rotation used for sale

CHARACTERISTICS STRETCH-STRAIGHTENING   force: 500 kN   Working length: 13000 mm   center height: 250 mm   stroke: 1000 mm max. stretching length: 13'000 mm max. stretching length:  3'000 mm jaw width: 160 mm jaw opening: 0-100 mm Torque: 600 Nm Rotation angle: +/- 90 degrees Rotation speed standard: 1 rpm Rotation speed fine: 0.25 rpm Stretching speed: 10.8 mm/sec Rapid speed in working direction: 106 mm/sec Rapid speed in return for releasing: 93 mm/sec Toothed rack pitch: 250 mm Jaw confirmation: 5-6 kgf/cm2 (pneumatic) Mandrel confirmation: 5-6 kgf/cm2 (pneumatic)

Manufacturer PWH Flow capacity 400 m3 hour of bulk material Grit 0 to 30 mm Bulk weight 0.84 to 0.90 to / m3 Water content 18% Heap height 12 meters Operating voltage 380 V Control voltage 220 V Bucket capacity: 100 litres • Number of shovels: 8 pieces • Bulk per minute: 60 • Theoretical power: 360 m3/h • Effective power: 280 m3/h • Bucket wheel diameter: 3.45 m • Circumferential force (wheel): 15,000 N • Cutting speed on the knife: 1.35 m/sec • Removal height (heap height): 12 m • Discharge of the lowered wheel: 11 m • Lifting height on the paddle wheel: 6 m • Lifting speed on the paddle wheel: approx. 3 m/min • Senovice speed on the paddle wheel: approx. 3m/min • Swivel speed: approx. 12 m/min • Angle of rotation of the trolley (suspension): 360 • Angle of rotation of the trolley

Container filling system Turret with horizontal Rotary and longitudinal moving conveyor on sturdy galvanized frame, swivel bearings. Incl. support climbing belt and tied up to the automatic filling of three large containers. PLC control Distribution belt gear motor 2 .2kW / conveyor width 900 mm Achabstand 5500 mm Drive rotation 0, 6kW Rotation drive +/-90 ° Climbing belt conveyor width 600 mm / distance 4000 mm / drive 1, 1kW High belt conveyors conveyor width 600 mm / distance 4700 mm / drive 1, 1kW Colour RAL 9006 / White aluminium System now available Price and further details on request

Technical data: hydraulic undertable circular saw unit - drive power motor 7.5 kW- diameter saw blade Z=48x5 600 mm- diameter saw blade bore 30 mm- inclined working table Yes- Automatic rotation of the table -70C 0C+70C- Speed of rotation from / to 0C / 70 C 3s- Positioning accuracy +/- 0.2C- Pneumatic workpiece holder 2 pieces- Pneumatic side organizers 2 pieces- Safety cover via capping unit Yes- Cutting capacity at 0C: 160 x 310 mm, 80 x 390 mm- cutting capacity at 45C: 160 x 220 mm, 80 x 270 mm cutting capacity at 70C: 160 x 90 mm, 80 x 130 mm- minimum workpiece thickness 10 mm connection values - supply voltage 400 V / 50 Hz- Control voltage 24 V compressed air requirement at 8 bar per cycle approx. 8 Nl- Suction nozzle FI100 mm 2 pieces- Suction nozzle FI160 mm 1 piece- air speed Suction in center of nozzle approx. 25-35 m/s Electronically controlled slider:- Loading length: 6000 m ...

AUTOMATIC COPY SHAPER machine type BALESTRINI CP 4 second hand machine Technical Details : machine composed by 4 units : 2+2 shaper units max. working useful length mm.2500 max. working width mm. 500 max. working heigth mm. 180 speed rotation shaper units 8500 rpm speed rotation sanding units 3500 rpm hydraulic pump motor power Hp 5,5 net weigth kgs. 3300 Volt. 380/50

3 stueck unused electric motors for Saeege machines from Rueetschi 380 / 400 Volt 50Hz Dreick circuit 5.5 KW 11.3 A 2850 rpm With tool holder (saege leaf holder) Shaft diameter 30mm Diameter handle for saege leaf (middle) approx.55mm Diameter tool holder outside approx.165mm Total length motor approx. 570mm Total width approx. 200mm Price per piece Hole distance for screwing on the motor laengs 200mm Hole spacing Cross 200mm The abstinfers can be varied in the length and width, because the motor is screwed on to the console via T-slots. The T-slots are located on the motor. Thus, any hole distance would be feasible via a different console. Thread on the motor shaft is right thread (if the nut is in the clockwise, is tightened when the motor is counterclockwise and the mother is hooked- view from the front to the wave) Diameter of the thread approx. 28-30mm. direc ...

