rest used for sale

turning diameter over bed: 660 mm turning diameter over slide rest: 420 mm turning length: 4000 (1,5m,2m,3m,5m, 6m) mm turning dia. in gap: 850 mm bed width: 560 mm spindle nose: 11 spindle bore: 103 mm transmission ratio: 3 spindle turning speed - stepless: 9-55, 37-220, 220-1320 U/min thread: 76 Stufen metrical thread cutting: 0,5 - 180 mm thread - inch: 60 - 1/6 inch. thread - module: 0,125 - 45 Whitworth-thread: 240 - 2/3 DP number of feeds: 150 mm/U longitudinal feeds:: 0,039 - 18 mm/U face feeds: 0,02 - 9 mm/U face slide travel: 410 mm upper slide-adjustment: 150 mm diameter of quill: 105 mm : MK 6 quill stroke: 225 mm total power requirement: 15 kW weight of the machine ca.: 5500 kg Huvema’s range of European production lathes. Fitted out with variable speed and fully protected. These machines are perfect for all industrial applications. Users are very enthousiastic about these  ...

turning diameter over bed: 860 mm turning diameter over slide rest: 620 mm turning length: 4000 (1,5m,2m,3m,5m, 6m) mm turning dia. in gap: 1050 mm bed width: 560 mm spindle nose: 11 spindle bore: 132 mm transmission ratio: 3 spindle turning speed - stepless: 12,5-100, 50-415,150-1250 U/min thread: 76 Stufen metrical thread cutting: 0,5 - 90 mm thread - inch: 60 - 1/3 inch. thread - module: 0,125 - 22,5 Whitworth-thread: 240 - 1 1/3 DP number of feeds: 150 mm/U rapid traverse longitudinal: 3800 mm/min longitudinal feeds:: 0,039 - 18 mm/U face feeds: 0,02 - 9 mm/U face slide travel: 432 mm upper slide-adjustment: 150 mm rapid traverse of cross-rail supports: 1900 mm/min diameter of quill: 105 mm : MK 6 quill stroke: 225 mm total power requirement: 18,5 kW weight of the machine ca.: 6300 kg Huvema’s range of European production lathes. Fitted out with variable speed and fully protected.  ...

Key data: 900 , 134 , 35

Now fully refurbished and in our stock in Wellingborough, Northamptonshire is this tie-bar-less Engel Victory 330/90 Tech injection moulding machine. Fitted with a 35mm plasticising unit which gives a maximum shot weight of 134 (PS) (g). This is a high specification machine with double core pull, CC100 controller, singe pneumatic core pull and 8 zone hot runner controller built in. It comes complete with system disks to suit the machine. The unique design of these machines allows for large tools to be installed with ease and often much larger than could go in comparable 90T machines with tie-bars. A very versatile machine with proven technology and good support from the people at Engel UK. This machine is now holding maximum lock, has no detectable wear in the plasticising unit and is cosmetically excellent. You can find out more about the work we’ve done to this specific machine by ...

Key data: 1000 , 158 , 40

In our stock in Wellingborough, Northamptonshire is this fully refurbished Arburg 420C 1000 – 250 VU injection moulding machine with vertical clamp and injection. Ideal for insert moulding as an operator can easily and ergonomically load inserts. The vertical clamp means inserts are more likely to stay in place. This machine has a 40mm plasticising unit which gives a maximum shot weight of 158 (PS) (g). As you’d expect from us, this machine has been fully refurbished and is now completely fault & leak free. With low lifetime hours of only 23k, it really is in excellent condition throughout. The plasticising unit is holding max pressure throughout the range, the pump is quiet, the platens are in great order and we’ve done great work with the general cosmetics. Machine is now available for a full demonstration as and when required. Refurbished machines from STV Machinery undergo  ...

