forging hammer used for sale

GFM SX-45 Radial Forging Machine Year: 70’ Number of forging hammers: 4 Forging force (per ram): 800 ton Number of forging strokes (per ram): 265 /min Hammer length: 490 mm Max workpiece: Ø450/□ 340 Hollow spindle I.D.: 295 mm Chuck head max clamping: 450 mm Stroke of chuck head A: 7.500 mm Stroke of chuck head B: 8.500 mm Chuck head max feed speed: 300 mm/sec Adjustable chuck head feed speed: 0-140 mm/sec Adjustment of rams (on diameter): 200 mm Cooling water inlet pressure: 3-8 atm Cooling water max inlet temperature: 30°C Circuit flow: free Cooling water flow: 140.000 l/h Compressed air pressure: 6-8 atm Compressed air connecting point: ca. 2.5-3 m3/min Connected power: 400V (), 650KW, 6000V, 500KW () Total weight: 540 Ton

with vertical matrix connector Max. work-piece diameter: 140 mm Max. diameter of upset flange: 180 mm Nominal force of upset slide: 12500 kN Force on clamping slide with dies closed: 12500 kN Stroke of: -Upset slide: 460 mm -Upset slide after closing of dies: 310 mm Number of continuous slide strokes per minute: at least 32 Electric motor power: 75 kW Machine dimensions: -Length: 8035 mm -Width: 4800 mm -Height: 3575 mm Machine weight: 140 tons

2000 Ton Sumitomo Hot Forging Press line Year 2006 Stroke 350 mm (13.78") Strokes per min 75 Shut height 850 mm (33.47") SlideAdj. 7 mm (.27") Ram size 1200 mm LR X 1300 mm FB Bed size 1320 mm LR X 1300 mm FB 4 stage transfer system Slide knockout Bottom knockout Scrap System Dual Die Changer Extra Die Shoes Billet Heater and Billet Saw Also Available This line was used by HONDA to make transmission gears, It takes a billet, cuts it to size, heats it to 1300 C then the press hits it 4 times. It can determine good from bad parts, the bad parts get sent to a quench tank, the good parts get sent into a cool down conveyor that you can pick the parts up by hand at the end. The entire system was ran by one operator.

Eccentric shaft for hot forging press K8548 6300T Weight, kg 27 800

Capacity: 1 200 T, Total stroke: 500 mm, Stroke of main crank shaft: 318 mm, Stroke of mobile die: 215 mm, Stroke/min: 27, Bar diameter: 50-90 (150) mm, Max diameter of peace: 152mm, Max weight of piece: 5 kg, Main motor power: 75 KW, Area of machine : 6400 x 4420 mm, Hight of machine: 3830 mm, Weight: 128.0 T

Drive gear for hot forging press K8548 6300T Weight, kg 15 700

Effort 2000t moving matrix 280 mm landing pad 570 mm landing slider after closing the matrices 390 mm Number of moves of the ram, stroke / min 25 Electric motor power 160 kW Dimensions, mm: LWH = 856053604850, the level above the floor is 3200. Weight of the car without electricity: 239.8 tons. Weight of the bed: Front part: 82 tons. Rear part: 55t. Weight 270 ton

Driven gear for hot forging press 6300T Weight, kg 1300

Clutch hub for hot forging press K8548 6300T Weight, kg 7100

Herdwage n Glühöfen Kammerschmiedeöfen Wärmebehandlungskammeröfen Wärmebehandlungs Kammeröfen für ALU-Blechcoils Wärmebehandlungs Schachtöfen Haubenöfen Härten Anlassen bei niedriger und hoher Temperatur Glühen Normalglühen Austenitisieren Spannungsfreiglühen Vorwärmen vor dem Schmieden Rollenherdöfen Kontinuierliche Öfen für die Wärmebehandlung von buerstlein Nichteisenmetallbändern Anlage für Wärmebehandlung von Wagenfahrgestellgüsse Öfen für die Wärmebehandlung von Transformatorblech Warmrundlaufprüfanlagen Öfen für Feuerwiderstandsprüfungen zirlguss Hubbalken und Hubherdöfen Schachtofen Haubenofen Rollenherdöfen Durchstoßöfen Härten Glühen Normalisieren Weichglühen Vergüten Anlassen Entspannen Durchschuböfen Hubbalkenöfen Hubherdöfen Trockenöfen Rollenherdöfen Drehherdöfen Kammeröfen Mehrkammeröfen Verfahrbare Haubenöfen Herdwa ...

