toothed shaft tray length 4900 mm wood chip chute with sieve transport dimensions (L/W/H) 850 / 245 / 220 cm weight ~ 2500 kg

Stack dimensions (LxWxH) - 16m x 1,4 m x 1,6 m automatic drying by means of computer Heating power - 90 kW Top Condition

Cutting Height - 250 cm, with small changes even up to 300 mm. Width - 450 mm. Feed continuously, up to 40 m / min. 2 moving sockets for 3 blades each and one middle socket is possible. Engines - 2 pc. each 45 kW Complete with round wood feeder. Wood rotating device and centering. Automatic remote control.

Motor logs gripper with electro-hydraulic drive. Diameter: 1,000 mm Weight: 1,260 kg Drive parts: 1) Electric motor 5.5, kW - 100% ED, protection class IP 54, rotary 1,450 rpm, operating voltage 380 V, 50 Hz 2) Constant pump - axial piston - inclined axis design, type A2FM. Flow capacity 23.2 l/min 3) Hydraulic cylinder (2 pcs.) Type 80/55, MAKE MRS double-acting, piston rods hard chrome-plated 4) Tax block NG 10, make Of Herion Turning ranges, change of direction of rotation changing from right to left and left to right, for all drive parts of Pos. 1) - 4) Fittings: made at Ermeto Electrical control: Installation according to electric circuit diagram No. 26.0.144.4 In very good condition!

Recycling plant with all necessary permits for the processing of wood, metal, plastic, compost, etc. is provided the supply of biomass to operate a remote heating system with 2-3 MW of power. There are corresponding contracts with energy buyers. Plot 7200 m2, fixed and is partially built over 2000 m2 Preparation year 2012-more information at Peter Ari Schär of MATEC Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland

gebr. Wooden tongs / tree pliers / pipe wrench

Wood Turning Lathe Precision device for professional users, with grey cast iron variable speed control high degree of spindle concentricity Spindle can be fixed all 15° LCD speedometer One hand operation of the tailstock and tool rest with quick-release mechanism Voltage: 230V / 50 Hz Engine power: 735W (S1 100%) Tip height: 160 mm Top width: 510 mm Speed ranges: 250-750 m-1, 550-1650 min-1, 1300-3850 min-1 Spindle stock rotation: 180 degrees Headstock thread: M33 DIN800 Morsekonusaufnahme: MK2 / MT2 Quill stroke: 63 mm Weight: 52 kg Dimensions: 1035 x 305 x 449 mm G & HM-D510F

Slow runner with sliding floor 800 mm wide rotor 22 kw engine

Slow runner with sliding floor Rotor width 800 mm 18.5 kw motor

The ECOSTAR 8 slices hacker with diesel drive 35 HP, 3 cyl., with an increased swivel discharge for horticulture, wine fruit, forestry, agriculture, etc. at a cheap price. With 2 blades, disk diameter 605 mm, disc speed 1200 rpm, JD diesel engine 3100, 3 cyl, 35 HP, water-cooled, feed height 200 mm, max wood diameter 200 mm, Einzugbreit 225 mm, hopper opening 600/600 mm, output per hour 5-8 cubic metres. The machine is ready for use within 1 minute. The chips can easily be abandoned on the bridge of the towing vehicle. The tedious tying of the branches fall away. Take the chips only 1 time in the hands. Watch the video movie in matnews91 on YouTube: ECOSTAR diesel JD3100 8. Price does not include trailer euro 9' 390.00 Expressly subject to technical changes, prior sale and error! Shipping costs CH / DE trucked approximately euro 280.00 MATEC systems + technology GmbH K ...

Wood chopper f. tractor PTO wood chipper ECOSTAR 8 as a kit for the self-Assembly (image mounted with other rotating device) - feeder height width 20/20 cm - upper feed roller with belt drive - disk hacker with 2 knives and 1 counter knife - rated about 5 cubic metres chip length nominal 15 mm - CE compliant - PTO - rotating ejector - delivered in metal crates -Warranty: 2 years on all non - consumable - options for an additional fee: - machine Assembly by supplier - pulverizing integrated to avoid excess - special execution for the manufacture of Pelletschnitzeln with 6 mm length - professional Rotary chute which together does not rust and freezes at Sub-zero temperatures, with lever - built diesel drive 35 HP - electric motor 15 kW model changes built up which are not exactly the figurative representation are reserved! Spare parts/service MATEC CH-4952 Eriswil/DE-79618 Rheinfe ...