turning diameter over bed: 400 mm turning diameter over slide rest: 264 mm turning length: 1000 mm turning diameter in the gap: 550 mm turning speeds: 44 - 2000 U/min centre height: 200 mm spindle bore: 52 mm tailstock quill taper MT: 4 MK connected load frequency: 400 V total power requirement: 1,5 / 2,4 kW weight of the machine ca.: 0,9 t dimensions of the machine ca.: 1,9 x 0,8 x 1,56 m 3-axis digital display 3-jaw chuck 200 mm. 4-jaw chuck 200 mm. Faceplate 320mm bezel fixed running bezel 4-fold steel holder. Halogen machine light machine light foot brake removable chip tray, chip protection wall Hardened and ground bed tracks Complete coolant system lining protection machine tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

control: Siemens 840-D tool taper: HSK & VDI 40 - - -: - - - - - - Vertical Turning Machine EMAG - VTC 250 DUO DD with ITC (7-30 bar) and driven tools Additional equipment: - Workpiece grippers on all 3 turrets - 12-position disc turret for driven tools and VDI 40 tool holders, - 12-station disc turret with cross-slot and VDI 40 tool holders, - 12-station disc turret for driven tools and VDI 40 tool holders, - NC steady rest, self-centering, - headstock below, - tailstock below, - chip conveyor - Knoll unit 1.500 l, - OP10: Three-jaw chuck Rhöm KFD-N 220/3, - OP20: Hainbuch Spanntop pull-back BZI65, - Live tool for axial and radial machining, - Tool holder with Capto 5 quick change system, - Artis as tool and process monitoring, The machine is in a well-maintained condition and can be inspected at any time under power. A machine video from the production plant will be shared on reques ...

turning length: 1500 mm turning diameter: 410 mm swing diameter over bed slide: 255 mm turning dia. in gap: 580 mm spindle bore: 52,0 mm turning speeds: 30 - 3000 U/min bed width: 250 mm spindle taper: 55029 D 1-6 taper in tailstock: 4 MK quill travel: 120 mm total power requirement: 5,5 kW weight of the machine ca.: 1400 kg. range L-W-H: 2530 x 1000 x 1450 mm scope of delivery : - 3-axis digital display ES-12 V with LCD display - 3-jaw steel chuck PO3-200 mm / D6 - clamping disc 350 mm - Fixed bezel - passage diam. max. 135 mm - Live steady rest - passage diam. max. 65 mm - Foot pedal with brake function according to CE - Quadruple steel holder - Protective device with quadruple steel holder - Micrometer longitudinal stop - Revolver stop with fine adjustment - Frequency converter - First filling with Shell Tellus 46 - coolant device - slip clutch - Thread clock - LED machine light - cha ...

turning diameter over bed: 680 mm turning diameter over slide rest: 415 mm turning length: 2200 mm total power requirement: 22 kW weight of the machine ca.: 6,5 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 440 mm turning diameter over slide rest: 250 mm turning length: 1000 mm spindle bore: 62 mm spindle speed:: 124 - 1400 tailstock quill taper MT: 4 quill stroke: 160 mm metrical thread cutting: 0,5 - 112 mm/U thread - inch: 1/4 - 56 inch. total power requirement: 7,5 kW weight of the machine ca.: 2,4 t dimensions of the machine ca.: 2,6 x 1,1 x 1,50 m Qick Toolholders: Face plate: 3-jaw-chuck diameter: 3-jaw-chuck diameter: Weipert precision guide and spindle lathe WG 425 The machine comes from a training company and has been maintained more than second hand. The general condition is very good, all functions have been checked. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 330 mm turning diameter over slide rest: 170 mm turning length: 800 mm spindle bore: 38 mm tailstock quill taper MT: 3 spindle turning speed - stepless: 24 - 2800 U/min linear traverse of table: 0,026 - 1,253 mm feeds crossrail-slide horizontal: 0,013 - 0,628 mm/U quill stroke: 120 mm total power requirement: 2,4 / 3,0 kW weight of the machine ca.: 850 kg dimensions of the machine ca.: 1,85 x 0,8 x 1,7 m 3-jaw chuck: Qick Toolholders: Machine Lamp: chip protection wall: Lining protection hood: Coolant System: The machine comes from a training company and was maintained more than needed. The general condition is very good, all functions have been checked. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 1100 mm turning diameter over slide rest: 780 mm turning length: 4100 mm Control: Siemens type: 840 D bed width: 710 mm faceplate: 1000 mm turning speeds: 1110 U/min total power requirement: 4,79-69 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 1300 , 177 , 40