Heavy Duty Lathe SKODA Model: SR 200 Year of manufacture: 1975 Modernization in 2008 Technical details: Swing over bed: 2300 mm Swing over carriage: 1900 mm Max turning height: 8000mm Workpiece clamping target (chuck 4 jaws): 2000 mm Bed-3 guides Bed width: 2190mm Max workpiece weight: 60 000 kg Spindle rotation range: 0.45-90 rpm Toolpost rotation range: ± 90 ° Lathe feeds: 0.18-5.6 Main motor: 60 kW Lathe weight: app. 47 000 kg Machine dimensions: L = 14.5 m, B = 3, 60 m, H = 2, gutter, Equipment: clamping chuck-4 jaws with diameter of 2000 mm steady rest-1 pc self-centring steady rest-1 pc, Renovation in 2008: -final drive renovation -electric instalation exchange -new electrical cabinet -lubrication installation exchange -machine bed grinding -heightened from turing over the bed and over carriage-of 300 mm

Private sale Item condition: maintained Availability: immediately Coating band: yes ChocoTemper is part of the product line of the ICB Tecnologie chocolate temperature control device, with a tub capacity of 24 kg. Both machines can be equipped with vibrating table, while the coat straps for Chocotemper 24 are available • Stable stainless steel frame • Two independent motors, one for the screw and one for the agitator, for a longer life • Standard, removeable screw for easy cleaning and a quick change of chocolate • Control of the chocolate flow with pedal possible • Touchscreen control panel with various options: - Automatic dosages for a good way to do the right chocolate. - Night mode to keep the chocolate dissolved and reduce consumption during downtimes. - Counter-rotation of the screw, which is useful during cleaning The Chocotemper 24 chocolate temperature contro ...

Wörner series drilling machine 4 units in circular arc alignment Built in 1958 MK2 spindle - speed change by Keilreinemscheibenwechsel Shaped casting table - drilling units height adjustable max wide table/spindle: approx. 500 mm - and rotatable with clamp. Drilling units throat depth: 280 mm Coolant system on each drilling unit; 1 x Unit TIBO 13 with Albrecht Chuck 0-13 mm left/right rotation Stroke: 0-100 mm with drill depth - fine adjustment screw Rpm: 560-3500 RPM motor 0.55 kw 50 Hz 380V 3 x units UNIVA 16 MK 2 recording left/right rotation speed: 540-3600 RPM (gear reduction speed unit is missing) Engine power: 0.55 kw 50 Hz 380V -of which a unit of UNIVA with automatic speed switching for tapping saturation (return 1.5 fold) speed: 350-2300 RPM (gear reduction speed unit is missing) Engine power: 0.4/0,35 kw 50 Hz 380 v 900/14540 U/min Stroke: 0-100 mm wit ...

spindle moulder with tilting shaft SAC SUERI TS 145 second hand machine electric shaft inclination -5 ° / + 45 ° electric mast lifting extended plans support extension motor power Hp 7,5 n.5 shaft rotation speed electrical inversion of the direction of rotation shaft diameter mm. 35 volt. 380/50

Number of vertical independent spindles: 9 Number of horizontal spindles on axis X : (2+2) Number of horizontal spindle on axis Y: (1+1) N° 1 saw blade unit: (ø 100 mm) Router head 3,6 Kw ISO 30 - 12000/24000 rpm Max. thickness of the panel: 50 mm Control: Full Parametric Max weight of the panel: Kg 25 Max panel size: X ,Y 1100, Z 50 mm Min panel size: X 270,Y 150 (70 op.), Z 12mm Number of controlled axes: 3 Panel feeding speed: 25m/min Spindles speed rotation: 3600 rpm Saw blade speed rotation: 7000 rpm Air pressure: 7 bar Diameter of the dust extraction: ø 140 mm Exhaust air consuntion: (2000 mc/ora) - (30 m/s) Max drilling depth in horiz. on X and Y axis: 30 mm Max drilling depth in vertical: 45 mm Max horizontal diameter of the tools: 12 mm Max vertical diameter of the tools: 35 mm Motor power: 1,5 kw Max air consumption: 60 Nlt./min. Total power : 6,4 Kw  ...

Technical data: -Lifting capacity 2000 kg -max load capacity horiz. 3500 kp -Faceplate hub 1750 x 1750 mm -Drehkreuzverängerungen -Faceplate geared motor Tiltable 0-90 ° -Rotation Electr. adjustable 0.2-1.5 m / min -Right - left rotation - welding current transmission 1200 A -400 V - table height in horiz drive. Position with frame approx. 2070 mm -Table height at horiz. Position without stand approx. 940 mm -Space requirement approx. B 1650 x H 1130 / 940 x H 2500 mm -Weight approx. 2.2 t

Technical data: -max load capacity 3000 kg -Faceplate cross 1600 x 1600 mm -Faceplate cross extension tubes - faceplate cross mot. adjustable 0-90 / 135 ° - rotation infinitely variable 0,01-4 U/min -Right - + rotation control -Transmission of welding current approx. 500 A -400 V - table height in horiz drive. Position without stand approx. 1200 mm -Table height at horiz. Position with frame approx. 2200 mm -Space requirement approx. B H 1600 x 1200 + 1000 X 2400 mm -Weight approx. 2700 kg