Max. diameter of initial blank: 30 mm Blank length: -Min.: 120 mm -Max.: 300 mm Max. diameter of upset flange: 60 mm Upset slide nominal force: 2500 kN Max. force on clamping slide with dies closed: 2500 kN Stroke: -Movable die: 100 mm -Upset slide (full): 220 mm -Die closing: 140 mm Slide strokes per minute: 45 Machine overall dimensions: -Length: 6050 mm -Width: 4600 mm -Height: 2260 mm Machine weight: 24680 kg

6500ton Open Die Forging Press HJ / Seonam (Korea) Design: Eastern European Corporation Installation: 2006/2008 Press Type: Four column push down Oil hydraulic system Nominal force (static working pressure of 320 bar): 5,000 Tons Up-setting force (static working pressure of 420 bar): 6500 Tons Daylight: 5,200 mm Stroke of Movable cross head: 2,700 mm Main Ram dia. (Center cylinder): 1 set - ￠950 mm Side Ram dia. (Side cylinder): 2 sets - ￠750 mm Return cylinder Ram dia: 2 sets - ￠300 mm Moving Table Width: 2,600×Length 6,600 mm Moving Table stroke (center to both side 2,750mm): 5,500 mm Approaching speed: 300 mm/sec Main cylinder Forging speed (2,200 tons/ 320 bar): 163 mm/sec All cylinder Forging speed (5,000 tons/ 320 bar): 73 mm/sec Up-setting Forging speed (6,500 tons/ 420 bar): 10 mm/sec Return speed: 270 mm/sec Hydraulic Main pump: 12 sets  ...

Nominal force 1250 ton - first stage : 260 tons, - second stage : 800 tons, - third stage : 1250 tons, Slide stroke 1250 mm Distance between table and slide 2650 mm Main cylinder dia Ø 500mm Return cylinder dia. ( two) 2xØ400mm Distance between column 1800mm Table size width / length 1250 / 3150 mm Main motor power 150 kW Machine dimensions L x W x H 16950 x 12100 x 11410 mm Weight 265000 kg Forging manipulator FS2ЕТС -2T also available 1T and 700t

Complete Mechanical Upgrade by GFM, with increase of Power to 900 Ton/hammer and new CNC in 1991 Numbers ̈of Hammers: 4 Forging force: 3.600 Ton (900t per hammer) Strokes per minute: 270 Maximum diameter of forging: - circular cross section: Ø 400 mm - square cross section: 320 mm Minimum output diameter: - circular: 60 mm - square: approx 50 mm Maximum length of forging with/without lateral reception: 8.000 mm / 9.700 mm Feed of manipulator A: 7.140 mm Feed of manipulator B: 9.940 mm Workpìece weight: 2500 kg Total power supply (nominal power): ca 1.600 kW Machine weight: 493.000 kg

Capacity: 1600 tons Slide stroke: 300 mm Slide stroke length at maximum force: 0,16 mm Distance adjustment between tableand slider: 10 mm Slide stroke number in 1 min: 75 Length of a rod: 920 mm The closed height: 660 mm Table overall dimensions: 940x1200 mm Table height above floor level: 450 mm Slide overall dimensions: 860x910 mm The size of lateral windows: -Height: 560 E5931468 mm -Width: 600 mm Main motor: 110 kW Press overall dimensions: -Length: 5060 mm -Width: 3940 mm -Height above floor level: 5125 mm Press weight: 120 tons

Capacity: 1600 tons Slide stroke: 300 mm Slide stroke length at maximum force: 0,16 mm Distance adjustment between table and slider: 10 mm Slide stroke number in 1 min: 75 Length of a rod: 920 mm The closed height: 660 mm Table overall dimensions: 940x1200 mm Table height above floor level: 450 mm Slide overall dimensions: 860x910 mm The size of lateral windows: -Height: 560 mm -Width: 600 mm Main motor: 110 kW Press overall dimensions: -Length: 5060 mm -Width: 3940 mm -Height above floor level: 5125 mm Press weight: 120 tons

