tin used for sale

Linen diving with salt-mounted and lye drain valve, 4-spring stand-boiler made of stainless steel incl. driving table with shelf and locking rollers suitable for tin size 580 x 780 mm, 4- or 5-row division mass in mm: 700 x 902 x 880 WxTxH; ready to go!

Professional steel shears for tin locksmiths, assembly plants, Teaching work pieces, particularly stable construction stable application with shear encoder made of encoded steel tooth lever translation lever securing via rotary spring knives made of high-quality tool steel, hoisted and ground continuously adjustable holder cuts of sheets, flat steel steel mm: 18 knife length mm: 175 Net weight kg: 47.5 room requirements approx.0.5x0.25x2 m; ready for use

Lawn Sweeper for PTO 540 rpm, working width 180 cm, double Sweeper roller system, hydraulic high dump, electrical. Remote control acting on solenoid valves, ew 1 hydraulic connection required. Tank contents approx. 3 m ³, rear axle 6 x frosted. Drawbar adjustable in height, illumination device com. StVZO. Machine is relatively little used, brushes and Tin in good condition with paint defects inside the tank and signs of use. Incl. operating instructions, parts list, and ABE. Type same Kugelmann KDH 150 (150 cm working width) also available and more with working widths from 90 to 170 cm. -Jacobis local, environmental & green care technology- Pre-owned equipment & sports square care, garden & landscape construction, cemetery technology & winter maintenance, reversing operations & decommissioning, environmental care, motors and more...

Magnetic drum MATEC For iron capture Length about 400 mm Drive about 0.37 kW Gearbox engine with tin slide Weight about 150 kg Built in 2018, new The machine is in very good condition, operational. Changes, errors, intermediate sales reserved! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Dough forming machine for small pastries MANOTRAD - manually operated - without electrics - mobile - optional with tin cart

Busbars for any shipbuilder or re-fit project. Produced following the highest European standards and availability rate FOR QUOTATION: INFO@AMP-POWER.NL Maximum Voltage 300 V AC/ 48V DC Number of terminal studs : 4 / 8 Terminal Type : 16 Stud Terminal stud torque : 15.82 Nm Continuos Rating : 545A AC / 600A DC Base Material: Reinforced Polycarbonate Bus Material : Tin-Plated Copper CDA 11 /UNS11000 Weight : 0.79 kg / 1.25 kg

Vertical baler Strautmann PP 1207 Manufacturer: Strautmann Type: PP 1207 Year of construction: 2002 Pressing force: 58 t Total connected load: 4.5 kW Height filling opening: 1145 mm Filling opening: 600 x 1190 mm Press cycle: 37 sec. Bale size: max. 1180 x 700 x 800 mm Bale weight: up to 350 kg Dimensions: 1844 x 1067 x 2868 mm Weight: 2400 kg Materials: paper, cardboard, cardboard, foil, plastic, PET bottles, tin cans Please note: All technical data refer to information provided by the manufacturer. We assume no liability for the information provided or any errors. The offers are subject to change, subject to prior sale and can be revoked at any time. Visits are possible by appointment. The sale takes place from the location, without guarantee and guarantee. Our payment term is 100% prepayment.

Rye bread divider. Weight range per piece: 0,4-1,2 kg; Capacity: 10-30 pcs/min ; Large hopper for 300 L; With 3000 mm conveyor and tin sensor; The divider is new. Client refused because of small amounts of dough.

Bread baking tin stick bread 90x17cm

I offer a mercury analyzer for sample analysis: - liquid (tin chloride reduction method), - solids (thermal method). Detection method: non-dispersive, double-beam atomic absorption system with generation of cold mercury vapor. Detection limit: 0.002ng Measuring range: 0 - 1000ng.

Engine. Guillotine Shears Impact Shears Tin Shears Scissors Cutting Manufacturer: KRAMER Model TM IIa 3000x4,5 max. cutting length 3050 mm max sheet thickness at ST 40 4.5 mm Distance between uprights 3050 mm Projection 130 mm Table width 360 mm Strokes per min 30 pcs. Hold-down device 16 pieces Manual backgauge travel 5 – 550 mm Engine power 7.5 kw Machine weight 4000 kg Space requirements: W 3480 mm D 3600 mm H 1400 mm Foot switch Back gauge front support arms Angle stop The machine is in good condition and ready for immediate use. Machine runs very quietly. Forklifts available, freely loaded trucks Cheap shipping possible Location of the machine 48324 Sendenhorst for enquiries 0157-35496006 The price is net plus 19% VAT.

