rubber injection used for sale

clamping force: 450 kN injection volume: 135 cm³ screw diameter: 35 mm platen size: 600 x 400 mm Condition: used, Specification: C-frame injection moulding machine for TPE - used clamping unit: - clamping force: 450 kN - heating platen size: 600 x 400 mm - sliding table: yes - Clamping direction: from below - Ejector / lifter: Up + Lo Injection unit: - Injection volume max.: 135 cm³ - Screw diameter: 35 mm - Connected load: 3x 400 V, 50 Hz - Weight approx.: 5,500 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 800 kN injection volume: 154 cm³ screw diameter: 35 mm platen size: 430 x 660 mm Condition: second-hand, Specification: C-frame injection moulding machine - second-hand Clamping unit: - Clamping force: 800 kN - Mould mounting area: 430 x 660 mm - Clamping/opening stroke: 450 mm - Maximum mould installation height without heating plates: 300 mm - Maximum plate spacing without heating plates: 750 mm - Clamping direction: from below - Ejector stroke: 130 mm - Ejector force: 40 kN Injection unit: - Increased injection pressure: 2,180 bar - Maximum injection volume: 154 cm³ - Screw diameter: 35 mm - Screw length: 20D - Maximum screw speed: 20–400 rpm - Metering stroke: 160 mm - Injection: from above - Nozzle stroke: 250 mm - Voltage: 3 × 400 V, 50 Hz, N, PE - Pump drive power:  ...

CONVEYOR BELTS, for waste material and more, sturdy steel structure, constructed in a workman like manner, Italian quality and components, can be lined in PVC, RUBBER or SHUTTER TYPE BARS, Can be prepared and fitted for METAL DETECTORS, and completed with OVERBELT METAL SEPARATORS, Size and characteristics bespoke to the project., Just fill your enquiry with the following data:, - Materials to be transported (photos appreciated), - Quantity in Tons/h, - required working width, - total length, - horizontal length, - diagonal length, - heigh of discharging point, - if prepared for metal detecto, - if fitted with metal detector (in this case, please add maximum contamination size), - if positioned in covered/uncovered place, We will send you a most targeted offer.

1) Vertical Rubber Molding Machine Manufacturer: Rutil Model: 2000/250 RS SX-F Stations: 1 Clamping Force: 500 Ton Heating Platens Dimensions: 520x650 mm Max Shot Volume: 2000 cc Max Daylight: 450 mm Minimal Mould Height: 100 mm 2) Vertical Rubber Molding Machine / NEEDS REPAIR - Manufacturer: Rutil - Model: MP3 700/150 - Stations: 3 - Clamping Force: 150 Ton - Heating Platens Dimensions: 420x500 mm - Max Shot Volume: 700 cc - Max Daylight: 400 mm - Minimal Mould Height: 140 mm 3) Vertical Rubber Molding Machine NEEDS REPAIR - Manufacturer: Rutil - Model: 680/150 RS - Stations: 1 - Clamping Force: 150 Ton - Heating Platens Dimensions: 430x500 mm - Max Shot Volume: 680 cc - Max Daylight: 400 mm - Minimal Mould Height: 70 mm 4) Vertical Rubber Molding Machine - Manufacturer: Rutil - Model: 680/150 RS - Stations: 1 - Clamping Force: 150 Ton - Heating Platens Dimensions: 430x50 ...

- Please note! Price per piece! - Suitable for several motors - LS-4000 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting and integrating new technologies and processes int ...

Used injection molding machine, Manufacturer of Husky Injection Systems Ltd. Type: GL225RS60/50 Year of constr.: 23.04.1998 400 V, 96 A greatest engine, 42 A total load heating Functional The machine can be visited like us. Price: 8.000,00 plus VAT, from stock Sale even after parts possible

Used injection molding machine with Siemens controller, Manufacturer of Husky Data plate: Load supply no. 1 400V 207 A, 50 Hz, 3 p + N + PE system Biggest motor 110 A Total load heating 90 A Short circuit intermittent performance 35 kA Load supply Nr 2 Type of machine: LX225 RS60/50 Relay individually on request. The machine can be visited like after consultation with us.

