oil production line used for sale

Height=1.57 m, Overall length= 0.82 m, Overall width= 0.82 m, Net weight= 143 kg,

APV pilot UHT plant equipped with an indirect heating module using a plate heat exchanger and an aseptic homogeniser. The unit was previously used for R&D purposes in a dairy plant in Belgium. Capacity up to 400 litres per hour. Temperature profile: approx. 4 – 145 – 20 °C., The skid-mounted unit consists of a plate heat exchanger (APV T4) with 5 sections and a total of 127 plates (9-15-23-55-25), two regeneration sections, heating and cooling sections, hot water/steam section and indirect steam heating. The system is further equipped with three connectable holding tubes, balance tank (Ø 38 cm, height 75 cm, volume approx. 80 litres) with agitator for ingredient mixing, water circulation pump, centrifugal product pump feeding the balance tank and a high-pressure plunger pump (Cat) with variable speed control via frequency inverter. The installation includes all required valves and  ...

Complete cake production line for sale with a finished product capacity of 600 kg/hr. The line includes: • DIOSNA V600B batter mixing system with REIMELT feed pump • COMAS depositing system • MEINKE TURBU 1101 continuous gas tunnel oven • TECNOPOOL FLEX-SPIRAL cooling tunnel • COMAS filling, coating and decoration systems • ILAPAK DELTA 3000 packaging line • LOMA metal detection systems • Additional conveyors, syrup preparation and cake arrangement systems Main manufacturers: DIOSNA, REIMELT, COMAS, MEINKE TURBU, TECNOPOOL, ILAPAK, LOMA Year of manufacture: 2002 / 2003 Condition: Very Good Sold AS IS / WHERE IS. Inspection available by prior appointment. Price upon request.

On behalf of our client, we are requested to offer this Pasta filata cheese line for sale, due to increasing production at the current factory. The whole line is delivered and built up by Sulbana AG Switzerland in 2019 and it is out of production for ± 1 year. The pasta filata cheese line produce products like Mozzarella, Burrata, Kashkaval, Pizza Cheese etc. The capacity of the line is 200 to 800 kg per hour. The line is already dismantled and located in the warehouse of the dairy in Germany, where it can be inspected., The line exist out of the following components:, - Elevator for lifting normcar trolleys of 200 liter with basic ingredients including tipping unit to empty the trolleys inside the feeding bunker. Max load: 350 kg. Manufacturer: Frontmatec Hygiene GmbH, type: Hebe- Und Kippvorrichtung, model: 27000, serial number: P-10259, year: 2019, motor: 0,75 kW - 400 V - 50 Hz., -  ...

Luwa SMS GmbH LN-0200 - Vertical Thin Film Evaporator consist of a cylindrical, vertically-arranged body with heating jacket. A rotor inside the body is equipped with rows of pendulum blades along the full length of the dryer., Special thin-film evaporator designed for dairy service, discharge system, vapor pipe, condenser, and drives. It was in used as a pilot plant on a dairy service until early 2001 and afterwards converted to a 2 square metre cheese base processor with discharge system and ran till 2025 in a Casein plant in a dairy factory in New Zealand., The vertical thin film dryers operate as follows: The wet feed is spread by the pendulum blades in a thin layer onto the heated wall. During this process, the volatile components evaporate continuously out of the product layer at high evaporation rates. The pendulum blades are designed with a minimum gap to the heated wall to preve ...

Koch Membrane Systems (GEA Tuchenhagen computer designed) Ultra Filtration (UF) plant for continuous circulation / concentration / filtration and the production of double cream cheese (philadelphia style). Once the plant is running continuously with ratio control, no manual interventions are generally necessary for the production of the UF concentrate. However, for optimal production of consistent quality, strict adherence to various prerequisites is necessary, e.g. regarding cleaning. Line still located at its original position in the dairy in Austria., The Ultra Filtration line exist out:, - Level tank, 750 liter., - Product feed pump (P1), Tuchenhagen VPB 32 L, 5.000 ltr/h, 39 mWs, motor 3 kW - 2.900 rpm - 380 V - 50 Hz., - Permeate pump (P2), Tuchenhagen VPB 32 L, 5.000 ltr/h, 35 mWs, motor 3 kW - 2.900 rpm - 380 V - 50 Hz., - CIP pump (P3), Tuchenhagen VPD 51, 110.000 ltr/h, 8 mWs,  ...

