hegla gmbh co used for sale

A screw compressor is offered. Maximum pressure 10bar, volume flow approx. 2020l/min (2.02m3/min) with separate compressed air tank, galvanized. Viewing possible by appointment.

- Producer Costa - Working width 1.300 mm - Year of construction 2003 - Working height ~ 850 - 950 mm - 1. Unit - Spindle with brush head, D 180 mm - grain size P180 - Driving speed infinitely adjustable U/min - Motor power 0,75 kW - Spannungsschwankungen max. +/- 5 %

- Producer Venjakob - Type VEN SPRAY Compact - Year of construction 2007 - Working width 800mm (1000) mm - Operating side, left - Duo gun drive system - Dry filter system - Exhaust air 7.000 m³/h - Transport belttransport System - Feed speed adjustable 3 - 8 m/min - Lacquer reclaiming system with v-belt - Gun control system Siemens HMI Panel, new in 2023 - Number of installed lacquer circles 2 Stk. - Number of installed spraying guns 4 Stk. - Number of lacquer pumps 1 Stk. - Producer lacquer pump Kremlin - Supply air box - Switch cabinet built into the machine - Voltage / HZ 400 / 50 - Location, not on stock

A small compressor system including separator, dryer and tank is available. 1) Compressed air receiver MetaCon, year of manufacture: 1994, nominal volume: 1000l, operating temperature range: -10°C/50°C, max. operating overpressure: 11bar. 2) Compressor Atlas Copco GA 18, year of manufacture: 1994, air volume flow: 36.4l/s, max. operating pressure: 10bar, motor power: 18.5kW, speed: 1500rpm. 3) Air dryer Schneider Druckluft GmbH DK 3000 N, max. inlet temperature: 50°C, max. operating pressure: 16bar, refrigerant: R134a, refrigerant charge: 700g, operating overpressure: 17bar. 4) Oil-water separator Donaldson Ultrasep Plus 30, max. residual oil content: 10mg/l, max. compressor capacity: 30m³/min, oil adsorption capacity: 25l, machine dimensions X/Y/Z: approx. 900mm/1000mm/400mm, weight: approx. 70kg. An on-site inspection is possible.

• For film coating (air) and sugar coating (airless) of tablets/microtablets • Drum capacity 10 litres, batch size approx. 5-10 litres • Drum made of stainless steel 1.4401 (AISI 316), without perforation, drum diam. 600 mm, mouth opening diam. 210 mm • 2 guide vanes on centre axis, 6 guide vanes on drum edge • Control unit for dosing (film/sugar) • Dust filter cabinet for inlet and outlet • Drive for 1 peristaltic pump (without peristaltic pump housing) • 1 spray gun GS for film coating, without holder • Dot matrix printer • Without inlet and outlet air system (fans) • PLC Siemens S5-100U • Drive 400V/50Hz • Only 218 operating hours This machine is offered at a special price and sold as-is without technical inspection.

UTECO EMERALD C.I. Gesrless, 8 colors, Max printing width 1.000 mm, quick sleeva change on anilox and printing sleeves, automatic washing, longitudinal register with drive/ motorised, trasversal register, viscometers, Video camera, Web guide, automatic unwinder, 1.000 mm max Ø, automatic rewinder, 1.000 mm max Ø, computer suvervision of the machine, Connected and testable, availability: immediate, working width: 1.000 mm.

Briquette press Compacto 1100 SH with filter house 100 filter Filter length 3 m Filter diameter 15 cm Filter area 142 sqm Air flow rate of approx. 21,000 m3/h Throughput capacity approx. 100 kg/h

General SKU441W1456 LocationBarneveld CEcheck MakeTool-temp Main Features Heating (medium)Electric Capacity24 KW Temp.140 °C Specified Features - Temperature control unit Temperating machinecheck Water heatercheck Temperature+140°C With pumpcheck Capacity110 l/min Motor1,8 kW, 380 volt With temperature controllercheck Information TypeTT-138 N-B4 Mach.No.321-3416-4 Year of construction2021 Mounted on wheelscheck With switchcheck With switchgearcheck Floorspace1,240x0,480 m Total height1,40 m Weight220 kgTemperature control unitsTool-tempHeat exchangers > Temperature control unitsBrand > Tool-temp What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many m ...

