129,247 used machines on RESALE, but how to find them? Machine Search
REP model V68 Y20W vertical rubber injection presses, Type G8, year 2003, Clamp force 4000kN, Platen size: 630 x 800mm, Distance between columns: 730/440mm, Daylight: approx 1000mm, Injection unit type Y2000, Piston dia 81.5mm, Shot capacity: 2000cm3, Injection pressure: 1500 Bar Top and bottom ejectors. O/a dimensions: 2950mm x 1410mm x 4800mm high, weight approx 12000kgs. Complete and in very good condition (not operated for over 2 years).
used
1 x Repiquet 2550mm wide x 820mm dia 4 roll inverted L Calender, Machine type: CALANDRE 4 CYL DE 820 x 2550, Machine no. 70-C9-87 Motorised nip adjustment, Peripherally drilled rolls, High pressure hot water hearing Bush bearings with flood lubrication, Hydraulic pre-loading to all rolls, Roll bending and unbending on roll 4, Cross axis on roll 3 and 1. Automatic bank sensors/control + camera system Traversing unit for roll buffing or sand blasting. 'Citroen' unidrive gearbox, type: SPECIAL, order no. 50491, Power 140/240 C.V. Speed 1500/2250, Output 46/59 with individual motor to each roll- Roll 1 and 4 - 130HP, Roll 2 and 3 - 240HP, Max calender speed 120m/min. Dual embossing station with approx 25 x embossing rolls (+ 5 x rubber pressure rollers) In very good condition.
ID3356 Corrosion repair framework year/Baujahr 2021 25-28 t Corrosion repair framework Corrosion Touch Up Scaffolding
Force of pressure: 100 t projection: 350 mm table size: 690 x 840 mm Durchfalloch in the table: 160 mm table adjustment: slide area: 450 x 600 mm slide adjustment: 80 mm stroke adjustment: 8-100 mm stroke rate: 60 / min drive motor: 380 V, 5.5 kW space: 1850 x 1850 x 2650 mm weight: 6800 kg
pressure: 200 t distance between columns: 1600 mm max. ram stroke: 600 mm dayligth: 900 mm table width: 1600 mm table depth: 1300 mm table height: 1060 mm ram surface: 1600 x 1300 mm T-slots: Din 650 / 22H12 rapid traverse: 400 mm/s return speed: 325 mm/s pressing speed: 42 mm/s bei 40% mm/sec pressing speed: 20 mm/s bei 100% mm/sec die-cushion pressure: 800 kN die cushion stroke: 150 mm speed of die cushion: auf 68/ ab 225 mm/s The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
closing pressure:6600 kN weight of the machine ca.:45,5 t
cleaned & checked 220 Volt / 1500 Watt / 50-60 cycles (Hz)
REP H48Y10W Horizontal Injection Moulding Machine Year of construction 2005 Machine Parameters Volume [cm3] 1000 Clamping force [kN] 1930 Injection pressure [bar] 1500 Moulds dimension [mm] 450x450 Tonnage 1.9t Platen size: 450x450 Cycles: 2,220,383 General condition: operational Dims [mm]: 4200 L x 1400 W x 2200 H Weight [kg]: 6750
Rotary indexing table with 12 stations Automatic ejector three pressing stages Pressure capacity 1,000 KN Stroke 12-120 mm Stroke rate 30-60 1/min Plunger adjustment 80 mm Total weight 9,500 kg
PackLab WING REPC FWB60 self-adhesive labelling machine for front & back labelling for cylindrical, oval or rectangular shaped bottles, etc., 2 label applicator type M60 DX 250, label speed 60 m/min., outer diameter of the label reel max. 400 mm, core diameter of the label reel 45-75 mm, label carrier tape with a maximun height of 250 mm, label width from 15 up to 480 mm, maximum label height approx. 245 mm, conveyor width 80 mm, top stabelising belt, press-on belt with a height of approx. 110 mm, electrics 400V/50Hz/3PH, machine floor space approx. 4140 x 3000 mm (LxW), machine height approx. 1900 mm, machine net weight approx. 950 kg
CNC – controlled profile and tube bending machine for demanding and precise bending work with hollow sections and tubes. With our machines, aluminium – steel / stainless steel – various plastics such as PVC window profiles (depending on the application) can be bent with repeatable accuracy, regardless of the material. Depending on the equipment, our machines can also be used for three-dimensional bending work. Our REPANDUS models can work both horizontally and vertically. The models of the REPANDUS series work with a fixed upper roller and two movable lower rollers – this means that the straight end piece is relatively short compared to machine concepts with fixed lower rollers. The machine body is made of vibration-absorbing cast steel Shaft diameter of upper and lower rollers Ø 70 mm Shafts made of special steel – hardened and ground Bending force 190 kN Maximu ...
