128,994 used machines on RESALE, but how to find them? Machine Search
bore capacity in steel (diameter): 25 mm throat: 240 mm bore stroke: 110 mm turning speeds: 125 - 2850 U/min : 310 x 320 mm distance drilling head - clamping area: max. 650 mm total power requirement: 0,75 / 400 kW / Volt weight of the machine ca.: 0,175 t dimensions: 0,95x0,8x1,75 inkl. Tisch m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore capacity in steel (diameter): 40 mm throat: 370 mm bore stroke: 200 mm spindle taper MT: 4 MK table:: 580 x 460 mm column diameter: 160 mm turning speeds: 75 - 2020 U/min feeds: 0,1 - 0,2 - 0,3 - 0,4 mm/U total power requirement: 1,5 kW weight of the machine ca.: 700 kg. range L-W-H: 1,1 x 0,6 x 2,35 mm • machine base for clamping high workpieces • Digital Depth Gauge • Gearbox swivels 180 ° • silent running through geärtete, ground oil-cooled gears • Tapping Function • electromagnetic clutch for drill feed • automatic feed • electric drive for table height adjustment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 1000 mm y-travel: 300 mm z-travel: 400 mm table-size: 1320 x 360 mm spindle taper ISO: 40 spindle turning speed range: 58 - 1800 U/min total power requirement: 4 kW weight of the machine ca.: 2,3 t dimensions of the machine ca.: 2,1 x 2,1 x 1,95 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
capacity 90 degrees: round: 510 mm capacity 90 degrees: square: 480 mm : 610 x 450 saw band length: 5320 x 34 x 1,1 mm band speed: 15 - 100 m/min table height: 820 mm total power requirement: 3,0 kW weight of the machine ca.: 2,3 t dimensions of the machine ca.: 2,65 x 2,8 x 2,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Press force max.:: 1.000 kN heating plates:: 500 x 500 mm electrically heated:: °C heating power:: kW piston stroke:: ca. 500 mm no. of stages:: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cross-section width:: -- mm cross-section heigth:: -- mm feed:: -- mm speed of feed:: 0,4 - 20 m/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
We sell 1 x IBM DS8910, 5333-994 disk storage system In most cases, the entire lot can only be handed over in its entirety. More information on request. In most cases, advertised products can only be sold as a complete lot. More information on request. We look forward to receiving inquiries from Germany and internationally. We have many more refurbished/used hardware from the areas of the systems mentioned here as well as from the areas of other systems from these manufacturers available: IBM, DELL, HPE, ORACLE, NETAPP, QUANTUM, STK, FUJITSU, SGI, HDS, EMC, Supermicro, BULL, NEC, CRAY, 3Com, ADVA, Alcatel, Brocade, Cisco, Enterasys, Extreme Networks, Huawei, Marconi, Nortel, Qlogic, Avaya, ORACLE Tested, tested used hardware at low prices from HASCON! Sales are only made to companies. We have available complete systems and components in refurbished conditions from all ...
The machine is in good technical condition, after prior agreement possible to test. Control system – Siemens Including filtration. Bed inclination Bed material Number of guides 45 cast iron 3 (4 with Y-axis option) WORKING SPACE (V1- V4) Swing diameter over bed inch 19.69 Swing diameter over cross slide inch 11.42 Largest turning diameter inch 7.87 200 ч Distance between centers inch 30.71 Largest turning length inch 19.69 15.82 20 Max. weight of flying unsupported part of workpiece lb 35 Max. distance of center of gravity of flying unsupported part of workpiece inch 165 from spindle face Max. workpiece weight clamped between centers lb 100 X-axis travel length inches 7.48 Y-axis travel length (OР.) inches 3.14 (+/- 1.57) Z1-axis travel length inches Z3-axis travel length inches Spindle axis height above floor inches 20.67 21.65 39.26 (38.77+1.18) MAIN SPINDLE Spindle face (flat face ...
