Injection molding machines used for sale (365)

B&A REF:  9314 TON: 420 SCREW DIAMETER:  70MM SHOT WEIGHT:  1090 STROKE VOLUME:  1212CM3 INJECTION PRESSURE:  1877AR PLATEN SIZES:  1200 X 1100MM DBTB: 810 X 710MM MIN MOULD HEIGHT:  380MM MAX MOULD HEIGHT: 820MM MOULD OPENING STROKE:  710MM MAX DAYLIGHT:  1530MM EJECTOR STROKE:  230MM CONTROLS:  NC4 CORE PULLING: 2 AIR VALVES: 3 MOTOR: 45 HEATING CAPACITY: 27KW ROBOT INTERFACE: EUROMAP SCREW DRIVE:   HYDRAULIC

Ref. no.: 18597Hersteller: ENGELYear of construction: 2007Clamping unitClamping force: 70 tonOpening stroke: 305 mmInjection unitScrew diameter: 25 mmInjection volume: 69 cm³Shot weight: 62 gInjection pressure: 2381 barMeasurements and weightDimensions: 4,0 x 1,8 x 2,5 mMachine weight: 5600 kg

B&A REF:  9311 TON: 260 SCREW DIAMETER:  55MM SHOT WEIGHT: 605 STROKE VOLUME:  642CM3 INJECTION PRESSURE:  1460AR PLATEN SIZES:  960 X 960MM DBTB: 650 X 650MM MIN MOULD HEIGHT:  200MM MAX MOULD HEIGHT: 750MM MOULD OPENING STROKE:  650MM MAX DAYLIGHT:  1400MM EJECTOR STROKE:  225MM CONTROLS:  CM10 CORE PULLING: 1 AIR VALVES: 1 MOTOR: SERVO 22  HEATING CAPACITY: 14KW ROBOT INTERFACE: EUROMAP 67 SCREW DRIVE:  HYDRAULIC

Ref. no.: 18501Hersteller: ENGELYear of construction: 2008Clamping unitClamping force: 380 tonDistance between tie bars: 780 X 780 mmMould height min.: 380 mmMould height max.: 750 mmPlaten size (h x v): 1100 x 1100 mmInjection unitScrew diameter: 50 mmInjection volume: 316 cm³Shot weight: 285 gInjection pressure: 2430 barMeasurements and weightDimensions: 7.75 x 2.3 x 2.5 mMachine weight: 19000 kgAdditional information & extrasCore pull: 2 pcs

B&A REF:  9302 TON: 270 SCREW DIAMETER:  55MM SHOT WEIGHT: 594 STROKE VOLUME:  653CM3 INJECTION PRESSURE:  2041AR PLATEN SIZES: 940 X 940MM DBTB: 630 X 630MM MIN MOULD HEIGHT:  250MM MAX MOULD HEIGHT: 650MM MOULD OPENING STROKE:  600MM MAX DAYLIGHT:  1250MM EJECTOR STROKE:  200MM CONTROLS: UNILOG B4 CORE PULLING: 2 AIR VALVES: 1 MOTOR: 30 HEATING CAPACITY:  18.2KW ROBOT INTERFACE: EUROMAP 67 SCREW DRIVE:   HYDRAULIC

Ref. no.: 18588Hersteller: BATTENFELDYear of construction: 2007Clamping unitClamping force: 30 tonDistance between tie bars: 300 x 300 mmMould height min.: 150 mmMould height max.: 330 mmOpening width: 580 mmPlaten size (h x v): 450 x 450 mmInjection unitScrew diameter: 18 mmInjection volume: 19 cm³Shot weight: 17,5 gInjection pressure: 2500 barMeasurements and weightDimensions: 3,5 x 1,1 x 1,9 mMachine weight: 2700 kg