3 controllers + 4 industrial screens, Product control + …, Electronics GmbH, used Used! - comes from a spare parts warehouse of a certified production facility, - The parts were removed from die casting machines. Measuring system controls: 3 used measuring system controls from company Electronics, Type: Product control S/N: 0513 4 pcs used industrial screens for the measuring systems At a special price of €500 for all 7 devices without warranty

Cold storage tank 150HL Vertical cylindrical stainless steel vessel. Located out doors with external cladding and insulation finished in riveted stainless steel . Fitted with cooling jackets. Mounted on 4 stainless steel legs with adjustable feet Approx dimensions : Overall height 5000mm Overall diameter 2000mm Legs 800mm Capacity 150HL Second Hand This is a SECOND HAND item and is sold as seen For more information and more available stock please visit us at - advancedbrewing.co.uk

General SKU213X072 LocationBarneveld MakeHosokawa Nautamix NV Haarlem (NL) Pressure Working pressure jacket0.5 Bar Main Features MaterialStainless steel Volume300 Ltr. Motor1.5 KW Specified Features - Conical mixer Conical mixercheck Capacity300 l. Largest cone diameter1200 mm Cone height1600 mm Dished topcheck Top drivecheck Motor1,5 kW, 230/400 volt, 1459 rpm Motorca. 0,4 kW Cantilevered screwcheck With jacketcheck Bottom dischargeDia. 270 mm MaterialStainless steel 1.4301 (304) Information TypeDBX-300 No.M18123 With switchgearcheck Floor space1,40x1,40 m Total height2,40 m Weight800 kgConical mixersHosokawa NautaMixers > Conical mixersBrand > Hosokawa Nauta What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in  ...

Technical data: - Operating hours 4248 h - Load hours 1978 h - Operating pressure 10 bar - Delivery rate 3.34 m³/min - Drive 400 V / 22 kW - Motor speed 3000 rpm - Space requirement approx. W 1300 x H 1250 x D 800 mm - Weight approx. 490 kg

General SKU244X191 MakeKöllemann TypeDT KSF 2XDN300 5500 lg No.0603120/2081250/01 Mach.No.0603120/2081250/01 Year of construction2006 Pressure Working pressure jacket3 Bar Technical specs Max. temperature550 °C Main Features MaterialMild steel Motor1.1 KW Length5500 mm Inlet diameter350 mm Specified Features - Horizontal screw conveyor MaterialMild steel Horizontal conveyor screwcheck Trough-typecheck Double shaftcheck Diameter2x 300 mm Length5500 mm Between inlet and outlet4950mm Shaft diameter140mm Pitch150mm InletDia. 200 and 350 mm Outlet400x150 mm With jacketcheck Max. temperature35°C Motor1,1 kW, 220-240/380-415 volt, 1400 rpm Screw speed2,0 rpm Information LocationBarneveld Floorspace8,0x1,10 m Total height2,0 m Weight2800kg CEcheck Extra Specificationsthe screw is coolableHorizontal screw conveyorsKollemanConveying systems > Horizontal sc ...

Comaca 225 x 3 mm (fixed angle) Capacity : 225 x 3 mm Strokes/min: 80 str/min Fixed angle -- variable angle: fixed angled Workspace: 1050 x 700 mm Electric motor (power): 1,5 kW

Technical data: - Operating hours 20256 h - Operating pressure 13 bar - Delivery rate 4.09 m³/min - Drive 400 V / 26 kW - Motor speed 3000 rpm - Space requirement approx. W 900 x H 1750 x D 900 mm - Weight approx. 490 kg

1 gebr. Kantenbearbeitungsstraße IMA COMBIMA / K/ II/ R75 / 1075 / V / R3 Bj. 1996 Bestehend aus: - Doppelseitige IMA COMBIMA für die Längsbearbeitung: Doppelzerspaner 2 x Fräsen Verleimteil mit Granulat-Vorschmelzer 6-fach Rollen-Magazin für das Kantenmaterial 1 x Hauptandruck- und 4 x Nachpressrolle Kappaggregat Bündfräsen 2 x Feinfräsen Profilziehklinge Flächenziehklinge Schwabbelaggregat Glätteaggregat - Drehvorrichtung von läng auf quer - Doppelseitige IMA COMBIMA für Querbearbeitung Schutzfräsen Doppelzerspannen Nutfräsaggregat Verleimteil mit Granulat-Vorschmelzer 6-fach Rollen-Magazin für das Kantenmaterial 1 x Hauptandruck- und 4 x Nachpressrolle Kappen am Oberdruck (Nachrüstung auf aktuelles Modell) Bündigfräsen Feinfräsen 2 x MFA Fräsen Nutfräsaggregat Profilziehklinge Flächenziehklinge Kopierschwabbeln (4 Moto ...

