soldering used for sale

Stringer, solar stringer, soldering machine for solar cells, A09-209-rus ATN, used Semi automated stringer Technical specifications: - Manual feed of the solar modules - 1 soldering station - Program assisted automatic soldering process - Adjustable soldering area - E Declaration of Conformity, Operating Instructions, Plans and Programs, - Compressed air connection 6 bar, power connection 16A, 400 / 230V, 6KW Very good condition: With the handstringer were max. 10,000 soldering operations carried out the max. Including the inlay work only about 50 operating hours. The stringer was overhauled and is in mint condition. It is a private sale of one of our customers.

Soldering station, soldering iron, chip soldering system, workshop soldering iron, hammer soldering iron -Power: 220 V 300 watts -Weight: 1 kg

electric soldering iron, soldering device, hammer soldering iron BÖHME LEIPZIG Type B 2030 Power: 0.7 kW ( 700 watts ) Connection voltage: 220 V AC approx. 1.4 m connection cable soldering tip: 40 mm, chisel-shaped New ! Dimensions ( without cable ): 350 x 215 x 65 mm,

electric soldering iron, soldering device, for soldering machines ERSA Type 601 Power: 0.08 kW ( 80 watts ) Connection voltage: 24 V DC temperature: max. 350 °C approx. 0.35 m Connection cable Soldering tip: 52 mm ( 30 / 10 / 12 mm ), cone-shaped used, tested ! dimensions ( without cable ): 195 x 100 x 55 mm,

Soldering station, soldering iron, chip solder, soldering system -Temperature adjustable: 100-375 ° -Dimensions: 200/105 / H90 mm -Weight: 2.7 kg

max. soldering width/passage height/board length: 340mm/100mm/500mm. max. wave height: 7mm, solder volume SnPb/SnAgCu: approx. 185kg/150kg, heating time from 20°C to 250°C: approx. 90 min. Preheating zones: 1, preheating power: 3kW, max. preheating temperature: 420°C. Soldering frame transport width: 417mm, transport angle manually adjustable: 6-8°, transport speed min.-max.: 0.3-2.0 m/min. Including 2 soldering frames: Profile: 18mm, lug L: 381mm. On-site inspection is possible.

ERSA HOTFLOW - 7 Soldering furnace / tunnel dryer / belt dryer / continuous dryer Type: HOTFLOW – 7 Convection oven as soldering oven / tunnel dryer / belt dryer / continuous dryer for drying sheet materials on top and bottom. 4 heating zones at the top, 4 heating zones at the bottom, for drying on both sides. Rolling bars at a distance of approx. 4.5 cm on 2 transport chains as a support for plates Temperature range from 20° to 300°C Rated power Pn = 72 KW Nominal current In = 106 A Voltage: 3 x 400 / 230V Back-up fuse: 3 x 125 A Frequency 50 Hz Power: 67 KW Year of construction: 2000 Dimensions: Length: 5250 mm Width: 1300 mm Height: 1750 mm (incl. warning light) Height: 1450 mm (without warning light) Dry section: Length of heating zones: 3300 mm Transport width: 500 mm Exhaust pipes and additional fan can be supplied. Circuit diagrams are ...

Universal soldering and welding torch ROTHENBERGER Allgas 2000 with oxygen and propane gas cylinder mobile Dimensions: 440 x 440 x850 mm

Soldering button, 12 pieces PENDAR 10x SI 1103 5322 A1 276 14279 2x SF 1103 5322 A1 276 14278 5x button button 5322 A1 414 14065 New Dimensions ( packaging ): 240 x 130 x 65 mm

Connected load: 43,000W, including exhaust air box for the fluxing area, tubular fan shaft, 80 soldering frames, various mounting materials, 3 fluxer nozzles, 5 fluxer filters and documentation, an unused PCS-96 control unit is also available, on-site inspection is possible.

Type WLG Made in Germany 1981 y.