Unused renovation kit for an Alfa Laval CPM Constant-Pressure Modulating Valve (CPMI-2) pneumatic regulating valve. Genuine Parts Service Kit CPMI - 2/XPMO - 2 Upper NBR, Lower EPDM/PTFE, part no. 9611920218., Type of Machine: Constant-Pressure Modulating Valve, Art. no.: 9611920218

A complete Stürtz window production line is available. 1) Stürtz STBAZ-IPT-4000-V bar processing system for frames, sashes and mullions, year of manufacture: 2004. 2) Stürtz SE HSM-25/26-Compact-Plus four-head welding machine for sashes, year of manufacture: 2006. 3) Stürtz 4MC Motion Control CNC cleaning machine for the sash line, year of manufacture: 2011. 4) Stürtz WST-25-CNC turning station at the sash cleaner (3), year of manufacture: 2011. 5) Stürtz SE-HSM-40/26-Compact-Plus horizontal four-head welding machine for frames, year of manufacture: 2006. 6) Stürtz 2MC Motion Control CNC cleaning machine in the frame line, year of manufacture: 2008. 7) Stürtz WST-30 turning station in the frame line, year of manufacture: 2008. 8) Stürtz SE-BHT-3000 brush lifting table as a stop and transport table before the sash stop, year of manufacture: 2008. 9) Stürtz FBS-1 sash hardware sc ...

The Mac Ewans Centrifugal pump is a pump for use in sanitary applications. Previous used in a Casein plant. Motor: 7,5 kW - 400 V - 50 Hz - 1.460 rpm - 14,3 A. Diameter of the impellor: 180 mm. Connections on the inlet: 3. Connections on the outlet: 2,5. Estimated capacity: ± 30.000 ltr/h., macewans.co.nz/, Type of Machine: Centrifugal pump, Stock Number: 1444, Diameter of the impellor: 180 mm, Motor: 7,5 kW - 400 V - 50 Hz - 1.460 rpm - 14,3 A, Estimated capacity: ± 30 m3/h

Used line for the production of Mazzoni toilet cubes with a capacity of 1000 kg/h. The line includes: – Mixtruder type SZ-1000 – Filtrocyclone – Extruder SX-B-250/HE – Extrusion head. – Slicer – Twin screw conveyor – Year of manufacture 2007.

Margarine pilot plant with 1x high pressure pump, 3x crystalizer scrap surface heat exchangers (SSHE), 1x pin worker (1 - 2 and 3 liter), 1x phase inverter, 1x cooling unit (R22) and control panel. Working product pressure of the pilot plant up to 80 bar (8000 kPa). Capacity up to 90 kg per hour., - High Pressure Pump, High Pressure Pump for pumping the margarine emulsion through the margarine pilot plant. Gerstenberg & Agger A/S, type Labo Pump 2-22-4 , serial number 12.211, year 1990, product pressure max 80 bar, temperature max 100 °C, capacity max 200 kg/h, motor 415 V - 50 Hz - 1,1 kW. Control panel with Siemens S7-200 PLC., - Scraped Surface Heat Exchanger 01, Cooler., Pilot G&A Perfector - SSHE Cooler Perfector 57 is designed for lenient cooling of medium viscosity, pumpable food like margarine. Gerstenberg & Agger A/S, type Perfector Lab 1x57, serial number 12910, year 1993, dut ...

Wood production line manufactured in 2023. This ISM ATM-01 is a custom-made automatic production line designed for the fully automated manufacturing of wooden garden screens from individual planks. It features automatic discharge and stacking of finished screens, tilting stacks for efficient processing, and is adjustable for five different screen types. If you are looking to get high-quality wood processing capabilities, consider the ISM ATM-01 machine we have for sale. Contact us for further details.

Used door panel production - consisting of: Double-End Profiler Brand: Kraft Technical Specifications - 2 scissor lift tables - 2 vacuum grippers - Feed roller conveyor with belt conveyor - New Siemens touch control system 13 roller conveyor sections Brand: Kraft Technical Specifications - Powered, approx. 3000 mm each Continuous Inlay Special inlay line Gantry loader Brand: Kraft Year of manufacture: 2023 Technical specifications - For separating, aligning, and placing HPL Glue applicator Brand: Bürkle Year of manufacture: 1990 Glue applicator Brand: Kuper Year of manufacture: 2018 Laying table Technical data - Work platform for glue tanks, including staircase - Lifting station - motor-driven - Includes PVC conveyor belt Continuous-feed platen press Brand: Bürkle Optima 1428/50 Year of manufacture: 2017 Technical data - Start of series production in 2023 - 2 x 4 levels w ...