Wood Turning Lathe big turning diameter over bed allows the turning of workpieces with large diameter - ideal for turning E.g. plate user friendly adjustable speed Digital speed display comfortable working with hand pad and quick adjustment Spindle/tailstock bore 10 mm Top width: 457 mm Tip height over machine bed: 153 mm 3-stage variable spindle speed: 650-1450 min-1, 1250-2800 min-1, 1600-3800 min-1 Headstock, thread: M33 DIN800 Motor power S1 (100%) / S6: 550W / 770W Mains voltage: 230V Net weight: 33kg G & HM-D460FXL

Important and outstanding design features of the RaptorX-SL with steel substructure / RaptorX-SL2200/S20 The application variety of a RaptorX-SL CNC Fraes machine is variable due to the adjustable working area (read-through shoe under bridge: 150mm, 300mm or 400mm ) and the travel height of 300mm in the Z-axis (at no extra charge) extremely large. special groesmes up to 17,500 mm (at one scale ) x 3000 mm x 600 mm are possible ! If you are interested, please ask ! So you are able to process plate materials with the greatest stability of the Z-axis just as precisely as 200mm high 3D-plates. Use the system as a plasma cutting system or waterjet cutting system, corresponding extensions are available. In the middle range of the machine (between the footpipes ) you can even process parts up to a height of 850mm (beam shroughl, etc. ) or 3D body up to about 400mm height (at 400mm ...

Specifications / Technical data S-1000/T Portalfraesmaschine / Engraving machine With the T-variant of the High-Z CNC-Fraese you acquire old-fashioned technology with the certain i-tuepfelchen in TUeV-certified quality (Emc). The High-Z/T Fraese is designed for even more accuracy (repeatability about 0.01mm ) and especially for higher travel speeds. Through the ball-circuit spindles used, the High-Z/T achieves fantastic accuracy and an almost unmeasurable reverse play of about 0.01mm. At the same time, high travel speeds of up to approx. 108mm / second ( 6500 mm / minute ) can be achieved. This is how engraving and fraes speeds of up to approx. 4500mm/min can be realized and urgent journeys up to approx. 7000mm/min. Here you can see a video about empty runs with the new high-Z/T 3D CNC machine. This makes this machine series in the industrial sector just as applicable for work ...

PIN cutting machine Clamping width of 240 mm beam height of 320 mm spigot strengths of Max 130 mm PIN length of 350 mm motor power 2,2 kW 380 Volt motor weight approx. 120 kg

Specifications / Technical Data S-1000/T CNC-Router / CNC-Engraver With the purchase of the T-variation of High-Z CNC-router you get a proven technology with a certain icing of the cake in TÜV-certified quality. High-Z/T was conceived for once more precision (repetition precision approx. 0,02mm) and especially for higher traverse speed. Because of the used ball screws the High-Z/T CNC-engraver achieves a fantastic precision and an almost unmeasurable back lash of approx. 0,01mm. At the same time there are high traverse speeds up to approx. 108mm / sec. ( 6.500 mm/min ) possible. With this cnc-machine you're able to carry out an engrave and mill speeds of approx. 4500 mm/min. and express travels up to 6500mm/min. Here's a video on a unloaded drive with the new High-Z / T. This cnc-router series is usable in the industrial field as well as for works like engraving, milling, dr ...

Specifications / Technical Data S-720/T CNC-Engraving-Machine / Milling machine / CNC-Router With the purchase of the T-variation of High-Z CNC-router you get a proven technology with a certain icing of the cake in TÜV-certified quality. High-Z/T 3D-cnc-engraver was conceived for once more precision (repetition precision approx. 0,02mm) and especially for higher traverse speed. Because of the used ball screws the High-Z/T cnc milling machines achieves a fantastic precision and an almost unmeasurable back lash of approx. 0,01mm. At the same time there are high traverse speeds up to approx. 108mm / sec. ( 6.500 mm/min ) possible. With this cnc-machines you're able to carry out an engrave and mill speeds of approx. 4500 mm/min. and express travels up to 6500mm/min. Here's a video on a unloaded drive with the new High-Z / T. This cnc-machine series is usable in the industrial ...

Equipment / Product data of the CNC-Fraesen Type High-Z/TRex series / Type 1215 Drive: 3 busiest brand stepper motors with 4.5 amperes. Pushing through long and up to 120mm high materials possible, as no belt drive is in the way at the end of the X axis! linear guides on all axes of HIWIN / THK ! Multiple ball-bearing ball thread spindles on all axes, brand edging! speed speed max. 12,000 mm/min Working speed max. approx. 8,000 mm/min Technical platform X/Y: 0.005mm (1/10 step); Z: 0.0025mm reverse play maximum approx. +/- 10 microns (0.010 mm) Point repeatability: approx. 0.01 mm clamping area 1860 x 1340 mm travel distances: X=1500mm; Y=1200mm; Z= 130 mm contact contactno-point sensors / reference switches / limit switches on all axes Double-secured emergency trigger energy chains for clean cable Total mass with motors : LxWxH approx. 2180 x 1800 x 1420 mm Fra- Sc ...