Arburg 470C 1300-350 with 40mm plasticising unit. The ‘C’ variant of machines from Arburg is one of our most popular requests (once refurbished). These machines were market leaders for quite some time and proved reliable and good value for money over the years. With a little refurbished magic from the team to bring them back to ‘almost new’, these machines now have a new lease of life. They might not be the most energy efficient, but they are by no means power hungry and when the low upfront cost is considered with low maintenance costs, it’s a very good value option. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cos ...

turning diameter: 800 mm turning length: 4000 mm control: cnc total power requirement: kW weight of the machine ca.: 7,3 t dimensions of the machine ca.: 6,6x2,2x2 m Brand: Phoenix Type: FL 8040 CNC IT Year of make: 2001 Distance between centers: 4.000 mm Centre height: 400 mm Swing over bed: 800 mm ø Swing over support: 510 mm ø Swing in the gap: 1.100 mm ø Spindle boring: 250 mm ø Steady rest: 350 mm ø 3-Jaw chuck: 630 mm ø Machine dimensions (lxwxh): 6.500 x 2.200 x 2.000 mm Machine weight: 7.300 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 330 mm turning diameter over slide rest: 190 mm centre distance: 650 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m turning length: mm 4-jaw chuck Multifix tool holder device tail stock coolant device Technische Daten / technical details: Spitzenweite / center to center 650 mm Dreh-Ø über Bett / turning diameter over bed 330 mm Dreh-Ø über Schlitten / turning diameter over sledge 190 mm Spindelbohrung / spindle hole 36 mm Drehzahlbereich / spindle speed 30-2500 UpM /rpm Antriebsleistung / drive capacity 2,2 kW Gewicht der Maschine ca. / weight ca. 600 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 330 mm turning diameter over slide rest: 190 mm centre distance: 650 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m turning length: mm 3-jaw chuck Multifix tool holder device tail stock coolant device Technische Daten / technical details: Spitzenweite / center to center 650 mm Dreh-Ø über Bett / turning diameter over bed 330 mm Dreh-Ø über Schlitten / turning diameter over sledge 190 mm Spindelbohrung / spindle hole 36 mm Drehzahlbereich / spindle speed 30-2500 UpM /rpm Antriebsleistung / drive capacity 2,2 kW Gewicht der Maschine ca. / weight ca. 600 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

• FATOSA automatic chopper model PA-130. • Automatic feeding system by loading hopper and tapered feeding spindle, to output spindle, plate carrier and cutting blades. • Perfect chopping without rubbing or bruising, characteristics that, together with its great robustness, make it stand out from the rest of the machines on the market. • The machine is designed for mincing meat, fish, vegetables... • The minimum temperature at which the products to be chopped can be will depend on the motor power chosen, the diameter of the holes in the outlet plate and the combination of plates and blades that has been mounted. • Push-button control panel. • General power switch • Made entirely of AISI-304 stainless steel • Gearbox transmission with hardened and ground shafts, mounted on bearings and gears in oil bath. Alloy steel knife shaft suitable for bending and torsional ...

Available in stock 1 x Complete Containerized Gas Power Plant based on 1 x 725 kW Guascor FGLD 480. The power plant is mounted in a 40 ft container with its corresponding alternator, gas connection with regulation system, electronic control system and rest of auxiliaries (batteries, refrigerators, switches and control cabinets). Manuals and electrical diagrams are also available. The unit is in our warehouse - ready to go. Equipment in good working conditions.