Used painting line Bütfering / Belting/ Heesemann / Bürkle / Elmag / Cefla / Venjakob Painting line consisting of: Vacuum feeding system Technical specifications - 2-lane - Roller width: approx. 1000 mm Wide-belt sander Brand: Büftering Type: Classic 213EB Year of manufacture: 2000 Technical specifications - Working width: max. 1350 mm - Vacuum feed belt - Electronic sanding shoe Belt conveyor system Brand: Belting Year of manufacture: 2019 Technical specifications - Dimensions: 6100 x 1000 mm Dust extraction system Brand: Heesemann Type: EA2 Year of manufacture: 1990 Coating machine Brand: Bürkle Type: DAL1-1300 Year of manufacture: 1993 Continuous drying tunnel Brand: Bürkle Technical specifications - With UV lamp Coating machine Brand: Bürkle Type: DAL1-1300 Year of manufacture: 1993 UV drying tunnel Brand: Elmag Type: Ti166-35+2iVM1-65 Technical specifications - Eq ...

wire diameter 2,4-4 mm spring diameter 42-55 mm output - pieces/min ca. 32 m

The ITT Jabsco Pureflo Lobe 24250-4310 is a positive displacement rotary lobe pump with sanitary design which can handle dairy products (e.g., yoghurt, quark, curd and butter), foodprocessing, beverage, cosmetics, pharmaceutical and fine chemicals industries. This pump is perfect for managing all kinds of fluid, of either low or high viscosity, as well as for filtering and bottling applications. Products containing fragile solids such as curd can be pumped without damage thanks to the specially designed lobes. Tri-lobe stainless steel lobes / rotors. Nominal displacement: 0,936 liter per revolution. Maximum nominal capacity: 39,9 m3/h. Inlet connection: 3 RJT. Outlet connection: 3 RJT. Maximum product pressure: 6 bar Maximum pump speed: 700 rpm. Maximum temperature: 110 °C. Previous used in a Casein plant. The current motor with this pump is 7,5 kW - 1.450 rpm - 400 V - 50 Hz - 14,3 A.  ...

Wood production line manufactured in 2020. This HYMMEN JUPITER JPT C 680/548 mit OFS 850 features a maximum printing width of 548 mm, with a system speed ranging from 8 to 65 m/min. It is designed for high-speed surface finishing of large panels, ideal for the flooring and furniture industries. If you are looking to get high-quality printing capabilities, consider the HYMMEN JUPITER JPT C 680/548 mit OFS 850 machine we have for sale. Contact us for further details.

Line is consisting of:, Weber slicer, Type: CCS904, Serial number: 7096, Year of construction: 2007, Capacity: 2000 RPM, Slice thickness: 0.5 - 50 mm, Compressed air: 10 Bar, 150 L/min., Power: 3 x 400V, 50Hz, 10 kW, Dimensions: 13400 x 1900 x 2600 mm, Including CCW904 weigher, CCR904 rocker, CCA speedloader and CCU portioning unit, Pago labeler, Type: System 516, Serial number: 212516068, Year of construction: 2012, Mettler Toledo metaldetector and checkweigher, Type: XS3, Serial number: 35000430, Year of construction: 2008, With reject, Bosch Sigpack Systems robot / cartoning line, Type: LDM + TTLi, Serial number: J-01659-LDM-042 / J-01659-TTLi-077, Viewtech optical control, Type: VT2007/010, Serial number: VT2007-DCDCL/057, With reject

, from the manufacturer (built in 2002) are available for sale, each with a . , totaling approx. 3,534 hl. The tanks are insulated, clad and have three frame cooling zones and cone cooling for precise temperature control. Each tank is designed for a maximum overpressure of 2 bar and can be used at operating temperatures of -10 to 50 °C. The total cooling area is 13.3 m². With a robust stainless steel construction and upright positioning, the tanks are ideal for breweries or beverage manufacturers that require temperature-controlled fermentation and storage processes. Individual sale possible. Our team at VBW Asset Trade will be happy to answer your questions., Additional title: vertical, coolable stainless steel tanks, Gross volume: 58890 l, Max. overpressure: 2 bar, Operating temperature: -10 to 50 °C, Total cooling area: 13,3 m², Length: 3370 mm, Width: 3370 mm, Height:  ...