- 1 blower built 1987: 800 mbar, 24.2 m3/min, 45 kW, 500 V; - 1 blower built 1993: 400 mbar, 24.2 m3/min, 45 kW, 500 V; - 1 blower built 2007: 700 mbar, 21.8 m3 rpm, 45 kW, 500 V

Manufacturer: Scansonic Type: AL01 Condition: refurbished, since then unused and professionally stored in the manufacturer's suitcase Wavelengths: 900 ... 1030 nm; 1064 nm, 1080 nm to 4 kW Illustrations: 2.0:1 - 2.5:1 - 3.2:1 - 4.0:1 - 5.3:1 Fiber plug: Trumpf B or Type D (LLK Auto) Laser: CW laser up to 4 kW Working range height (Z): ± 5 mm Robot adaptation: any Repaired/replaced: - Lens - Compression spring - Protective spring - Cover - Beam aperture - Shaft spring - Fiber coupling firing In addition, the device was cleaned, adjusted and force-normalized.

Connected load: 18kW, was overhauled in 2017, an inspection is possible.

Max. circuit board dimensions: 330x420-400x495mm, conveyor speed: 0-2.5m/min, an on-site inspection is possible.

Connected load: 41kW, an inspection is possible.

Multipurpose propane solderer BAT PROPY 1 without connection hose and pressure reducer in metal case New ! Dimensions: 250 x 220 x 75 mm

Working width: 250mm, transport angle: 4-7°, transport speed: 0.3-2.5m/min, solder volume: 120kg, preheating length: 800mm, connected load: 8kW, length: 1980mm, width: 770mm, height: 1430mm, weight: 250kg, filled with lead-free solder, with documentation, on-site inspection is possible.

Multipurpose propane solderer BAT PROPY 2 with connection hose and pressure reducer in metal case New ! Dimensions: 250 x 220 x 75 mm,

Max. solder width: 340mm, connected load: 8000W, an inspection is possible.

Max. PCB dimensions: 410x410mm, max. PCB weight: 5kg, connected load: 1.5-6.4kW, software: Windows 98, with documentation, the machine should be overhauled, there are various defects.

Description: Composed of: Welding port station PHILIPS SBC 345  ,without welding rod. Material preheating station  ,GOOT POT 21C. Approx. Onsite Dimension. (l x w x h): 300 x 300 x 200 mm, weight approx.: 5 kg

The FORNI INDUSTRIALI FIBEX COMBI 6GX-10.130-7110.2E.270 brazing furnace was built by the Italian company Forni Industriali Heat Treating Plants in 2007. The furnace is used for soldering steel elements with solder paste at temperatures up to 1120 degrees Celsius. At the entrance and exit of the furnace, two pairs of gas burners (so-called safety pilots) are installed to prevent the escape of the protective atmosphere outside the furnace. Electric heaters powered by thyristor temperature regulators are responsible for the proper temperature in the furnace. The belt furnace has a conveyor speed adjustment in the range from 0 to 500 mm / min, and the working length of the soldering zone is 7100 mm. The furnace for brazing steel elements was modernized in 2021 - the thermal insulation and the cooling module for sections 1 and 2 were replaced. The cost of the modernization was 70,000 Euro.  ...

00790-2 R&D department for Lithium-ion battery manufacturing will be COMPLETELY dissolved The value of these fixed assets amounted to approximately 7.5 million euros at the time of new acquisition. Manufacturer: Werner Mathis AG Manufacturer: Eirich Gustav GmbH (see also List1 page 6 EL5 Profi-Plus Manufacturer: Robust Habicht Manufacturer: Digatron Manufacturer: Coherent Rofin B.V. Manufacturer: Keyence Inventory name Filling station: Glovebox Braun with scale, cooling unit, etc. Exhaust air scrubber FRIDURIT Neutralization plant FRIATEC Rena Technologies GmbH Lauda Dr. R. Wobser GmbH & Co. KG AFA Glass furnace Ball fall viscometer Solder fume hood Profilometer Battery test system BaSyTec CTS 32 channels CTS 1666 Battery test system BaSyTec CTS 32 channels CTS 1667 Battery test system BaSyTec CTS 32 channels CTS 1668 Vacuum pump Measuring  ...