3D CNC Router T-Rex 1215 / Technical Data : Equipment / product data CNC-milling machine type High-Z/TRex series: Drive: 3 brushless brand stepping engines with 4,5 ampere. Possibility of sliding through long and up to 120mm high materials, no belt drive at the ende of the X axis! Linear guide on all exis by HIWIN / THK ! Multiple ball-bearing ball-screw spindle on all axes, proprietary brand! Rapid traverse max. ca. 12.000 mm/min Operating speed max. ca. 8.000 mm/min Technical definition X/Y : 0,005mm (1/10 Schritt); Z: 0,0025mm Backlash maximal ca. +/- 10µm (0,010 mm) Repeat accuracy: ca. 0,01 mm Clampin surface of grooven panel / T-slot table 1860 x 1340 mm Travels: X=1500mm; Y=1200mm; Z= 130 mm Non-contact reed sensors / reference switches / limit switches on all axes Double secured emergency-stop button Energy chains for a clean cable routing Total dimensions wi ...

Slow runner with sliding floor 800 mm rotor width 11 kw motor good condition

Slow runner with sliding floor 800 mm rotor width 11 kw motor

Optical measuring geraet from Bundeswehr bestaenden, probably unused Manufacturer Leitz Adjustment equipment Pipe weapon for target line testing Kal 20 to 260mm with adjustment telescope Target line tester new condition Completely! Rest according to photos Special price

Slab formwork, wall formwork, wooden beams, props, formwork accessories used immediately operational. We are happy to answer questions phone 06190-93449-0 The material can be visited by appointment, we buy also. Note also our other ads! We can offer you several thousand square metres of used formwork, scaffolding and tools - ask us!

Type Overture ES Voltage 230 V (50 Hz) Made in USA Transport dimensions 600x400x500 mm Weight 15 kg

Description ID U109.3 Status Active Price 100 € + VAT Year of manufacture 1985 Location Oradea (RO) Pneumatic press for wood labeling. ExWorks. Price is negotiable. Contact Tel.: +40-359/175.575 Fax: +40-259/426.248 Mobil: +40-743/177.040 ; +40-740/221.698 Technical inspection can be organized at least 24 hrs before the due date We speak English. Wir sprechen Deutsch. (+40-740/221.698 ) Hablamos Español. Beszélünk magyarul. (+40-743/177.040 ) Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervam dreptul la greseli, modificari si vanzare prealabila.

Laser sensor Error detection automatically Shape recognition Laser printer (DIN A4) Number 2 Monochrome cameras PHOTONFOCUS 160 MB Number 2 Barriers + Accessories

Hydraulic gripper for wooden beams with modular suction cups Load capacity kg: 700 Number of suction cups: 16 Dimensions of suction plate mm: 80 x 750 Procedure mm: 8000

Turning machine Tip height 150 mm Tip width 650 mm 2 speeds Flat disc diameter 240 mm Electricity connection luminous flux Dimensions 1230 mm x 620 mm x H 1620 mm

Funnel hacker - Shredder DHB DH 600 Rotor width: 600 mm Rotor diameter: 220 mm Number of knives: 28, concave sanded, quadruple rotatable Engine power: 18.5 kW Electrics: 400V, 50 Hz Control: Control cabinet, blower cooled, Siemens PLC Opening: 600 x 785 mm Funnel volume: approx. 0.60 m3 Screen: 20/25 mm mounted (screen size 10-80 mm possible) Hydraulics: 40 litre tank, external gear pump Dimensions: 1750 x 1280 x 1650 mm Weight: 1820 kg Throughput: 1-3 m3/h, depending on material and screen size Suction nozzle: 160 mm Suction capacity: min. 28 m/s extended funnel

TECHNICAL DATA: Capacity Kg/h: 1.800/2.500 Dimension mm: 8300 x 2900 x 2200 Opening width mm: 800 02 Milling Units Ø mm: 250 Total power installed kW: 103 Weight kg: 10.500

WEIMA shredder for carpentry-carpentry sawmill waste -old wood etc. Type:WL 4. Feeding opening: 600x1050.mm. ( Log Funer ) Rotor diameter:252.mm. Rotor width:600.mm. Drive power:18.5kW. Tools: ( Knife piece 28.) 40x40.mm. Koncav Vs9lrq Weight:1300.kg.