Line is consisting of:, Townsend MasterFormer, Type: TA1521, Serial number: 10080439, Year of construction: 2010, Stork MasterFill, Type: MTFII, Serial number: 0441010, Year of construction: 2010, Stork Master Slice, Type: DRST, Serial number: 0420410, Year of construction: 2010, Caliber: 50 mm, Karl Schnell vacuumfiller, Type: P10SE, 596P, Serial number: 22045, Year of construction: 2010, Power: 3 x 400V, 50Hz, 10.9kW, Weight: 1180 kg, Risco vacuumfiller, Type: RS303, Serial number: T310021, Year of construction: 2010, Power: 3 x 400V, 50Hz, 7.7kW, Weight: 830 kg, With RS70 grinding head

Complete powder plant existing out of Evaporator (4-effect, TVR), Spray Dryer, Fluidbed Dryer, 2x Crystallization Tanks and a Big Bag Filling Station. Previously used for skim milk / whole milk / whey / permeate or 35% protein powder. Still mounted on its original postion inside the factory in Spain. Line per direct available., Infeed capacities evaporator:, - Skim milk: 7.200 kg/h @ 9% TS., - Whole milk: 4.800 kg/h @ 12,5% TS., - Whey: 8.150 kg/h @ 6% TS., - Permeate: 8.835 kg/h @ 4,5% TS., - 35% Protein: 2.880 kg/h @ 10% TS., - Water for startup and CIP: 10.000 ltr/h @ 2 bar., - Water for cooling seals in vacuum pumps: 7.000 ltr/h @ 25 °C - 2 bar, demineralized., - Water for safety / firefighting should be available at 7.000 ltr/h @ 2 bar., - Water for condenser cooling: 30.000 ltr/h @ 28 °C - 2 bar., - Ice water for flash system: 2.000 ltr/h @ 3 °C - 2 bar., - Saturated dry steam:  ...

Wood production line manufactured in 2006. This HUNDEGGER K2-4-450 features a maximum log length at infeed of 13 m and at outfeed of 12 m. The machine includes a fully automatic beam turning station and various cutting and drilling units for versatile operations. If you are looking to get high-quality timber framing capabilities, consider the HUNDEGGER K2-4-450 machine we have for sale. Contact us for further details.

NEW in box, never used, Order number: ON17163, Capacity: max 800 pigs/hr., Products: pork carcasses, left & right, Slaughtered weight: 70 - 120 kg, Air pressure: 6 - 8 Bar, 285 Nl/min., Power: 3 x 400V, 50Hz, 45kW, Dimensions: 10000 x 5150 x 2300 mm

Used Complete Tinplate Can Production Line for Oil (4–20 L) – Overview This second-hand, industrial packaging line is a complete tinplate can production system engineered for 4–20 L oil containers. Configured for body making, end making, compound lining, curing, double seaming, and handle welding, it offers a proven route to scale up edible oil container manufacturing. The line features reputable OEMs such as Soudronic, BIBRA, YAGUCHI, Cevolani, W.R. GRACE, and RKHD, making it a robust choice for companies seeking a used bottling line complement or an integrated container-making solution for food and beverage packaging operations. Year of manufacture: 1976 (body making section built in 1981) Technical Specifications & Performance Data Container Range & Materials Format range: 4 L to 20 L tinplate steel cans for edible oil and related viscous products Body styles: compatible with la ...

Stephan UM/SK 150 Universal Machine for the production of processed cheese, convenience products, vegan spreads and confectionery. The bowl is equiped with a double jacket for heating / cooling on the jacket, 4x direct steam injection nozzles for direct injection of (culinair) steam inside the product, temperature sensor inside the product, 1x cutting blade, maximum working pressure in the bowl -1 / 0,8 bar, maximum temperature in the bowl 110 °C, vacuum connection on the bowl, mounted on the lid a scraper agitator for the wall, electric driven (1,5 kW - n1: 1.410 rpm - n2: 25 rpm), 2 manual tightening clamp,hydralic cylinder for easy opening the lid, tiltable for emptying the bowl (no pneumatic outlet valve). Main motor for the cutting knife, integrated vacuumpump and a stainless steel control panel with Siemens S5 PLC and Siemens operation panel. Several spare parts included., Type of ...

