129,263 used machines on RESALE, but how to find them? Machine Search
Technical characteristics: Rated power: 2000 kVA Primary voltage (HV): 20,000 V Secondary voltage (LV): 400 V Adjustment positions: 1: 21,000 V 2: 20,600 V 3: 20,000 V 4: 19,400 V 5: 19,000 V Frequency: 50 Hz Phases: 3Isolation level: HV: 125 kV / AC 10 LV: AC 10 Cooling: KNAN Service Plan: Ongoing Connections: Connection diagram: Dyn11yn11 Output voltage: 400 V – 50 Hz Multiple Connection (Low Voltage): 1W, 1V, 1U / 2W, 2V, 2U Short-circuit current: 5.83 kA Short-circuit impedance: 6.1% Cooling & dielectric: Dielectric Fluid Type: MIDEL 7131 No-load loss rate: 1873.1 W Load Drop Rate: 15.1 kW Location :p aris Condition: Very good condition – Tested and ready-to-use hardware Disassembly and transport possible on request
Inv. Num. : 5457 Type: UB 63/2000 Producer: HOL-MONTA Created: 2001 Parameters: Control system: Kavalír Maximum grinding length: 2000 mm Grinding diameter: 630 mm Tip stroke: 375 mm Total power requirement: 41 kW
; Gross weight [kg]: 5847; Engine: Perkins 4016TAG1A; Accessories: Control Panel, Including: Coolant heater and battery charger
Banding system ATS US 2000 AB Cornerline; good condition; serviced and tested by ATS customer service; bandwidth 30mm; frame size 360x160mm; Min. Product width 80mm, max.165mm; Max. Product length 270mm; Max. Produnkt height 110mm; Compressed air required. Ultra sonic banding machine ATS US 2000 AB Cornerline; good condition; cleaned and checked by the support of ATS Germany; band width 30mm; frame size 360x160mm; min. product width 80mm, max.165mm; max.product lenght 270mm; product hight 110mm; pressure air needed.
Very high-quality CNC – controlled precision sheet metal round bending machine with automatic bending sequence calculation – automatic CNC – controlled double-sided pre-bending – conical bending device, three hydraulically driven rollers (one hydraulic motor per roll), hydraulic linear sub-roll adjustment – hard chrome-plated piston rods – hardened and ground rollers - PILZ® laser protection - BECKHOFF® CNC – control with Ethernet technology and large touch screen - DANFOSS® precision hydraulics – central lubrication system Maximum bending length 2,000 mm Roll diameter 170 mm Smallest weft diameter = 1.1 x the roll diameter The rollers run in bronze plain bearings. Nominal pre-bending performance over the entire bending length at 5 x D = 5 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 7 mm sheet steel/ST40 Drive ...
Grinding machine Löwer double-sided Type: DSM 2000 Year of Make: 1996 CE Grinding width 190 mm Grinding thickness – material thickness 2 – 180 mm Sanding belt dimensions 200 x 1800 mm Wear-free ceramic sanding shoe (no graphite coating necessary) Motorized height adjustment 0.37 kW Workpiece length min. 300 mm Feed speed 6/11/16 m/min. Sanding belt drive 2 x 5.5 kW / 400 V Sanding belt speed 22 m/sec. 1 sanding shoe and cleaning brush from above 1 sanding shoe and cleaning brush from below Blow-off device in front of the outlet Suction nozzle diameters 2 x 150 mm and 2 x 120 mm Inlet height 850 mm Total connected load approx. 14 kW Incl. workpiece return consisting of inclined chute and return roller conveyor good, ready-to-use condition Machine dimensions: L 2070 mm x W 920 mm x H 1890 mm Weight approx. 1500 kg
: 15000 kg height: 790 - 1350 mm width: 2000 mm : ja : 120 x 2000 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter over bed: 460 mm turning diameter over slide rest: 274 mm turning length: 2000 mm spindle bore: 58 mm spindle turning speed range: 25 - 2000 U/min turning dia. in gap: 690 mm metric threading: 41 / 0,1 - 14 mm thread - inch: 60 / 2 - 112 inch. thread - module: 34 / 0,1 - 7 mm Whitworth-thread: 60 / 2 - 112 TPI adjustment of the upper slide: 140 mm dia. of quill: 60 mm quill stroke: 120 mm total power requirement: 5,5 kW weight of the machine ca.: 1,7 / 2,0 t dimensions of the machine ca.: 2,2 x 1,0 x 1,3 m A comprehensive range of quality centre lathes characterised by wide versatility,high accuracy and extremely rigid construction. The machines are well equipped with a multi-fix quick change tool post and 2-axis Newall digital readout fitted as standard and a variable speed option is available. Huvema lathes fully conform to CE regulations. Also available in: 1,5m 3 ja ...