LASCO FP 222 S hydraulic press was built in Germany by Lasco Umformtechnik GmbH. The machine has been continuously maintained and upgraded throughout its service life. In 2022, a major upgrade was carried out, which included replacing the electrical cabinet, installing light curtains and adding a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel. The LASCO FP 222 S is an extremely versatile hydraulic press designed for the production of extremely precise, repeatable and yet complex components used in the broadly defined automotive or machinery industry. Its main application is hot and cold forging. The use of a die cushio in the lower work table and the large slider stroke means that the machine can also be used as a deep drawing press. All machining processes are performed with a high press force of up to 200 tonnes, which, combined with the highly dynamic slider, guarantees the b ...

LASCO TSP 160 S forging press was built in Germany by Langenstein & Schemann A.G. (Lasco Umformtechnik GmbH). The machine has been continuously maintained and upgraded throughout its service life. In 2019, a major upgrade was carried out, which included replacing the seals, upgrading the control system, installing light curtains and adding a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel. The LASCO TSP 160 S is an extremely versatile hydraulic press designed for the production of extremely precise, repeatable and yet complex parts. It is ideal for forges and industrial plants that require high press forces and high repeatability of the manufactured parts. Its main purpose is die forging, metal stamping and metal forming, especially hot forming of steel or aluminium workpieces. It also enables punching, calibration of forgings, trimming and blanking of workpieces after the forgin ...

no. of strokes:150 /min impact energy:420 kJ distance lower die block / ram gudeway:435 mm Throat:425 mm steel forging - rectangular up to:110 mm steel forging - diameter up to:125 mm power requirement:22,0 kW weight of hammer:3,9 t weight of anvil:3,0 t ram hammer weight:200 kg weight:6,9 t dimensions (WxDxH):1,1 x 2,3 x 2,4 m

Complete overhoul with new electrics in 2016 Lift load: 1000 kg Load moment: 2400 mkg Max Rds: 400 mm Min Rds: 100 mm Speed: 0-90 m / min Driving power: 22 kW / 380V / 50Hz Total weight: 10,5 t Mode of operation: oil-hydraulic

Upsetter STANKO RYAZAN B1141 Nominal effort 1250t Max. workpiece diameter 140 mm Max. upset flange diameter 180 mm Stroke of moving slider 220 mm Stoke of upsetting slider: total/working - 460/310 mm Strokes per min 30 Matrix dimensions 700x260x820 mm (LxWxH) Distance upsetting slider and matrixes 180 mm Electric motor power 75 kW Machine overall dimensions 6400x4365x3340 mm Weight 135t Excellent condition. Very little use- it shows from the gears. Can be inspected in operation

We have an EUMUCO RW1 Reduce Forging Roll Machine available for sale. Manufacturer: EUMUCO Model: RW1 Condition: Used Technical specifications: Maximum workpiece diameter: 55 mm Rolling segment diameter: 370 mm Usable width of middle roll: 500 mm Usable width of outer roll: 160 mm Maximum workpiece length, middle: 570 mm Maximum workpiece length, outside: 890 mm Roll adjustment: 15 mm Drive power: 30 HP Electrical: 230/460 V Approximate weight: 22,000 lbs (10,000 kg) Please let me know if this equipment could be of interest to you, and I can provide

pressure: 4000 t stroke: 380 mm dayligth: 1050 mm distance between columns: 1580 mm table-size: 1520 x 1600 mm dimension of ram: 1470 x 1500 mm ram adjustment: 15 mm strokes of ram per min.: 50 ejector path: 31 / 70 mm main drive: 200 kW height over floor: 7520 mm total power requirement: ca. 250 kW weight of the machine ca.: 245 t dimensions of the machine ca.: 4,4 x 4,6 x 7,5 m complete forging line includes an - Smeral Hot Forging Press - induction heater - Manyo 460-millimeter forging roll - manipulator with forging roll link - SMERAL 500-ton trimming press The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