B&A REF:  9307 TON: 1100 SCREW DIAMETER:  105MM SHOT WEIGHT: 3075 STROKE VOLUME:  3380CM3 INJECTION PRESSURE: 1600AR PLATEN SIZES:  1850 X 1810MM DBTB: 1400 X 1150MM MIN MOULD HEIGHT:  600MM MAX MOULD HEIGHT: 1200MM MOULD OPENING STROKE:  1800MM MAX DAYLIGHT:  2400MM EJECTOR STROKE:  300MM CONTROLS: CC 200 TOUCH CORE PULLING: 4 AIR VALVES: 2 MOTOR: 75 HEATING CAPACITY: 72KW ROBOT INTERFACE: EUROMAP 67 SCREW DRIVE:   HYDRAULIC

Ref. no.: 17540Hersteller: ARBURGYear of construction: 1994Clamping unitClamping force: 50 tonOpening stroke: 350 mmDistance between tie bars: 270 X 270 mmMould height min.: 200 mmPlaten size (h x v): 405 X405 mmInjection unitScrew diameter: 25 mmInjection volume: 67 cm³Shot weight: 61 gInjection pressure: 2500 barMeasurements and weightDimensions: 3,3 X 1,5 X 2,0 mMachine weight: 2400 kg

Key data: 6500 kN, 80 mm

Clamping force: 650t Year of construction: 2024 Injection Unit .../4630 Screw diameter 80 mm Spec. Spray pressure 2090 bar Injection volume 2212 cc Hydr. Drive power 113 kW L/D Screw Ratio 22 Clamping Unit 6500/... Clamping force 650 t Lights spar spacing 1040 x 910 mm Ejector force 110 kN Tool installation height 400 mm Opening way 950 mm Max. panel spacing 1350 mm Ejector path 250 mm Weight 27000 kg Year of construction 2024 Control type KEBA 2985 Clamping unit Two-plate technology – hydraulic clamping force Fast tool movement due to two diagonal cylinders Tool protection function Linear guide for BWAP (MAIII PLUS, MA-F) Set of spray nozzles Closing and opening of the mold (max. 5 stages, min. 3 stages) Tool height limitation via limit sensor Clamping plates according to Euromap standard Ejector reset function Display of ejector ...

Ref. no.: 18587Hersteller: FERROMATIK MILACRONYear of construction: 2001Clamping unitClamping force: 200 tonOpening stroke: 750 mmDistance between tie bars: 560 x 560 mmMould height min.: 300 mmOpening width: 1050 mmPlaten size (h x v): 830 x 830 mmInjection unitScrew diameter: 50 mmInjection volume: 416 cm³Shot weight: 375 gMeasurements and weightDimensions: 6,9 x 2,0 x 2,6 mMachine weight: 13000 kg

Key data: 2400 kN, 594 g/PS, 55 mm

Injection Unit .../1330 Screw diameter 55 mm Spec. Spray pressure 2041 bar Injection volume 653 cc Injection weight in hp 594 g L/D Screw Ratio 22 Clamping unit 240/... Clamping force 240 t Size of the clamping plates 910 x 930 mm Lights spar spacing 630 x 570 mm Ejector force 59 kN Tool installation height 350 mm Opening way 725 mm Max. panel spacing 1075 mm Ejector path 200 mm Weight 10000 kg Dimensions(m) LxWxH 5.5 x 1.8 x 2.4 m Year of construction 2013 Control type Unilog B6

Ref. no.: 18494Hersteller: ENGELYear of construction: 2013Clamping unitClamping force: 50 tonOpening stroke: 400 mmMould height min.: 200 mmOpening width: 600 mmPlaten size (h x v): 500 X 450 mmInjection unitScrew diameter: 25 mmInjection volume: 69 cm³Shot weight: 62 gInjection pressure: 2400 barMeasurements and weightDimensions: 3,4 x 1,3 x 1,8 mMachine weight: 2900 kgAdditional information & extrasCore pull: 1 pcs