CNC – controlled profile and tube bending machine for demanding and precise bending work with hollow sections and tubes. With our machines, aluminium – steel / stainless steel – various plastics such as PVC window profiles (depending on the application) can be bent with repeatable accuracy, regardless of the material. Depending on the equipment, our machines can also be used for three-dimensional bending work. Our REPANDUS models can work both horizontally and vertically. The models of the REPANDUS series work with a fixed upper roller and two movable lower rollers – this means that the straight end piece is relatively short compared to machine concepts with fixed lower rollers. The machine body is made of vibration-absorbing cast steel Shaft diameter of upper and lower rollers Ø 70 mm Shafts made of special steel – hardened and ground Bending force 190 kN Maximu ...
clamping force: 400 kN injection volume: 125 cm³ screw diameter: -- mm platen size: 300 x 300 mm Condition: used, Specification: C-frame injection moulding machine for TPV - second-hand clamping unit: - Clamping unit: vertical - Tonnage: 40 t - clamping force: 400 kN - Heating platen size: 300 x 300 mm Injection unit: - Injection volume max.: 125 cm³ - Connected load: 3x 400 V, 50 Hz 76A fuse protection (incl. peripherals) - Pump output: 7.5 kW, 14.9 A - Total output: 28 kW Dimensions L/W/H approx.: 2,000 x 1,500 x 2,500 mm Weight approx.: 2,250 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
REP Press Model V58Y10W Injection volume 1000ccm Platen size: 500 x 630 mm Year 2006 Power: 2550 kN Operating hours: 14570 Moveable traverse Fix traverse Sliding Table
range L-W-H: 960 x 460 x 860 mm weight: 75 kg : 8 St. Tool trolley with 8 drawers, all with tools. - The pull-out drawers are all ball-bearing. - The entire workshop trolley is lockable. - The workshop trolley has 4 stable castors, 2 steerable and lockable. - The tools included are made of chrome vanadium steel. - The workshop trolley has 4 stable castors, 2 steerable, 2 lockable, which ensure very comfortable rolling. On the tool trolley there is a stable worktop made of polypropylene plastic. - The tools included in the workshop trolley are made of chrome vanadium steel and are stored in Styrofoam/foam inserts. + Drawer 1: - 1/4 inch: 13 nuts from 4mm to 14mm, 11 long nuts 4mm – 13mm Ratchet, universal joint, extension. - 3/8 inch: 10 nuts from 10mm to 19mm, 11 long nuts from 6mm to 19mm Ratchet, universal joint, extension. - 1/2 inch: 17 nuts from 8mm to 32mm, 9 long nuts from 10mm ...