round bar steel: 45 mm square edge steel: 42 mm L-beam: 140 x 13 mm flat steel: 350 x 20 mm pressure: 550 kN throat: 305 mm notching: rectangle tool: mm total power requirement: 5,5 kW weight of the machine ca.: 1260 kg dimensions of the machine ca.: 1360 x 750 x 1565 mm 2 working cylinder with 2 separated electric foot switch for 2-people-handling New notching table, new knife for the rectangle notcher and new punching table included For further information please see brochure. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
container volume: 600 l internal dimension: 1500 x 740 x 780 mm dimensions of the machine ca.: 1900 x 810 x 860 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
faceplate diameter: 510 mm max. pitch circle: 171,4 mm camlock: Gr. 8 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 550 mm y-travel: 1200 mm z-travel: 450 mm control: 85er 8bit total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 3.400 mm y-travel: 1.250 mm z-travel: 2.000 mm Control: TNC-430PA table-size: 4.700 X 1.200 mm V- travel: 500 tool taper: ISO 50 milling head -swivable: 0.001º/0.001º Grad main drive: 37 kW Chip coveyor: inkl handwheel: HR-410 Tools changer: 60 pos. milling head: Automatic Head 45º weight of the machine ca.: 35 t - Automatic Head 45º INCLUDED - Automatic Head 45º 0.001º/0.001º - Head 45º Max. Speed 3.000 rpm - 45º Head Taper ISO-50 - Twist Head Contiuous INCLUDED - Twist Head Max Speed 3.000 rpm - Twist Head Taper ISO-50 - Ram with Quill - Quill Diameter 150 mm. - Quill Taper ISO-50 - Pick up station AITEK for 45º and Twist Heads - Rotary Table ZEATZ Ø 1200 INCLUDED - RENISHAW MP 16+SP2/1 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
With matching spacer rings according to photos. Scope of delivery according to photo 1.
The container has two saddle feet, a manhole DN 600 with dome lid, is used and emptied inside and professionally cleaned. Dimensions: D = 2.50 m - L = approx. 10.70 m On request, the container can be completely equipped with an extinguishing water suction connection: Extinguishing water suction connection / suction line made of stainless steel V2A - consisting of: - 1 suction line DN 125 with A-fixed coupling according to DIN 14319 with special closure for fire brigade tricant keys incl. a ball valve 4", - 1 pcs. sleeve incl. ball valve welded into the highest point of the suction line (for ventilation of the suction line), - 1 pc anti-vortex plate mounted on suction line, - 1 pc sign "Extinguishing water extraction point", - 1 pc vent pipe DN100 with hood, - 1 pc bearing tube with dipstick for measuring the level, - 1 pc dome lid with screws an ...
x-travel: 3500 mm y-travel: 900 mm z-travel: 1000 mm Control: heidenhain tnc 415B total power requirement: 22 /spindel kW weight of the machine ca.: 16.5 t dimensions of the machine ca.: 7.2x3.9x3.2 m Make SORALUCE Type Soramill SL 5000 Built in 1995 Control type HEIDENHAIN TNC 415 B Table size (mm) 5000 x 800 mm X out (mm) 3500 Y-off (mm) 900 Z-off (mm) 1000 Maximum table load 12,5 ton Speed (RPM) 20-. 2,000 Tool holder ISO 50 Feed along (mm/Rev) 5 - 10000 mm / min. Rapid traverse 12 mtr/min. Gesamtleistung(kW) 22 Length (mm) 7250 Width (mm) 3900 Height (mm) 3200 Weight 16500 kg Additional information Automatically indexierender Swivel Head with 2 x 144 positions (2.5 ° pitch) in two levels above the control programmable Cooling medium institution The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
; Gross weight [kg]: 4950; Engine: Cummins QSZ13-G3; Accessories: Tanker, Battery, Control Panel, Stahldach, Including: Coolant Heater and Battery Charger; Water Tank Volume [l]: 775