Key data: 2000 kN, 55 mm

Clamping force: 200t Year of Make: 2002 Injection Unit .../675 Screw diameter 55 mm Spec. Spray pressure 2080 bar Injection volume 427 cc Clamping unit 2000/... Clamping force 200 t Size of the clamping plates 950 x 950 mm Lights spar spacing 570 x 570 mm Tool installation height 300 mm Opening way 650 mm Max. panel spacing 950 mm Year of construction 2002 Control type Selogica

Ref. no.: 18643Hersteller: ARBURGYear of construction: 2008Clamping unitClamping force: 150 tonOpening stroke: 500 mmDistance between tie bars: 470 x 470 mmMould height min.: 250 mmOpening width: 750 mmInjection unitScrew diameter: 35 mmInjection volume: 154 cm³Shot weight: 141 gInjection pressure: 2500 barMeasurements and weightMachine weight: 4850 kgDimensions LxWxH part 1: 4,6 x 1,6 x 2,1 mAdditional information & extrasCore pull: 1 pcsFurther information:Communication card for ProSeS interface is available (OPC-UA).Robot interface is available (EUROMAP 67).

Key data: 1750 kN, 393 g/PS, 50 mm

Clamping force: 175t Year of Make: 2005 Injection weight in hp: 393g Injection Unit .../1000 Screw diameter 50 mm Spec. Spray pressure 2304 bar Injection volume 432 cc Injection weight in hp 393 g L/D Screw Ratio 22 Clamping unit 175/... Clamping force 175 t Size of the clamping plates 915 x 910 mm Lights spar spacing 560 x 560 mm Tool installation height 350 mm Opening way 700 mm Max. panel spacing 1050 mm Ejector path 200 mm Weight 9000 kg Dimensions(m) LxWxH 5.2 x 1.75 x 2.2 m Year of construction 2005 Control type MC4

Injection moulding machine for food and beverages caps

Key data: 600 kN, 94 g/PS, 30 mm

Clamping force: 60t Year of Make: 2001 Injection weight in hp: 94g Injection Unit .../200 Screw diameter 30 mm Spec. Spray pressure 1995 bar Injection volume 106 cc Injection weight in hp 94 g L/D Screw Ratio 20 Clamping unit 600/... Clamping force 60 t Size of the clamping plates 600 x 600 mm Lights spar spacing 420 x 420 mm Tool installation height 200 mm Opening way 550 mm Max. panel spacing 750 mm Weight 3950 kg Dimensions(m) LxWxH 4.2 x 1.4 x 2.0 m Year of construction 2001 Control type NC4

Clamping Force: 300 ton // Shot Weight (Max): 476 g

Key data: 600 kN, 94 g/PS, 30 mm

Clamping force: 60t Year of Make: 2001 Injection weight in hp: 94g Injection Unit .../200 Screw diameter 30 mm Spec. Spray pressure 1995 bar Injection volume 106 cc Injection weight in hp 94 g L/D Screw Ratio 20 Clamping unit 600/... Clamping force 60 t Size of the clamping plates 600 x 600 mm Lights spar spacing 420 x 420 mm Tool installation height 200 mm Opening way 550 mm Max. panel spacing 750 mm Weight 3950 kg Dimensions(m) LxWxH 4.2 x 1.4 x 2.0 m Year of construction 2001 Control type NC4

Clamping Force: 150 ton // Mould Height (Max): 730 mm

Key data: 600 kN, 25 mm

Clamping force: 60t Year of Make: 2001 Injection Unit .../100 Screw diameter 25 mm Spec. Spray pressure 2240 bar Injection volume 49 cc Clamping unit 600/... Clamping force 60 t Size of the clamping plates 446 x 446 mm Lights spar spacing 320 x 320 mm Tool installation height 200 mm Opening way 350 mm Max. panel spacing 550 mm Weight 2440 kg Dimensions(m) LxWxH 3.6 x 1.6 x 2.2 m Year of construction 2001 Control type Selogica