nominal force:2500 t stroke:600 mm cycle time:13 - 18 s distance between columns:1720 mm Distance table/ram, max. stroke up, adjustment up:2600 mm table surface area:1720 x 1800 mm allowed max. force:4000 t blow die to die:5000 t ram surface:2100 x 1320 mm capacity of ejector in table:40 t ejector stroke in table:250 mm ejector surface area in table:900 x 820 mm capacity of ejector in ram:6 t ejector stroke in ram:40 mm spindle diameter:425 mm power requirement:900,0 kW weight:335,0 t Dimensions (WxDxH):3,4 x 4,6 x 9,7 m height over floor:8,3 m fully-automated forging line:to produce axle shaft

impact energy:207951 mkg ram hammer stroke:660 mm no. of strokes:100 /min impact energy:2040 kJ distance lower die block / ram gudeway:660 mm Throat:750 mm steel forging - rectangular up to:240 mm steel forging - diameter up to:270 mm power requirement:75,0 kW weight of hammer:16,5 t weight of anvil:15,5 t ram hammer weight:750 kg weight:32,0 t dimensions (WxDxH):3,2 x 1,45 x 3,45 m Mode of operation:pneumatisch

- Hand & foot operation - integrated anvils - massive substructure - Hammer weight: 25 kg - Stroke: 250 rpm - Lifting height: 250 mm - Extension: 200 mm - Cylinder: 125 mm - Work shoehe: 765 mm - Engine power: 3 kW - Voltage: 400 V - Ground WxHxD: 460 x 1520 x 970 mm - Weight: approx. 670 kg

Stock# U2293-1 Used stainless steel contact parts horizontal hammer mill by Pallmann (Germany) type PHM 600-350. Mill has internal dimensions of milling chamber L 600 mm x W 350 mm. Top of milling chamber is manually rised. At the bottom mill has a discharge outlet through the screen. At the top of milling chamber there is installed static knife for grinding of product. Rotor has diameter 500 mm x width 345 mm. On the rotor there are 24 rows with hammers, each row consist of 4 hammers. Total number of hammers is 96. Rotor and hammers are designed in non-corrosive steel. Rotor is belt driven by el. motor 75 kW, 2975 rpm, 380/660 V, 50 hz. Mill has side feeding inlet with dimensions 350 mm x 265 mm. Product is moved into milling chamber through three screws. Screws are driven by el. motor 0.55 kW, 2800 rpm, 220/380V, 50 hz and varispeed gearbox with manual adjustment of outgoing rotatio ...

Blacksmith hammer / air hammer Zeva machines 16 bear Air / forging hammer 16 bear Max 250 strokes/min Working cylinder diameter 90 mm Stroke approx. 170 mm CLOUT approx. 16 bear Anvil is connected to machine Ambosswerzeug can be changed CLOUT and Geschwindegkeit can be controlled with foot switch and hand 1.5 KW, 250 kg If you are interested in air hammers with 25Baer, 40Baer, 55Baer and 75Baer write me a short message!

Lefort BR1260 Shredder for sale. The machine has 10 hammers, 500 Hp electric engine. The machine has a low hours (less than 2.500). THe machine's capacity is around 20-25 tons/hours which means this is an exelent machine. Price is including the separation and conveyor system to, which is including the followings. -Feeding conveyor (1260 mm wide) -Vibrating table -magnet drum (type:BMK 100-180TML ) -1 conveyor for metal scrap with cabin for separation -1 big conveyor for nonferrous and other materials Bbmc3fzwrj -1 magnet belt -1 magnet separation system ( separating the non-ferrous metals from the dust) that system is including a vibrating table, and electric box (type:EC-X650 ) -2 conveyors from non-ferrous metal and for dust. VERY IMPORTANT: Every part of the system and every function works. +Option: We can help you in the diassembling, assembling and in the transport ...

Material: mild steel Drive: 45 KW Weight: 2000 kg Dimensions: 1500 x 1500 x 1600 mm

Hammer muehle with blower, filler hopper and easily changeable sieves for the wuenschte fineness of the grinding material. Hammermuehle KH3 11 kW

- for grinding saemary cereals different models: Hammermuehle KH1 - 5.5kW Hammermuehle KH2 - 7.5kW

-Blower hammer mill with 45 kW -Rotor should be prepared

Hammer mill Fa. Wery

attention! To participate in this auction, a deposit of € 25 is required, which will be withheld until the outcome of the contradictory verification of the state of the places and the prior deposition of safety documentation that can be consulted after the signing of an NDA. The deposit is to be paid by bank transfer to the current account in the name of Surplex Srl. To request further information: m.tosin@tbauctions.com Lot consisting of various construction equipment, including DEWALT hammer drill, HILTI hose, HILTI rotary hammer, various pallet trucks. The list drawn up by the expert is attached to this announcement. The lot includes the following works that must be carried out in this time order no later than 30 days from the award. The total removal of the goods and correct disposal of the remaining NON-FERROUS materials after removal. The complete floor cleaning of the re ...