Deburring machine make RSA type Turnamat 2Machine -No: 48-1047 / 96 built in 1996Technical specifications:Workpiece cross-sections: 10 x 10 to 150 x 150 mm2 brush speeds: 1500/3000 rpm.Deburring time: 1 - 5 sec.Drive power: 3.5 / 4.6 kWsuitable for- Steel, VA, aluminum, copper and brass- Deburring by rotating the brush at high speed- Service rotation = circling the brush around the axis of rotation, i.e. continuous change of working direction at low speedused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Deburring machine make RSA type Turnamat 2Machine -No: 048-028908 built in 2008Technical specifications:Workpiece cross-sections: 10 x 10 to 150 x 150 mm2 brush speeds: 1500/3000 rpm.Deburring time: 1 - 5 sec.Drive power: 3.5 / 4.6 kWDimensions approx .: 1200 x 1200 x 1800 mmWeight about: 550 kgsuitable for- Steel, VA, aluminum, copper and brass- Deburring by rotating the brush at high speed- Service rotation = circling the brush around the axis of rotation,i.e. continuous change of working direction at low speedused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

K-280 sharpener is a device thanks to which you can professionally sharpen various types of grinder knives and plates in your plant. The sharpener is fully automated. The built-in programmer allows the user to program parameters such as time, thickness of cut and tempo. The device has a magnetic holder built-in. The machine perfect for meat processing plants and the meat industry. Specification: Producer: BMG TRADE Model: K280 Dimensions: 1150 x 570 x 625 (mm) Power supply: 400V 50Hz Total motor power: 2.67 kW Cooling pump power: 0.12 kW Rotation: 2860 rpm Tank capacity: 33 L Thickness of cut: 0.2mm; 0.4mm; 0.8mm; 1.2cm; 1.6cm; 2,00cm Program of grinding pace Rotation: Right / left Weight: 250 kg

Stock# U2301-1 Second hand stainless steel contact parts twin shaft planetary dissolver by Molteni type TM5 RP.SV. Mixer has stainless steel jacketed mixing pan with internal diameter 207 mm x depth 213 mm. Total volume of pan is 7 l, working volume about 5 l. Mixing pan has side wall bottom discharge outlet. Mixer has two agitators with toothed discs and one wall scrapper. Toothed discs have diameter 100 mm and are driven by vari speed gearbox and two speed el. motor 1.75/1.4 kW, 2800/1400 rpm, 380 V, 50 hz, in EEx-d II B T4. Working rotation of disc agitators manually adjustable in range from 300 up to 4800 rpm. Wall scrapper is driven by el motor 0.26 kW, 1360 rpm, 220/380 V, 50 hz (design EEx-d II B T5) through reducer with ratio i= 44.77, what gives output rotation at 32 rpm. Agitators are risen by hydraulical device driven by el. motor 0.26 kW, 1360 rpm, 220/380 V, 50 hz, EEx-d II ...

Retrofitted in 1998 and revised in 2012 by SIRMU Technical datas: Stroke: 2000 mm Inclination of the platform: 0-60 ° Rotation: 360° Table diameter: 4.500 mm Maximum table load: 50,000 kg Plate diameter: 2.250 mm Movement 4 stages 1 28 mm / min 2 100 mm / min 3 280 mm / min 4 560 mm / min tilting of the table: 0-60 ° 4 stages 2 0.7 ° / min 3 2 ° / min 4 4 ° / min 5 7 ° / min Rotation of the table 4 stages 1 270 mm / min referring to a diameter of 3,500 mm 2 890 mm / min 3 2,700 mm / min 4 5,400 mm / min Total weight: 90,000 kg

Technical data: CNC Heidenhain 530 TABLE: Table dimensions: mm 1.600 x 1.250 Table rotation: continuous Capacity: kg 6.000 WORKING CAPACITY: Longitudinal travel/X-axis: mm 3.000 Transverse stroke/Y axis: mm 1.250 Vertical travel/Z axis: mm 1.600 Luge stroke/W axis: mm 650 MANDREL: Spindle connection: ISO 50 Barrel diameter: mm 130 Rotation speed: 2,000 rpm Motor power: kW 22 TOOL MAGAZINE: Tool stations: Nr. 60 GENERAL: Overall dimensions: mm 7.700 x 5.500 x 4.600 Machine weight: kg 33.000 Machine complete with: High pressure through the spindle Blowing air through the spindle Remote electronic handwheel Heidenhain optical lines Instruction manuals NB: The aforementioned technical data, collected from the technical data sheet of the manufacturer, are to be considered non-binding and subject to change without notice.