Wolff Turbitherm WUM-120 Universal Machine for the production of processed cheese, convenience products, vegan spreads and confectionery. The bowl is equiped with a double jacket for heating / cooling (maximum pressure 4 bar and maximum temperature 151 °C) , 3x direct steam injection nozzles for direct injection of (culinair) steam inside the product, temperature sensor inside the product, 3x cutting blades, maximum working pressure in the bowl Vacuum / 1 bar (protected with overpressure valve), maximum temperature in the bowl 119 °C, vacuum connection on the bowl, dearation connection on the bowl, mounted on the lid a scraper agitator for the wall, electric driven (1,1 kW - n1: 1.400 rpm - n2: 21 rpm), 5 manual tightening clamps, hydraulic system for tilting the bowl for easy emptying and for easy opening of the lid. Pneumatic outlet valve. Main motor for the cutting knife: 380 V - 50 ...

The Mac Ewans Centrifugal pump is a pump for use in sanitary applications. Previous used in a Casein plant. Motor: 7,5 kW - 400 V - 50 Hz - 1.465 rpm - 13,9 A. Diameter of the impellor: 180 mm. Connections on the inlet: 3. Connections on the outlet: 2,5. Estimated capacity: ± 30.000 ltr/h., macewans.co.nz/, Type of Machine: Centrifugal pump, Stock Number: 1446, Diameter of the impellor: 180 mm, Motor: 7,5 kW - 400 V - 50 Hz - 1.465 rpm - 13,9 A, Estimated capacity: ± 30 m3/h

Tebel OST-IV Closed cheese vat of 8.000 ltr. Double jacketed for injection of steam or hot water so the temperature of the milk inside the vat can be indirectly adjusted. Stirring, cutting tools, welded to a horizontal shaft. This is driven by a drive unit with frequency converter. During cutting the tools rotate in the opposite direction as during stirring. The coagulum is cut by sharp radial knives of stainless steel. Whey can be drawn off through a perforated pipe (whey suction device). This pipe is lowered into the whey until it is only just immersed. The curd is discharged through the bottom valve. The vat is inclined (4%) toward the bottom valve to facilitate emptying. After a production run the vat is cleaned by four rotating CIP nozzles located in the top. All parts are made of stainless steel AISI 304 except the drive unit. Stainless steel MCC panel at the backside, close to the ...

Tebel OST-IV Closed cheese vat of 8.000 ltr. Double jacketed for injection of steam or hot water so the temperature of the milk inside the vat can be indirectly adjusted. Stirring, cutting tools, welded to a horizontal shaft. This is driven by a drive unit with frequency converter. During cutting the tools rotate in the opposite direction as during stirring. The coagulum is cut by sharp radial knives of stainless steel. Whey can be drawn off through a perforated pipe (whey suction device). This pipe is lowered into the whey until it is only just immersed. The curd is discharged through the bottom valve. The vat is inclined (4%) toward the bottom valve to facilitate emptying. After a production run the vat is cleaned by four rotating CIP nozzles located in the top. All parts are made of stainless steel AISI 304 except the drive unit. Stainless steel MCC panel at the backside, close to the ...

Hitec, Z-Elevating conveyor belt., Dimensions in the photo album., More information on request.

QTY. 1 SECOND-HAND PASTA / NOODLE PRODUCTION LINE – FOR SHORT AND LONG PASTA Mfct.: Macri (Italy), Braibanti (Italy); Capacity: approx. 260 kg/h; Built: 1990 & 2000, Status: still on foundation, stopped in 2022 General description: The pasta factory currently works with 2 x 160 Kg/h presses, one for long pasta and one for short pasta. The drying capacity of each dryer is +/- 500 kg. To fill them all it takes +/- 15/16 hours, i.e. two work shifts. Required area: 805 sqm., approximately L x W x H = 35 m x 23 m x 7 m

Gouda Euroblock Cheese Production Line for Sale due to the installation of a larger cheese production line within the existing cheese factory. The plant was designed for a milk intake capacity of approximately 100.000 litres per day, producing around 10.000 kg of Gouda cheese per day. The line manufactures Gouda cheese in Euroblock format, with dimensions of 500 x 300 x approximately 100 mm and an average weight of 15 kg per block. This corresponds to a daily production of approximately 650 Gouda cheese blocks., The production line consists of the following main components:, - 2 x Closed Cheese Vats with Whey Extraction Sieve., Manufacturer: Tetra Pak Tebel, Type: OST IV, Year: 1991, Capacity: 8,000 litres each, Cheese Vat 1:, Stocknumber: #1005, .hamburg-machinery/listings/4811812-used-cheesevat-tebel-tetra-pak-ost -iv, Cheese Vat 2:, Stocknumber: #1006, .hamburg-machinery/listings/4811 ...