grinding range: 8 - 32 mm sharp cornered angle min./max.: 90 - 140 Grad connected load: 230 V weight of the machine ca.: 16 Kg dimensions of the machine ca.: 0,43 x 0,24 x 0,24 m Drill grinding machine: Additional station for grinding back the drilling cutting surface (clearance angle) 25tk. Collets ER 40 are included in the scope of delivery, these are also suitable for clamping intermediate sizes. For grinding twist drills made of HSS and Hard metals with a TiN layer of 8 - 32 mm. Rotor with precision ball bearings guarantees smooth running. Vibration-free running thanks to its heavy weight and rubber feet. Sharpening angle adjustable for all common twist drills. Package dimensions: 430 x 240 x 240mm. Weight 16kg. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Guillotine shears used for tin shears; ; Manufacturer: ED PASKOWSKY SA; Type: ASS 65; Year: 1975; Working width max. 3050 mm; Sheet thickness max. 6.5 mm; Main motor power: 11 kW; 380 V; Dimensions approx. 3400 x 2000 x 1550 mm;

Optical Emission Spectrometers (OES) are characterized by the fact that they provide complete chemical analysis, even of critical alloying elements at low detection limits, which handheld XRF and LIBS devices cannot achieve: carbon, phosphorus, sulfur, boron, arsenic and tin in low-alloy, stainless steels and nitrogen in duplex steels. For this reason, spark spectrometry is the world's most reliable and widely used method for creating and verifying MTR's (Mill Testing Reports). Our instruments also meet the world's most stringent PMI testing requirements for metallurgical alloy chemistry, including API 5L testing, API RP578, ASME Section IX B& PV, ISO 17025 and A2LA standards.

REF-2261 AUTOMATIC CAN SEAMER SOMME NORA-313-VAC WITH VACUUM FILLING MACHINE 6 VALVES Automatic tin can seaming machine with 6-valve filling system Manufacturer: SOMME Model: NORA-313-VAC Can size: 3kg Output: 3,000 cans/ hour Vacuum pump dimensions: width 1,000mm, length 1,300mm, height 1,800mm Overall dimensions: width (including infeed belt) 3,600mm, length 1,900mm, height 2,000mm

Motorized tin snips make TRUMPF type OMS 450Machine -No: 94278Technical specifications:Cutting capacity: 4.5 mmCutting speed: up to 4 m/min.small radius to be cut: 30 mmNumber of cuts per minute: 1400Power: 1100WPower connection: 380 V / 50 HzWeight approx.: 100 kgExternal dimensions: 350 x 2500 x 1100 mmWith- Pillarused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

REF-0 SOMME 323 CAN SEAMER WITH 5 HEADS AND VACUUM FILLING SYSTEM 20 VALVES Automatic tin can seaming machine with 5 seaming heads. Fitted with a 20-valve vacuum filling unit. Manufacturer: SOMME Model: 323 Can size: Ø 73mm (easy-open lids) Overall dimensions: length 3,400mm, width 2,800mm, height 2,200mm

REF-2259 SOMME DIANA-363-VAC AUTOMATIC CAN SEAMER WITH 6 HEADS AND SOMME 21-VALVE VACUUM FILLING SYSTEM Automatic tin can seaming machine with 6 seaming heads. Fitted with a 21-valve vacuum filling unit. Manufacturer: SOMME. Model: Diana-363-VAC Output: 12-15,000 Cans/ hour Can size: Ø 73mm. Overall dimensions: length 4,200mm, width 2,000mm, height 2,200mm

-Stainless steel tin trolley for Miwe Rollin 60x60 rotary oven -with 18 editions -optionally with sheets

pressure: 80,0 t punching cross-cut in cmm: 31,0 in 25 mm shear: flat material: 500x18 / 300x22 mm L-beam: 150 x 12 mm round bar steel: 50 + 25 mm square edge steel: 50 + 30 mm throat: 510 mm blade length: 500 mm work height max.: ca. 1.100 mm total power requirement: 7,5 kW weight of the machine ca.: 3200 kg dimensions of the machine ca.: 2000 x 1000 x 2100 mm from a maintenance workshop Furnishing: - Robust electro-hydraulic combined profile steel shears - Notcher, hole punch, bar steel knife, profile knife and tin snips - Stop table at the hole punch, with blank holder - Stop table at the notcher - 2x floating footswitches - Stroke adjustment for fast stroke sequence - 1x PEDDINGHAUS contact length stop: 1.000 mm - Safety devices - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Rheon VX is a series of stress free dividers, which can divide most of doughs - even extremely moist. From rye tin bread to italian ciabatta flat bread (see photos for examples and our test products). The machine has been fully renovated in 2020 and is ready for work! Weight range: One row: 100 - 2000 gr two rows: 30 - 1500 gr Length range: 75 - 999 mm Max. cutting speed per row: 20 cuts per minute. If you find the machine interesting, let me know via phone, mail or whatsapp!