Induction soldering machine FDF Fritz DusseldorfBuilt in 1990 consisting of:1.) Soldering table type LT No. 25-18080.90 built in 1990with 1 lifting station projection: 400 mmDistance table - soldering unit: 650 mmelec. Connection: 380 V, 63 AConnected load: 35 kVADimensions: 1600 x 1200 x 1900 mm2.) Stationary parallel resonant circuit inverter type PSU 30-10Fabr. -No: 65.18601-90Max. Power: 30 kWFrequency range: 8 - 10 kHZConnected load: 41 kVAelectrical connection: 380 VDimensions: 1100 x 1100 x 2200 mm3.) Refrigeration unit VICARB Germany, built in 1987Machine -No: D 1044Operating pressure: 10 barPower: 56 kWWeight approx .: 186 kgDimensions: 1200 x 1200 x 1030 mmTotal operating time so far: 7770 operating hoursequipped with:- adjustable heating time- adjustable heating cycles- adjustable pause timelittle used, in good conditionPrice on request.Delivery: ex warehouse or location free  ...

Central extraction system for soldering stations and welding workplaces make KEMPER type 91890Fabr. -No: 300374-03 built in 1998for 3 - 7 jobs,The material liquefied during the soldering process releases smoke, gases and aerosols, which must be sucked off. The Kemper extraction system was specially designed for use at soldering stations. He sucks the substances punctiform.Filtering in 3 stages: pre-filter, suspended particle filter,: Activated Carbon FilterFlow rate: 700 m3 / hMax. stat. Pressing: 1600 PaConnection voltage: 380VRated current: 2.5 AMotor power: 1,1 kWDuty cycle: 100% EDWith:- Control panel and electronic filter monitoring- Monitoring the activated carbon filter by means of LED chainused, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We  ...

Wave soldering machine make ATF type 20-33Year 1995, make -No: 0352330795Fluxer (spray fluxer)Compressed air consumption approx. 80 l / min depending on the setting.process width: 330 mmFluxer (foam fluxer)Compressed air consumption approx. 60 l / min depending on the setting.Process width: 330 mmMax. Flux capacity: 4.0 lMax. Foam height: 12 mmpreheatingRadiator per machine: 8Power consumption: 4.0 / 7.9 kWTemperature range Ambient temperature: -300 ° CTemperature sensor: Type J Fe-CuNisolder potPump motor: 24 V DC 1.3 AMax. Soldering temperature: 30 ° CHeating elements: 9 x 500 WHeating time approx: 2.0 hoursTemperature sensor: Type J Fe-CuNiLot quantity: 220 kgconveyor beltMax. PCB size: 335 x 420 mmDrive motor: 24 V DC 1.5 ABelt speed: 0 - 2.5 m / min.adjustable transport angle: 5 - 9 °Max. Process height: 120 mmSpecification machineDimensions approx: 1600 x 1000 x 1360 mmExtractio ...

ERSA HOTFLOW - 7 Tunnel Dryer / Belt Dryer / Continuous Dryer Type: HOTFLOW – 7 Convection oven as a tunnel dryer / belt dryer / continuous dryer for drying plate materials on the top and bottom. 4 heating zones at the top, 4 heating zones at the bottom, for drying on both sides. Rolling rods at a distance of approx. 4.5 cm on 2 transport chains as a support for plates Temperature range from 20° to 300°C Nominal power Pn = 72 KW Nominal current In = 106 A Voltage: 3 x 400 / 230V Back-up fuse: 3 x 125 A Frequency 50 Hz Power 67 KW Year of construction 2000 Dimensions: Length: 5250 mm Width: 1300 mm Height: 1750 mm (incl. warning light) Height: 1450 mm (Without warning light) Dry section: Length of heating zones: 3300 mm Transport width: 500 mm For possible use as a soldering oven – soldering machine – reflow oven, a cooling zone must be set up.  ...