Operating hours 58730 h Technical data: Max. compressed air: 14 bar Ambient temperature, max.: 50°C Refrigerant: R410A, 0.86 kg Connection: 230 V Weight, approx.: 154 kg

OK-Corp Superformer Sf1 Carton Erector + Inline Superliner SL220-PFF with integrated Carton Erector/ Bottom Flap folder & adhesive tape Bottom flap sealer, Carton top Flap Openner & PE Film Carton Liner from a Roll of Film Full Stainless Steel Construction, Automatically Erects Cartons, tapes the bottom, Lines the Cartons with film from a Roll., Carton Sizes: L x W x H, 250 mm x 200 mm x 150 mm (min), 600 mm x 475 mm x 600 mm (max) Speeds upto 15 Cartons per/ min Siemens S7 PLC Controls, Condition: as new, Immediately available EXW our Warehouse Enger, Germany, Length: 200 to 600 mm, Width: 200 to 500 mm, Carton size min.: 250 mm x 200 mm x 150 mm, Carton Size max.: 600 mm x 475 mm x 600 mm

Fabricante NICOLÁS CORREA Modelo L30-43 Año 1998 CNC HEIDENHAIN TNC 426 PB Superficie de la mesa 6.120 x 1.000 mm Peso Admisible sobre mesa 20.000 Kg. Recorridos (X/Y/Z)) 4.300 mm Avance Rápido Ejes 12.000 mm/min Avance Máximo de Trabajo 5.000 mm/min Cabezal de Giro Automático 2. 5º – 2. 5º Cono Cabezal ISO-50 Potencia Motor Principal 30 kW Gama de Revoluciones 20 – 3.000 r.p.m. Cargador Automático Herramientas INCLUIDO Posiciones en cargador de htas. 40 Equipo de Taladrina con sistema de filtrado de papel INCLUIDO Volante electrónico portátil HEIDENHAIN HR-410 Peso de la Máquina 28.000 Kg.

Fabricante NICOLAS CORREA Modelo L30/58 Año 1999 CNC HEIDENHAIN TNC 430 D Mesa Superficie de la mesa 6.120 x 1.000 mm Peso max permitido sobre mesa 20.000 kg. Recorridos y avances Longitudinal (Eje X) 5.850 mm Transversal (Eje Y) 1.200 mm Vertical (Eje Z) 2.000 mm Avance rápido ejes 12.000 mm/min Avance max. de Trabajo 5.000 mm/min Cabezal Cabezal de giro automático 2. 5º – 2. 5º Cono cabezal ISO-50 Potencia motor principal 30 kW Gama de revoluciones 20 – 3.000 r.p.m. Equipamiento Cargador automático merramientas INCLUIDO POsiciones en almacén de herramientas 60 Volante Portátil HEIDENHAIN HR-410 Evacuador viruta INCLUIDO 4 mesas supletorias INCLUIDO Preparación oara 4º Eje INCLUIDO Refrigeración interna 20 Bar INCLUIDO Equipo de taladrina con sistema de filtrado de papel INCLUIDO Otros Peso de la Máquina 31.000 kg. Potencia total instala ...

Grundy Tank 400L / 90Gallon Insulated and Clad in welded Stainless Steel 50mm of insulation Bolted top lid with internal cooling coil attached Temperature probe pocket working pressure 30psi This is a SECOND HAND item and is sold as seen For more information and more available stock please visit us at - advancedbrewing.co.uk

General SKU312W1494 LocationBarneveld CEcheck MakeAnlagenbau Stampfer GmbH Main Features Motor2.2 KW Length11466 mm Width1637 mm Specified Features - Conveyor belt MaterialStainless steel 1.4301 (304), Stainless steel 1.4571 (316Ti) Conveyor beltcheck Belt width1637 mm, (1000mm) Belt lengthTotal ca. 11,466 m With motor2,2 kW, 290/500 volt, 1405 rpm Belt speed47 rpm Information TypeAS-WRB-1000 Mach.No.144.0001 Year of construction2014 Floorspace11,4x1,6 m Total height1,0 m Weight5500 kg Extra Specificationsbelt rolls HDPEConveyor beltsStampfer HaanConveying systems > Conveyor beltsBrand > Stampfer Haan What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many  ...