Used machine in good condition. Available for immediate delivery. - Number of turret stations (pcs): 0 - Material thickness steel Fe52/Fe37 max: 0 mm - Material thickness aluminium max: 0 mm - Axis speed [X axis] max: 0 m/min - Operating hours: 0 - Material thickness (punching) max: 0 mm - Material thickness max: 0 mm - Material thickness stainless steel max: 0 mm - Simultaneous positioning speed (X / Y): 0 m/min - Punching speed (Hit speed max.): 0 1/min - Number of index tool stations, max: 0 - Tool rotation, max: 0 r/min - Control type: 0 - Compressed air pressure min: 0 bar - Compressed air consumption max: 0 l/s - Turret rotation: 0 r/min - Oil tank capacity: 0 l - Power supply: 0 kVA - Axis speed [Y axis] max: 0 m/min - Working area max: 0 mm - Punching force: 0 kN - Punch diameter max: 0 mm - Max. workpiece weight: 0 kg - Power: installed max: 0 kW - D ...

Type 400C Surface planer: Table dimensions 400?1800 mm Cutterblock diameter 70 mm Cutterhead rotating speed 5700 rpm 3 knives 400x20x3 mm Max table adjustment 4 mm Thickness: Table dimensions 400x760 mm Max cutting depth 4 mm Feed speed 7 m/min Cutterblock rotation speed 5700 rpm Max working height 220 mm Min working height 4 mm Mortising: Table dimensions 250?500 mm Longitudinal stroke 205 mm Trasversal stroke 95 mm Chuck (SX) 16 mm Chuck rotation speed 5700 rpm Motor 3 kW Accessories: service wrenches, guards on mortise chuck, planer guide. Weight 390 kg

Type 300C Surface planer: Table dimensions 300?1500 mm Cutterblock diameter 70 mm Cutterhead rotating speed 5700 rpm 3 knives 300x20x3 mm Max table adjustment 4 mm Thickness: Table dimensions 300x660 mm Max cutting depth 4 mm Feed speed 7 m/min Cutterblock rotation speed 5700 rpm Max working height 220 mm Min working height 4 mm Mortising: Table dimensions 250?500 mm Longitudinal stroke 205 mm Trasversal stroke 95 mm Chuck (SX) 16 mm Chuck rotation speed 5700 rpm Motor 2,2 kW Accessories: service wrenches, guards on mortise chuck, planer guide. Weight 290 kg

MAX DIAMETER OF ROTATION: 750 MM MAX DIAMETER SWITCHABLE: 680 MM SWITCHABLE LENGTH: 1195 MM CNC: FANUC 18i-TB MAIN SPINDLE: MAX SPEED. OF ROTATION: 2800 RPM DIN 55026 8 ' ' CHUCK NOSE BAR PASS: 95 MM MOTOR POWER: 30 KW SELF-CENTRING DIAMETER: 315 MM Tailstock: POSITIONING STROKE: 1310 MM RACEWAY: 150 MM TUBE DIAMETER: 115 MM TORRETA TOOLHOLDER: MOTOR POWER: 10-17.5 KW TOOL DIMENSIONS: 25X25 MM BARENI DIA DIMENSIONS: 32-40 MM

YEAR: 1989 CNC: FANUC 0T TORNIBILE: 300 mm TURNBACK LENGTH: 300 mm MANDRINO: MANDRINO ATTACK: 6 ASA BARRA CAPACITY: 56 mm ROTATION SPEED: 3240 rpm POWER: 26 Kw AXIS C: 360 degrees I TORRETTA: PORTASSTATION STATIONS: 12 Nr. MOTORS: 6 Nr. MANDRINO: MANDRINO ATTACK: 6 ASA ROTATION SPEED: 3240 rpm. POWER: 26 Kw AXIS C: 360 degrees The TORRET: PORTASSTATION STATIONS: 12 Nr. RELATED: 6 nr

The new automatic version of the Horizon Brown 425 cutting line has been designed to reduce cutting times and facilitate the operator in machine adjustments. The machine is easily adaptable to customer requests for the wide range of accessories provided in its production. MAIN FEATURES OF THE MACHINE: - easy-to-program machines - blade diameter Ø 425 mm - maximum cutting capacity Ø 143 mm - rapid movements with brushless motors - blade rotation with controlled speed with inverter - electronic control of the cutting table rotation movement - power wagon position control with magnetic stripe - 1550 mm feed wagon stroke with the possibility of automatic repetition - CNC or IMS controlled cutting angle - hydraulic adjustment of the vertical jaw - hydraulic adjustment of the horizontal jaw - possibility of connection with PC to optimize the cycle

VISION WIDE VB-2016 5-AXIS CNC gantry milling machine was manufactured in 2013 in Taiwan. The machine performs precision machining of heavy workpieces in three or even five axes, once the automatic swivel head is mounted to the vertical spindle. The machine’s top-quality cast-iron structure is rigid and resistant to bending stress, thus perfectly dampening the vibrations and oscillations generated during machining. The VISION WIDE VTEC VB 2016 CNC gantry milling machine centre is equipped with safety guards fitted around the entire machine with sliding doors that open flush with the X-axis travel. Inside, there is a large work table with a length of 2000 mm and a width of 1300 mm, which is supported along the entire length of the longitudinal travel and guided by two sliding guideways, making it possible to machine heavy workpieces even when the table is unevenly loaded. Two scre ...