Description Item # 9231 - CROISSANT/ CAKE INJECTION FILLING MACHINE Manufactured by GORRERI Model SVG800 - 800mm working width For fillings such as: creams, jams, fruit jelly Two sets of needles : for big croissants/cakes: for mini croissants/cakes Year 2007 (used in production for 2 1/2 years and then held as a back-up machine) Production capacity: 20 cycles/min Weight: 750 kg Power: 7.5 kW Feeding tension: 380 V (3Ph+T+N) Auxiliary tension: 24 V DC Frequency: 50 Hz Working pressure: 6 bar

New injection pump 0402 066 725(=PES6P110A120RS3336-1) NET 2.950,-EURO 6 x new injectors 0432 191 342 (Cummins # 408931500) net / piece 215,-EURO Mail: info@miw-zeven

APV COMBI UHT TREATMENT STERILIZATION PASTEURIZATION PLANT – 2006 Includes both TUBULAR and INJECTION systems. Capacity 4.000 - 8.000 Lt /h DISASSEMBLED AND READY FOR LOADING - APV PLATE HEAT EXCHANGER for cooling - APV TUBULAR ( INDIRECT ) UHT Treatment system. - APV INJECTION ( DIRECT STEAM ) UHT Treatment system. - APV ASEPTIC HOMOGENIZER 250 BAR - OPTIONAL - APV CIP CLEANING UNIT - APV VALVE CLUSTER FOR ASEPTIC TANK - (TANK IS EXCLUDED) - ELECTRIC CONTROL PANELS Fast heating (~300°C/sec) for optimal taste and minimal degradation Instantaneous flash cooling for flavor and aroma preservation Uniform heating via indirect tubular exchangers for gentle thermal treatment High energy recovery (up to 90%) to reduce utility consumption and cost. Precise thermal control with uniform product treatment Efficient spore kill with very low C ...

complete screw and barrel dia. 45 mm for Battenfeld /1000 injection moulding machine is good condition

Consists of: ROLLER/EX rubber pressure rollers / packer rollers Consisting of: 2 rubber rollers Working width: approx. 2,200 mm per roll Roller diameter: approx. 500 mm 18 rubber rings per roll Total: 36 rubber rings Steel frame, red Including mounting material The rollers and frame have been disassembled. As far as is known, all parts and fasteners are present to rebuild the whole. Auction-ID: A1-47386-273

Make: Engel Type: Vertical Rubber Injection Model: ES 280V/40VT-ELAST Serial number: 41938, Year of manufacture: 2000 Clamping force 400kN Injection volume 280cm3 Platen size: 860x400mm In good condition.

REP H48Y10W Horizontal Injection Moulding Machine Year of construction 2005 Machine Parameters Volume [cm3] 1000 Clamping force [kN] 1930 Injection pressure [bar] 1500 Moulds dimension [mm] 450x450 Tonnage 1.9t Platen size: 450x450 Cycles: 2,220,383 General condition: operational Dims [mm]: 4200 L x 1400 W x 2200 H Weight [kg]: 6750

clamping force: 1.300 kN injection volume: 230 cm³ screw diameter: 45 mm platen size: 685 x 685 mm Condition: used, Specification: injection moulding machine for TPE - used including Koch dosing unit clamping unit: - clamping force: 1.300 kN - heating platen size: 685 x 685 mm - Clear distance between tie bars: 470 x 470 mm - Mould installation height min.: 250 mm - Distance between platens max.: 900 mm - Opening stroke max.: 650 mm - Ejector stroke: 225 mm Injection unit: - Screw diameter: 45 mm x 18D - Injection volume max.: 230 cm³ - Injection part weight: 210 g/hp - Max. injection pressure: 1,670 bar - Screw circumferential speed: 75 m/min - Cylinder heating: 4x 2,200 W - Nozzle heating: 600 W - Connection value: 3x 400 V, 50 Hz - Electrical connection (back-up fuse): 100 A - Weight approx.: 6,3 ...