Rotary hammer, chisel hammer, combination hammer, Bosch hammer, impact drill, chisel hammer -Nominal consumption: 500 W -Drilling/hammer drilling -Speed: 0 - 2200 rpm -Dimensions: 290/80/H200 mm -Weight: 2.2 kg

Used hammer mill made by Alpine, type B 630. Manufacturer's documentation.

Hammer 16T-M2152-1pcs (136t) Hammer 10T-18KP-1pcs(104t) Hammer 5T-17KP- 1pcs (75ton) Hammer 3T-M213-1pcs(63T) Hammer 2T-M212-1pcs(40T)

Hammer Mill Manufactured by PESSA Model: MM-14R2000 Complete with main motor of 250 KW

Air demolition hammer -Operating pressure: 7 bar -Number: 1x demolition hammer available -Dimensions: 500/220/H70 mm -Weight: 6kg

Pneumatic demolition hammer, single-arm hammer, pneumatic hammer, jackhammer, chisel hammer -Number: 3x demolition hammer available -Price: per piece -Dimensions: 360/220/H80 mm -Weight: 6 kg

Compressed air demolition hammer -Operating pressure: 7 bar -Number: 1x demolition hammer available -Price: per piece -Dimensions: 640/365/H125 mm -Weight: 22 kg

Rotary hammer, chisel hammer, combination hammer, Bosch hammer -Drilling/Chiseling -SDS Plus: Recording -Transport case -Weight: 5 kg

HEBÖ LH50 power hammer was built in 2014 in Germany by hebö Maschinenfabrik GmbH. The machine is practically unused and fully operational. It was started up only for the purpose of testing, during which single workpieces were produced. The HEBÖ LH50 is a professional power hammer designed for hot metal forming in forges and workshops specialising in metalworking. It enables precise shaping of metal using powerful, repeatable hits, making it ideal for the production of, among others, ornamental bars and decoration elements. The impact strength of 50 kg is fully adjustable by the ergonomic foot pedal. The machine is also equipped with dies and a Vulcan plate. The HEBÖ LH-50 pneumatic forging hammer weighs 1150 kg. Technical specifications of the HEBÖ LH50 pneumatic power hammer - nominal dropping weight: 50 kg - number of hits: 220/min - hit stroke: 230 mm - Vulcan plate -  ...

Hydraulic hammer / hydraulic-Meisel attachment used. For bobcat, mini excavator and small wheel loader with holder on fork carrier. Manufacturer/Type: unknown Holder approx. H-400 mm, W-1114 mm Meisel-A approx. 70 mm Meisel length approx. 400 mm Pressure: 400/850 PSI Total approx. 1160 x 1000 x 800 mm Subject to changes and errors in the technical data, dates and prices as well as intermediate sale.

Working condition unprecedented. Auction-ID: A3-46141-4150

BHR Hydraulic Hammer for 0.8 to 2 Ton Mini Excavator Auction-ID: A3-46141-30337

A single-blow PS hammer produces a high impact force thanks to a single blow between the inner piston and the metal base welded to the walls of silos and hoppers. This action is effective when moving powder, which tends to compact under pressure or stick to walls, as well as most granular materials and bulk materials. For this reason, the PS series is the ideal solution for bridge and rat hole problems. Technical data sheet: Compact design with integrated valve. Outstanding performance Easy installation Suitable for operation in hazardous areas Discontinuous duty cycle Noise level 125 dB Temperature -20 °C / 80 °C Operating pressure: 3-6 bar (44-87 PSI). Direct effect on the product. It does not create tension in the structure.

21033665 Offer includes 1 piece, the other items visible in the photos are not part of the offer Auction-ID: A7-51314-205