clamping force: 400 kN injection volume: 125 cm³ screw diameter: -- mm platen size: 600 x 400 mm Condition: used, Specification: C-frame injection moulding machine for TPV - second-hand clamping unit: - Clamping unit: vertical - Tonnage: 40 t - clamping force: 400 kN - Heating platen size: 600 x 400 mm Injection unit: - Injection volume max.: 125 cm³ - Connected load: 3x 400 V, 50 Hz 90A fuse protection Approx. dimensions: 1,550 x 1,050 x 3,120 mm Weight approx.: 2,250 kg Two identical systems are available. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
clamping force: 400 kN injection volume: 125 cm³ screw diameter: -- mm platen size: 550 x 400 mm Condition: used, Specification: C-frame injection moulding machine for TPV - second-hand, Modell TTV-C40-125 C40P01B clamping unit: - Clamping unit: vertical - Tonnage: 40 t - clamping force: 400 kN - Heating platen size: 550 x 400 mm Injection unit: - Injection volume max.: 125 cm³ - Connected load: 3x 400 V, 50 Hz 90A fuse protection Approx. dimensions: 1,550 x 1,050 x 3,120 mm Weight approx.: 3,200 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
ID3411 Crane Repair Spreader for 20ft Container year/Baujahr 2016 - brand new, unused 1.5 t Spreader to move sea container 20Ft, SWL: 40.000 Kg, is completely new never used Move spreader to sea container 20Ft, SWL: 40,000 Kg, is completely new never used
pressure: 200 t throat: 450 mm stroke: 30 - 140 mm table surface area: 1100 x 850 mm dayligth: 500 mm ram surface: 800 x 600 mm ram adjustment: 110 mm tool hole in ram: Durchm. 65 x Tiefe 105 mm no. of strokes: 45 Hub/min total power requirement: 15 kW weight of the machine ca.: 14,2 t dimensions of machine L x W x H: 3,18 x 2,09 x 3,05 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
We are selling a large-capacity 3D printer X1000 from German RepRap GmbH. The device is in good condition and has been serviced by Innovatiq., Scope of delivery:, - 1 pc. 3D printer X1000, - Small parts and remaining consumables, Installation space in mm (x/y/z): 1000 x 800 x 600 mm, build speed: 10 â 150 mm/s, Travel speed: 10 â 300mm/s, Layer thickness: 0.02mm, Filament diameter: 1,75 mm, Nozzle diameter: 0.4mm / 0.6mm / 0.8mm, extruder units: DD3 Dual, Extruder temperature: max.290°C, Print bed technology: Heatable up to 120°C, Data transfer/network: LC touch display, wireless printing via WLAN, Ethernet, software: Simplify3D Software, Power consumption: (max.) 2.5kW, approx. 30% in continuous operation, Power connection: Three-phase current 400V (CEE 3L+N+PE), 16 A, Dimensions in mm (w x h x d): 1725 x 1500 x 1320 mm, Weight in kg: 400 kg
Inv. Num. : 8583 Type: REP 100 Producer: Heilbronn Created: 1989 Parameters: Compressive force: 100 t Stroke length: 6-100 mm Maximum stroke rate per minute: 100 1/min Total power requirement: 11 kW Machine weight: 7000 kg
Rep M46 Injection Moulding Machine Size of platens 430x430mm Injection unit short volume 670cm3 Injection pressure 1690 bar Injection force 331kN
pressure:100 t throat:350 mm stroke:6 - 100 mm no. of strokes:60 /min distance table/ram, max. stroke up, adjustment up:400 mm table surface area:850 x 700 mm hole in the table:470 x 150 mm table height over floor:855 mm ram surface:450 x 300 mm ram adjustment:80 mm power requirement:7,5 kW weight:5,0 t dimensions (WxDxH):1,5 x 2,3 x 2,6 m German Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 clutch:pneumatic overload protection in ram:mechanical
Pressure:080 t throat:300 mm stroke:8 - 100 mm no. of strokes:60 /min distance table/ram, max. stroke up, adjustment up:440 mm table surface area:720 x 600 mm hole in the table:300 x 175 mm table height over floor:860 mm ram surface:400 x 270 mm ram adjustment:60 mm power requirement:7,5 kW weight:6,0 t dimensions (WxDxH):1,3 x 2,2 x 3,05 m German Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 clutch-/ brake combination:hydraulic, Ortlinghaus overload protection in ram:hydraulic ram adjustment:motoric ram counterbalance:pneumatic
pressure:160 t throat:690 mm stroke:8 - 180 mm no. of strokes:50 /min distance table/ram, max. stroke up, adjustment up:500 mm table surface area:1300 x 1000 mm hole in the table:400 / 120 mm table height over floor:850 mm passage to the back:900 mm ram surface:1000 x 700 mm ram adjustment:130 mm power requirement:11,0 kW weight:19,0 t dimensions (WxDxH):2,4 x 2,8 x 3,4 m German Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 clutch:pneumatic ram adjustment:motoric ram counterbalance:pneumatic
Technical data: Make: Moehringer Width: 1600 mm Length: 6000 mm - with pneumatic belt repeller Pictures and further information on request
We offer complete recondioned Scania engines in exchange
Industrial replacement monitor 12.1 TFT monitor High-quality anti reflective glass incl. cable with 15-pin. D-Sub-Plug Technical Data: TFT-LCD Monitor 12.1 inch Display/Resolution 800 x 600 Pixels Brightness 400 cd/m2 Contrast ratio 500:1 Response time 8 ms Frequency 60 hz Display range 246 x 185 mm External power supply 12V Operating power unit -10c +60 celectricity consumption max. 30 W connection D-Sub 15-pol, 2 row OSD control Brightness, contrast control, auto-adjustment phase position, clock, instalment speech, reset connection cable, power supply The Front panel is not included in the offer. The installation is carried out on the existing front panel. 24 Month Warranty! More monitors, new and used on request! ; New!