Robust, high-quality rotary device for cylindrical workpieces (boiler roller set) with polyurethane coated steel rollers, infinitely adjustable rotation speed, high frequency protected, right and left run, the largest load capacity of the two units together 10,000 kg, Workpiece diameter 200 mm to 3,000 mm, drive power 2 x 0.18 kW, drive rollers made of steel dia. 250 x 160 mm, rotation speed 80 – 1,200 mm/min, maximum temperature load capacity of the rollers up to 110° C, dimensions see illustrations, weight of the set (driven and non-driven unit together) approx. 270 kg

Robust, high-quality rotary device for cylindrical workpieces (boiler rollers), steel rollers coated with polyurethane, infinitely adjustable rotation speed, high frequency protected, right and left run, maximum load capacity of the two units together 14,000 kg, Workpiece diameter 600 mm to 5,500 mm, drive power 2 x 0.55 kW, steel drive rollers of 400 x 100 mm, rotation speed 120 – 1,200 mm/min, maximum temperature load capacity of the rollers up to 110° C, dimensions see illustrations, weight of the set (driven and non-driven unit approx. 870 kg

Robust, high-quality rotary device for cylindrical workpieces (boiler roller set), steel rollers coated with polyurethane, infinitely adjustable rotation speed, high frequency protected, right and left run Largest load capacity of the two units together 5,000 kg, workpiece diameter 200 mm to 3,000 mm, drive power 2 x 0.37 kW, drive rollers made of steel of 250 x 80 mm, rotation speed 80 – 1,200 mm/min, maximum temperature load capacity of the rollers up to 110° C, dimensions see figures, weight of the set (driven and non-driven unit together) approx. 230 kg

Stock# U2403-1 Used stainless steel homogenizing mixer by Brogtec (CH) model MH-8. Mixer has total volume of mixing chamber 10 l and working volume about 8 l. Tank is rising and lowering manually. Has bottom discharge outlet and possibility to discharge by manual tilt. Working pressure range - mixing chamber from vacuum till 29 PSI (2 bar). Heating jacket up to 43 PSI (3 bar). Working temperature range - mixing chamber from 32 - 250 F (-1 to 120 C). Heating jacket - from 89 - 250 F (31 - 120 C). Mixer is equipped with anchor with wall scrappers type agitator, vertical ribbon agitator and hi-speed homogenizing mill. Anchor and ribbon agitators are driven by gearbox and el motor 0.3/0.44 kW, 1660/3260 rpm, 460 V, 60 hz. Working rotation of vertical ribbon agitator is about 124 rpm, working rotation of anchor agitator - up to 62 rpm. Hi-speed homogenizing mill is belt driven by el motor  ...

The monoblock F87 is an automatic intermittent movement machine that can perform three operations at the same time: a volumetric filling and two closures. Aqueous, alcoholic, sugary, foamy, viscous products can be given. Droppers, glass or plastic pipettes, nebulizers, normal or freeze-drying rubber caps can be introduced. You can apply screw caps, press caps, ferrules, PFP etc. The carter and the machine table, on which all the operating groups are fixed from the inside, are in AISI 304 stainless steel and protect the mechanical parts from the infiltration of the treated products and the water used for washing. The operating units and their supports are made of AISI 304 stainless steel and receive their motion from a single variator motor, obtaining the dual purpose of relating, without interruption, the speed of the machine with the rotation speed of the screwing or seaming, and not to ...

Technical data of the used PAMA Speedram 2 boring machine: Spindle diameter: 150 mm Spindle taper: ISO 50 Milling spindle diameter: 254 mm RAM section: 360x400 mm Axes travels: Vertical travel (Y): 3200 mm Column travel (X): 10.200 mm Boring spindle travel (Z): 700 mm Axial stroke of the spindle tube (W): 800 mm Total axes travel (Z+W): 1500 mm Spindle speed: 1600 rpm Feeds rate: Working feeds: 1 + 6000 mm/min Rapid feed (X-Y-Z-W): 10.000 mm/min Power: Spindle motor: 65/40 kW Axis motors (X-Y): 65 Nm/each Axis motors (Z-W): 38 Nm Total power: 105 kW Rotary table: Dimensions: 2000 x 2000 mm Longitudinal travel: 1750 mm Table rotation feeds: 0,001 rpm Rotation feed: 1-1.5 rpm Motor power: 10 hP Max weight on table: 15.000 kg

RAFAMET KM 4 mechanical folding machine manufactured in Poland in 1990 is designed for producing bent sections from metal sheets with a maximum thickness of 4 mm, made by consecutive folding along the length of the workpiece strip. The highly reliable machine also allows for shaping sheet metal boxes, winding sheet metal edges and making wrapped and crimped connections after installation of special equipment. The folding machine is equipped with a control panel, back stop, workspace illumination and pedal for foot control. The machine has the same design and appearance as its twin folding machine OZAMECH KM 4. The total weight of the machine is 3750 kg. Technical parameters of the RAFAMET KM 4 folding machine - working width of the bending slats: 2000 mm - maximum workpiece length: 1500 mm - maximum workpiece thickness: 4 mm - smallest length of crimped sheet metal strip betwee ...