Number of sanding units: 2 St. sanding width: 190 mm Sanding height max.: 2-180 mm LÖWER-Doppelseitige Schleifmaschine DSM 2000 Doppelseitige Einzelholzschleifmaschine zum Schleifen von Massivholz wie z.B. Fensterhölzern etc. Stabile Top-Aus- führung mit langen Gußtischen, Bürst- und Finisheinrichtung und Transportbandvorschub. Geeignet für hohe Dauerbelastung auch bei höheren Spanabnahmen. - versetzt angeordnete Schleif- und Finishaggregate oben und unten - direkt angetriebene gummierte Schleifrollen für schlupffreie Kraftübertragung - Kombischliff über Rolle und Schuh für hohe Spanabnahmen bei gleichzeitig ebener Eingriffszone - wartungs- und verschleißfreie CERMET-beschichtete Schleifschuhe mit sehr guter Wärmeleitfähigkeit und absoluter Maßhaltigkeit - Fremdkühlung der Schleifzonen für einen kühleren Schliff und höhere Schleifbandstandzeiten - zwangsgeführte pneu ...
table length: 2000 mm table width: 1000 mm table height: 850 - 900 mm weight of the machine ca.: 0,45 t Welding table / perforated table: Hole diameter: 28mm The table is made of 15mm thick, high-alloy steel S355 JR T = 15 The surface is untreated. Sidewalls 165mm height adjustable from approx. 880 - 980mm Ribbed underside for reinforcement. including floor storage Accessories optional Surface flatness 0.2 - 0.4mm on 1000mm. Very sturdy base, so the Table can be moved with a pallet truck. The accessories shown are optional! Pallet truck is not included in the scope of delivery The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 2000 mm Working width: 360 mm Wheel width: 360 mm roll diameter: 60 mm : 800 kg height adjustment: 650 - 950 mm weight of the machine ca.: 0,045 t dimensions: 2,07 x 0,48 x 0,21 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
width of the strips: 150 mm band length: 2000 mm band speed: 33 m/sec total power requirement: 4 kW weight of the machine ca.: 100 t dimensions of the machine ca.: 1,2 x 0,5 x 0,85 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
width of the strips: 75 mm band length: 2000 mm band speed: 37 m/sec total power requirement: 3 kW weight of the machine ca.: 0,105 t dimensions of the machine ca.: 1,2 x 0,5 x 1,0 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Counting and banding machine ATS US 2000 FSB-DBN-T; State as is; should be installed by ATS Customer Service; suitable for processing banknotes; Rontech MF-360 RAV counting feeder; 1x Banderolier ATS US 2000 AD bandwidth 40mm and frame 260x260mm; 1x Banderolier ATS US 2000 AD Bandwidth 30mmund Frame 260x120mm; Turning unit installed. Count and banding machine ATS US 2000 FSB-DBN-T; condition as is; should be installed by the support of ATS; used for banknotes; count feeder Rontech MF-360 RAV; 1x banding machine ATS US 2000 AD with band width 40mm and frame 260x260mm; 1x banding machine ATS US 2000 AD with band width 30mm and frame 260x120mm; turning station.
table diameter: 800 mm table load: 2 t swivelling range: --> 95 Grad max. torque: 1250 Nm table rotation speed: 2 U/min Working height from to: 550 - 1300 vertikal mm Working height from to: 650 - 1400 horiz. mm total power requirement: 2,53 kW weight of the machine ca.: 930 kg dimensions of the machine ca.: 1,85 x 1,66 m Electric 400 Volt: Hand control panel: Hydraulic-device: Hydraulic positioner for permanent turning right + left, tilting, Raise and lower. Machine dealer with own stock of 2500 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
0: , St. Width: 1080 mm Length: 2000 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 2000 /1000 t distance between columns: 2650 mm stroke: 500 mm column travel -side: 500 x 1000 mm diameter of piston: 710 mm number of pistons: 2 distance between table / ram: 1000 mm operating pressure: 130 / 230 bar dayligth: 800 mm table length: 2500 mm table width: 1600 mm table height: 250 mm draw back pressure: 500 kN number of T-slots: 8 turning speeds: 1500 U/min rapid speed: 120 - 140 mm/min closing speed: max. 120 - 140 mm/sec. hydraulical ram locking: return of plunger by small single cylinders: 100 - 110 mm/sec cutting sound absorber: 300 t die cushion capacity: 200 t die cushion stroke: 250 mm speed of die cushion: 100 mm/sec voltage: 380 V frequency: 50 Hz quantity of oil: 2000 l total power requirement: 93 kW weight of the machine ca.: 90 t dimensions of the machine ca.: 5000 x 2500 x 7200 mm transport measurements: ca. 6500 x 3750 x 2190 mm 1991 assembly of a di ...