General SKU334T899 MakeFriedhelm Stechel GmbH LocationBarneveld CEcheck TypeADE120-100 Main Features MaterialStainless steel Motor1.5 KW Inlet diameter748 mm Specified Features - Coating pan MaterialStainless steel 1.4301 (304) Coating pancheck Capacity150 Ltr. Batch sizemax. 130 kg Pan diameter1200 mm Pan depth620 mm In-/Outlet748 mm Motor1,5 kW 230/400 Volt Pan speed19 rpm Information No.D20909 Year of construction2009 Mounted on framecheck Floorspace2,5x1,8 m Total height2,3 mCoating pansFriedhelm StechelCoating pans > Coating pansBrand > Friedhelm Stechel What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

Brand: Berstorff Type: ZE 25 compounding line Serial no.: 90200771-0010/2002 Year of manufacturing: 2002 Working hours: 1.378 Screw dimension: 25 mm Screw L/D: 44 Dimensions (LxWxH): 4.500 x 1.200 x 2.200 mm Weight: 1.350 kG Line configuration: – 1x Gravimetric powder feeding system from Brabender – 1x vent port for degassing, including vacuum pump – Filament die with 6 cavities – Cooling roll with tempering device – Pelletizer with adjustable speed – Central control cabinet Other: All documentation available in German The machine was originally used for biomaterials

This 3-axis AMADA LC-3015F1NT 4kW CO2 was manufactured in 2016. It features a 4000-watt CO2 resonator and handles a maximum sheet size of 3000x1500mm, including a tower. If you are looking to get high-quality laser cutting capabilities, consider the AMADA LC-3015F1NT machine we have for sale. Contact us for more information about this machine.

This Coord3 ARES NT was manufactured in 2017. Ideal for precision measurement tasks, this CMM machine offers reliable performance for quality control in various industries. Contact us for more information.

This 3-axis Coord3 ARES NT-L 10.7.5 CNC was manufactured in 2018. It features a high-precision RENISHAW PH20 motorized indexing probe head, RENISHAW UCC controller, and a robust aluminum alloy frame. The machine includes a black granite worktable with threaded holes for secure workpiece fixation. Ideal for detailed 3D measurements with a maximum speed of 500 mm/sec and acceleration of 1700 mm/sec². Contact us for further details regarding this machine.

This Coord3 ARES II was manufactured in 1999. It is a coordinate measuring machine with a table load capacity of 1,200 kg and overall dimensions of 4500 × 3200 × 2800 mm. The machine weighs 7,500 kg. Consider the opportunity to buy this Coord3 ARES II coordinate measuring machine. Contact us for more information.

This 3-axis ZEISS Contura 7/10/6 RDS was manufactured in 2019 and features a robust motorized CNC drive system with a maximum vector speed of 465 mm/s. It includes the ZEISS RDS-C articulating head and VAST XXT TL3 sensor, capable of scanning speeds up to 150 points/second. Ideal for precise measurements with a maximum workpiece weight of 730 kg. Consider the opportunity to buy this ZEISS Contura 7/10/6 RDS CMM machine. Contact us for more information about this machine.

General SKU204X026 MakeEntecon Ltd UK TypeAMC Aero Mechanical Conveyor LocationBarneveld Main Features Motor2.2 KW Length5200 mm Inlet diameter75 mm Specified Features - Vertical screw conveyor MaterialStainless steel Vertical conveyor screwFloveyor (1x) Tube-modelcheck Diameter75 mm Lengthapprox 5200 mm Inletdia. 200 mm Outletdia. 195 mm Motor2,2 kW, 220/380 volt Information No.02-C3S-5446 Year of construction2002 Floorspace6,50x0,60 m Total height0,80 m Weight250 kgVertical screw conveyorsEnteconConveying systems > Vertical screw conveyorsBrand > Entecon What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