Weinig Unicontrol 10 (UC 10) mitre saw system for the manufacture of windows, components and doors. Suitable for frame-by-frame, batch or individual part production, with 2 tenoning and slotting spindles, including an Oertli tool set Units: 1. Cross-cut saw, NC axis, 3 kW, ø 40 mm, 2,800 rpm 2. First tenoning and slotting spindle, NC axis, ø 50 mm, 15 kW, Technical data: Clamping length: 640 mm (8 x 80) mm Condition: Gebraucht Location: Tauberbischofsheim, Germany

This HEESEMANN BÜRKLE wood production line was manufactured in 2001. It features a comprehensive oil application line, including RBO vacuum feeding Tornado SC 1300, HEESEMANN MFA 8 with cross-lengthwise brushes, and BÜRKLE SLC 1400 roller application machines. Enhanced with a new Siemens control system in 2024, consider the opportunity to buy this HEESEMANN BÜRKLE wood production line. Contact us for more information.

Technical details Manufacturer: Schlatter AG Type: Automatic resistance wire mesh welding and production line Configuration: Wire coil pay-off stations, longitudinal wire feeding system, wire straightening units, cross-wire positioning mechanism, multi-electrode resistance welding section, welding transformers, mesh transport system, output stacking section, auxiliary roller handling and tensioning station, relay-based electrical control cabinets, pneumatic and electromechanical actuation systems. Application: Production of welded wire mesh, reinforcement mesh, fence panels, industrial mesh and construction wire products. Function: Automatic feeding of longitudinal and cross wires, resistance welding of wire intersections, mesh transport, tensioning, flattening and stacking of finished panels. Electrical system: Relay logic control architecture with contactors, transformers and te ...

Pilot plant with 3x used Tetra Laval Food - Schroder Kombinator VWK01/60-400 Scraped Surface Heat Exchangers (SSHE) for heating and/or cooling of liquid, viscous, high viscous and crystalline products. 1x used for heating, 1x used for cooling with city water and 1x used for cooling with R22 (Freon). 3x independent motors with mechanical variators for adjusting the speed. Hotwater preparation unit. Stainless steel control panel with relays controls, 3x Ampere meters, Temperature control unit, controls for feedpump and cleaningpump (pumps itself excluded). Cooling compressor (R22 Freon). Power: 380 Volt - 50 Hz - 3 Ph - 31 A. Manual available., Capacity: 20 - 100 kg/h (depending on product / trial specifications), Max. working pressure: Up to 25 bar, Cooling medium: R22 (Freon), Total Power Consumption: 380 Volt - 50 Hz - 3 Ph - 31 A, Dimensions: 240 x 140 x 200 cm, Weight: 1.000 kg

A production line with 3 KUKA KR 150-2 industrial robots for the production and handling of molded parts is offered. Rated payload per robot: 150kg, max. reach: 2700mm, 6 axes, pose repeatability: +/-0.06mm, protection rating: IP65, mounting position: floor/ceiling, axis speeds: A1: 110°/s, A2: 110°/s, A3: 100°/s, A4: 170°/s, A5: 170°/s, A6: 238°/s, motion ranges: A1: +/-185°, A2: 0° to -146°, A3: +155° to -119°, A4: +/-350°, A5: +/-125°, A6: +/-350°. Including peripheral equipment and accessories. Weight per robot without controller: approx. 1245kg. The production line was used, among other applications, for the production of plant containers and is ideally suited for processes involving plastics as well as processed fiber-based bio-residues and residual materials. It is particularly designed for molding, pressing, handling and automation processes. Inspection by arrangeme ...