MACRI ITALIA PROVAR 6-45 U-D bending machine was manufactured in 2019 in Italy. The fully automatic mandrel bending machine is used in the process of machining tubes and profiles with a maximum diameter of 45 mm in 6 numerically controlled axes (X, Y, Z, B1, B2, A). Excellent process stability and workpiece quality, with the possibility of bending standard and variable (free) radiuses, are guaranteed thanks to the robust steel construction, the moving head with high-strength gears and the equipping of all machine axes with brushless servomotors. The MACRI PROVAR 6-45 U-D CNC tube bending machine is controlled using state-of-the-art MACRI software with the ability of importing files from 3D programmes and performing an anti-collision test with 3D simulation, programming of positioner force and automatic mandrel lubrication and many other useful functions. The total weight of the machi ...

(Schloemann) Beche DGH 40 Ton ( Revamped by Schuler group 2019) Manufacturer: BECHE (Schloemann) Type: DGH 40 YOM: Revamped 2019 Machine Number: 2412-HW Including 12 Ton Wellman manipulator Impact work: 40,000 mkg Total bar lift.:1.250 mm Maximum number of strokes:80 Pro Minute Average score: 6 Pro Minute Air consumption per ten blow Blow in . m in required air at the strongest hit: 6.8 Cold Air Compressor performance in m3/min: 41 Cold Air Compressor performance in m3/min:27 Hot air (160° C) Power requirement of the compressor in hp:260 Cold Air Power requirement of the compressor in hp:180 Cold Air Air tank capacity:30 m3 Steam consumption per hit with the strongest hit:3.5 kg Steam consumption per minute (saturated steam):21 kg Clear width between the guides: 1200 mm Maximum singing sounds: 2700 mm Lowest overall height of the dies without dovetail: 575 mm O ...

Equipped with no. 03 guides Overhauled with: guide grinding, CN conversion, new electrical and hydraulic system, hydraulic self-centering installation, shaving conveyor; CN Fagor 8055 Numerical Control – BT Maximum turnerable diameter 1800 mm 3-grife hydraulic self-centering with a diameter of 1450 mm with tightening force 30 Ton with 30 bar clamp L max turnerable 3000 mm Spindle engine power 110 Kw Maximum rotation speed 180 rpm Fast value axles 4000 mm/min M3/M4 Spindle Rotation Inversion Possibility 4 speed ranges Hydraulic counterpoint Maximum capacity of workpiece on counterpoint 12500 Kg It is currently possible to work details of up to 3000 mm length but the extension pallet is available to be able to work details up to 8 m in length. (un revised); Machine installed and working

MACRI ITALIA PROVAR 5-90 U-D tube bending machine, built in Italy in 2010 is used for the fully automatic process of fixed radius and variable radius workpiece bending on two different dies. The machine is characterised by a highly rigid steel structure, modern components and extensive equipment. All 5 axes of the machine (X, Y, Z, B1, B2) are equipped with reliable brushless servomotors in order to provide the user with high dynamics and excellent positioning accuracy when machining tubes and profiles with a maximum length of 5100 mm. The installed state-of-the-art MACRI software allows, among others, to program the positioner force, perform an anti-collision test with 3D simulation, import files from 3D programmes and program the speed of movement of each axis for each bend. The PROVAR 5-90 U-D mandrel bending machine weighs 6000 kg. Technical specifications of the MACRI ITALIA PROV ...

rolling capacity max.: NA t workpiece diameter: 38 mm workpiece length: 500 mm total power requirement: 24 kW weight of the machine ca.: 10 t dimensions of the machine ca.: m Max.Ø tool slide stroke 760 mm Max.Ø rack length 610 mm Length of workpiece between centres, approx. 500 mm Max. tooth width / profile width 92 mm Max. workpiece Ø 38 mm Tailstock stroke on outboard support, hydraulic, approx. 500 mm Module range 0.3 - 1.3 Total electrical load, approx. 24 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features KBH Workpiece Feed Device, standing parallel to the machine, at present set-up for feed-in and feed-out of shaft-formed workpieces, approx. Ø 16 x 200 mm long, with prism conveyor belt and lifting station for 2 shafts (blank and finished part), as well as workpiece positioning control. Originally, external gears were formed on the machine using  ...

: 26 mm : 30 mm : 30 mm threading in St 60: M 20 threading in GG 20: M 24 : MK 3 : 120-2.200 U/min. throat: 293 mm : 514x360 mm : 2 x 14 x 224 mm : 90/675 mm column diameter: 115 mm spindle stroke: 160 mm feeds: 0,1-0,2-0,3-0,4 mm/U total power requirement: 1,0/1,6 kW Machine height: 1865 mm weight: 380 kg Standard equipment: 7 TFT LCD display with touch function: manual input of spindle speed Setpoint, actual speed display, integrated drilling depth display with touch Zero point transfer, virtual drilling depth scale in the display, machine Status displays and warnings in the display, service information, selectable User language: DE / EN / FR / ES / IT / NL / RU - Thread cutting device, for thread cutting with stop, max. 6th Thread / min (thread cutting performance dependent on spindle speed), thread depth adjustable via depth stop and in the TFT - LCD display (4 tools) - Infinitely va ...