X-axis: 13,000 mm Y-axis: 4,500 mm Z-axis: 1,000 mm Distance between stand: 6,500 mm C-axis: 190º A-axis: 110º Rapid speed XYZ: 15,000 mm/min. Rapid response AC: 10 tpm CNC control: Siemens 840D Spindle mounting: HSK A63 Spindle speeds: 30,000 rpm. Spindle power: 20 kW Tool changer: 20 positions Torrestool tables: 16 pieces X-axis: 11,500 mm Y-axis: 3,500 mm Z-axis: 750 mm Country of origin Spain Machine dimensions LxWxH: 19,000 x 11,000 x 6770 mm Machine weight: 70,000 kg
; Gross weight [kg]: 4100; Engine: Volvo TAD1345GE; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 515
Instrument for gas chromatography AGILENT mod. GC/ MS 7890/5975 Including: Agilent 7890GC Agilent 5975 C MSD EI Source and Diffusion pump Injector Tray etc. Refubished
roll diameter: 560 mm roll length: 1500 mm rolls drilled: Peripher Nip adjustment: hyraulisch 0 total power requirement: 150 kW Condition: used, completely overhauled, with warranty Specification: rolling mill 560 x 1500 mm - used model external gearbox - motor sideways placed at the machine - roll diameter: 560 mm - roll length: 1500 mm - model: Duplocom / pluridrive - Peripherally drilled rollers for water cooling - Cardan joints between gearbox and rollers - Individual drive for the rollers, for variable friction - hydr. gap adjustment - Hydraulic unit - Tilting steel guide plates - rollers mounted on roller bearings with appropriate lubrication - rollers with new ball bearing slewing rings, make Maier, for the connection to the water circuit - One gearbox - two individual drives, each with: 2x 75 kW - 400 V - 50 Hz - two new frequency conv ...
Air compressor Planet Air L 550 with dryer KT 700; good condition; 550L/min.; 10 bar; incl. air dryer KT 700. Compressor Plant AIr AL 550; good condition; volume 550L/min.; 10 bar; with air dryer.
SCHRÖDER DM-500 ID.NO. 2117 Schröder DM-500 brine mixer with mixer and pusher that goes up and down. Dimensions 135 x 135 cm H 180 cm. Available 4x in stock.
turning diameter: 570 mm turning length: 1000 mm control: Sinumerik 805 Siemens clamping length: ca 1200 mm greates pass round over bed: 570 mm swing diameter over face slide: 365 mm turning speed range - main spindle: 3 - 2.500 min/-1 power capacity - main spindel: 15 / 19 kW spindle bore: 62 mm spindle head: DIN 55027 No. 8 diameter of quill: 80 mm taper of center: MK 5 quill stroke: 190 mm total power requirement: 40 kVA weight of the machine ca.: 5,6 t Lathe cycle controled - SIEMENS Sinumerik 805 / Simeodrive 611 - 4-Jaw Chuck, Handwheel, Covering - Chip Tray & coolant - adjustable feet - approx 20 tool holders 2021 Electrics/controls check by Boehringer The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Key data: 520 , 7
Holzkraft SCM thickness planer S 52ES Product name: Thickness planer Model: S 52ES Type: SP-03 Manufacturer: SCM (SCM Industria S.p.A.) Machine number: KK00019806 Year of construction: 2021 Condition: as good as new technical details: - Work table size: 850 x 520 mm - Useful width: 520 mm - max. chip removal per operation: 5 mm - Knife shaft diameter: 120 mm - Number of knives: 30x3x520 / 4 pieces - Knife shaft speed: 5,200 rpm - Holding time knife shaft: less than 10 sec - Feed speed during thickness planing: 5 - 8 - 12 - 18 m/min - Diameter of the extraction hood (plastic): 120 mm - required speed of the extraction air: dry chips = 20 m/sec, wet chips = 28 m/sec - Consumption of extraction air [diameter 120 mm]: 814 m³/h dry chips, 1,140 m³/h wet chips workpiece height: 240 mm workpiece width: 520 mm - min. workpiece height: 3.0 mm - min. workpiece length: ...