Clamping Force: 200 ton

Key data: 589 kN, 25 mm

Clamping force: 60t Year of Make: 2001 Injection Unit .../100 Screw diameter: 25 mm Spec. Spray pressure: 2240 bar Spray volume: 49 cc Clamping unit 600/... Clamping force: 60 t Size of the clamping plates: 446 x 446 mm Clearance spar spacing: 320 x 320 mm Tool installation height: 200 mm Opening travel: 350 mm Max. plate spacing: 550 mm Weight: 2440 kg Dimensions(m) LxWxH: 3.6 x 1.6 x 2.2 m Year of Make: 2001 Control type Selogica

Clamping Force: 350 ton // Shot Weight (Max): 694 g

Key data: 6 kN, 2582 g/PS, 90 mm

Tederic NEO H680-i4800 – Two-platen injection molding machine Exhibition piece with minimal operating hours – excellently equipped! This machine is a former pilot plant and demonstration device that was used exclusively for demonstration and test purposes. Accordingly, the The machine has hardly any operating hours and is in excellent condition. The extensive equipment goes far beyond the standard. --- Technical data - Clamping force: 680 t (6,669 kN) - Year of construction: 2022 - Injection unit: i4800 - Screw diameter: 90 mm - Injection weight (hp): 2,582 g - Injection volume: 2,837 cc - Spec. Spray pressure: 1,615 bar - L/D Ratio: 20.8 - Clamping plates: 1,500 x 1,400 mm - Handlebar spacing: 1,100 x 960 mm - Ejector force: 182 kN - Tool installation height: 450 mm - Opening travel: 1,400 mm - Max. panel spacing: 1,850 mm  ...

Injection moulding machine for food and beverages caps

B&A REF: 9259 TON: 370 SCREW DIAMETER: 70MM SHOT WEIGHT: 1060 STROKE VOLUME: 1175CM3 INJECTION PRESSURE: 1700AR PLATEN SIZES: 1070 X 990MM DBTB: 710 X 630MM MIN MOULD HEIGHT: 300MM MAX MOULD HEIGHT: 750MM MOULD OPENING STROKE: 710MM MAX DAYLIGHT: 1460MM EJECTOR STROKE: 275MM CONTROLS: DIMI EL2 PLUS CORE PULLING: 2 AIR VALVES: 1 MOTOR: 37 HEATING CAPACITY: 27KW ROBOT INTERFACE: EUROMAP SCREW DRIVE: HYDRAULIC

Clamping Force: 420 ton // Shot Weight (Max): 1555 g

B&A REF: 9289 TON: 320 SCREW DIAMETER: 60-35-30MM SHOT WEIGHT: 607H / 132P / 97S STROKE VOLUME: 644 / 144 / 106CM3 INJECTION PRESSURE: 2000 / 2000 / 2500 AR PLATEN SIZES: 1040 X 1040MM DBTB: 720 X 720MM MIN MOULD HEIGHT: 300MM MAX MOULD HEIGHT: 700MM MOULD OPENING STROKE: 700MM MAX DAYLIGHT: 1400MM EJECTOR STROKE: 250MM CONTROLS: SELOCIA TOUCH CORE PULLING: 3 AIR VALVES: 2 MOTOR: SERVO HEATING CAPACITY: 22 + 7.7 + 7.7KW ROBOT INTERFACE: EUROMAP 67 ROBOT: MULTILFT SELECT 15KG QUER SCREW DRIVE: ELECTRIC HOT RUNNER: 18 ZONE ACCYMULAQTED: 6

Clamping Force: 1000 ton // Shot Weight (Max): 6995 g

B&A REF: 9235 TON: 320 SCREW DIAMETER: 55MM SHOT WEIGHT: 434 STROKE VOLUME: 474CM3 INJECTION PRESSURE: 1650AR PLATEN SIZES: 1040 X 1040MM DBTB: 720 X 720MM MIN MOULD HEIGHT: 300MM MAX MOULD HEIGHT: 800MM MOULD OPENING STROKE: 600MM MAX DAYLIGHT: 1400MM EJECTOR STROKE: 250MM CONTROLS: SELOGICA TOUCH CORE PULLING: 1 AIR VALVES: 1 MOTOR: ALL SERVO DRIVES SCREW DRIVE: ELECTRIC