For sale pallet changer / inverter /. Capacity - 2000 kg.
USED LÖDIGE FKM 2000D STAINLESS STEEL 2.000 LITRES BLENDER REF#: C5725 Lodige FKM2000D mixer with a total volume of 2000 liters manufactured in 316 stainless steel. Two inspection doors with a 55 kw geared motor completely reconditioned. General characteristics: Manufactured by LODIGE Model FKM 2000D Material Stainless steel 316 Year built 1973 Weight 3700 kg (2060 kg + 1640 kg motor and reducer) Technical characteristics: Capacity 2,000 L (800-1,400 L useful) Motor characteristics: Manufactured by SCHORCH Voltage 400/690 V Current 94/55 A Power 55 kW Frequency 50 Hz cos(fi) 0.89 Rotational speed 2960 rpm Reducer characteristics: Manufactured by ELENDER Model SZBW 250 Ratio 0.04 Rotational speed 120 rpm
We can offer a Krauss Maffei injection moulding machine, manufactured in 2017, short time working, like new one, serious buyer contact us. We have many brands, models,years machines, tell me what you need seriously!
hydraulic tipping tank or tipping bucket Price: 800,-p.pcs. + VAT reclaimable: R928 hydraulic tipping trailer, tipping wagon MAFI hydraulically tiltable by means of a manual hydraulic pump. Load capacity 2000 kg Overall height 2000mm Inner body dimension Br.1900mm Flat 900mm top 1450mm 2 pieces are to be handed in Because they have been stored for years, they are partly rusty or the paint is peeling off. Otherwise very good technical. Condition in my opinion see also photo of the cylinders easily convertible as a tipping container on a forklift (has been done before) unscrew the chassis weld on 2square tubes for fork mounting Unscrew the manual hydraulic pump with quick couplings and adapt it to forklift hydraulics It is best to visit and try it out for yourself. I had several at one of them the chassis was removed and the holder for forklifts was welded on, intended for wo ...
Both filling stations are in good condition, little in use.
Pausch recording workstation Compact CS 2000 with the following device components: Generator Editor Hfe 501 Tube RAD 21 0.6/1.2 Varian Vertical tripod BS 2000 • Before taking over, all devices or systems have been tested on site for their functionality. • The system is located in our warehouse in Freiberg / Germany. It is packed on pallets, professionally railed and with Stretch film wrapped and can be picked up immediately • You buy the system in "ACTUAL" condition from the warehouse Freiberg (EXW), Saxony, Germany, and advance payment. • The sale takes place as "used", EXW Freiberg, Saxony, Germany, to resellers or dealers despite full Functionality without guarantee. • The installation and configuration of the system or plant components must be completed by a specialist authorised by the manufacturer or technicians!
GEA type 200023512 Intercooler Ladeluftkühler MTU Einwandfreier Zustand perfect condition from an MTU4000 engine that has been running for 25,000 hours von einem MTU4000-Motor, der seit 25000h in Betrieb ist
Arburg 520C-2000-675 (154) without funnel General information Item number: 154 Availability: In stock Year of construction: 1998 Brand: Arburg Specifications Spray weight: 240 g Clamping force: 2,000 kN Screw diameter: 45 mm Spray pressure: 2500 bar Spar spacing: 520 x 520 mm Clamping plate size: 715 x 715 mm Tool installation height min.: 250 mm Control: Selogica Language: German Power: 44.9 kW Operating hours: 126766 h Weight: 6630 kg Dimensions: 5.6 x 1.7 m Euromap: Yes Air valve: Yes
used
Technical key data: • Type: Oil transformer (hermetically sealed) • Power: 2000 kVA • Primary voltage: 20 kV + 4x 2.5% see sign • Secondary voltage: 400 V • Frequency: 50 Hz • Condition: Used, technically tested • Delivery: ex warehouse in Lippstadt – nationwide Dimensions: L 220cm W 78cm H 195cm ✅ Your benefits: • Tested, ready to use immediately • Delivery & transport solutions available • Expert advice Monday to Saturday, 8 a.m. – 10 p.m. ⸻ For price, availability or other technical data, please send us your request. Contact: Mr. Schmidt – Technical Purchasing Mobile: 0172 / 72 653 24 Fax: 02941 / 96 77 832 We look forward to your inquiry! Best regards,
pressure: 200 t distance between columns: 1600 mm max. ram stroke: 600 mm dayligth: 900 mm table width: 1600 mm table depth: 1300 mm table height: 1060 mm ram surface: 1600 x 1300 mm T-slots: Din 650 / 22H12 rapid traverse: 400 mm/s return speed: 325 mm/s pressing speed: 42 mm/s bei 40% mm/sec pressing speed: 20 mm/s bei 100% mm/sec die-cushion pressure: 800 kN die cushion stroke: 150 mm speed of die cushion: auf 68/ ab 225 mm/s The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