Moog Servo Valve Unit D665-5703 & D661-5623C High Performance Valve Module For sale is a fully functional, industrially used high-performance servo valve unit from MOOG, consisting of two perfectly matched valves Also available as a single component ! Moog D661-5623C – High-Response Valve Technical Property Value Model name: D661-5623C Type code G18H0A0NSA0HP Valve type 4-way, 2-stage with bushing slider Nominal volume flow 120–200 l/min (depending on version) Operating pressure P, A, B max. 350 bar Return pressure T (internal) 210 bar Return pressure T (external) 280 bar Control pressure 25–350 bar Coil stroke ±0.13 mm Control surface (AK) 1.35 cm² Actuation time (0–100 %) approx. 14 ms Hysteresis < 0.6% Zero displacement < 1% Supply voltage ±15 V DC Input signal ±10 V IP65 protection Mass approx. 5.7 kg Connection diagram ISO 4401-05-05-0-94 ...
; Gross weight [kg]: 4600; Engine: Hyundai DP158LC; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 775
ACCUTEX AU-500iA wire EDM was built in 2007 in Taiwan by ACCUTEX TECHNOLOGIES CO., LTD. The machine uses advanced electrical erosion technology for precise, 5-axis machining of workpieces with a maximum weight of 400 kg. This method enables difficult shapes to be achieved in even the hardest materials. The need for other secondary processes, such as polishing, is also minimised or completely eliminated. All this makes the offered AU-500iA wire EDM machine the best choice for the production of e.g. dies, tools and punches. The total weight of the machine is approximately 3500 kg. Technical specifications of the ACCUTEX AU-500iA wire EDM - CNC controller - number of axes: 5 (X,Y,Z,U,V) - feed in the X/Y/Z axis: 500/300/300 mm - feed in the U/V axis: 100/100 mm - maximum workpiece weight: 400 kg - maximum workpiece dimensions (L x W x H): 990 x 560 x 295 mm - cutting angle: ±22.5 ...
Inlet opening: approx. 500 x 1000 mm Rotor width: approx. 1000 mm Rotor diameter: approx. 500 mm Stator knives: 3 Rotor blade: 6 x 3 With base frame Feed opening: approx. 500 x 1000 mm Rotor width: approx. 1000 mm Rotor diameter: approx. 500 mm Stator knives: 3 Rotor knives: 6 x 3 With base frame
SAKURAI 572 EDII + C Year of manufacture: 2003 Number of Units: 5 + C Number of Impressions: c.85 Million SCC II off press controls with overhead lamp Olivermatic dampening with Technotrans Alpha c recirculation SPC semi-automatic plate change with cylinder cocking Eltra combi Automatic Blanket & Impression Cylinder Double Sized Impression / Transfer Cylinders Ink Roller cleaning Presets Suction belt infeed Anilox coating unit with extended delivery Harris & Bruno coating system Grafix IR/hot air end of press dryer Grafix anti-set-off spray.