clamping force: 350 kN injection volume: 59 cm³ screw diameter: 25 mm platen size: 400 x 400 mm Condition: used, Specification: injection moulding machine for rubber - used International size: 350-90 clamping unit: - clamping force: 350 kN - clamping platen size: 400 x 400 mm - Clear distance between tie bars: 270 x 270 mm - Mould installation height min.: 225 mm - Distance between clamping platens: max. 550 mm - Opening stroke max.: 325 mm - Ejector stroke: 125 mm Injection unit: - Screw diameter: 25 mm x 20D - Injection volume max.: 49 cm³ - Injection part weight: 59 g/hp - Max. injection pressure: 1,860 bar - Screw circumferential speed: 37 m/min - Cylinder heating: 4x 900 W - Nozzle heating: 300 W - Heating complete: 4,6 kW - Pump motor: 11 kW - Total power ...

Maplan Injection Moulding Machine Model: MTF400/80C 80 Ton Safety distance 162mm Run-on time 81ms Follow-up 5mm Pattern size 510mm x 410mm Touch screen control Year 2010

LWB Steinl Injection Moulding / Vulcanizing Press Model: VCE-B Clamping force 2500kN Injection volume 1000 cm3 Compressed air 6 bar 75 kW Hydraulic oil 40/45 cst Pattern size 760 x 630mm LWB Flex touch screen Qty 1 Tool Kemp model TT-188 (year 2019) hot runner. Weight 12850 kgs

LWB Steinl Injection Moulding / Vulcanizing Presses Models available: VCEFE-B and VCEFE Clamping force 2500kN Injection volume 1000 cm3 Compressed air 6 bar 76 kW Hydraulic oil 46/40 cst Pattern size 760 x 630mm LWB Flex touch screen Qty 2 Tool Kemp model TT-188 Weight 13500 kgs

LWB Steinl Injection Moulding / Vulcanizing Press Model: VCEFE Clamping force 2500kN Injection volume 1000 cm3 Compressed air 6 bar 76 kW Hydraulic oil 46/40 cst Pattern size 760 x 630mm LWB Flex touch screen Qty 2 Tool Kemp model TT-188 Year 2013 Weight 13500 kgs

LWB Steinl Injection Machine Type VCE -T 500/160 T Clamp power 500 KN Injection volume 160 cm3 Year 2006 6 Bar 400 v 50 hz 26 KW

clamping force: 400 kN injection volume: 125 cm³ screw diameter: -- mm platen size: 300 x 300 mm Condition: used, Specification: C-frame injection moulding machine for TPV - second-hand clamping unit: - Clamping unit: vertical - Tonnage: 40 t - clamping force: 400 kN - Heating platen size: 300 x 300 mm Injection unit: - Injection volume max.: 125 cm³ - Connected load: 3x 400 V, 50 Hz 76A fuse protection (incl. peripherals) - Pump output: 7.5 kW, 14.9 A - Total output: 28 kW Dimensions L/W/H approx.: 2,000 x 1,500 x 2,500 mm Weight approx.: 2,250 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 200 kN injection volume: 80 cm³ screw diameter: -- mm platen size: 350 x 300 mm Condition: used, Specification: C-frame injection moulding machine for TPV - second-hand clamping unit: - Clamping unit: vertical - Tonnage: 20 t - clamping force: 200 kN - Heating platen size: 350 x 300 mm Injection unit: - Injection volume max.: 80 cm³ - Connected load: 3x 400 V, 50 Hz - Pump output: 11 kW - Total output: 44 kW Dimensions L/W/H approx.: 2,000 x 1,500 x 2,500 mm Space requirement approx: 5 m² Weight approx.: 3.200 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

