edge used for sale

: 0,4-5 mm Workingpiece thickness from to: 6-45 mm Total length: 4130 mm Feed speed: 11 m/min. total power requirement: kw Weight: 1250 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 0,4-3 mm Workingpiece thickness from to: 6-45 mm Total length: 3700 mm Feed speed: 8 m/min. total power requirement: kw Weight: 900 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Workpiece thickness: 8 - 50 mm Edge thickness: Coil edges 0.4 - 3 mm Feed speed 10 m/min Equipment: manual height adjustment. Joint milling unit, 2 motors Panel edge heating Gluing area Pressure zone 1 driven and 2 non-driven rollers End trims, 2 x 0,8 kW motors, straight and chamfer 15? Top and bottom trimming Profile scraping unit for PVC edging Glue scrapers

Workpiece thickness: 8 - 60 mm Workpiece overhang: 38 mm Edge material of the roll: 0.4 - 3 mm Edge material in strips: 0.4 - 6 mm. Min. workpiece width: 70 mm (with thickness 8-22 mm), 120 mm (with thickness 23-40 mm), 150 mm (with thickness 41-60 mm) Feed speed: 11 m/min Machine equipment: Joint milling unit, 2 x 2.2 kW motor Gluing unit with workpiece edge preheating Pressure zone with driven main pressure roller and 2 non-driven pressure rollers Hood unit, 2 x 0.18 kW, pneumatic adjustment phase/straight Radius and fine milling unit, 2 x 0.27 kW Form milling unit 1 x 0.35 kW Profile scrapers Glue joint scrapers

Panel thickness: 8 - 50 mm Thickness of the edges: 0,4- 3 mm Feed speed 8 - 11 m / min PU pressure rollers Equipment: Squaring unit, 2 motors 2,2 kW Panel edge heating Edge magazine for coil and strips Hot melt application with roller Airtec AT4510 unit The Airtec aggregate is positioned so you can use Airtec or the standard glue pot Motorized side pressure unit End trims, 2 motors, pneumatic positioning straight and with chamfer trimming unit above / below Contour trimming unit Profile scraping unit Glue scraping unit Polishing unit Detergent spray system central lubrication

Fixed side at the left Feedspeed 18 - 25 m/min Working width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mm Panel overhang 30mm Panel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations) Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mm Coil diameter 830 mm Equipment: Sprayers release agent Squaring device with 2 motors each 3 kW Edge heating Edge magazine for 2 coils, guillotine for edges up to 3 mm Glueing part A20 with quickmelt application Lateral pressure zone K, 1 driven and 6 after pressing rollers End trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kW Contour trimming, 2 exchange units Profile scraping PN10 Flat scrapers FA11 Sprayers cleaning agent Buffing Automation package straight/chamfer: -Automatic adjustment infeed fence -Automatic setting of pressure rollers -Pneumatic setting of end trims -Pneumatic setting of rough trims -Automa ...

Single sided edge bander with hot melt, fixed side at the right, pre-milling unit Edge thickness: 0,4 to 12 mm Workpiece thickness: 8 - 60 mm Feedspeed 8-20 m/min (limited to 10 m/min using the contour trimming) Workpiece transport by chain, top pressures with rubber rollers Sound enclosure over all trimming motors Equipment: Adjustable fence Pre-milling with 2 shapers, each 2,2 kW Coil and strip magazine Hot melt unit, Quickmelt type Pressure zone with1 driven and 2 non-driven pneum. Loaded rollers End trims, 2 x 0,35 kW motors, straight and chamfer 15? Top/bottom trimming, motors 2 x 0,35 kW Radius trimmming Contour trimming unit, leading and following edge, 2 x 0,35 kW Radius scraping unit Glue scrapers Buffing unit Controlls PC 20+

Fixed side at the left Feedspeed 18 - 25 m/min Working width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mm Panel overhang 30mm Panel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations) Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mm Coil diameter 830 mm Equipment: Sprayers release agent Squaring device with 2 motors each 3 kW Edge heating Edge magazine for 2 coils, guillotine for edges up to 3 mm Glueing part A20 with quickmelt application Lateral pressure zone K, 1 driven and 6 after pressing rollers End trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kW Contour trimming, 2 exchange units Profile scraping PN10 Flat scrapers FA11 Sprayers cleaning agent Buffing Automation package straight/chamfer: -Automatic adjustment infeed fence -Automatic setting of pressure rollers -Pneumatic setting of end trims -Pneumatic setting of rough trims -Automa ...