core engine Centaur 50. The turbine and associated gearbox have been completely base overhauled after last operating and are a ready-to-install for a zero-hour turbine exchange. After the overhaul, there was no active operation / no installation. The turbine and gear box Sale Solar Centaur 50 Base overhauled core engine: Manufacturer Solar Turbines - Type CENTAUR 50 SoLoNox - Year of construction 2022 Zero-hour core turbine and gearbox - Electrical output 4,040 kWel - Speed 14,944 rpm 50Hz - Fuel Natural gas H - Design temperature 15° C - Turbine inlet temperature 665 °C (1.229 °F) - Gearbox with zero operating hours - Turbine control Solar TTS4
5.50 Meters AR Racking Pallet Rack AR Racking pallet racking with a total length of 5500 mm, consisting of a base field and an attachment field (2700 mm each). Each field has three levels (including floor space) with four trusses (2700 mm). 3 Euro pallets can be stored next to each other and 3 pallets (incl. floor space) on top of each other per field One field offers space for 9 Euro pallets Manufacturer: AR Racking Type: ARPA-S Total length: approx. 5500 mm Shelf height: 3000 mm Shelf depth: 1100 mm Clear field width: 2700 mm Pitch: 50 mm Number of storage levels: 3 (incl. floor storage space) Number of fields: 2 Shelf load: 3,000 kg Bay load: 6,000 kg Pallet spaces: 18 Year of manufacture: 2023 Stand The frames consist of two Omega profiles with their corresponding connectors, post feet and fastening materials The horizontal and diagonal struts are ...
Precision ball screw drive, KGT 50mm, Gewindelg 2670mm, Rexroth, new Special price If you have a VAT number, we will gladly issue you an invoice without VAT. Mint condition in original packaging! The part was purchased from a spare parts warehouse of a company and has never been in operation, is in a completely mint condition and in its original packaging. - Precision ball screw /ball screw with nut - Thread nominal diameter 50mm, pitch 10mm, 4 turns, that means 40mm travel per turn of the nut, - Total length: 2930mm, - ball screw length: 2670mm Shaft end 1: 165mm lg - D32 x 35mm lg, thread M35 x 1,5 x 25mm lg, D35 x 85mm lg, D42 x 20mm lg Shaft end 2: 95mm lg - thread M25 x 1,5 x 28mm lg, D35 x 53mm lg, D42 x 14mm lg Function guarantee! For second hand parts, we can not provide a conventional warranty and guarantee. However, we give you a functional guarante ...
Type: S 500 l 2P-V Complete stainless steel Hopper capacity 500 liter Double working shafts Rotation of shafts in both directions Vacuum: 0,04 – 0,06 mpa Electric power: 5.6 kW Voltage: 380 V / 50 Hz Discharging pneumatic flaps PLC + Touchscreen control Delay start 99 programs Installation dimensions of the machine in cm: Width: 160 Lenght: 95 Height: 142 Delivery time: after advanced payment, one working day
Bakon cream blower Type: Top Cream 530 Year of construction: 2011 Stainless steel digital control Temperature indicators 1.5kW As good as new condition Height: 115cm Width: 50cm Depth: 64cm
Size: max 500 x 330 mm min 140 x 150 mm Product thickness: 4-96 pages Speed: max 100.000 Ex./h Pile height 300 mm Infeed height 500-1920 mm Delivery height 890 mm
Block glue press Müro 5000/A2 WT; Working width 705mm; 3x dryer; Stack increase; heat deflector; Stand-standing device. Padding press Müro 5000/A2 WT; working width 705mm; 3x dryer; pile elevation; heating sheet; floor mounted machine.
20 station collating, 1 x VAC 100a, 1 x VAC 100m, 1 x Stacker ST-40, 1 x folder ACF-30, 1 x Stitcher SPF 30, 1 x Three knife trimmer HT 330
Winterhalter GS 502 Basket Push-Through Machine The Winterhalter GS 502 rack pass-through machine offers you all the necessary basic features that a rack pass-through dishwasher must have. You benefit from a consistent hygiene concept with a deep-drawn tank, surface radiator and screening system. Thanks to the concentrated cleaning power, Winterhalter guarantees hygienically clean washing results, even with heavy soiling. Specifications: Theoretical power: 60 baskets per hour Dimensions (width x depth x height): 635 x 749 x 1469 (canopy open 1932) mm Entry height: 420 ± 5 mm Working height: 850 mm Basket dimensions: 500 x 500 mm Fuel tank capacity: 42 l Rinsing water requirement per wash cycle: 2.4 l Tank temperature: 60°C Boiler temperature: 85°C Required water flow pressure: 1 bar Total connected load with hot water connection > 40°C: 9.5 kW Total connected lo ...