Clamping Force: 220 ton // Shot Weight (Max): 625 g

B&A REF: 9265 TON: 220 SCREW DIAMETER: 55MM SHOT WEIGHT: 523 STROKE VOLUME: 575CM3 INJECTION PRESSURE: 1550AR PLATEN SIZES: 770 X 770MM DBTB: 510 X 510MM MIN MOULD HEIGHT: 210MM MAX MOULD HEIGHT: 630MM MOULD OPENING STROKE: 550MM MAX DAYLIGHT: 1180MM EJECTOR STROKE: 190MM CONTROLS: E-ONE CORE PULLING: 1 AIR VALVES: 1 MOTOR: 30 HEATING CAPACITY: 14.6KW SCREW DRIVE: HYDRAULIC

Ref. no.: 18565Hersteller: DEMAGYear of construction: 2005Clamping unitClamping force: 150 tonOpening stroke: 500 mmDistance between tie bars: 500 x 500 mmMould height min.: 250 mmOpening width: 750 mmPlaten size (h x v): 750 x 750 mmInjection unitScrew diameter: 45 mmInjection volume: 323 cm³Shot weight: 290 gInjection pressure: 1973 barMeasurements and weightDimensions: 5.45 x 1.63 x 2.1 mMachine weight: 7500 kgRobotProducer: Wittmann Type: W721-0231 Year: 2005

B&A REF: 9275 TON: 200 SCREW DIAMETER: 55MM SHOT WEIGHT: 451 STROKE VOLUME: 475CM3 INJECTION PRESSURE: 1741AR PLATEN SIZES: 780 X 780MM DBTB: 530 X 530MM MIN MOULD HEIGHT: 200MM MAX MOULD HEIGHT: 500MM MOULD OPENING STROKE: 440MM MAX DAYLIGHT: 940MM EJECTOR STROKE: 130MM CONTROLS: VPC 20000E AIR VALVES: 1 HEATING CAPACITY: 12.9KW

Ref. no.: 18586Hersteller: KRAUSS MAFFEIYear of construction: 2011Clamping unitClamping force: 180 tonOpening stroke: 450 mmDistance between tie bars: 560 x 510 mmMould height min.: 200 mmMould height max.: 600 mmOpening width: 1050 mmPlaten size (h x v): 790 x 740 mmInjection unitScrew diameter: 50 mmInjection volume: 393 cm³Shot weight: 357 gInjection pressure: 1892 barMeasurements and weightDimensions: 6,10 x 1,90 x 2,10 mMachine weight: 8400 kgRobotProducer: Krauss Maffei Type: LRX-100 Year: 2012

B&A REF: 9253 TON: 55 SCREW DIAMETER: 32MM SHOT WEIGHT: 92.3 STROKE VOLUME: 96.5CM3 INJECTION PRESSURE: 2127AR PLATEN SIZES: 565 X 540MM DBTB: 360 X 335 MM MIN MOULD HEIGHT: 250MM MOULD OPENING STROKE: 400MM MAX DAYLIGHT: 650MM EJECTOR STROKE: 80MM CONTROLS: ALPHA MOTOR: 11 SERVO HEATING CAPACITY: 7.7KW

Ref. no.: 18142Hersteller: DEMAGYear of construction: 1997Clamping unitClamping force: 50 tonOpening stroke: 400 mmDistance between tie bars: 355 x 355 mmMould height min.: 210 mmPlaten size (h x v): 540 x 540 mmInjection unitScrew diameter: 35 mmInjection volume: 106 cm³Shot weight: 95 gInjection pressure: 2573 barMeasurements and weightDimensions: 3,65 x 1,15 x 1,18 mMachine weight: 3600-2500 kg