Workpiece thickness: 8 - 90 mm, electronically adjustable Feed rate: 18-32 m/min frequency controlled Edge thickness: 0.3 - 3 mm for roll edges, strips up to 20 mm Equipment: Inlet guide automatically adjustable via the control, extension 500 mm Joint milling unit: 2 x 3.0 KW workpiece preheating Gluing unit A34 edging magazine for roll Pressure zone with 1 driven, 6 non-driven rollers, automatic adjustment from the control Cutting unit WK14, straight, 2 motors 0.8 kW Pre-milling unit: 2 x 1.5 KW, pneumatic adjustment Form milling unit FF 12 automatic, 2 motors 0.4 kW radius/phase milling unit FF12 automatic 4 motors 0.4 KW universal milling aggregate controlled UF11, 4 kW Profile scrapers PN20 Glue scrapers Nozzles for detergent and anti-stick Polishing unit Control: Power Control PC22

Panel return system for single-sided edging machine in left-hand version with a length of approx. 12m50 Panel length 240 to 2700 mm Panel width 60 to 1000 mm Panel thickness 8 to 80 mm Min/max panel dimensions with 4-sided machining: 240 x 80 mm, 2500 x 1000 mm Working height 950 mm At the machine outlet is a tilting air table that returns the workpieces on a conveyor belt to the machine operator Tilting air table with dimensions 2500 x 1400 mm Air table at the front of the machine inlet with dimensions 720 x 580 mm Brush cleaning of the return belt air table at the end of the return conveyor with dimensions 2500 x 1250 mm

Tape dimensions 150 x 2,260 mm Belt speed 17m/sec Connection 400V, 3~, 50 Hz, 2.5A, 1.5 kW Weight approx. 120 kg

Equipment: - Joining milling unit - Gluing part with pressure zone - Cross-cut unit - Radius/chamfer/flush milling machine - Shape milling unit (2-motor) - Profile scraper blade - Wing scraper blade - Buffing unit - Release agent spray unit - Detergent spray unit Technical data: Workpiece: Workpiece thickness min. 8 mm (or 12 mm with profile scraper), max. 60 mm Workpiece length min. 150 mm Workpiece width min. 150/65 mm with workpiece thickness 25 mm Smallest workpiece 65 x 300 mm / 150 x 300 x 19 mm Edge material: Edge thickness 0.3 - 3 mm Edge height 12 - 65 mm Edge length min. 200 mm Max. edge cross-section: Roll 150 - 180 mm, strip 480 mm Machine data: Length 6,630 mm Width 2,050 mm (hoods open) Height 1,700 mm (hoods closed) Min. distance to the wall: 1,000 mm (aggregate side) Weight: approx. 3000 kg Upper edge of chain conveyor 900-930 mm Workpiec ...

: 0,4-8 mm Workingpiece thickness from to: 8-60 mm Total length: 4930 mm Feed speed: 10 m/min. total power requirement: kw Weight: 1500 kg Control: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Edge banding machine Type: PROFIMATIC PM 2508-F Manufacturer: OTT Year: 2005 Hours: approx 300 Edge thickness: 0.220 mm Min width of the working part: 70 mm Min height of the working part: 8 mm Max height of the working part: 60 mm Min length of part: 150 mm Operating voltage: 400 V / 50 Hz Continuous speed: 1020 m/min Adhesive application: glue application cylinder with Vario Melt automatic dosing Working height: 880 mm Compressed air connection: 6 bar / 1/4 Dimensions: 8850 x 1250 x 1500 mm Weight: 4,000 kg Machine in good condition, fully functional, under power Find more here - .ucymachines/ Contact us at - sales@ucymachines