Key data: 420 , 525 , 400
Execution: unit type: mobile version: Schallgedämmt technical data motor: motor manufacturer: one motor type: D 2842 LE engine power: 424 KW cooling: water-cooled starting: electric 24 V DC speed: 1500 rpm fuel: fuel oil EN 590 Technis Che data generator: generator manufacturer: Ansaldo FKI generator type: M 7B 316 LD 4 generator power: 525 kVA voltage: 400 / 231 volts power factor: cos. -phi 0.8 speed: 1500 rpm switchgear: execution: auto-start features: peak-load operation switch: generator switch 3 pin delivery: built tank: execution: double-walled litres: 1,000 dimensions of the unit: width approx. mm: 2350 height mm: 3.260 length mm: 9.230 weight KG: 10,600 use: State: well get built: 1992 delivery: immediately Verl price net in â?¬: on request: hours of operation: 701 location: Verl - Germany
<b>Properties</b> Used belt of manufacturer TRANS standard <b>Technical data:</b> Mass of the belt conveyor Specification no.: U1009424-V0091 Nominal radius/inner radius: 600 mm Width: 900 mm Nominal angle/slope angle: 180Grad Strap type: KT96 Förderhöhendiff.: 500mm <b>Belt conveyors</b> The belt is ideal to dovetail machines or jobs in the picking zone and to optimize the internal process. Transportation can foster the belt conveyor sensitive and different-sized containers, boxes or other packaging and article units to the task or delivery point and, for example, also serves as a connecting route before or between production and Woodworking machines. Also enables efficient parts in operating and storage and is designed to promote significant flow rates and distances.
PLC control, connection module for digital electronic modules, terminal module, repeater -Manufacturer: Siemens, RS 485 repeater -Type: 6ES7 972-0AA01-OXAO E-Stand:4 -Dimensions: 65/45/H125 mm -Weight: 0.3 kg
<b>Properties</b> Used belt of manufacturer TRANS standard <b>Technical data:</b> Mass of the belt Specification no.: U1009424-V0520 Nominal radius/inner radius: 600 mm Width: 900 mm Nominal angle/slope angle: 180Grad Strap type: KT96 <b>Belt conveyors</b> The belt is ideal to dovetail machines or jobs in the picking zone and to optimize the internal process. Transportation can foster the belt conveyor sensitive and different-sized containers, boxes or other packaging and article units to the task or delivery point and, for example, also serves as a connecting route before or between production and Woodworking machines. Also enables efficient parts in operating and storage and is designed to promote significant flow rates and distances.
Channel folding machine, folding machine, folding former, seam closing machine, folding former, sheet metal bending machine, profiling machine -Rolls: 20 -Distance rings: 14 -Executions: different -Take: Ø 28 mm -Price: complete -Weight: 21.4 kg
OFFFER OF THE FOLGENDEN ARTIKEL Number: SD001 Number: 1 apiece Shoe repair centre (cleaning machine, etc.) Factory: Hardo Type: unknown/no type recognizable Accessories: various accessories (see pictures) Dimensions above all: Width 1540 mm x height: 1790 mm x Tife: 790 mm State Note! See also the Foto/photos about the condition. Note! Only the described item is sold. Nothing else that can be seen in the pictures.