Adjustable feed station with 5 rollers (1500x600x250) Working width 1200 mm. 22 rolling stations with double horizontal axes. Adjustable guides. Precision bearings per station. Cardan driven rollers Hydraulic power unit (1520x1400x800 mm) with Tatung 22 kW FBDP-HD drive. Hydraulic cutting unit with double punch equipped with Leedan LDSM230D-II 15 kW servo motor. Equipped with hydraulic decoiler (2500x1400x2000 mm, capacity 5000 kg. Including roller conveyor (3000x1020x760 mm) Auction-ID: A1-47358-23

Adjustable feed station with 5 rollers (900x700x360) Working width 630 mm. 12 rolling stations with double horizontal axes. Adjustable guides. Precision bearings per station. Hydraulic power unit (1000x600x1100 mm) with 4 kW drive. Hydraulic cutting unit. 20 kVA Cheng Hsuan transformer. Equipped with decoiler (1300x700x1100 mm) Including roller conveyor (3000x1020x760 mm) Auction-ID: A1-47358-24

Salvagnini automated line for punching and paneling of sheet metal, year 2002, composed of P4-0905, S4-0928 and automatic storage and handling system MV0016. Salvagnini S4-0928: Year: 2002 Serial Number: S4_0928 Order number: COMM. 500480 Electrical connection: 380 V / 50 Hz / 3 phases Rated power: 68 kW Rated current: 121 A Main Switch Breaking Capacity: 40 kA Automatic storage and handling system: Serial Number: SMD_016 Year: 2002 Electrical connection: 380 V / 50 Hz / 3 phases Rated power: 22 kW Rated current: 42 A Main Switch Breaking Capacity: 40 kA Visible reading of the hour meter: approx. 35,204 h. The installation includes an automatic sheet metal storage and handling system, material transfer systems, punching equipment, paneling equipment, control stations and associated components, as shown in the photographs. The line needs approximately one month for  ...

Technical details Type: Phyllo dough production line Configuration: - Dough mixer - Dough feeding hopper - Multi-stage sheeting and calibrating rollers - Conveyor system - Cross-transfer conveyor - Laminating section - Cutting and stacking table - Electrical control cabinets - Variable-speed drive controls - Operator control panels Application: - Continuous production of phyllo (filo/yufka) dough - Industrial bakery production Construction: - Modular processing line - Stainless steel product contact components - Integrated conveyor system Dimensions: - Length: Approx. 18000 mm - Width: Approx. 3000 mm - Height: Approx. 2600 mm Weight: Approx. 7000 kg Condition: Used Observed condition: - Line appears substantially complete - Roller stations and conveyors installed - Electrical cabinets and control panels present - Safety guards fitted on processing sections ...

Technical details Type: Chocolate production line Visible processing module: - Manufacturer: PAND - Model: DZD-100 - Year: 2020 - Installed power: 35 kW - Power supply: 400 V / 50 Hz Configuration: - Chocolate moulding and processing line - Cooling tunnel - Stainless steel conveyor system - Depositing/forming section - Demoulding module (PAND DZD-100) - Electrical control cabinet - HMI touchscreen control system Application: - Chocolate production - Confectionery manufacturing - Continuous food processing Construction: - Hygienic stainless-steel construction - Modular production line - Integrated conveyor system Dimensions: - Length: Approx. 12000 mm - Width: Approx. 1500 mm - Height: Approx. 2200 mm Weight: Approx. 3500 kg Condition: Used Observed condition: - Complete integrated production line - PAND DZD-100 processing module installed - Electrical ca ...

Consisting of: infeed roller conveyor, cross transport belt conveyor, driven feed through roller conveyor, two-sided horizontal multi drill aggregate, 2x Gasco dowel vibratory feeder model BV25, feed through driven roller conveyor, 3x vertical multi drill aggregate, belt feed through conveyor table, 3x vertical multi drill aggregate, driven feed through roller conveyor table, 1x Gasco vibratory feeder model BV45-2R, 5-headed glue deposition unit, belt feed through conveyor table, 2x 3-station drawer slide insert units, 1x Gasco vibratory feeder model BV45-2L, 5-headed glue deposition unit, outfeed driven roller conveyor table, 3x 3-door switch cabinet, control desk with monitor, cameras, safety fence and stairs with walking platform. Used floor space approximately 26.000x7000mm Auction-ID: A1-48377-1

Continuous Butter Making Machine (CBM) which has a production capacity of 1.200 kg butter per hour sweet butter and 1.000 kg butter per hour cultured butter. Input of ± 2.400 liter of cultured or / and sweet cream per hour (35/42% fat, pH of ± 4,8 and infeed temperature ± 8 - 13 °C). Complete electric driven. Speed controlled large volume and long buttering cylinder with double cooling system. Cylindrical buttering drum whose principle is based on thermal friction (patented process) with adjustable, short blow bars. Complete kneading area existing out of extra-long buttermilk separating section with circulation cooling and double buttermilk clarifier (patented), injecting iced buttermilk to intensively cool the butter grain, pressing tunnel in which the buttermilk is literally squeezed out of the butter mass, which ensures the production of butter with a very low water content in ord ...