Soldering table Ceramics: 340 x 390 mm Equipped with: 2 Gasfackels Weight: 300 kg Table Lxwxh: 2000 x 900 x 1750 mm

Machine type MIG/MAG inverter welding system without BiPower Make Merkle Type MobiMIG 280 K Plant No. 123.035 Connection voltage 3 x 400 volts Adjustment range 25 - 280 amperes Switch-on time 35% ED at 280 amperes 60% ED at 240 amperes Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version of portable assembly line Wire feed gearbox 4-wheel transmission DV 26 Fuse 16 Ampere Dimensions L x W x H 470 x 255 x 545 mm Special accessories ColdMIG welding process, e-welding MIG soldering, filler wire welding Weight 27 kg Age 2 years Condition workshop-tested, very good, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SBT 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer Argon w ...

TECHNICAL DATA This furnace system is for recrystallization, normalization, soft annealing, stress relief, annealing and conditionally suitable for soldering. belt width: 1000 mm working height: 300 mm (over belt) heated length: 4250 mm electrical heating power: 300 kW heating zones: 4 heating temperature: 900 – 1120°C belt speed: 6 – 60 m/h (continuously adjustable) nominal connected load: 310 kW natural gas consumption: 50 Nm3/h natural gas pressure: 30 – 50 mbar nitrogen consumption: 70 Nm3/h – on purging nitrogen pressure: 100 mbar emergency cooling water pressure: 4-6 bar furnace length: 25298 mm furnace width: 2200 mm furnace height: 2800 mm exhaust gas quantity: 1200 m3 / h

Machine type MIG/MAG inverter welding system without BiPower Make Merkle Type MobiMIG 280 K Connection voltage 3 x 400 volts Adjustment range 25 - 280 amperes Switch-on time 35% ED at 280 amperes 60% ED at 240 amperes Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version of portable assembly line Wire feed gearbox 4-wheel transmission DV 26 Fuse 16 Ampere Dimensions L x W x H 470 x 255 x 545 mm Special accessories ColdMIG welding process, e-welding MIG soldering, filler wire welding Weight 27 kg Age 12 months Condition workshop-tested, very good, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SBT 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer Argon with 2 pressure gau ...

Machine type MIG/MAG inverter welding system Make Merkle Type MobiMIG 180 K Connection voltage 1 x 230 volts Adjustment range 25 - 180 amperes Switch-on time 20% ED at 180 amperes 60% ED at 110 amperes Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version of portable assembly line Wire feed gearbox 2-wheel transmission Fuse 16 Ampere Dimensions L x W x H 450 x 210 x 480 mm Special accessories ColdMIG welding process E-welding, MIG soldering Filling wire welding Weight 17 kg Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SBT 157 G, 3 mtr. Long 1 piece ground cable 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-200 coil, 5 kg 1 can  ...

Machine type MIG/MAG inverter welding system with bi-power setup Make Merkle Type MobiMIG 280 K - BiPower Connection voltage 230/400 volts Adjustment range 25 - 280 amperes Switch-on time 35% ED at 280 amperes 60% ED at 240 amperes Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version of portable assembly line Wire feed gearbox 4-wheel transmission DV 26 Fuse 16 Ampere Dimensions L x W x H 470 x 255 x 545 mm Special accessories ColdMIG welding process, e-welding MIG soldering, filler wire welding Bi-Power Setup Weight 27 kg Age 12 months Condition workshop-tested, as new, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories 1 piece welding torch SBT 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reduc ...