General SKU342W880 MakeHosokawa Micron Type12 VDC-11 Mach.No.101189 Year of construction1990 Pressure Working pressure1 Bar Vacuum possiblecheck Working pressure jacket6 Bar Technical specs Max. temperature120 °C Main Features MaterialStainless steel Volume2785 Ltr. Motor7.5 KW Specified Features - Conical dryer Conical dryercheck Capacity2785l ( netto 1200L) Largest cone diameter1770 mm Cone height2418 mm Dished topcheck ManholeDN450 Stainless steel armcheck Top drivecheck Motor7,5 kW, 400V Motor0,75kW, 400V With half coil jacketcheck vollume 95l Max. temperature120°C Bottom outletcheck Outlet with sliding valvecheck MaterialStainless steel 1.4435 (316L) Information LocationBarneveld Floorspace2,0x2,0 m Total height4,2 m Weight3000 kg Extra Specificationsnetto 3,7m² heating suface. with :sanitary screw. with Perinox bag Filter. Conical dryersHos ...

General SKU279U510 MakeEscher Wyss LocationBarneveld TypeFTK 135/450 Main Features MaterialMild steel/Stainless steel Motor0.6 KW Surface1.35 m2 Specified Features - Fluid bed dryer continuous Continuous fluidbed dryercheck Surface1.35m² Bed sizes3000x450 mm Product inlet450x200 mm Product outletDia: 80 mm Number of sections:3 Air inletDia:380x300 (3x) Air outletDia: 270mm Vibro motor0,6 kW,220/380 volt, 980 rpm (2x) Without motorcheck MaterialMild steel, Stainless steel 1.4301 (304) Information No.2710214 Year of construction1980 Mounted on mild steel framecheck Floorspace3,8x1,03 m Total height2,7 m Weight2000kgFluid bed dryers continuousEscher WyssDryers > Fluid bed dryers continuousBrand > Escher Wyss What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide  ...

General SKU293X399 MakeLauda TypeT2200 W Mach.No.LWP104-13-0007 Year of construction2022 Main Features Heating (medium)Electric Capacity3.1 KW Temp.120 °C Specified Features - Temperature control unit Temperating machinecheck Water heatercheck With coolingcheck Temperature-25°C/120°C Tank capacity7 l. With pumpcheck Motor3,1 kW, 230 volt With temperature controllercheck Information LocationBarneveld Mounted on wheelscheck With switchgearcheck Floorspace0,45x0,70 m Total height0,80 m CEcheck Extra SpecificationsCool medium R404ATemperature control unitsLaudaHeat exchangers > Temperature control unitsBrand > Lauda What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Ba ...

Robot Cobot Universal Robots UR10 CB3.1 YOC 07/2017 Number of axes: 6 Max. load capacity: 10 kg Max. working range: approx. 1300 mm Package Contents : Robot,Control,Cable,Teach Panel 2 weeks commissioning warranty.No further warranty In addition, spare parts are always available from stock. Robot is fully functional and can be viewed Auction amount is ex works Freely loaded The indicated sales price is plus the statutory VAT of 19%. Shipping costs abroad on request. Please enter your country, city and zip code.

Transportable 1000L Bulk Container Tank Manufacturer: Bison Stainless Steel, Top Entry Manway. Previously used for spirits This is a SECOND HAND item and is sold as seen For more information and more available stock please visit us at - advancedbrewing.co.uk

General SKU222W218 MakeWalter Brucks Typeunknown (missing type plate) Mounted on framecheck Main Features MaterialCopper Motor2.2 KW Inlet diameter600 mm Specified Features - Coating pan MaterialCopper Coating pancheck Pan diameter960 mm Pan depth570 mm In-/Outlet600 mm Motor2,2kW, 380Volt Pan speed16 rpm Information LocationBarneveld With switchcheck Floorspace1,3x0,95 m Total height1,5 m Weight260 kgCoating pansWalter BrucksCoating pans > Coating pansBrand > Walter Brucks What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

PET Coextrusion + Inline ILLIG RDKP72g Thermoforming Line, Age 2010, this equipment is suitable for PET, PP & PS Trays, Fruit & Vegetable baskets etc. :-, Inline S Plastic SRL PET Coextrusion line to produce pet sheet in-line with ILLIG RDKP72g 4-Station Thermoformer (.samplastco. hole punch station) Age 2010 :, Maximum output 680 kg/ hr, Maximum sheet width 800 mm, The line includes:, Electrical Control Panel, MSM Plastic Engineering Gravimetric Feeder, fed directly from the PET Dryer + additional Component for masterbatch or additive, Main extruder Model ED 100-40 dia. Ø100 mm, L/D 40, BP Plast BDO X2 100 Double plate hydraulic screen changer, MAAG Gear pump, Co-extruder Model E60-40 dia. Ø60 mm, L/D 40 with Gravimetric feeder, BP Plast Single plate hydraulic screen changer, MAAG Gear pump, 3- Layer (ABA) Melt Feed Adapter, Special extrusion die for PET, width 900 mm, 3-Roll Polished ...