REP Press Model V58Y10W Injection volume 1000ccm Platen size: 500 x 630 mm Year 2006 Power: 2550 kN Operating hours: 14570 Moveable traverse Fix traverse Sliding Table

clamping force: 400 kN injection volume: 125 cm³ screw diameter: -- mm platen size: 600 x 400 mm Condition: used, Specification: C-frame injection moulding machine for TPV - second-hand clamping unit: - Clamping unit: vertical - Tonnage: 40 t - clamping force: 400 kN - Heating platen size: 600 x 400 mm Injection unit: - Injection volume max.: 125 cm³ - Connected load: 3x 400 V, 50 Hz 90A fuse protection Approx. dimensions: 1,550 x 1,050 x 3,120 mm Weight approx.: 2,250 kg Two identical systems are available. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 400 kN injection volume: 125 cm³ screw diameter: -- mm platen size: 550 x 400 mm Condition: used, Specification: C-frame injection moulding machine for TPV - second-hand, Modell TTV-C40-125 C40P01B clamping unit: - Clamping unit: vertical - Tonnage: 40 t - clamping force: 400 kN - Heating platen size: 550 x 400 mm Injection unit: - Injection volume max.: 125 cm³ - Connected load: 3x 400 V, 50 Hz 90A fuse protection Approx. dimensions: 1,550 x 1,050 x 3,120 mm Weight approx.: 3,200 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 350 kN injection volume: 58,5 cm³ screw diameter: 28 mm platen size: 260 x 254 mm Condition: used, Specification: injection moulding machine for TPE - used clamping unit: - clamping unit: vertical - clamping force: 350 kN - opening stroke max.: 300 mm - platen distance max.: 500 mm - Mould installation height min.: 200 mm - Clear width between tie bars: 260 x 254 mm - Ejector stroke max.: 80 mm - Clamping unit: VV - Lift of protective bonnet: 500 mm Injection unit: - Screw diameter: 28 mm - Screw L/D ratio: 18.6 - Screw stroke max.: 95 mm - Injection volume max.: 58.5 cm³ - Injection pressure: 1577 bar - Plasticising flow: 8.6 g/s - Injection flow: 85.5 g/s - Connected load: 3x 400 V, 50 Hz - Max. heating power: 5.8 kW - Drive power: 7,4 kW - Total power: 13,2 kW - Hydraulics: 210 bar (tank 65 litr ...

clamping force: 4.000 kN injection volume: 2.700 cm³ screw diameter: -- mm platen size: -- mm Condition: used, Specification: Rubber Injection Molding Machine - second-hand clamping unit: - Clamping force: 4000 kN - ejection device: 2-layer - Brush system: 2-layer Injection unit: - Injection volume max.: 2,700 cm³ Two identical systems are available. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Maplan 250ton Injection Machine Injection MTF 1500/250 Platen size = 630mm x500mm Stripper plate/ejectors =top only Max gap between platens = 702mm Volume = 1500 ccm3 Tonnage = 250T Year 2007

Maplan 160ton Injection Machine Injection MTF 750/160 Platen size = 510mm x 450mm Stripper plate/ejectors =top only Max gap between platens = 575mm Volume = 750 ccm3 Tonnage = 160T Year 2002

clamping force: 500 kN injection volume: 76,5 cm³ screw diameter: 32 mm platen size: 360 x 335 mm Condition: used, as good as new Specification: Injection moulding machine for LSR - Demonstration machine as good as new clamping unit: - clamping unit: horizontal - Clamping force: 500 kN - Opening stroke max.: 400 mm - Platen distance max.: 650 mm - Mould installation height min.: 250 mm - Clear width between the tie bars: 360 x 335 mm - Ejector stroke max.: 80 mm Injection unit SP 82: - Screw diameter: 32 mm - Screw L/D ratio: 16.3 - Screw stroke max.: 95 mm - Injection volume max.: 76.5 cm³ - Injection pressure: 1076 bar - Plasticising flow: 13 g/s - Injection flow: 204.8 g/s - Connected load: 3x 400 V, 50 Hz - Max. heating power: 5.8 kW - Drive pow ...