The IQ control keeps the set air flow the same during runtime. MA-201030 Optional: In stainless steel, , hose set, VOC, filter change signal, start/ stop via external 24V - the compact device offers many areas of application - the filters used are characterized by a long service life - the two filter cassettes separate dust, fine dust and gases - the air flow is 850 m³/h - the dimensions are 1197 mm x 600 mm x 790mm (HxLxW) - Weight 140 kg - Noise level less than 61 dBA Options: - Suction hose in the necessary length - Connection sleeves - various suction nozzles Typical applications : Marking laser Engraving laser Cutting lasers Welding laser Soldering and welding fumes

with pre-filter and activated carbon filter for fine dusts and gases produced e.B. during laser processing or soldering work Dimensions HxWxD 743x360x360 mm Housing - dark grey powder-coated Airflow - 300 m³/h elekt. Data 230V, 50Hz , 12.5A full load current / 3.3 kW Noise level less than 60 dBA Weight 45 kg Warranty 1 year ( filter excluded ) VAT is shown, EXW Options - Hose in desired length - Connection sleeves - various suction nozzles

Suction AD-Oracle IQ from Bofa - New : The IQ control keeps the set air flow the same during runtime. Optional: In stainless steel, , hose set, VOC, filter change signal, start/ stop via external 24V - the compact device offers many areas of application - the filters used are characterized by a long service life - the two filter cassettes separate dust, fine dust and gases - the air flow is 380 m³/h - the dimensions are 980 mm x 430 mm x 430 mm (HxWxD) - Weight 68 kg - Noise level less than 60 dBA Options: - Suction hose in the necessary length - Connection sleeves - various suction nozzles Typical applications : Marking laser Engraving laser Cutting lasers Welding laser Soldering and welding fumes

Extraction AD-Oracle from Bofa - new : with start/stop via external 24V optional: in stainless steel, , hose set, VOC, filter change signal - the compact device offers many areas of application - the filters used are characterized by a long service life - the two filter cassettes separate dust, fine dusts and gases - the air flow is 380 m³/h - the dimensions are 980 mm x 430 mm x 430 mm (HxWxD) Typical applications : Marking laser Engraving laser Cutting lasers Welding laser Soldering and welding smoke

Machine type MIG/MAG inverter welding system Böhler brand Type Uranos 2000 SMC Connection voltage 1 x 230 Volt Setting range 5 – 200 amps Duty cycle 35 % ED at 200 amps 60% ED at 160 amps 100% ED at 130 amps Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version portable mounting system Wire feed gearbox 2-roller gearbox Fuse 16 amps Dimensions L x W x H 500 x 210 x 400 mm Special accessories TIG DC welding without HF E-welding, MIG soldering Weight 13 kg Age 6 months Condition workshop tested, as new, incl. UVV test report Scope of delivery welding system with the following accessories: 1 piece welding torch, 3 mtr. long 1 piece ground cable 1 piece pressure reducer argon with 2 pressure gauges 1 roll of welding wire D-200 coil, 5 kg 1 can of non-stick spray 1 piece ...

You will find no hidden costs with us We always present the final amount on sales quotes if the contract is signed within the quote valid period. We always evaluate shipping costs from our warehouse in Poland. Laser welder LWH-2000-N The kit includes: - laser welder with cooling system - welding gun with adjustable focal length and set of accessories - fiber laser source MAX Photonics - automatic wire feeder - set of cords - starter kit of protective lenses and nozzles Specifications - Laser source output 2000 W - Laser wavelength 1064 nm - Welding speed up to 120 mm/s - Power supply 3x400 Hz Welding and cutting Otinus laser welders are supplied with a set of nozzles and protective lenses designed for metal welding and cutting. Therefore, the device is versatile, and helps to save money by eliminating the possible need to purchase, for example, a manual pla ...