working width: 2000 mm for sheets up to: 3 mm Clear stand width: 2050 mm Stand discharge: 250 mm Support table size: 220 x 2200 mm electr. Drive: 380 V, approx. 5 kW Weight: 2.7 t
An indestructible machine for the toughest conditions. The machine is suitable for processing raw wood. The machine has no inclination. The saw blade is located directly on the motor. Technical parameters: Maximum saw blade diameter: ø 500/mm Power of the main motor: 5.5 kW Main speed of the saw blade: 2850 rpm Maximum cutting height: 85 mm (with 350 mm saw blade) Inclination of the saw unit: NO Dimensions of the iron table: 1050 × 600 mm Aluminium formatting table: 2000 × 360 mm / OPTION 3200 x 360 mm Formatting table for hardened rods (Altendorf principle) Cutting length: 2000 mm Weight of the machine: 450 kg Given the prices of new Chinese machines that cannot withstand the harsh conditions, this machine is the solution. Made in Slovakia in Europe
I sell a drill with cutting units COMEC FM0V8 2000, built in 1997. Working width max. 2000mm Configuration: 0 motors from below 1+1 motors from sides / angular adjustable 2 motors from behind / head angular adjustable 3 motors from above / head angular adjustable 4 pieces of material prints from above 2 cut saws from above / head angular adjustable Atypical 5-spindle drill heads Including 3 x 15mm / 2 x 25mm. Dubel heads in the price. Very good addition. Available the same.
Machine type MIG/MAG inverter welding system Böhler brand Type Uranos 2000 SMC Connection voltage 1 x 230 Volt Setting range 5 – 200 amps Duty cycle 35 % ED at 200 amps 60% ED at 160 amps 100% ED at 130 amps Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version portable mounting system Wire feed gearbox 2-roller gearbox Fuse 16 amps Dimensions L x W x H 500 x 210 x 400 mm Special accessories TIG DC welding without HF E-welding, MIG soldering Weight 13 kg Age 6 months Condition workshop tested, as new, incl. UVV test report Scope of delivery welding system with the following accessories: 1 piece welding torch, 3 mtr. long 1 piece ground cable 1 piece pressure reducer argon with 2 pressure gauges 1 roll of welding wire D-200 coil, 5 kg 1 can of non-stick spray 1 piece ...
cleaned & checked 220 Volt / 1500 Watt / 50-60 cycles (Hz)
Dimensions (L/W/H): 670x770x1203 mm Weight: 142 kg Total power requirement: 1,2 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 2000 KW, 2600 kVA, 400 V
2500 kVA Alternator / Generator End – 10 kV, 50 Hz, 1500 RPM Looking for a high-performance industrial alternator/generator? This 2500 kVA generator end is designed for reliable power generation in industrial plants, commercial facilities, and utility applications. Engineered for 10 kV output voltage, 50 Hz frequency, and 1500 RPM synchronous speed, this generator end delivers efficient and stable three-phase electricity. Key Specifications: Rated Power: 2000 Kw Output Voltage: 10 kV Frequency: 50 Hz Speed: 1500 RPM (synchronous operation) Phase: 3-phase, star/delta configurable Cooling System: Air-cooled or liquid-cooled options Excitation: Brushless or static excitation systems Insulation Class: Class F or H for continuous operation Voltage Regulation: ±1% High-Voltage Terminals: Suitable for 10 kV connections Features & Benefits: Standalon ...
Offer 08533 Measurement.- Richt. and welding plate Specifications: - Length approx. 2000 mm - Width approx. 1500 mm - Material thickness of the upper plate approx. 40 mm - Total height of the ribbed plate approx. 180 mm - Total height plate with steel base approx. 850 mm - Weight approx. 1800 kg
Used paddle mixer made by Steiner, model: MB 2000 with heating jacket. Usable capacity 2000 L. The Steiner MB 2000 with a usable capacity of 2000 litres is a professional device that can be useful for various applications in the food, chemical, cosmetic and pharmaceutical industries. It is equipped with a weighing system, a heating jacket and a paddle mixer with built-in Teflon scrapers, which enable accurate collection of the product from the bottom of the tank and prevent burning. The device can be helpful in a wide range of production processes, such as mixing, heating, defrosting or melting ingredients. By using cold water in the jacket instead of hot water or steam, it can also be used to cool products. Both the tank and the shaft with agitators are made of 304 acid-resistant steel. Teflon scrapers at the ends of the very sturdy agitators effectively collect the product f ...