Engel Injection Machine Type ES 1500T/160 V – ELAST Stroke slide plate 300mm Stroke central ejector for slide plate 100mm Force central ejector for slide plate 30kN Stroke lateral mechanical ejector 250mm Stroke lateral hydraulic ejector 250mm Force lateral hydraulic ejector 80kN Stroke central ejector 120mm Force central ejector 20kN Pump drive power 15kW Oil filling 1 225 Operating pressure of hydraulic system 250bar Capacity temperature control unit 2x3 kW Total connected load 48kW Dims: 2675mm long x 1350mm wide x 3310mm high Weight: 6900 With instruction manual

Rep M46 Injection Moulding Machine Size of platens 430x430mm Injection unit short volume 670cm3 Injection pressure 1690 bar Injection force 331kN

Rutil Vertial Injection Moulding Machine Year of manufacture: 2001 Type: Injection Configuration: Vertical Clamping force: 350 tons Injection volume: 2000 cc Upper intermediate frame: Yes Lower intermediate frame: Yes Heater plate dimensions: 600×650 mm Tie bar distance: 600 / 340 mm Additional heating option: Yes Sliding plate: Yes

Year of construction : 2011 Control CC200 Locking force 400 tons incl. various accessories ( Piovan cooling unit, Tooltemp cooling unit, vacuum pump ) Machine comes directly from production

An injection molding machine Maplan for elastomers requiring repair is available. Design: hydraulic vertical press, hydraulic oil type: ISO VH 46 HLP, hydraulic oil filling quantity: approx. 600l, max. hydraulic pressure: 250bar, heating cartridge diameter: 25mm, insulation plate thickness: 14mm, max. operating temperature: 250°C, L/D ratio: 12:1, max. back pressure: 400bar, max. stroke: 260mm, vacuum pump capacity: 63m³/h, weight: approx. 17500kg, control system: B&R PLC. The temperature control units and the hydraulic clamping system have failed. Documentation available. An on-site inspection is possible.

clamping force: 250 kN injection volume: 134 cm³ screw diameter: 35 mm platen size: 300 x 300 mm Condition: second-hand, Specification: C-frame injection moulding machine - second-hand Clamping unit: - Clamping force: 250 kN - Heating plate dimensions: 300 x 300 mm - Heating power of the plates: 5.3 kW - Clamping/opening stroke: 330 mm - Platen distance with heating plates at maximum: 380 mm - Clamping direction: from below - Side ejector: yes - Stroke of side hydraulic ejector: 100 mm - Ejector stroke/force: 70 mm / 24 kN Injection unit: - Increased injection pressure: 1,580 bar - Maximum injection volume: 134 cm³ - Screw diameter: 35 mm - Screw length: 17.1D - Maximum screw speed: 20–480 rpm - Metering stroke: 140 mm - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE Pump drive power:  ...

clamping force: 250 kN injection volume: 134 cm³ screw diameter: 35 mm platen size: 300 x 300 mm Condition: second-hand, Specification: C-frame injection moulding machine - second-hand Clamping unit: - Clamping force: 250 kN - Heating plate dimensions: 300 x 300 mm - Heating power of the plates: 5.3 kW - Clamping/opening stroke: 330 mm - Platen distance with heating plates at maximum: 380 mm - Clamping direction: from below - Side ejector: yes - Stroke of side hydraulic ejector: 100 mm - Ejector stroke/force: 70 mm / 24 kN Injection unit: - Increased injection pressure: 1,580 bar - Maximum injection volume: 134 cm³ - Screw diameter: 35 mm - Screw length: 17.1D - Maximum screw speed: 20–480 rpm - Metering stroke: 140 mm - Injection: from above - Voltage: 3x 400 V, 50 Hz, N, PE Pump drive power:  ...

clamping force: -- kN injection volume: -- cm³ screw diameter: -- mm platen size: -- mm Condition: second-hand, Specification: C-frame injection moulding machine - second-hand, used as a spare parts source for cannibalising 3x machines, model SAD 114/30 - Year of manufacture: 1999 - Problems with the control system 1x machine, model Super AD 76/15 - Year of manufacture: 2006 - Problems with the control system There are 3 machines built in 1999 and 1 machine built in 2006 available. The price is per unit. If you purchase several units a package price can be arranged. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 120 kN