: 34 mm : 40 mm : 40 mm threading in St 60: M 24 threading in GG 20: M 30 : MK 4 : 100-1.800 U/min. throat: 300 mm : 615x430 mm : 2 x 14 x 224 mm : 138/688 mm column diameter: 145 mm spindle stroke: 160 mm feeds: 0,1-0,2-0,3-0,4 mm/U total power requirement: 1,4/2,2 kW Machine height: 1865 mm weight: 470 kg Standard equipment: 7 TFT LCD display with touch function: manual input of spindle speed Setpoint, actual speed display, integrated drilling depth display with touch Zero point transfer, virtual drilling depth scale in the display, machine Status displays and warnings in the display, service information, selectable User language: DE / EN / FR / ES / IT / NL / RU - Thread cutting device, for thread cutting with stop, max. 6th Thread / min (thread cutting performance dependent on spindle speed), thread depth adjustable via depth stop and in the TFT - LCD display (4 tools) - Infinitely v ...

The CEA ATM 18/18 was conceived to be introduced in the modern Pharmaceutical production line. It is placed after the filling and sterilization line, before the labeling and packaging line. The ampoules and/or vials are loaded manually on the loading plane of the ATM machine 18/18 by trays. The output of the rejected and approved ampoules and/or vials are respectively collected in separate trays. Formats: 1-2-5 ml Technical characteristics: • Dimension ampoules and bottles: Diameter Ø from 9 to 18 mm total height up to 100 mm • Mechanical speed: 18,000 vials/hour max. for 1 – 2 ml ampoule • Rotation speed: continuously adjustable from 500 to 3000 rpm • Power supply: 230V ± 10% 50/60 Hz 1Ph • The Client must guarantee a voltage fluctuation of no more than 10% • Absorbed power: 5 Kw • Loading/unloading plane height: 900 mm (adjustable ± 25 mm) • Dimens ...

weight max.: 1200 kg. table turning speeds: 80 - 1600 mm/min. roll diameter: 200 x 50 mm workpiece diameter: 20 - 800 mm range L-W-H: 520 x 470 x 390 mm Antrieb range L-W-H: dito mm Mitläufer volt: 230 V / 50 Hz weight: 56 kg Description: - Device for rotating and positioning Containers and cylindrical workpieces. - Unit in solid steel construction with polyurethane-coated metal rollers. - Precise speed adjustment by Frequency converter. - Foot switch for start / stop, 4-step operation. - Switch for right / left rotation. - Rotary knob for infinitely adjustable rotation speed. - Selector switch for rapid traverse / normal operation. - Switch with indicator light for operational readiness. - HF protected Scope of delivery: - 1 drive unit with control (integrated) - 1 follower The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Manitou 170 AETJL aerial work platform with 16.90 m working height The 170 AETJ-L aerial platform makes it easy to reach the most remote work areas. Equipped with an articulated structure, this model is characterized by an exceptional offset and overhang to be able to work at different heights and in different places without having to move the machine. Take advantage of the flexibility of its hydraulic movements for precise positioning in the work area! With its perforated platform floor, inclination detectors and load sensors, cylinder valves and negative braking system, the 170 AETJ-L aerial work platform allows you to carry out your work safely. This machine complies with: European Directives: 2006/42/EC - Machinery (recast EN 280:2013) - 2004/108/EC (EMC) - 2006/95/EC (Low Voltage) Make: Manitou Type: Articulated telescopic platform Type: 170 AETJ Year of construction: 20 ...

table diameter: 500 mm table load: 300 horizontal kg. table load: 150 vertikal kg. swivelling range: 0 - 90 Grad turning speeds: 0,2 - 2,5 U/min bore: 90,0 mm table height: ~ 650 mm mm motor: 230 Volt weight of the machine ca.: 90,0 kg. range L-W-H: 385 x 340 x 375 mm Furnishing: - The table can be tilted and clamped at an angle of 0 ° to 90 ° - manual tilting - Start / stop via location-independent foot switch - Direction of rotation can be selected right / left - Adjustable rotation time - The control of the welding machine via control - 350 amp ground connection Scope of delivery: - control (integrated) - foot switch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Tool changerType of gripperDouble gripper Tool changer planevertical Number of tools90 Max. tool length315 mmMax. tool diameter with occupied adjacent pockets80 mmMax. tool dia. with free neighbouring pockets160 mmWorking area 1Longitudinal735 mmCross650 mmVertical560 mmTechnical DataFeed rate longitudinal/transverse/vertical40000/40000/40000 mm/minRapid traverse longitudinal/transverse/vertical40/40/40 m/minGeneralUniversal Machining Centre in monoBLOCK construction; Control: CELOS with Siemens 840D sl Operate Floor space/WeightWeight approx.12400 KgNC swivel rotary table integrated in rigid tableType of Measuring system Direct measuring systemTable surface 800 x 650 (Ø 650) mmRotation Speed 5. Axis 20 rpm5. Axes (swivelling range) +120/-120 x 0,001 degree4. Axes (swivelling range) 360 x 0,001 degreeRotation speed max.4. Axis 40 rpmDistance between T-Slots 63 mmNumber of Slots 9Slot wi ...