Exhibition machine Inlet width: 1,400 mm Inlet height: 550 mm Rotor diameter: 1,600 mm Chopping knife count: 4 pieces Counter-knife number: 1 pc. with cutting gap adjustment Feed unit: 2 x 5 rollers Drive: 250-500 kW Machine weight: approx. 30,000 kg

TECHNICAL DATA: Size of the table mm: 1200 x 700 Sanding belt width mm: 90

Towed chopper TP 760 P, wood chopper with feeder approx. 160x260 mm, combination with Reiser SCH 230 container tipper. Container loading capacity 3.5 m3, high emptying to approx. 224 cm, additional loading flap in the rear. Tyres 10.0x75-15", parking brake, Total weight 2,800 kg. Machine in non-operational condition. More bush hackers and wood chippers in stock!

Max sanding&Turning lenght 1300 mm Max diameter 160 mm Spindle power 3 HP

Various steel sheets and wooden wagons with wheels Length 1350 - 1700 mm x width 400 - 860 mm x height 1040 - 1720 mm Price: EUR/piece 28,- net + VAT approx. 10 transport aids 1110 x 600 mm Price: EUR/piece 15,- net + VAT

Usable for the: Milling and engraving labeling, marking Drilling, cutting Dosing and much more. (Applications require optional accessories) inclusive: Design software ConstruCAM 3D Control software KinetiC-NC incl. CAM software Estlcam Multi-zone vacuum table with recessed T-nuts sliding Control panel including step control manual central lubrication The offer here is a CNC milling machine with the above-mentioned accessories (without further ado possibly shown on the photos accessories). For operation, a milling motor is also required, which can optionally be purchased from us. echnische data: External dimensions LxWxH: 1650x1440x1950 mm Weight: approx. 650 kg Clamping surface XxY: 930x630 mm Travel XxYxZ: 900x600x200 mm (optional 300/400 mm in Z-axis) Width linear guides X,Y,Z: 20 mm Repeatability: 0.01 mm Reverse play: appr ...

CATALOG NUMBER 6114 TECHNICAL DATA - 800x1000mm loading hopper inlet - rotor working width 800mm - pump motor 0.75kW - 15kW main engine - number of knives 21 pcs - dimensions of the knives 30x30mm - 0.8x10mm sieve - pressure drawer - electric reverse - 2 × 1.1kW discharge augers - dimensions length / width / height 2460x1800x2250mm - weight 1660 kg - German production - reverse - pressure drawer - unpainted - very good condition - used chipper Net price: 69 900 PLN Net price: 16,069 euros depending on the price, 4.35 euros (Prices may vary for greater fluctuations)

Work facilitation through basic equipment The basic equipment includes, for example, an ergonomic control panel, which contains the stepper motor control and an industrial PC with touch function. Software (CAD/CAM, control software, operating system Win 10 Pro) are already pre-installed. Thus, the CNC milling machine can be operated conveniently and conveniently. A multi-zone vacuum table ensures a comfortable, fast clamping of workpieces and a strong hold during milling. Furthermore, the machine is equipped with a manual central lubrication, which makes it easier for you to grease and increases the service life of the CNC milling machine. Various applications The most diverse materials can be processed on our T-Rex, whether plastic, wood, metal or stone, nothing is impossible. Whether engraving, milling, cutting, drilling, dosing, gluing, etc., no wishes remain unfulfille ...

Hydraulic wood splitter, functional Details on request

Shredding Machine Hacker Shredder Manufacturer: WEIMA-Maschinenbau Type: WL.4. Drive:18.5Kw. Feed opening:600x1050.mm. Rotor width:600.mm. double knife row (28.pcs.) Sieve size: still selectable

Capacity (x): 0 Process Application: 0   Other Info: 0 Technical data Voltage 50 Hz 3x: 380 Volt Power: 1.83 A Overall dimensions machine: Length: 2000 mm Width: 1000 mm Height: 800 mm

Capacity (x): 0 Process Application: 0   Other Info: 0 Technical data Table length: 850 mm Table width: 500 mm Longitudinal travel (X-axis): 400 mm Voltage 50 Hz 3x: 220 Volt Machine´s weight about: 400 kg Overall dimensions machine: Length: 900 mm Width: 650 mm Height: 700 mm Various accessories: Digital readout number of axis:: 2 Projector: Screen diameter: 180 mm

Capacity (x): 0 Process Application: 0   Other Info: 0 Technical data transfer printing process machine Execution: Elektro-pneumatic Printing block dimensions: Length: 80 mm Width: 80 mm Dimension of the workpice: Diameter: 50 mm Imprint dimension: Length: 50 mm Width: 50 mm Production: 2400 pce/h Air consumption min.: 6 atm Air consumption about: 2.3 m3/h Voltage 50 Hz 3x: 220 Volt Machine´s weight about: 75 kg Overall dimensions machine: Length: 600 mm Width: 540 mm Height: 350 mm