turning diameter over bed: 300 mm turning diameter over slide rest: 150 mm turning length: 800 mm spindle bore: mm turning speed range: 42 - 2000 U/min feeds: 0,011 - 0,91 mm/U tailstock quill taper MT: 3 total power requirement: 2,2 kW weight of the machine ca.: 0,75 t dimensions of the machine ca.: 1,7 x 0,8 x 2,0 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning length: 750 mm turning diameter: 400 mm centre height: 165 mm turning diameter over slide rest: 190 mm spindle bore: 32,0 mm tailstock quill taper MT: 3 MK turning speeds: 85 - 2200 U/min bed width: 200 mm total power requirement: 2,2 kW weight of the machine ca.: 770 kg range L-W-H: 1985 x 890 x 1195 mm New price ~ 23.000 euros from a training workshop () Furnishing: - Spindle speed continuously adjustable in 2x switching stages - TOS 3-jaw lathe chuck Ø 160 mm, with spare jaws & chuck key - NEWALL digital display, front left - MULTIFIX steel holder with inserts - Movable tailstock - live center, incl. quick-action drill chuck - digital speed display - Change gears - Foot/spindle brake all technical data: - Turning diameter over bed 400 mm - Distance between centers 750 mm - Center height 165 mm - Spindle bore 32 mm - Turning diameter over cross slide 190 mm - bed width 200  ...

Automated system for picking packs of bottles or cartons from a pallet. The equipment ensures continuous feeding of empty bottles to the rest of the line. Safety light curtain. UniOP control panel. History, documentation and wiring diagram available

turning diameter over bed: 590 mm centre distance: 4000 mm turning diameter over slide rest: / mm total power requirement: / kW weight of the machine ca.: / t required space: / m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 6 Monate ab Auftragse : Bulgarien : 78300 € : 1566 € : 760 mm : 3000 mm : 380 mm : 132 mm : 520 mm : 560 mm : 11 : 140 M : 3 : 7 - 42, 28 - 170, 165 - 1 U/Min : 150 : 0.039 mm/U : 0.02 mm/U : 0.5 - 180 mm : 60 - 1/6 Gänge/ : 0.125 - 45 : 2 - 240 : 410 mm : 150 mm : 105 mm : 6 MK : 225 mm : 15 kW : 4470 kg driven by variable speed control (3 steps) 3-axes digital readout FAGOR with CSS (constant surface speed) quick change toolpostAmestra type Multifix with 4 holders (3 square, 1 round) 3-jaw chuck Bison3295/DIN6350, Ø 400 mm spindle dead center main motor with frequency invertor four way rapid traverse device foot pedal brake longitudinal stop for 1 position steady and following rest coolant equipment full length rear splash guard leadscrew and shaft protection safety guard for the chuck toolholder guard levelling bolts and plates quick release tailstock tailstock quill ...

Welding fume extraction table Welding table DCE UMA150HG5 dedusting Welding table with integrated suction with filter Manufacturer dust control equipment dust collectors Type UMA 150H G5 Rest according to photos

Working hours : 18831 h Maxi diameter over bench : 920 mm Maxi diameter over carriage : 745 mm Maxi turning diameter : 550 mm Distance between centers : 1416 mm Stroke X : 315 mm Storke Z : 1350 mm Rapid speed X/Z : 30 m/min Spindle speed : 3000 rpm Spindle bore : 95mm Turret : 12 posts ACCESSORIES : Steady rest Living tools Chip conveyor Tailstock Lot of tooling

Freight lift according to MRL ConVer 147.01 with instructed accompanying person. Payload 1.200kg. 2 stops 0-4117mm. Car size 2800x2860x2000mm. Colour framework RAL 7043 Rest RAL 7035. Access bottom front top front and rear. Price without assembly, TÜV and freight, pure only the machine. The machine can also be adjusted on request, e.g. conveying height. Here, the selling price would then have to be determined.