PART NUMBER 7794 SPECIFICATIONS - inlet width 530mm - inlet height 200mm - shaft diameter 370mm - shaft width 510mm - knife length 510mm - number of knives 2pcs - autorever – adjustable - sieve dimensions 50x50mm - Bottom geared pulling shaft 1.5kW - Toothed pulling shaft from above 1.5kW - main motor power 30kW - vibroline loading table / vibroline length 3900mm - vibroline width 500mm 1.5kW - Receiving conveyor belt length 5000mm - tape width 380mm - hopper with chute for sprues 2500x3020x2200mm - Platform 4650x750x1770mm - Dimensions of the machine with conveyor belt and vibroline length/width/height 8900x1200x2550mm - weight about 6000kg ADVANTAGES – adjustable autorever – with vibroline 3900mm – with conveyor belt 5000mm – German production – very good condition – used chipper Net price: 98900 PLN Net price: 23548 EUR depending on the pr ...
With new 1.500mm. wide belt and new control-unit. Will be overhauled, sandblasted and painted.
Maximum pressure: 54 tons Pressing force: 5.62 kg/cm² Bale size: 1200x800x1200 mm Bale weight: approx. 500 kg Power supply: 400V / 4 kW Year of construction: 1999, 2000 Productivity: approx. 2 bales/hour Price: on request Machine is fully functional, after technical inspection. We have several channel balers and balers in our warehouse and we cordially invite you to contact us!
Submersible pump, 250 L/min, 27 m, STA404/500-GX+121, Brinkmann Pumps, mint condition Special price If you have a VAT number, we will gladly issue you an invoice without VAT. As good as new! The pump was purchased from a company's spare parts warehouse, was in its original packaging, has never been used and is completely new. Submersible pump, 250 L/min, 27 m, STA404/500-GX+121, Brinkmann Pumps, as good as new, Immersion depth 500 m, Connection flange AD 180 mm, TK160 mm z=4, required opening for cover D140 mm, IP55, 2.6 KW, 230/400 V Special design: Base cover and impeller made of grey cast iron, shaft made of stainless steel 1.4104 6 months warranty We give you 6 months warranty for these goods from the date of invoice. In case of any defect, which is not the fault of the buyer, the goods can be returned. We will refund the buyer only the product price paid to us. ...
clamping force: 500 kN injection volume: -- cm³ screw diameter: 25 mm platen size: 400 x 400 mm Condition: used, Specification: horizontal injection molding machine, - used injection unit: - Screw diameter: 25 mm - shot volume max.: -- cm³ - injection pressure approx.: 1290 bar - heating zones: 4 - Heating power: 4 kW clamping unit: - clamping force: 500 kN - opening stroke max.: 325 mm - platen distance max.: 550 mm - clamping platen size approx.: 400 x 400 mm - tie bar distance: 270 x 270 mm - pump motor: 15 kW - total power: 19 kW - operating voltage: 380V, 50Hz - Weight approx.: 1.870 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
High-pressure tube fan made of aluminium, AD710mm, TDE 500 D4, Ruck, used Special price If you have a VAT number, we will gladly issue you an invoice without VAT. Used part! The part was purchased from a spare parts warehouse of a company, is in a very good condition and fully functional. High-pressure tube fan, diagonal impeller ventilation fan, TDE 500 D4, Ruck, up to 9880m³/h, 3.3 KW, 400 V, do not operate without FIS! Aluminium design, AD 710mm, L730mm, incl. industrial plug Ensuring the function In order to ensure the functionality of the goods, the buyer must check the goods at the time of acceptance or put them into operation. In case of any defect, which is not the fault of the buyer, the goods can be returned within 2 weeks. We will refund the buyer only the product price paid to us. For these goods we have to exclude warranty claims of the buyer for improve ...
maximum number of results exceeded
please refine your search