General SKU203W030 LocationBarneveld CEcheck MakeHuber Main Features Heating (medium)Electric Capacity1.5 KW Temp.40 °C Specified Features - Temperature control unit Temperating machinecheck Electric heatingcheck Heating medium:R507 Heating capacity1,5 kW Electric capacity230 volt Temperature-10°C/+40°C With pumpcheck Information TypeUC015 Mach.No.43433 Year of construction2000 Mounted on wheelscheck With switchcheck Floorspace0,41x0,50 m Total height0,63 m Weight65 kg Extra Specifications- coolerTemperature control unitsHuberHeat exchangers > Temperature control unitsBrand > Huber What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

General SKU204U932 LocationBarneveld CEcheck MakeSingle Pressure Working pressure17 Bar Main Features Heating (medium)Electric Capacity6 KW Temp.30 °C Specified Features - Temperature control unit MaterialStainless steel Temperating machinecheck With coolingcheck Capacity6 kW Temperature-5/+30°C With pumpcheck 3,1m³/h (2x) With temperature controllercheck With controlcheck Information TypeChill Advanced C-6-W Mach.No.152171 Year of construction2015 Mounted on wheelscheck With switchcheck Floorspace1,16x0,65 m Total height1,65 m Weight265 kg Extra SpecificationsPower 11.7 kVA, 16.3A, test pressure 21 bar, refrigerant medium R134a, volume 4.0 kg Temperature control unitsSingle TemperiertechnikHeat exchangers > Temperature control unitsBrand > Single Temperiertechnik What you can expect from Foeth: -- Machine is in working condition -- At a reduced price com ...

GAMMA MECCANICA GM 125 COMPAC - TOTALLY RECONDITIONED, Extrusion line with pre-compactor, Nominal throughput rate 700-800 kg/h depending on the type of material and feeding rate, Average energy consumption : 0.25-0,30 kwh/kg, The line includes:, Loading belt, tunnel metal detector, compactor with dosing unit, extruder with 125 mm screw diameter, 35 L/D, nitrided screw and barrel in very good conditions. The line was working with LDPE film and PPL non woven, semi-automatic, non-stop hydraulic screenchanger, oleo-dynamic pack, water ring pelletizer, drying centrifuge, recycling water tank, electric cabinet for the complete management of the line, The line is offered reconditioned, See Constructors [description](.gamma-meccanica.it/en/plastic-recycling/plastic-recycli ng-compac/) for a new line like this one, availability: immediate, capacity: 600-950 kg/h with only 0,25-0,30 kwh/kg used, c ...

General SKU397X1416 LocationBarneveld CEcheck Pressure Working pressure28 Bar Main Features Heating (medium)Electric Capacity9 KW Temp.120 °C Specified Features - Temperature control unit MaterialCopper Temperating machinecheck (cooler/chiller) Water heatercheck Electric heatingcheck Electric capacity7,8 kW, 400 volt With coolingcheck (water) Capacity45 l/min circulation (pump) Temperature—20 / 120 °C Tank capacity6,70 l. With pumpcheck Capacity55 l/min With temperature controllercheck (as is) Information MakeLauda TypeXT950 W Mach.No.LWP521-15-0004 Mounted on wheelscheck With switchcheck Floorspace0,46 x 0,56 m Total height1,30 m Weight180 kg Extra SpecificationsCooling medium R404a, pressure 19-28 bar, volume 2 kgTemperature control unitsLaudaHeat exchangers > Temperature control unitsBrand > Lauda What you can expect from Foeth: -- Machine is in wo ...