The Alfa Laval LKH Centrifugal Pump is a premium pump for use in hygienic applications. Designed for Cleaning-in-Place (CIP), the Alfa Laval LKH is ideal for hygienic applications within the dairy, food, beverage and personal care industries that require gentle product treatment and reliable operation. Motor: 4 kW (motortag cannot be read anymore). Diameter of the impellor: 165 mm. Connections on the inlet: SMS 2,5 mm. Connections on the outlet: SMS 2. Current capacity (based on the available Alfa Laval performance curves and the current motor): 22.000 ltr/h @ 3,6 bar., Additional features:, Maximum capacity of the pump with change of motor (based on the available Alfa Laval performance curves): 60.000 ltr/h @ 2,2 Bar., Type of Machine: Sanitary centrifugal pump, Stock Number: 1564, Diameter of the impellor: 165 mm, Motor: 4 kW, Current maximum capacity: 22 m3/h @ 3,6 bar

The Alfa Laval LKH Centrifugal Pump is a premium pump for use in hygienic applications. Designed for Cleaning-in-Place (CIP), the Alfa Laval LKH is ideal for hygienic applications within the dairy, food, beverage and personal care industries that require gentle product treatment and reliable operation. Motor: 5,5 kW - 380/420 V - 50 Hz - 2.910 rpm - 11,2 A. Diameter of the impellor: 165 mm. Connections on the inlet: SMS 2,5 mm. Connections on the outlet: SMS 2. Current capacity (based on the available Alfa Laval performance curves and the current motor): 45.000 ltr/h @ 3,0 bar., Additional features:, Maximum capacity of the pump with change of motor (based on the available Alfa Laval performance curves): 60.000 ltr/h @ 2,2 Bar., Type of Machine: Sanitary centrifugal pump, Stock Number: 1570, Diameter of the impellor: 165 mm, Motor: 5,5 kW - 380/420 V - 50 Hz - 2.910 rpm - 11,2 A, Current ...

with technical advice, Affordable housing Low-cost housing, cmodul austria low cost housing • Pallet circulation systems for filigree and double wall elements NEW & USED • Machines and systems for prefabricated parts - battery formwork, tilting tables and special moulds • Stationary concrete block paving stone and edge stone installations + shapes as NEW • Mobile concrete stone machines + moulds as NEW • Concrete pipe and shaft ring machines and parts thereof • KS - Lime sandstone works • Dry mortar plants and parts thereof • Brickworks and parts thereof our used lines meets after reinstallation by us the Definition RETROFIT

Machinery and equipment for the production of cement, All prices are from Station World and the dismantling and all follow-up costs are to be made by the buyer. VAT is not included in the prices. The contractual agreements for the individual offers must be agreed separately and only apply after the contract has been legally signed. Mistake reserved. All technical details; Measurements, etc., are approximate information and are non-binding for the provider. The technical data are manufacturer or operator information and therefore non-binding for us. Used material is sold to the exclusion of any warranty. We do not accept any liability for used material. Warranty exchange and return are excluded. Customer protection is agreed between the parties. The entire process of dismantling and loading as well as transport is carried out at the buyer's own expense and at the buyer's own e ...

Ladies and gentlemen, we offer: Machinery and equipment for stone production All prices are from Station World and the dismantling and all follow-up costs are to be made by the buyer. VAT is not included in the prices. The contractual agreements for the individual offers must be agreed separately and only apply after the contract has been legally signed. Mistake reserved. All technical details; Measurements, etc., are approximate information and are non-binding for the provider. The technical data are manufacturer or operator information and therefore non-binding for us. Used material is sold to the exclusion of any warranty. We do not accept any liability for used material. Warranty exchange and return are excluded. Customer protection is agreed between the parties. The entire process of dismantling and loading as well as transport is carried out at the buyer's own ex ...