Distance between centers: 1000 mm Centers height: 200 mm Swing over bed: 500 mm Swing over slide: 448 mm Swing over cross slide: 220 mm Spindle inner hole diam: 50 mm Main motor power: 12.5 kw Equipped with: 3-jaw chuck: Ø 260 mm Sets of jaws: 2 sets Steady rest: 1 Cutting oil tank: Yes

Spinner TC110L-MCY CNC Lathe C and Y axis 1700 mm length Machine is in quite good condition Live tools are not included steady rest is included Fanuc Control

Manufacturer DOOSAN Model PUMA 3100L Year / Month 2013 / 07 CNC FANUC i SERIES Capacities Ø Swing over bed 850 mm. Ø over front door 720 mm. Ø swing over cross-slide 670 mm Max turning diameter 525 mm. Max turning length 1280 mm. Chuck size 12.5” Bar working diameter 102 mm. Travels and feedrates X travel 293 mm. Z travel 1.280 mm. Rapid traverse rate X/ Z Axis 30 m/min. Main spindle Max spindle speed 2.800 rpm Speed ranges 2 Main spindle power 22 kW Main spindle torque 6.605 Nm Spidle nose A2 – 11 Turret No of tool stations 10 Turret tool size 25 x 25 mm Max boring bar size 50 mm. Indexing Time 0,15 s Tailstock Quill diameter 100 mm Quill travel 100 mm Quill bore taper MT#5 Equipment Chip conveyor INCLUDED 3 Jaw-Hydraulic chuck Ø315 mm INCLUDED Automatic Tool pre-setter INCLUDED Hydraulic steady rest SMW Autoblock SLU-X-3.2-MS Others T ...

turning diameter over bed: 540 mm turning diameter over slide rest: 270 mm turning length: 2500 mm spindle passage: 60 mm turning speeds: 600 U/min Rapid travel: steady for max. workpiece diameter from: 270 mm steady for max. workpiece diameter from: 170 mm faceplate: mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 820 mm turning diameter over slide rest: 600 mm turning length: 5000 mm faceplate: 750 mm spindle passage: 125 mm turning speeds: 9-450 U/min Rapid travel: steady for max. workpiece diameter from: 520 mm steady for max. workpiece diameter from: 330 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 820 mm turning diameter over slide rest: 600 mm turning length: 7300 mm faceplate: 800 mm spindle passage: 92 mm turning speeds: 9-450 U/min Rapid travel: steady for max. workpiece diameter from: 530 mm steady for max. workpiece diameter from: 330 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 630 mm turning diameter over slide rest: 380 mm turning length: 400 mm spindle passage: 105 mm turning speeds: 24-1800 U/min Rapid travel: steady for max. workpiece diameter from: 340 mm 3 jaw chuck Forckrath: 315 mm throat: 700 mm length of gap: 300 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Cool Compact Magnos 650 Refrigerator with Glass Door  Versatile convection refrigerator  excellent for commercial kitchens, restaurants, butchers, bakeries Cool Compact Refrigerator Magnos 650 with Glass Door suitable for use with GN 2/1 containers (grid size 530 x 650) with convection cooling and electronic control inside/outside CNS 18/10 ( also back wall, bottom and cover plate ) Warning by visual and acoustic signal Compressor Protection Function suitable for the tropics - suitable for ambient temperatures up to 43ºC Automatic evaporation of condensation by hot gas Cooling body made of one piece high-pressure foamed self-closing and lockable door, door hinge on the right Evaporator-free interior Drawers with telescopic full-extension extensions made of stainless steel 1.4509 Very stable drawer guide: loadable up to 60 kg Electronic control with 4 top performanc ...

Grinding diameter: 630 mm Grinding length: 4000 mm Workpiece weight: 900 kg CNC Brand: Siemens CNC Model: SIEMENS 840D 4 Axis controlled X, U, Z and C Axis Large steady rest package 6 units Concave grinding Covex grinding Dressing system Rebuild by Primoteq Centre height:           315mm Grinding Ø:              630mm Grinding length:         4000mm Grinding stone dimensions:710 x 80 x 305mm Table inclasement:       -5 to + 5° Tailstock:               6Mk Coolant system:          Yes Filtration:              Yes Length:                  12000mm Width:                  &nb ...