WE OFFER AN NICE CONDITION LVD , WE CAN MAKE FOR CUSTOMER AS WELL START UP OF MACHINE INCLUDING TRAINING CUTTING CAPACITY 4KW CUTTING PLATES 6000 X 2000 MACHINE WAS COMPLETE OWERHAULED 2 YEARS AGO - SERVIS COST WAS 35000 EUR LAST SERVICE WAS MADE 6 MONTHS AGO MACHINE RUNNING IN THE PRODUCTION TILL FIRST WEEK IN MARCH 2022 WE OFFER MACHINE LOADED ON TRUCK. NEEDS 2 TRUCK FOR TRANSPORT, NORMAL TRUCK FOR CLIENT WE CAN ORGANIZE TRANSPORT AS WELL WE OFFER MACHINE FREE LOADED ON TRUCK. LASER- GE FANUC C4000 - MODEL E TRANSPORT FOR CUSTOMER WE CAN ORGANIZE AS WELL
Dear Sir or Madam, we have now available used transformer stations Year of construction : 2001-2002 Power : 1600KVA Primary voltage : 20kV Secondary voltage: 690V, Switching group: DYN5 Switchgear: SF6 total weight per station is 12.5 tons Dimensions: Length = Width = Height = Immediately ready for use and available, nationwide cheap delivery. If you have any further questions, Mr. Schmidt Techn. Purchasing is there for you, available Monday to Saturday from 8 a.m. to 10 p.m. and in case of emergency 24 hours
Plasma Cutter VCS 2000, HiPerformance Plasma HPR 260 XD and suction Filtercube 4H 7500 m³/h volume flow. To be visited in operation.
HOFLER HF 2000L hobber/gasher with both internal/external heads Year: 2013 Installed in 2020 Less that 200 working hours Table diameter: 1500mm Table loading: 18000kg Working stroke (external hobbing): 1760mm Working range above table (external hobbing): 150-1910mm Working range above table (internal hobbing): 250-1460mm Counter support-end face above table: 800-2300mm External toothing, Max: 2000mm Internal toothing, Max: 2400mm CNC control: Siemens 840D Complete weight: 61000kg Equipped with counter support
Specifications: - working length 3500 mm - Stand passage 3050 mm - max pressing force 2000 kN - Distance table / ram max. 480 mm - Stand projection 260 mm - Ram stroke approx. 300 mm - Lifting speeds - Downspeed idle max. 100 mm/sec - Boost speed 80 mm/sec - Downward pressing speed max. 10 mm/sec - Total drive power 25 kW - Space requirement approx. W 4500 x H 3150 x D 2100 mm - Weight approx. 16000 kg -with: - CNC control CYBELEC renewed in 2008 - controlled crowning device - controlled backgauge with height adjustment 5 - 1000 mm - hydr. Tool clamping - Upper tool + universal die tool - Material requirements - Two-hand control panel
table length: 2000 mm table width: 2000 mm table height: 200 mm bore: 28 mm weight: 1299 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
width of the strips: 75 mm band length: 2000 mm band speed: 30 - 34 m/sec total power requirement: 4,1 HP weight of the machine ca.: 75 Kg dimensions of the machine ca.: 1,2 x 0,5 x 0,85 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
You will find no hidden costs with us We always present the final amount on sales quotes if the contract is signed within the quote valid period. We always evaluate shipping costs from our warehouse in Poland. Laser welder LWH-2000-N The kit includes: - laser welder with cooling system - welding gun with adjustable focal length and set of accessories - fiber laser source MAX Photonics - automatic wire feeder - set of cords - starter kit of protective lenses and nozzles Specifications - Laser source output 2000 W - Laser wavelength 1064 nm - Welding speed up to 120 mm/s - Power supply 3x400 Hz Welding and cutting Otinus laser welders are supplied with a set of nozzles and protective lenses designed for metal welding and cutting. Therefore, the device is versatile, and helps to save money by eliminating the possible need to purchase, for example, a manual pla ...
Extraction dedusting Walther NOVA 2000 with 2 extraction arms mobile on wheels 2 pieces available Very good operational condition!
maximum number of results exceeded
please refine your search