Mohrtek injection press, vertical loadable, horizontal pressing machine. please contact for more information

clamping force: 350 kN injection volume: 170 cm³ screw diameter: 36 mm platen size: 380 x 300 mm Condition: second-hand, Specification: C-frame injection moulding machine - second-hand Clamping unit: - Clamping force: 350 kN - Platen size: 380 x 300 mm - Heating power of the plates: 6 kW - Clamping/opening stroke: 200 mm - Clearance between the plates: 250 mm - Clamping direction: from below Injection unit: - Pressure: 1,050 kg/cm² - Maximum injection volume: 134 cm³ - Screw diameter: 35 mm - Max. screw speed: 30–110 rpm - Metering stroke: 165 mm - Injection: from above - Voltage: 3 × 400 V, 50 Hz, N, PE - Pump drive power: 11 kW - Hydraulic motor power: 10 kW - Dimensions LxWxH: 2,400 x 1,200 x 3,300 mm - Weight approx.: 3,000 kg The data for this ad was created with ModulMWS - the  ...

Desma Vertical Injection Moulding Machines Model Type D968 250 ZO ( S3 ) Stroke Volume 2000 cm3 Injection Pressure 1670 bar Platen 560 mm x 630 mm Extended Daylight 860 mm Top and Bottom Hydraulic ejectors 400 mm stroke Strip Intake Control With Vacuum Pump Years: 2014 / 2015

clamping force: 300 kN injection volume: 180 cm³ screw diameter: -- mm platen size: 300 x 300 mm Condition: second-hand, Specification: C-frame injection moulding machine for rubber - second-hand Clamping unit: - Clamping unit: vertical - Clamping force: 300 kN - Platen size: 300 x 300 mm Injection unit: - Maximum injection volume: 180 cm³ - Mains supply: 3x 400 V, 50 Hz - Power rating: 11 kW - Control system: MAPLAN The machine is still in production and can be viewed in operation. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 4.500 kN injection volume: 5.000 cm³ screw diameter: -- mm platen size: 670 x 780 mm Condition: second-hand, Specification: rubber injection moulding machine - second-hand EUROMAP size 4500 – 10000 Clamping unit: - Clamping unit: vertical - Clamping force: 4500 kN - Platen size: 670 x 780 mm - Max. stroke: 600 mm (see data sheet) Injection unit: - Max. injection volume: 5,000 cm³ - Injection pressure: 2060 bar - Power supply: 3x 400 V, 50 Hz, N, PE - Motor power: 38 kW - Installed heating capacity: 67.5 kW - Weight: Clamping unit approx.: 8,900 kg Injection unit approx.: 3,200 kg Hydraulic unit with oil and control cabinet 2,350 kg - For dimensions, see the installation data in the appendix There are 6 machines available, manufactured between 2001 and 2004. The data ...

clamping force: 2.700 kN injection volume: 6.000 cm³ screw diameter: -- mm platen size: 560 x 630 mm Condition: second-hand, Specification: rubber injection moulding machine - second-hand, partially dismantled, but would be restored to its previous condition EUROMAP size 2500 – 7000 Clamping unit: - Clamping unit: vertical - Clamping force: 2.700 kN - Platen size: 560 x 630 mm - Max. stroke: 550 mm (see data sheet) Injection unit: - Max. injection volume: 6,000 cm³ - Injection pressure: 2150 bar - Power supply: 3x 400 V, 50 Hz, N, PE - Motor power: 28,2 kW - Installed heating capacity: 49,9 kW - Weight: Clamping unit approx.: 6,040 kg Injection unit approx.: 2,700 kg Hydraulic unit with oil and control cabinet 1,860 kg Total weight approx.: 10.600 kg - For dime ...