Linck 700 x 100 edger - German production - hydraulic disc shifting TECHNICAL PARAMETERS: - cutting width max 550 mm - cutting height max 100 mm - element width max 700 mm - engine power 22 kW - feed smoothly adjustable from 10 - 60 m/min - working length of the fixed sleeve 120 mm - working length of the movable sleeve 120 mm - minimum element length 600 mm - disc diameter max 350 mm - spindle diameter 55 mm - sleeve diameter 85 mm - spindle with steady rest - two upper pulling rollers - two lower pulling rollers - two auxiliary rollers in the tabletop - feeder length 3700 mm - feeder width 700 mm - four rollers in the table - adjustment of the disc spacing from the feeder - a row of anti-kickback pawls Transport dimensions 380x220x150 cm weight ~ 2000 kg

Turning diameter: 770 mm Turning length: 2155 mm Turret positions: 12 CNC Brand: Fanuc CNC Model: Fanuc SMW Autoblock chuck Tool eye SMW Autoblock steady rest Chip conveyor Ca. 11.000 Cutting hours Max. turning Ø: 770mm X-Axis:         357mm Z-Axis:         2155mm Spindle bore:   132mm Speedrange:     2000Rpm Spindle power:  30kW ATC / revolver: 12 Speed live tools:4000Rpm Power live tools:7.5kW Chip conveyor:  Yes Tool eye:       Yes Pinole taper:   6Mk Stroke pinole:  120mm Length:         5702mm Width:          2440mm Height:         2292mm Weight:         9700kg

Turning diameter: 850 mm Turning length: 3190 mm Turret positions: 12 CNC Brand: Fanuc 2 x SMW Autoblock chuck Tool eye SMW Autoblock steady rest Chip conveyor Ca. 1000 Cutting hours Max. turning Ø: 850mm X-Axis:         293mm Y-Axis:         130mm Z-Axis:         3190mm Spindle bore:   115mm Speedrange:     2800Rpm Spindle power:  30kW ATC / revolver: 12 Speed live tools:7.5Rpm Chip conveyor:  Yes Tool eye:       Yes Pinole taper:   5Mk Stroke pinole:  120mm Quill Ø:        120mm Length:         6585mm Width:          2280mm Height:         2315mm Weight:         12300kg

Center height: 570 mm Center distance: 2000 mm Spindle bore: 62 mm 3 chuck and 4 chuck Dr. Heidenhain Digital readout Steady rest Feeds all 3 directions Swing over bed Ø:        570mm Swing over cross slide Ø:365mm DBC Turning Length:      2000mm Spindle bore:            62mm Spindle power:           15kW Bed width:               360mm Tailstock spindle Ø:     80Ø Spindle taper:           5Mk Speeds / ranges:         2240Rpm Length:                  5000mm Width:                   2100mm Height:                  2200mm Weigh ...

Turning diameter: 870 mm Turning length: 3000 mm Turret positions: 0 CNC Brand: Fagor CNC Model: Fagor 8055 Work load between centrers 2800 Kg Fixed steady rest 2 x  Coolant system Quick chnage tool post Swing over bed Ø:        870mm Swing over cross slide Ø:560mm Swing in the gap Ø:      910mm DBC Turning Length:      3000mm Gap length:              325mm Spindle bore:            105mm Spindle power:           37kW Bed width:               550mm Tailstock spindle Ø:     140Ø Spindle taper:           5Mk Speeds / ranges:         1400Rpm Length:                &nbs ...

This Geminis GHT 11 G4 2200x8000 Lathe was manufactured in the year 2010. It is equipped with a Fagor 8070 control unit and has 2 axis. The machine has a spindle bore of 162 mm, it includes a steady rest, chip extractor, electronic handwheel, machine leveling supports, and various turret tool holders as additional equipment.