Welding fume extraction, soldering extraction, laboratory extraction High vacuum Torch extraction FUMATOR-APPARATEBAU HEINZ WAGNER Type Minivac 250 D series. No. 2902619 Year of construction 2004 Unit air volume flow max. 250 m3/h Minimum air volume flow rate min. 100 m3/h Separation efficiency 99.97 % Welding fume class W3 Motor power approx. 0.75 kW Mains connection 230 volts, 50 Hz - Suction power infinitely adjustable - 2 pieces Suction connections 45 mm - mechanical air filter (used) - mobile underframe with 4 fixed castors, platform roller Space requirement L x W x H 700 x 500 x 600 mm Weight suction 35 kg Weight platform roller 7 kg good condition; used

volume capacity: 1600 m3/h feed volume: 99,9 % length: 3.000 Absaugschlauch mm motor: 230 Volt motor: 1,1 KW weight: 80,0 kg range L-W-H: 580 x 580 x 900 mm Description: The filtoo filter device newly developed by TEKA is a mobile filter system that many Tasks in the field of filtration of Smoking, dusts and gases can be used. Also suitable for high-alloy steels (stainless steel). (the device was based on DIN EN ISO 15012-1 (2005) tested and is IFA (formerly BGIA) certified (IFA No. 201020469/1140) for welding smoke class W3 (degree of separation:> 99.9%)) Where can the SIG 230 filtoo be used? - at welding workplaces - in the workshop area - for soldering applications - with restorers - in locksmiths Furnishing: - BGIA - certified suction and filter system IFA 1005030 for suction to hochleg. Steels & non-ferrous metals - Operating instructions in German optional equipment for a surchar ...

mobile welding smoke filter, welding smoke extraction, soldering smoke extraction -Drive: 2.2 KW -Extraction arm: 3000 mm -Connection: 380 V 50 Hz -Dimensions: 860/1250/H1950 mm -Weight: 120 kg

mobile welding smoke filter, welding smoke extraction, soldering smoke extraction -Drive: 1.6 kW -Connection: 220 V 50 Hz -Weight: 46 kg

Training device for circuit construction HPS SYSTEM TECHNIK TYPE 3530 Universal training device for building circuits with commercially available components Any operating voltage can be connected, therefore very flexible Fast test setup without soldering used, tested ! Dimensions: 300 x 270 x 100 mm

Relay socket, double, 2 pieces ELEKTRO-APPARATE-WERKE BERLIN-TREPTOW RELOG-System Type series: 2RHxx / 4RHxx PL - No.: 739197000 250 V AC/DC 5 A TGL 26048 Price for 2 pieces ! New ! Dimensions(single socket, without soldering lugs): 80 x 58 x 16 mm

Wire electrode, welding wire, copper base MIG solid wire electrode for soldering copper, copper-silicon, copper-zinc alloys -Net weight: 10.9 kg -Number: 1x package available -Price: per package -Weight complete: 11.5 kg/package

Extractor fan, welding fume filter, welding fume extraction, soldering fume extraction, small dust extractor, -Manufacturer: Esta, small dust extractor extraction fan for smoke extraction -Type: Esta 100 -Drive: 0.55 kW / 2850 rpm -Fan wheel: Ø 280 mm -Connection: Ø 100 mm -Volume flow: Max. 1000 m³/h -Dimensions: 425/420/H845 mm -Weight: 35 kg

Extraction fan, welding fume extraction, soldering fume extraction -Manufacturer: Kemper, exhaust fan for welding fume extraction -Drive: 0.75 kW -Fan wheel: Ø 280 mm -Inlet: Ø 316 mm, bolt circle Ø 330 mm M6 -Outlet: Ø 170 mm -Dimensions: 440/420/H375 mm -Weight: 20 kg

Controlled cross table, cross sliding table, clamping table, clamping plate with T-slots, clamping angle, cross table NC, linear robot, coordinate table -Controlled cross table: was used as a soldering station -Manufacturer: Walko, cross table NC type PNC 500 -Table surface: 600 x 300 mm -Travel approx.: X 500 mm / Y 350 mm -Dimensions: 1050/1030/H1530 mm -Weight: 240 kg