Rheon VX is a series of stress free dividers, which can divide most of doughs - even extremely moist. From rye tin bread to italian ciabatta flat bread (see photos for examples and our test products). The machine has been fully renovated and is ready for work! Weight range: One row: 150 - 1200 gr two rows: 50 - 500 gr Length range: 75 - 999 mm Max. cutting speed per row: 20 cuts per minute. Capacity: 400 kg/h If you find the machine interesting, let me know via phone, mail or whatsapp!

Tubular cable lug, crimped cable lug, 49 pieces KLAUKE 7R8 KL70/8 Nominal cross-section : 70 mm² Screw size: M8 Material: Copper, tin-plated New ! Dimensions ( cable lug ): 53 x 24 x 16 mm Dimensions ( packaging ): 170 x 145 x 80 mm

Tubular cable lug, crimped cable lug, 46 pieces KLAUKE 7R10 KL70/10 Nominal cross-section : 70 mm² Screw size: M10 Material: Copper, tin-plated New ! Dimensions ( Terminal ): 57 x 24 x 18 mm Dimensions ( packaging ): 170 x 145 x 80 mm

Press for tin cans, Fabr. Josto

Tubular cable lug, crimped cable lug, 34 pieces KLAUKE 8R10 KL95/10 Nominal cross-section : 95 mm² Screw size: M10 Material: Copper, tin-plated New ! Dimensions ( Terminal ): 60 x 26 x 18 mm Dimensions ( packaging ): 170 x 145 x 80 mm

Screw bridge, fixed bridge, complete, 60 pieces PHOENIX CONTACT FB 10-8 02 02 17 0 ( 0202170 ) number of poles: 10 pitch: 8 mm Material: Copper, tin-plated New ! Dimensions ( single clamp ): 80 x 8 x 7 mm Dimensions ( packaging ): 130 x 90 x 100 mm

Capsule shriveling Cavino Gatti / Ítalien Year of construction 1996 Max. 3,000 bph Bottles 0.25 to 1.00 L Aluminum + Tin Foil + Thermal Capsules Further information and price on request

Ground tape set, flat weave tape, grounding tape PAGUS conductor nominal cross-section: 50 mm² conductor material: copper, tin-plated holes: Ø 6 / 9 mm distance between holes: 1145 mm Cable width: approx. 28 mm Cable height: approx. 3 mm cable set consists of 4 cables ! unused ! Dimensions(single cable): 1180 x 28 x 3 mm Dimensions: 100 x 80 x 20 mm

Replacement knife set for guillotine shears, tin shears, 2 pieces PAGUS Knife length: 2050 mm Knife thickness: 15 / 16 mm cross-section: 58 x 15 mm / 139 x 16 mm all threads M12 x 1.75 Replacement knife set consists of 2x upper and 2x lower knives ! Other quantities on request ! New ! Dimensions ( Packaging ): 2700 x 200 x 275 mm

Nibbling machine, nibbler, nibbler, tin snips, circular shears -Power: 900 watts -Max. Cutting capacity: 3.25 mm -Dimensions: 500/220/H230 mm -Weight: 5.5 kg

Nibbling machine, nibbler, nibbler, tin snips, circular shears -Power: 900 watts -Max. Cutting capacity: 3.25 mm -Dimensions: 500/220/H230 mm -Weight: 5 kg

Hand lever shears, long-knife sheet metal and round steel shears, lever shears, long-knife sheet metal shears -Manufacturer: Victoria, long-knife tin snips on a mobile stand -Blade insert length: approx. 350 mm -Sheet steel: up to approx. 4 mm -Rectangular profile: up to approx. 7 mm -Total dimensions: 1030/500/H1900 mm -Weight: 109 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears -Blade insert length: 200 mm -Steel sheet: up to 7 mm -Flat/band iron: up to 100x9 mm -Round steel: up to 20 mm -Rectangular profile: up to . 18x18mm -Lever arm: with rack and pinion translation -Total dimensions: 540/180/H1570 mm -Transport dimension: 1250/180/H490 mm -Weight: 44kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Hand lever snips: tin snips with stop and stable base -Blade insert length: Approx. 160 mm -Lever arm: with rack and pinion translation -Hold-down device: continuously adjustable -Total dimensions: 1000/780/H1870 mm -Transport dimension: 1000/780/H1300 mm -Weight: 100 kg