GeneralUniversal Machining Centre in monoBLOCK construction; Control: CELOS with Heidenhain TNC 640 Technical DataFeed rate longitudinal/transverse/vertical40000/40000/40000 mm/minRapid traverse longitudinal/transverse/vertical40/40/40 m/minWorking area 1Longitudinal735 mmCross650 mmVertical560 mmTool changerTool changer planevertical Type of gripperDouble gripper Number of tools60 Max. tool diameter with occupied adjacent pockets80 mmMax. tool length315 mmMax. tool dia. with free neighbouring pockets160 mmFloor space/WeightWeight approx.12600 KgNC swivel rotary table integrated in rigid tableType of Measuring system Direct measuring systemTable surface 800 x 650 (Ø 650) mmRotation Speed 5. Axis 20 rpm5. Axes (swivelling range) +120/-120 x 0,001 degree4. Axes (swivelling range) 360 x 0,001 degreeRotation speed max.4. Axis 40 rpmDistance between T-Slots 63 mmNumber of Slots 9Slot width 1 ...

GeneralUniversal milling and turning machining centre with duoBLOCK construction; Control: CELOS with Siemens 840D sl Operate Technical DataFeed rate longitudinal/transverse/vertical60000/60000/60000 mm/minRapid traverse longitudinal/transverse/vertical60/60/60 m/minWorking area 1Longitudinal800 mmVertical850 mmCross1050 mmTool changerApplicationUniversal Type of magazineWheel Tool changer planehorizontal Type of gripperDouble gripper Number of tools123 NC mill-turn table with palletNC mill-turn table with pallet number of T-slots: - 1x cross slot 14 H7 / 0.55 H7 - 12x star slots 14 H12 / 0.55 H11 / 22.5° max. table speed milling operation: 30 rpm turning operation: 800 rpm integrated balancing sensor Pallet changer for 2 palletsType of Measuring system Direct measuring systemTable surface Ø 800 x 630 mmCentre bore 50 mmMaximum load (table centre) 1400 Kg4. Axes (swivelling range) 360  ...

Brush-sanding machine Fladder 300 AUT 1000 This used denibbing sander manufactured by Quickwood features a through feed design w/ vacuum feed belt and (6) horizontal mounted sanding spindles with flapper type sanders. Technical Specifications: ·         max height of the workpiece - 180 mm ·        max width of workpiece 1000 mm ·         220V 3PH main motor powers the shaft that holds ·         Variable speed spindle rotation driven by a 1/3 HP motor. ·         Variable speed vacuum belt is powered by a 2 HP motor. ·         Feed Speeds from 6 to 39 FPM. ·         Vertical shaft rotates speeds from approximately 4 to 40 RPM ·         Horizontal rotation speeds from 300 to 1 250 RPM ·         Push button controls. ·         For operation on 220V 3PH

VETTER AS16-4.0 1600 KG pillar jib crane was built in Germany in 2014. The lightweight, low-profile design combined with the electric rotation drive guarantees maximum operational comfort and a high lifting capacity for loads with a maximum weight of 1600 kg. All this makes the VETTER ASSISTENT AS pillar crane the ideal solution for many applications in limited spaces, halls and outdoor areas. Technical parameters of VETTER AS16-4.0 1600 KG pillar jib crane - maximum lifting capacity: 1600 kg - arm length: 4000 mm - maximum lifting height: 2500 mm - rotation angle: 270° - electric chain hoist - lifting class according to EN 13001: HC2 - stability class according to EN 13001: S2

: 34 mm : 40 mm : 40 mm threading in St 60: M 24 threading in GG 20: M 30 : MK 4 : 100-1.800 U/min. throat: 300 mm : 615x430 mm : 2 x 14 x 224 mm : 138/688 mm column diameter: 145 mm spindle stroke: 160 mm feeds: 0,1-0,2-0,3-0,4 mm/U total power requirement: 1,4/2,2 kW Machine height: 1865 mm weight: 470 kg Standard equipment: 7 TFT LCD display with touch function: manual input of spindle speed Setpoint, actual speed display, integrated drilling depth display with touch Zero point transfer, virtual drilling depth scale in the display, machine Status displays and warnings in the display, service information, selectable User language: DE / EN / FR / ES / IT / NL / RU - Thread cutting device, for thread cutting with stop, max. 6th Thread / min (thread cutting performance dependent on spindle speed), thread depth adjustable via depth stop and in the TFT - LCD display (4 tools) - Infinitely v ...