IMA COMBIMA K/II/R75/760/V/R3 edge banding machine was built in 2000 in Germany by IMA-Maschinenfabriken Klessmann GmbH. The machine is used in woodworking workshops and furniture manufacturing companies, where it is used for the precise edge-banding of components made from chipboard, MDF and laminated materials. The durable bond between the board edge and the edging contributes to the aesthetic appearance of the finished components, whilst also increasing their resistance to mechanical damage and moisture. The edge banding process begins with heating the adhesive to the correct temperature, and then applying it evenly to the edge of the board. At the same time, the edging is precisely pressed against the surface with rollers. Maintaining the correct temperature and constant pressure ensures the adhesive bonds evenly along the entire length of the component, guaranteeing a high-qualit ...

With mobile 6-fold edge band infeed unit, touchscreen control panel, air roller table size 960x1960mm, built-on roller table width 1100mm, Combined belt conveyor size 3300x1400mm, belt conveyor size 3200x900mm, belt conveyor 6200x900mm and driven roller conveyor with cross transport size 2100x1030mm Auction-ID: A1-48377-7

Tilting axle braked up to 45 degrees. On a pallet. Auction-ID: A1-49727-10

With a Holz-her power supply. On a pallet. Auction-ID: A1-49727-7

Model: SE33.3K OUTPUT (AC) Rated AC power: 33 300 W Maximum AC power: 33 300 VA Rated AC voltage (phase-to-phase / phase-neutral): 380 / 220 V – 400 / 230 V AC voltage range (phase-to-phase / phase-neutral): 304–437 V / 176–253 V and 320–460 V / 184–264.5 V AC frequency: 50 / 60 Hz ±5 % Max Continuous AC Current (per phase): 48.25 A AC Line Connection: 3W+PE, 4W+PE Emission monitoring, anti-islanding protection, power factor and configurable thresholds per country: yes Total harmonic distortion: <3 % Power Factor Range: +/−0.8 to 1 Maximum residual current: 100 mA INPUT (DC) Maximum DC Power (STC Module): 58 275 W Transformerless, ungrounded – yes Max DC+ input voltage: 1 000 V DC input voltage rating: 750V Max Input Current: 48.25A Reverse polarity protection: Yes Ground insulation detection: 150 kΩ sensitivity Maximum inverter efficiency: 98.3 % ...

On a pallet. Univer 508 feeder. Auction-ID: A1-49727-23

Table size 3550x1850mm, with various vacuum machine tooling and central touchscreen control Auction-ID: A1-48377-6

Felder FS900K edge grinder Sanding belt width 150 mm 45 tilt worktop Sanding belt oscillation Motor power 3kw Year of manufacture 1996 Machine dimensions 147x61x121cmH

Model: SE33.3K OUTPUT (AC) Rated AC power: 33 300 W Maximum AC power: 33 300 VA Rated AC voltage (phase-to-phase / phase-neutral): 380 / 220 V – 400 / 230 V AC voltage range (phase-to-phase / phase-neutral): 304–437 V / 176–253 V and 320–460 V / 184–264.5 V AC frequency: 50 / 60 Hz ±5 % Max Continuous AC Current (per phase): 48.25 A AC Line Connection: 3W+PE, 4W+PE Emission monitoring, anti-islanding protection, power factor and configurable thresholds per country: yes Total harmonic distortion: <3 % Power Factor Range: +/−0.8 to 1 Maximum residual current: 100 mA INPUT (DC) Maximum DC Power (STC Module): 58 275 W Transformerless, ungrounded – yes Max DC+ input voltage: 1 000 V DC input voltage rating: 750V Max Input Current: 48.25A Reverse polarity protection: Yes Ground insulation detection: 150 kΩ sensitivity Maximum inverter efficiency: 98.3 % ...