General SKU439X1389 LocationBarneveld MakeWalter Brucks TypeVII Main Features MaterialStainless steel Inlet diameter350 mm Specified Features - Coating pan Coating pancheck Capacity10 l. Pan diameterø 600 mm Pan depth360 mm In-/Outletø 350 mm Pan can be tiltedcheck Motor380 V With variable speed drivecheck Pan speed10—45 rpm With spraying armcheck With dosing pumpcheck Motor560 W, 6 bar, MaterialStainless steel 1.4301 (304) Information No.4950 Year of construction1974 Mounted on framecheck Floorspace1,20 x 0,80 m Total height1,60 m Weight250 kg Extra SpecificationsWith Terlet stainless steel pressure vessel, volume 25 L, maximum pressure 6 bar, jacket pressure 3 bar, allowable temperature 144 °C.Coating pansWalter BrucksCoating pans > Coating pansBrand > Walter Brucks What you can expect from Foeth: -- Machine is in working condition -- At a reduced pri ...

General SKU322X553 LocationBarneveld MakePuc Probst & Class Motor Motor power2.2 kiloWatt Main Features MaterialStainless steel Motor2.2 KW Inlet diameter55 mm Specified Features - Colloid mill MaterialStainless steel Colloid millcheck Rotor sizesø 60 x 40 mm Teethed rotorcheck With hoppercheck ø 300 x 500 mm Hopper jacketedcheck Inletø 55 mm Outletø 32 mm Motor2,2 kW (380 V, 2840 rpm) Information TypeK 60 No.92030 Mounted on wheelscheck With switchcheck Floorspace0,90 x 0,46 m Total height1,10 m Weight110 kgColloid millsPuc Probst & ClasMills > Colloid millsBrand > Puc Probst & Clas What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machi ...

General SKU390X987 MakeBühler LocationBarneveld CEcheck TypeOTW 150 Main Features MaterialStainless steel Motor0.55 KW Surface1.5 m2 Specified Features - Fluid bed dryer continuous Continuous fluidbed dryercheck Surface1,5 m² Product inletDN200 Product outletDN200 Number of sections:1 Air inletDN400 Air outletDN400 Vibro motorcheck Motor0,55 kW, 500 V, 1380 rpm With variable speed drivecheck (34 — 171 rpm) With fancheck Motor75 kW, 290/500 V, 2970 rpm, (Ex) Capacity2250 kg/h Cleaning by air pulsecheck Max. temperature200 °C MaterialStainless steel 1.4541 (321) Information No.20.330.944 Year of construction2010 Mounted on framecheck Floorspace3,35 x 1,0 m Total height1,90 m Weight600 kg Extra SpecificationsCooling air volume: approx. 8100 m³/h Throughput capacity: max. 2250 kg/h Product inlet temperature: 150 °C Product outlet temperature: approx. ...

General SKU413X1260 MakeNema LocationBarneveld CEcheck TypeKRS 0500x6800 Kersae-220 Main Features Motor7.5 KW Length6800 mm Inlet diameter300 mm Specified Features - Vertical screw conveyor MaterialMild steel, Stainless steel 1.4404 (316L) Vertical conveyor screwcheck Tube-modelcheck Diameter500 mm Length6800 mm Between inlet and outlet6000 mm Shaft diameter165 mm Pitch70 mm Inletø 300 mm Outletø 400 mm With jacketcheck (Jacket: 180 Ltr.: Shaft: 110 Ltr.: Max. temp. : 10 / 80 °C) Max. temperature10 / 150 °C Motor7,5 kW, 400/690 V, 1468 rpm Screw speed40 rpm Information No.K62.281-014 Year of construction2004 Floorspace8,50x0,66 m Total height1,00 m Weight4000 kg Extra Specifications Product volume: 830 L: shell volume: 180 L: shaft volume: 110 L. Shell design pressure: 6 bar: test pressure: 8.6 bar. Shaft design pressure: 6 bar: test pressure: 8.6 b ...

General SKU390X1042 MakeBühler LocationBarneveld CEcheck TypeOTW-150 CRF Main Features MaterialStainless steel Motor30 KW Surface1.66 m2 Specified Features - Fluid bed dryer continuous Continuous fluidbed dryercheck Surface1,66 m² Bed sizes2024 x 822 mm Product inletDN200 Product outletDN200 Air inletDN400 Air outletDN400 With fancheck Motor± 30 kW 500V 2960 rpm MaterialStainless steel 1.4541 (321) Information No.10506369 Year of construction2012 Floorspace2,3 x 0,92 m Total height1,9 m Weight600 kg Extra SpecificationsOperating parameters: Maximum operating temperature: 200°C Pressure range: 100 / –50 mbar Air capacity: approximately 8,160 m³/h Material throughput capacity: up to 2,250 kg/h Included equipment: Pulsator with electric motor rated at 0.55 kW, 290/500 V, with an adjustable operating speed range of 34–171 rpm Piller blower, supporti ...

