drilling press used for sale

pressure: 1500 kN chamfer lenght: 3550 mm distance between columns: 3044 mm Control: Cybelec 34 PS-CN column arm: 350 mm max. ram stroke: 220 mm dimensions of the machine ca.: 3200 x 4200 x 2100 m sheet support: hinten / back number of support arms: 2, verschiebbar / adjust. die shift: hydraulical tool clamping: upper tool quick change system: crown: 3 sets of tools included The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 2000 /1000 t distance between columns: 2650 mm stroke: 500 mm column travel -side: 500 x 1000 mm diameter of piston: 710 mm number of pistons: 2 distance between table / ram: 1000 mm operating pressure: 130 / 230 bar dayligth: 800 mm table length: 2500 mm table width: 1600 mm table height: 250 mm draw back pressure: 500 kN number of T-slots: 8 turning speeds: 1500 U/min rapid speed: 120 - 140 mm/min closing speed: max. 120 - 140 mm/sec. hydraulical ram locking: return of plunger by small single cylinders: 100 - 110 mm/sec cutting sound absorber: 300 t die cushion capacity: 200 t die cushion stroke: 250 mm speed of die cushion: 100 mm/sec voltage: 380 V frequency: 50 Hz quantity of oil: 2000 l total power requirement: 93 kW weight of the machine ca.: 90 t dimensions of the machine ca.: 5000 x 2500 x 7200 mm transport measurements: ca. 6500 x 3750 x 2190 mm 1991 assembly of a di ...

Used Flottweg B-800 double-belt press. Technical data: Type: B-800 Hourly throughput [t/h]: 2-6 Belt width [mm]: 800 Drive power [kW]: 1.5 Electrical connection [V/A]: depending on the country of installation Pneumatic connection [bar]: 6 Design and operating principle: 1. The product is continuously fed into the feed box and evenly distributed on the lower belt. The height and width of the cakes can be adjusted to the specific product. 2. In the wedge zone, the upper belt is pressed against the product. A slow increase in pressure creates a stable product cake. 3. In the extrusion area, the cake is dewatered, first using a special profile roller, which ensures rapid liquid drainage to both sides of the cake. 4. The product is then effectively dewatered by pressure rollers with gradually decreasing diameters and increasing pressure. 5. Optional linear pressure rollers  ...

Buhler DMWP flake mill, 1000x600, complete with electric motor

Whisper compressor Planet Air double piston; as good as new condition; double pistons; 8 bar; Boiler 50 liters. Whisper compressor Planet Air double poppet; condition as new; double poppet; 8 bar; tank 50 liters.

- Pressing force: 1500 kN - Pressure: 300 Mpa - Piston stroke: 300 mm - Downward speed: 9.8 mm/s - Working speed: 2.6 mm/s - Return speed: 13 mm/s - Passage: 1550 mm - Table dimensions: 1530 x 500 mm - Table height adjustment: 750 mm / 5 steps - Stop adjustment: 400 mm - Pressure stamp Ø: 2x 150 mm - Guide piston Ø: 70 mm - Motor power: 7.5 kW - Connection voltage: 400 V - Dimensions WxHxD: 2150 x 2050 x 1000 mm + 750 x 1100 x 750 mm - Weight: 1800 kg

Channel baler Presto HPK 50 HS, built in 2014 Manufacturer: Presto Type: HPK 50 HS Year of Make: 2014 Drive: 30 KW Press force: 50 t Hours: 7145 Filling opening: 1600 x 650 mm (LxW) Channel cross-section: 700 x 950 mm Filling volume, max. 1.06 m³ Cycle time: 20 s Binding: 4-fold throughput at 35 kg/cbm: 5.5 t/h 60 kg/cbm: 8.8 t/h 100 kg/cbm: 12.7 t/h Bale weight: up to 500 kg Machine dimensions: 8420 x 1900 x 2400 mm (LxWxH) Machine weight: approx. 10,500 kg Materials: paper, cardboard, foil, PET bottles Note: Knives and counter-blades as well as all sliding plastics have been replaced. The press is in good condition and has been inspected and tested. You can find a video on our website or YouTube channel. The user manual and CE declaration are available. Please note: All technical data refer to the manufacturer's specifications. We assume no liability f ...

- Pressing force: 1000 kN pressure: 289 bar - Piston stroke: 300 mm - Downward speed: 10.5 mm/s - Working speed: 2.7 mm/s - Return speed: 15 mm/s - Passage: 1050 mm - Table dimensions: 1030 x 460 mm - Table height adjustment: 600 mm / 5 steps - Stop adjustment: 400 mm - Pressure stamp Ø: 110 mm - Guide piston Ø: 60 mm - Motor power: 7.5 kW - Connection voltage: 400 V - Dimensions WxHxD: 2000 x 2150 x 900 mm - Weight: 1250 kg

Key data: 56 kN

Machine Type: Toggle Press Manufacturer: Gechter Type: HKPL 56 Condition: used / very good Offer will only be sent if a complete imprint is provided! Price 2.450 Euro incl. 19% VAT Fixed Price Location Warstein , Germany Reference number M-GEC-0126 DESCRIPTION We offer you a used toggle press from the manufacturer Gechter. With fine adjuster Weight approx. 205kg Max. power 56KN at 6.5 bar Availability: immediately Our offer is aimed at tradespeople who are registered within the meaning of the Trade Regulation Act according to §14 GewO. The offer is subject to change, subject to prior sale. Please provide your full contact details to receive a quote with our terms and conditions of payment. Errors in the descriptions and offers are reserved