Model: SE33.3K OUTPUT (AC) Rated AC power: 33 300 W Maximum AC power: 33 300 VA Rated AC voltage (phase-to-phase / phase-neutral): 380 / 220 V – 400 / 230 V AC voltage range (phase-to-phase / phase-neutral): 304–437 V / 176–253 V and 320–460 V / 184–264.5 V AC frequency: 50 / 60 Hz ±5 % Max Continuous AC Current (per phase): 48.25 A AC Line Connection: 3W+PE, 4W+PE Emission monitoring, anti-islanding protection, power factor and configurable thresholds per country: yes Total harmonic distortion: <3 % Power Factor Range: +/−0.8 to 1 Maximum residual current: 100 mA INPUT (DC) Maximum DC Power (STC Module): 58 275 W Transformerless, ungrounded – yes Max DC+ input voltage: 1 000 V DC input voltage rating: 750V Max Input Current: 48.25A Reverse polarity protection: Yes Ground insulation detection: 150 kΩ sensitivity Maximum inverter efficiency: 98.3 % ...

With Format smartouch control panel, 3x air infeed table, 4-fold outfeed belt conveyor 2x various roller conveyors, 1x conveyor belt size 900x7000mm Auction-ID: A1-48377-5

With Format smartouch control panel, U-motion driven roller conveyor unit dimensions approximately 2050x2200mm, belt conveyor dimensions 880x4170mm and roller conveyor dimensions 890x1950mm Auction-ID: A1-48377-24

SCHALLBERGER FACETTESTAR machine for precision edge finishing, chamfering and deburring of tools or metal parts. This type of equipment is used in mechanical workshops to improve the quality of edges, reduce tool wear and ensure better service performance. The machine enables smooth, controlled and repeatable work, which is essential in precision applications. Ideal for: CNC machine shops Tool Manufacturing Precision mechanics Industrial production Technical maintenance Equipment sought after for finishing and edge preparation work. Auction-ID: A1-48554-20

With 10 cross beam fixtures each equipped with vacuum pads, machine tooling, 2x Becker vacuum pump, switch cabinet and central controller Auction-ID: A1-48377-10

Gebr. Edge grinding machine LANGZAUNER LZK 1/1 without oscillation YOC 1992 Motor power: 2.2 kW Rated current 5.0 A Strap length: 2,100 mm Belt height: 150 mm Table size: 80 x 30 cm Table height adjustment range: 20 cm Height adjustable support table  Integrated extraction fan Chassis Dimensions: 140 x 70 cm Very good original condition! The machine comes from a 1-man operation. Manufacturer information

FORD EDGE 20 TDCI 2017, super complete, entire maintenance history, 2 sets of wheels, just had a service. Auction-ID: A1-47415-175

⚠️ Important note: The machine requires an overhaul by a brand technician for installation. Spare parts are supplied with the machine. HOLZ-HER SPRINT 1312 Automatic banding machine with gluing, flushing, scrapers and polishing units. Control: EdgeControl with direct buttons Air pressure: 6–8 bar Voltage: 400 V Serial Number: 5010376 Accessories: glues, milling cutters, polish, hoses Dimensions (mm): 4300 × 1200 × 1600 Weight (kg) : 1000 Auction-ID: A1-49230-10

Technical details Manufacturer: Biesse Model: Akron 1440A Serial number: 1000050071 Type: Automatic edgebanding machine Configuration: - Automatic edgeband feeding from rolls and strips - NC-controlled automatic group adjustment - Automatic program selection and diagnostics - Production statistics and maintenance software - Feed speed: 12–18 m/min - Geared feed motor: 1.5 kW - Panel thickness: 10–60 mm - Edge thickness (rolls): 0.4–3 mm - Edge thickness (strips): 0.4–12 mm - Glue pot capacity: Approx. 2 kg - Glue heating time: Approx. 10 min - Working voltage: 400 V / 50 Hz / 3 Ph + N - Control voltage: 24 V DC Equipment: - Antistatic spraying unit - Pre-milling unit with 2 × 1.8 kW HF motors - Glue application and pressure unit - End trimming unit - Top/bottom trimming unit - Corner rounding unit - Radius scraping unit - Surface scraping unit - Text ...