Screw diameter: 45 mm Injectable volume / Shot volume: 358 cm3 Injection Pressure: 2426 bar Column passage / Bettween tie bar: 720 x 720 mm Thickness of the mould mini /Mold tickness -max: 320 - 725 mm Opening stroke: 730 mm Euromap 12 4 hydraulic cores - 4 corepulling

screw size: 133 mminjection shot weight in Polysterol: 5940 g/PSclosing pressure: 8000 kNtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Screw diameter: 70 mm Injectable volume Shot volume: 5598 cm3 Injection pressure : 1137 bar Column pass-through: 1060 x 1060 mm Moulded thickness / Mold tickness mini -max: 350 - 1100 mm Opening stroke: 1150 mm Euromap 12 4 hydraulic cores - 4 cOREPULLING

screw size: 115 mminjection shot weight in Polysterol: 3915 g/PSclosing pressure: 6600 kNtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Screw diameter: 120 mm Injectable volume / Shot volume: 5598 cm3 Injection pressure : 1137 bar Column passage / Bettween tie bar: 1060 x 1060 mm Mould thickness mini-maxi / Mould tickness mini-max: 350 - 1100 mm Opening stroke: 1150 mm Euromap 12 4 Hydraulic Cores / 4 Corepulling

Key data: 1300 kN, 475 g/PS, 55 mm

Technical data: Clamping force: 130 t Year of Make: 2008 Shot weight: 475.9 g Injection unit: 1000 Screw diameter: 55 mm Specific injection pressure: 1904 bar Displacement: 523 cc Clamping platens (dimensions): 745 x 745 mm Clear width (spar dimension): 470 x 470 mm Ejector force: 22.6 kN Tool installation height (min.): 300 mm Opening travel: 600 mm Max. panel spacing: 900 mm Weight: 8000 kg Control: MC5

Type: MA16000/15800 Monitor: KEBA V3 Year : 2011 Screw diameter: 140 mm Shot volume: 9683 cm3 Injection weight : 8825 g Bettween tie bar HxV: 1550 X 1430 mm Maxi Mold Height: 1500 mm Min Mold Height: 700 mm Ejector stroke: 400 mm Total Clamp Open daylight: 3100mm 4 corepulling 4 Cascade Injection

Screw diameter: 70 mm Injectable volume: 1078 cm3 Injectable weight: 981 g Injection pressure: 1877 bar Column passage: 630 x 630 mm Opening stroke: 820 mm 8 Zone Heater 3 Hydraulic Cores Robot interface

Key data: 4000 , 1464 , 80

Screw diameter: 80 mm Injectable volume: 1678 cm3 Injectable weight: 1464 g Injection pressure: 1856 bar Column passage: 800 x 800 mm Opening stroke: 1020 mm

Key data: 500 kN

ARBURG ALLROUNDER CENTEX 320 C 500 – 250 (Year 2002) Serial number: 188161 – Machine no. 30 Clamping force: 500 kN Distance between tie bars: 320 x 320 mm Platen dimensions: 446 x 446 mm Injection unit (EUROMAP): 250 Approx. shot volume: 106 cm³ Shot weight (PS): 97 g Operating voltage: 400 V – 3 Ph – 50 Hz Heating capacity: 6.5 kW Pump motor: 1 x 15.00 kW Total connected load: 21.5 kW Machine weight: 2330 kg

Key data: 1000 kN

ARBURG ALLROUNDER SELECTA 470 S 1000 – 675 (Year 2001) Serial number: 187132 – Machine 8 Clamping force: 1000 kN Distance between tie bars: 470 x 470 mm Platen size: 637 x 637 mm Max. mould height: 750 mm Ejector force: 40 kN Ejector stroke: 175 mm Shot volume: 675 cm³ Operating voltage: 400 V – 3 Ph – 50 Hz Heating capacity: 14.9 kW Pump motor: 1 x 22.00 kW Total connected load: 36.9 kW Dimensions: 4180 x 1645 x h, 2140 mm. Machine weight: 5400 kg