Grinding diameter: 600 mm Grinding length: 5000 mm Workpiece weight: 5000 kg Cylicrical grinder with table inclesment C-Type open steady rest Work load up to 5000 Kg Table speed 1 - 6 M/min Headstock 120 Rp  Centre height:           310mm Grinding Ø:              600mm Grinding length:         5000mm Grinding stone dimensions:750 x 100mm Table inclasement:       0 - 6° Length:                  9900mm Width:                   2300mm Height:                  2200mm Weight:                  19000kg

turning diameter over bed: 3200 mm turning diameter over slide rest: 2400 mm turning length: 15000 mm faceplate diameter: 2600 mm control: Siemens 840 Dsl workpiece weight max.: 80000 kg accuracy +/-: bis/up to: 0,01 mm spindle motor: 110 kW faceplate speeds from - to: 0-50 U/min total power requirement: - kW weight of the machine ca.: 60 t overhauled and modernized 2009 & 2012/2013 equipped with: - CNC control Siemens 840D SL - 2 supports with 1 controller each - 4-jaw face plate - 2 hydraulic steady rests - hydraulic tailstock Machine is dismantled and stored. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Grinding diameter: 440 mm Grinding length: 1000 mm Workpiece weight: 200 kg Digital readout 2 axis Steady rest 2 x  Dressing attachment U Wheel head 0 - 180 Gr Counter tailstock fine adjsutment Mk3 / 30 mm Centre height:                          225mm Grinding Ø:                             440mm Grinding length:                        1000mm Grinding stone dimensions:              400 x 80 x 127mm Grinding stone speeds:                  1000Rpm Table inclasement:                      8.5° Tailstock:          ...

x-travel: 6300 mm y-travel: 2200 mm workpiece height: 1835 mm Table area: 6000x1835 mm Rest: 2 Side head: 2 number of T-slots: 7 T-slot - distance: 240 mm T-slot - width: 28 mm bed length: 14650 mm column daylight: 2075 mm feed: 5-60 m/min workpiece weight: 15000 kg total power requirement: kW weight of the machine ca.: 55 t dimensions of the machine ca.: 14,65x4,37x4,05 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

We offer a Doka Frami wall and foundation formwork 206,505m² complete with many accessories. The formwork is 90% newly covered with new Finply birch cladding 220- 240g/m²phenolic resin coating. The rest of the elements are checked and sorted and covered with original Doka Xlife formwork. Exposed concrete class 2/3 possible without any problems. New value approx. 160.592,60€, special net price 41.498,15€ Piece Description 19 Frami Xlife-Element 0.30x1.50m new plywood 2 Frami Xlife-Element 0.45x1.50m new plywood 51 Frami Xlife-Element 0,60x1,50m new plywood 35 Frami Xlife-Element 0.75x1.50m new plywood 2 Frami Xlife-Element 0.75x1.50m used top xlife 7 Frami Xlife-Element 0,90x1,50m used top xlife 6 Frami Xlife-Element 0.90x1.50m new plywood 11 Frami inner corner 1,50m 20cm inner corner 7 Frami outer corner 1.50m outer corner 1 Frami hinge corner A galvanized  ...

This DOOSAN PUMA 700L lathe was manufactured in 2020. It features a FANUC control unit, maximum swing of 1030 mm, and a cutting length up to 3200 mm. The machine is equipped with a chip conveyor and a steady rest, enhancing its robust turning capabilities. With a bar capacity of 164 mm and chuck size of 609 mm, it efficiently handles substantial workpieces. Consider buying this DOOSAN PUMA 700L lathe. Reach out for more information.

turning diameter over bed: 500-600 mm turning diameter over slide rest: / mm turning length: 2800 mm bore diameter: 130 mm total power requirement: / kW weight of the machine ca.: 5,25 t required space: / m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over slide rest:280 mm turning length:4000 mm total power requirement:7,8 kW weight of the machine ca.:6 t dimensions of the machine ca.:5,9 x 1,9 x 1,40 m

HNK HCL 41x14 crankshaft CNC lathe Max. Swing Dia. Over Carriage Ø4,100mm Max. Center Distance 14,000mm Chucking Ø700~2,000 mm Steady Rest Ø510~860mm Max. Loading 160Ton

Center width: 1500mm, max. chuck diameter: 200/240mm, motor power: 4kW, including steady rest, on-site inspection is possible.