Important Note: Machine needs a full overhaul by technician prior to installation. Otherwise will not work. Equipment type: Automatic edge banding machine for wood panels, continuous feed with electronic settings and multiple suction system. Manufacturer: CASADEI (SCM INDUSTRIA S.p.A.) Model: FLEXA 17 S Year: 2019 Serial Number: KK00002892 Technical description: The CASADEI FLEXA 17 S automatic banding machine is a machine designed for craftsmen and small and medium-sized companies, offering great ease of use without compromising on quality. Its robust frame and flexible units ensure excellent productivity and the possibility of carrying out any type of treatment on wood panels. Key features: • Panel thickness: 8 ÷ 50 mm • Band thickness: 0.4 ÷ 3 mm (5 mm opt.) • Edge thickness: 3 mm (5 mm opt.) • Feed speed: 7 m/min • Power supply: 400 V / 3 ph / 50 Hz  ...

4-roll 2000x6 mm plate bending machine Davi model MAX2017 year 2004 used plate roll in working condition, Planetary dual pre-pinch Performance Capacity: Plate width 2000 mm plate thickness 6 mm pre-bend 5 mm minimum rolling diameter ID 350 mm rollers length 2050 mm Upper roll 165 mm Pinch roll 155 mm Side rolls 120 mm Power electric motor 3 kw on hydraulic unit Vac 400/50 mm Installed configuration Rollers surface hardened high strength Conical plate rolling, cone bending Hydraulic commands via leverage distributors Infinitely variable speed control Digital position readout --- Hydraulic driven motorized the central rolls Pre-pinch pressure adjustable for pre-bend Drop-end front open to unload closed shells Re-rolling system for calibration of welded shell Safety and emergency stop machine dimension 3400x1150xH 1100 mm -weight 2200kg

: 0,4-6 mm Workingpiece thickness from to: 6-60 mm Total length: 3516 mm Feed speed: 10 m/min. total power requirement: kw Weight: 850 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

A total of 2 edge cutters with 3 brackets, 230V, max. 60Hz, 5A, 1050W, see photos for more details Auction-ID: A7-49942-1040

Landing surface: 50cm, see photos for more details Auction-ID: A7-49942-1041

Auction-ID: A1-40897-256

Edge banding machine Brandt Highflex KDF 220 with jointing, corner copying and two Scraper blades. Very well automated. A video of the running machine can be sent on request. Edge thickness roll approx. 0.4 - 3mm, solid edge up to 6mm Workpiece height approx. 10 - 60mm Feed speed approx. 10m/min Noise protection hood Pull-out workpiece support Suction connection 1x120mm, 1x100mm, 3x80mm Easy-touch EC+ control for easy operation of the machine 4 programs can be saved. Machine in high-flex design, highly automated, change of edge from thin edge to thick edge via programs Aggregates: Extended inlet zone Chain conveyor central lubrication, pneumatic manual Quick-change glue basin device, currently one glue basin available Top pressure manual adjustment, PU rollers Infeed ruler manual adjustment with SIKO counter on chip removal Joint milling with slide ...

Power: N/C (electro-pneumatic system) Operating parameters: Workpiece length 250–2,500 mm; max. width 1,200 mm; automatic longitudinal + transverse feeding; electropneumatically controlled cross scale Workpiece capacity: Panels/components of varying dimensions; suitable for furniture & wood processing lines Supported edges: Wood-based panels, MDF, chipboard, plywood (typ.) Edge types: Feeding, positioning, transfer Included equipment: Fully automatic WZ10 pulling system; air cushion table; cross alignment scale; integrated control system Compliance: Industrial woodworking equipment; CE N/C Power supply: Electric + compressed air (electro-pneumatic) Year/Manufacturer: HOMAG – PROFI TBL 100/35/12 Remarks: Designed for automatic handling and precise positioning of workpieces in longitudinal and transverse direction Automatic feeding table with WZ10 system for ef ...