Hand lever shears, long-knife sheet metal and round steel shears, lever shears, long-knife sheet metal shears -Manufacturer: Victoria, Long Knife Tin Snips -Blade insert length: approx. 350 mm -Sheet steel: up to approx. 4 mm -Rectangular profile: up to approx. 7 mm -Total dimensions: 670/180/H1260 mm -Weight: 55 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears -Blade insert length: 200 mm -Round steel: up to approx. 20 mm -Rectangular profile: up to approx. 19x19 mm -Lever arm: with rack and pinion translation -Total dimensions: 455/170/H1540 mm -Transport dimension: 1230/170/H440 mm -Weight: 49 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears -Blade insert length: 150 mm -Round steel: up to 12 mm -Lever arm: with locking spring -hold-down: -Total dimensions: 320/120/H1260 mm -Transport dimension: 990/120/H310 mm -Weight: 12 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears type 3 S / 4 L -Blade insert length: approx.300 mm -Steel sheet: up to 4 mm -Flat/band iron: up to 70x6 mm -Round steel: up to 13 mm -Cutting capacity: see photo nameplate -Hold-down device: continuously adjustable -Number: 2x lever scissors available -Price per piece -Total dimensions: 500/160/H1480 mm / 500/160/H1180 mm -Transport dimension: 1180/160/H430 mm -Weight: 32/30 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears type 3/5 R -Blade insert length: 200 mm -Steel sheet: up to 5 mm -Flat/band iron: up to 60x6 mm -Round steel: up to 13 mm -Cutting capacity: see photo nameplate -Total dimensions: 380/160/H1310 mm -Transport dimension: 970/160/H470 mm -Weight: 23 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears type 3S / 6 R -Blade insert length: 200 mm -Steel sheet: up to 6 mm -Flat/band iron: up to 70x7 mm -Round steel: up to 13 mm -Cutting capacity: see photo nameplate -hold-down: -Total dimensions: 385/160/H1500 mm -Transport dimension: 1160/160/H400 mm -Weight: 24 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears type 3/5 R -Blade insert length: 200 mm -Steel sheet: up to 8 mm -hold-down: -Total dimensions: 385/160/H1280 mm -Transport dimension: 960/160/H390 mm -Weight: 22 kg

Hand lever shears, long knife sheet metal and round steel shears, lever shears -Manufacturer: Mubea, tin and round steel shears -Blade insert length: 280 mm -Round steel: up to 14 mm -Total dimensions: 500/160/H1250 mm -Transport dimension: 930/160/H420 mm -Weight: 30 kg

Nibbling machine, nibbler, nibbler, tin snips, circular shears -Power: 680 watts -Max. Cutting capacity: 2.5 mm -Dimensions: 300/100/H300 mm -Weight: 4.6 kg

Nibbling machine, nibbler, nibbler, tin snips, circular shears -Power: 330 watts -Voltage: 220 V -Max. Cutting capacity: 2 mm -Dimensions: 280/60/H150 mm -Weight: 2.3 kg

Nibbling machine, nibbler, nibbler, tin snips, circular shears -Power: 680 watts -Voltage: 220 V -Max. Cutting capacity: 3.5 mm -Dimensions: 290/85/H280 mm -Weight: 5 kg

Nibbling machine, nibbler, nibbler, tin snips, circular shears -Power: 1800 watts -Voltage: 220 V -Max. Cutting capacity: 4.5 mm -Dimensions: 570/220/H250 mm -Weight: 10.5 kg

Nibbling machine, nibbler, nibbler, tin snips, circular shears -Power: 680 watts -Max. Cutting capacity: 2.5 mm -Number: 1x nibbling machines available -Price: per piece -Dimensions: 300/95/H310 mm -Weight: 4.5 kg

Forge grab, manipulator forge grab, sheet metal clamp, sheet metal claw, beam clamp, beam claw, sheet metal grab, material grab, material grab -Tin claws -Wingspan: 0 to 250mm -Load capacity: 1,000 kg -Number: 1x available -Dimensions: 730/240/H860 mm -Weight: 118kg

Tin shear attachment for drill, sheet metal nibble NAREX NP2 sheet thickness: max. 2 mm necessary drill collar: Ø 42 mm drive width: 17 mm New ! Dimensions: 200 x 200 x 80 mm