General SKU390X1037 MakeBühler LocationBarneveld TypeOTW-150 CRF Main Features MaterialStainless steel Motor30 KW Surface1.66 m2 Specified Features - Fluid bed dryer continuous Continuous fluidbed dryercheck Surface1,66 m² Bed sizes2024 x 822 mm Product inletDN200 Product outletDN200 Number of sections:1 Air inletDN400 Air outletDN400 Motor0,55 kW, 500 volt, 1360 rpm With variable speed drive34-171 rpm MaterialStainless steel 1.4541 (321) Information No.10506368 Year of construction2012 With switchcheck Floorspace3,40x1,30 m Total height2,20 m Weight1000 kg Extra SpecificationsOperating parameters: Maximum operating temperature: :200°C Pressure range: :100 / –50 mbar Air capacity: approximately :8,160 m³/h Material throughput capacity: up to :2,250 kg/hIncluded equipment: Pulsator :with electric motor rated at :0.55 kW, :290/500 V, with an a ...

General SKU390X1051 MakeBühler LocationBarneveld TypeOTW 300 Main Features MaterialStainless steel/Aluminium Motor0.55 KW Surface3 m2 Specified Features - Fluid bed dryer continuous Continuous fluidbed dryercheck Surface3 m2 Product inletDN200 Product outletDN200 Air inletDN600 Air outletDN600 Vibro motorcheck Motor0,55 kW, 500 volt, With variable speed drive32-171 rpm With fancheck Fima Motor75 kW, 290/500 volt, 2970 rpm Capacity16.200 m3/h Fluidbed dryers continuous Cooling beltcheck With motor0,55 kW, 290/500 volt, 1380 rpm Belt speed34-171 rpm MaterialStainless steel 1.4571 (316Ti) Information No.20330614 Year of construction2007 With switchcheck Floorspace4,80x2,40 m Total height1,20 m Weight1200 kg Extra SpecificationsCap. 3m2, product flow rate 2500-4500 kg/h, : with Fima blower, type RM51U500KGB GL360 and rotary valve Fluid bed dryers continuo ...

General SKU390X1052 MakeBühler LocationBarneveld CEcheck TypeOTW 150 Main Features MaterialStainless steel Motor0.55 KW Surface1.5 m2 Specified Features - Fluid bed dryer continuous Continuous fluidbed dryercheck Surface1,5 m² Product inletDN200 Product outletDN200 Number of sections:1 Air inletDN400 Air outletDN400 Vibro motorcheck Motor0,55 kW, 500 V, 1380 rpm With variable speed drivecheck (34 — 171 rpm) With fancheck Motor75 kW, 290/500 V, 2970 rpm, (Ex) Capacity2250 kg/h Cleaning by air pulsecheck Max. temperature200 °C MaterialStainless steel 1.4541 (321) Information No.20.330.943 Year of construction2010 Floorspace3,35 x 1,0 m Total height1,90 m Weight600 kg Extra SpecificationsCooling air volume: approx. 8100 m³/h Throughput capacity: max. 2250 kg/h Product inlet temperature: 150 °C Product outlet temperature: approx. 32 °C Design tempera ...

General SKU390X1009 MakeBühler LocationBarneveld CEcheck TypeOTWG-160-C (static) Main Features MaterialStainless steel Motor0.55 KW Surface1.59 m2 Specified Features - Fluid bed dryer continuous Continuous fluidbed dryercheck Surface1,59 m² Product inlet190 × 110 mm Product outletDN 150 Air inletDN 400 Air outletDN 400 Motor0,55 kW 290/500 V With variable speed drivecheck pulsator 26–128 rpm With fancheck (PILLER: Type: 40351KE 80315) Motor30 kW Capacity3.1 m³/s Max. temperature250 °C Fluidbed dryers continuous Cooling beltcheck MaterialStainless steel 1.4306 (304L), Stainless steel (Sandvik 1200SA) Information No.10 263 218 Year of construction1996 Mounted on framecheck Weight1050 kg Extra SpecificationsVolume 2,7 m3 max pressure till 250°C, +0,2 bar, max pressure till 150°C, 0,1 bar, max temperature 250°C Fluid bed dryers continuousBühlerDryer ...