Channel folding machine, folding machine, folding former, seam locking machine, folding former, sheet metal bending machine, profiling machine -Number: 14 pieces rolls -various: versions -Recording: Ø 28 mm -Price: complete -Weight: 22.5 kg
Ring bending machine, profile bending machine, three-roll bending machine, bending machine -Outer diameter: 200 mm -for: 35 mm pipe -Bearing seat: Ø 55 mm -Bore: Ø 49 mm -Quantity: 2 rolls available Price: complete -Dimensions: Ø 200 x 81 mm -Weight: 11 kg
Replacement blades for cutting machines -Knife size: 127x25.4x1.1mm -Urschel: 46097 -Number: 33x available -Price: per piece -Weight: 25 g/piece
Film recycling and granulation plant Material: PE, PP, // Cascade extruder, snail/LD x 220+150/ x 26D, drives 232 & 99 kW, water separator, hot tee with underwater cooling, only 8,500 operating hours
Replacement columns for die-casting machine OL1500, D250x12, Oleopress, used - overhauled Special price! Attention: The current new price is certainly twice as high. In addition, we also have a new spar nut and 2 adjusting nuts in separate adverts. If you have a VAT number, we will be happy to issue you with an invoice without VAT. Second hand! The part was bought from a spare parts store of a company, it was overhouled by a specialist company, is in a very good condition and fully functional. Attention: We have not cleaned the column yet, as the fat layer is optimal for storage. Material 25CrMo4 Manufacturer Olepress / O.P. DIE Casting Thread 250 x 12mm Thread fixed end 300mm lg Thread adjustable end 1160mm lg Weight approx. 2300 kg Attention: We offer various columns, adjusting nuts, tie bar expansion nuts and 2-piece nuts from: IDRA D330, D300, D260, D250 ...
Replacement columns for die-casting machine OL1600, D250x14, Idra, new -50% Special price! Attention: The current new price is certainly twice as high. If you have a VAT number, we will be happy to issue you an invoice without VAT. As good as new in original packaging! The part was bought from a spare parts store of a company and has never been in use, is completely as new and in the original packaging. Material 25CrMo4 Manufacturer Olepress / O.P. DIE Casting Thread 250 x 14 mm, L 5908 mm, Thread fixed end 290mm lg Thread adjustable end ca. 1160mm lg Weight approx. 2300 kg Attention: We offer various columns, adjusting nuts, tie bar expansion nuts and 2-piece nuts from: IDRA D330, D300, D260, D250, Oleopress/OP Die Casting: D285, D250, Frech: D375, D330, D300
Replacement blades for cutting machines -Manufacturer: Stumabo -Blade size: 127x25.4x1.5 2GØ10.4 (90°) -Quantity: 25x available -Price: per piece -Minimum order quantity: 3 pieces -Weight: 25 g
Replacement columns for aluminium die-casting machine OL2000, D285x10, Oleopress, new -50% Special price! Attention: The current new price is certainly twice as high. In addition, we also have a spar nut and 2 adjusting nuts in separate adverts. If you have a VAT number, we will be happy to issue you with an invoice without VAT. As good as new in original packaging! The part was bought from a spare parts store of a company and has never been in use, is completely new and in ist original packaging. Material 25CrMo4 Manufacturer Olepress / O.P. DIE Casting Thread 285 x 10mm, L 6830mm Weight approx. 3400 kg Attention: We offer various columns, adjusting nuts, tie bar expansion nuts and 2-piece nuts from: IDRA D330, D300, D260, D250, Oleopress/OP Die Casting: D285, D250, Frech: D375, D330, D300
Replacement blades for cutting machines -Knife size: 205x125x1.47 -Type: 676 FB99262 -Number: 18x available -Price: per piece
used
Used first-class renovated extrusion recycling plant EREMA for the processing of polyethylene and polypropylene. Capacity of approx. 1,100 kg/h. WITHOUT DEGASSING. Processing of only CLEAN material; without printing ink. Auch Folien + Technik e. Kfm. D-73728 Esslingen Phone +0049 1577 5329827
Replacement blades for cutting machines -Knife size: 205x63x1.47 -Type: 675 FB99261 -Number: 5x available -Price: per piece
Replacement blades for cutting machines -Brand: Stumabo -Blade size: 190x50x5 mm -Type: 2114662 -Number: 162x available -Price: per piece -Minimum order: 3 pieces -Dimensions: 190/50/H5 mm -Weight: 0.27 kg
maximum number of results exceeded
please refine your search
390 € 