clamping force: 4.500 kN injection volume: 3.300 cm³ screw diameter: -- mm platen size: 670 x 780 mm Condition: second-hand, Specification: rubber injection moulding machine - second-hand EUROMAP size 4000 – 7000 Clamping unit: - Clamping unit: vertical - Clamping force: 4500 kN - Platen size: 670 x 780 mm - Max. stroke: 600 mm (see data sheet) Injection unit: - Max. injection volume: 3,300 cm³ - Injection pressure: 2150 bar - Power supply: 3x 400 V, 50 Hz, N - Motor power: 35,5 kW - Installed heating capacity: 73,9 kW - Weight: Clamping unit approx.: 8,400 kg Injection unit approx.: 2,700 kg Hydraulic unit with oil and control cabinet 2,200 kg Additional equipment (approx.): 3,000 kg Total weight approx.: 16.300 kg - For dimensions, see the installation data in the appe ...

clamping force: 4.500 kN injection volume: 5.600 cm³ screw diameter: 610 - 985 mm platen size: 670 x 780 mm Condition: second-hand, Specification: rubber injection moulding machine - second-hand EUROMAP size 4500 – 12300 Clamping unit: - Clamping unit: vertical - Clamping force: 4500 kN - Platen size: 670 x 780 mm - Max. stroke: 610 - 985 mm (see data sheet) Injection unit: - Injection unit type: ADV - Max. injection volume: 5,600 cm³ - Injection pressure: 2200 bar - Power supply: 3x 400 V, 50 Hz, N, PE - Pump capacity: 27 kW - Weight: Cutting unit approx.: 10,200 kg Injection unit approx.: 3,500 kg Hydraulic unit with oil: 2,600 kg Accessories approx.: 4,700 kg Total weight approx.: 21,000 kg - For dimensions, see the installation data in the appendix The data for this ad w ...

A Klöckner DESMA rubber injection molding machine with increased clamping pressure is offered. Material processing: rubber, clamping force: 4500kN, min./max. mold height: 180mm/530mm, adjustable opening stroke: 570mm, clear distance between tie bars X/Y: 600mm/810mm, max. clamping area X/Y: 670mm/940mm, heating platen size X/Y: 670mm/940mm, injection: from above, max. injection volume: 3300cm³, injection force: 1886kN, max. injection pressure: 2150bar, screw diameter: 55mm, injection plunger diameter: 105mm, operating pressure: 250bar, number of control zones: 12, heating capacity per control zone: 21kW, ejector: hydraulic top and bottom, ejector slot spacing: 730mm. The machine is currently not operational because the control cabinet of the DRC 2000 (Simatic S7) is already being used elsewhere and is not part of the machine. Documentation available. Inspection possible by arrangement.

Key data: 2700 kN, 29 g/PS

We offer this DESMA D 969.250 Z (S3) rubber processing machine in mint condition, built in 2021. Clamping force: 2700 kN Injection volume: 500 cm³ Injection pressure: 3500 bar EUROMAP size: 2700-1750 Voltage: 400 V Frequency: 50 Hz Short circuit current max.: 10 kA Total current: 138 A Pre-fuse: 160 A Pump pressure: 265 bar Pump drive capacity: 72/39 l/min Pump drive current consumption: 32.0 A Pump drive power: 22 kW Nozzle application force: 58 kN Weight: 10.7 t Compressed air volume flow: 0.5 m³/h Compressed air pressure: 6 bar Cooling water volume flow: 1.6 m³/h Cooling water temperature max.: 20 °C Hydraulic motor hours: 730 hours, Hydraulic pump (clamping force): 65 Hours, Operating System: active 3,360 hours Ideal for the production of: - Technical moulded rubber parts - Seals and O-rings - Automotive and industrial components Condition & Avai ...

1 x Francis Shaw 45mm dia coldfeed rubber extruder, M/c no. 4513, Year: 1992, power roll feed, L/D ratio 15:1, hinged straight head with c\clamp, cored scred + jacketed barrel with built in temp control unit. Complete with control panel and in very good condition. Box of dies included.