4226m total NOT USED. FC18 745,00 H3326 203,00 D1884 300,00 H3389 220,00 H1146 818,00 K5574 76,00 LM12 1720,00 LM64 144,00 Auction-ID: A7-49492-15

4767m total NOT USED. D102 385,00 D129 632,00 D164 225,00 A316 290,00 A379 101,00 A391 272,00 A416 300,00 A423/A433 1156,00 A431 95,00 A440 366,00 A806 700,00 H3368 245,00 Auction-ID: A7-49492-12

Type: wood gluing machine Year: bought second-hand in 2001 Visible model: OM 313 Use: regular application of glue to wooden parts/profiles before assembly or veneer Drive: motorized Feed: adjustable Work Table: Metal Controls: Front control panel Power supply: electric, probably three-phase Equipment: foot switch Condition: pre-owned, visible traces of use Auction-ID: A3-46156-35137

4642m total NOT USED. H1113 1297,00 U741 771,00 0564/PE 787,00 535 FS22 728,00 542 FS22 725,00 U532 261,00 H3005 73,0 Auction-ID: A7-49492-14

Edge banding machine Type: AKRON 1330 A Manufacturer: Biesse Year: 2021 23 touch screen, Windows, SINTRA HD electronically controlled axes and automatic machine adjustment RT02 pre-milling unit with diamond cutters ADZ02 anti-adhesive nozzles SP03 gluing unit EVA + PUR hybrid gluing head AIR FORCE P1 – gapless edging of laser edges with hot air IT03 trimming unit with FLEX system RF02 + PRONESTING milling unit R1 / R2 / 25° multi-profile cutters AR02 cornering/rounding unit RB02 radius sander + PRONESTING R1 + R2 edge RC02 surface sander with pneumatic regulation LPT02 polishing/cleaning fluid nozzles SZ02 brushing/polishing unit additional support roller track Feed speed: 12 m/min. A great advantage of the machine is the possibility of using EVA and PUR glue, as well as the AirForce system for jointless edge banding. Machine in very good condition, fully functi ...

Edge banding machine Type: Sprint 1411 K Manufacturer: Holz-Her Year: 2005 Machine in good condition, fully functional Find more here - .ucymachines/ Contact us at - sales@ucymachines

Powertrim 300 H edger Engine Honda GX 120 Working depth 10 positions blade length 25 cm Weight 30 kg Details oil level protection Machine is working, video available Auction-ID: A1-47389-353

2.2 Kw. With thermal protection. Sanding belt 150 x 3200 mm. Support sheet with a point extraction, removable, large sanding roll 200 mm with extractor hood. Small sanding roll 100 mm. The sanding belt is oscillating in height. And the sanding belt is adjustable in height from 10 to 150 mm. The sanding table is made of a plane with three extraction points, all three equipped with a removable extractor hood. Three-way manifold belongs to machine. 3x extra sanding belt included Equipped with shaving hand sander, Type MB2, 380 volts, 1500 watts and a speed of 1410 rpm, Sanding belt 100 x 860 mm. With sanding table that can be swiveled away. Auction-ID: A1-48994-16

2.2 kw, Sanding belt 150 x 3200 mm Support sheet with a point extraction, removable, large sanding roll 200 mm with extractor hood. Small sanding roller 100 mm with small sanding table Sanding belt is decorative in height Adjustable in height from 10 to 150 mm. With thermal protection. Auction-ID: A1-48994-31

Powertrim 300-H Professional Edger – Honda GX120 – 25 cm Specifications: Brand: Powertrim Type: 300-H Engine: Honda GX120 Engine type: 1-cylinder air-cooled 4-stroke petrol engine Displacement: approx. 118 cm³ Engine power: approx. 4 hp Start: manual pull starter Fuel tank: approx. 2.7 litres Blade length: approx. 25 cm Working depth: adjustable in 10 positions Maximum cutting depth: approx. 10 cm Blade drive: mechanical via V-belt Number of wheels: 4 Wheel diameter: approx. 175 mm / 7 inch Own weight: approx. 30 kg Features: Honda GX120 petrol engine Oil Level Protection Vertical rotating cutting disc Manually switchable blade drive on and off V-belt drive with protective cover Working depth adjustment in 10 positions Four-wheel guide Adjustable front wheel construction Steel frame construction Long control boom with control from the handles Pa ...