Skid similar but no Dynajet, Oertzen, Falch, DIBO, ... S500-30E-C - High pressure pump: Speck P52/30-500 30l/min. at 500bar (year of construction 12/16) - Motor: Electric 30kW - 400l water tank - Pressure gauge - Pressure regulator - Safety valve - Powder-coated steel frame - Aluminium covers - Forklift tabs - Dimensions with 400l water tank: approx. 1,250 x 1,510 x 1,260 - Empty weight: approx. 700 kg - Year of construction: 2009, new high-pressure pump12/2016 - Operating hours: approx. 1500 h

automatic baler Manufacturer: PAAL Type: KONTI 700 G/S Year of construction 2010 Technical data: Press force: 1940 kN/ 198 t at 300 bar Specific pressing force: 160 N/cm² Bale size: 1,100 x 1,100 x length in mm Filling opening: 2,000 x 1,020 mm Drive power: 3 x 75 kW Throughput capacity (according to manufacturer's specifications): approx. 650 m³/h Capacity at 35 kg/m³: 22.5 t/h Capacity at 60 kg/m³: 36.5 t/h Capacity at 100 kg/m³: 55.5 t/h Binding: 5-fold vertical Bale weight: approx. 800 - 1,450 kg depending on baled material and bale length Machine weight: up to approx. 47 t Optional: with Bollegraaf steel plate strip according to picture

Skid similar but no Dynajet, Oertzen, Falch, DIBO, ... S500-30E-C - High pressure pump: Falch xs31.1-30-500 30l/min. at 500bar (year of construction 01/08) - Motor: Electric 30kW - 1250l water tank - Pressure gauge - Pressure regulator - Safety valve - Powder-coated steel frame - Aluminium covers - Forklift tabs and crane eyelets - Dimensions with 1250l water tank: approx. 1,100 x 1,760 x 1,770 - Empty weight: approx. 1,500 kg - Year of construction: 2013 - Operating hours: approx. 1500 h

IMAL GLADIATOR 255 CNC hydraulic press brake was built in 2003 in Italy by I.MA.L. GROUP. The machine is designed for precision machining of sheet metal with a maximum length of 4100 mm. The high press force of 255 tonnes, combined with an extremely stable design, guarantees the best bending results, even during the most intensive challenges. All this is complemented by an advanced DELEM numerical control with all the necessary functions. The IMAL GLADIATOR 255/41 CNC press brake weighs 20800 kg. Technical specifications of the IMAL GLADIATOR 255 press brake - CNC controller: DELEM DA 65 - maximum press force: 255 t (2550 kN) - maximum sheet metal length: 4100 mm - approach speed: 140 mm/s - bending speed: 10 mm/s - return speed: 140 mm/s - reach: 510 mm - slider stroke: 320 mm - maximum distance between work table and slider: 535 mm - work table width: 90 mm - distance bet ...

Polystyrene compressor Styropactor MAXI | Shredder press for Polystyrene EPS Compressor, combination of shredder and press for polystyrene EPS MAXI Commodity number: 42055 Throughput: Measured with fish crates of 25 KG/M3 Material space weight EPS: 70-90 kg/h Throughput measured in fish crates with lid (650 grams per piece and about 800x400x220mm): 100-120 Connection: 7.5kW, 3-phase 400V/50Hz 480V/60Hz Insertion opening: 600×1000 mm Length: 3180 mm Height: 1600 mm Width: 870 mm MAXI PLUS Commodity number: 42060 Throughput: Measured with fish crates of 25 KG/M3 Material space weight EPS: 110-130 kg/h Throughput measured in fish crates with lid (650 grams per piece and about 800x400x220mm): 170-200 boxes/h Connection: 11kW, 3-phase 400V/50Hz, 480V/60Hz Insertion opening: 600×1000 mm Length: 3680 mm Height: 1600 mm Width: 870 mm Wet boxes: YES Stainless stee ...

ROMACO KILIAN TABLET PRESS, MODEL S370 PRIME Medium-sized single-layer rotary tablet press. Modular and compact, for flexible tablet production. Made in Germany. Built in 2022. CHARACTERISTICS - Interchangeable die table - Tablet chute on one side - Simple and intuitive HMI control system - Connectable tablet control unit for automatic in-process control - Weight: 1.925 kg PRODUCTION - Output: 156,000 to 330,000 (depending on tablet size and pressing material) - Printing stations: 26 to 44 - Number of dies: 44; 40; 32; 26 - Tool type (EU and TSM): B; D - Die type: BBS; BB; B; D - Max. pre-compression force: 40 kN - Max. main compression force: 80; 100 kN - Max. tablet diameter: 11; 13; 16; 25 mm - Max. die fill: 16; 20 mm ENERGY CONSUMPTION - Drive power: 5.5 kW - Standard voltage, frequency: 400 V, 50/60 Hz - Compressed air: 6 bar

Baler V8 | 8t pressing force. Press for cardboard, foil, paper. V8 MEDIUM-SIZED BALER Our V8 baler is versatile and offers medium-sized companies that need to process a range of materials, including bulky objects and packages of different sizes, with excellent value for money. The V8 produces bales that fit perfectly on a Euro pallet and is suitable for pressing cardboard, plastic, textiles, paper, polystyrene and food waste Recommended for supermarkets, gas stations, department stores, hotels, factories and logistics centers. Bale size: 800 mm H × 950 mm W × 600 mm D Bale weight: 100–180 kg Pressing time: 33 seconds Pressing force: up to 8 tons Dimensions: 2270 mm H × 1100 mm W × 745 mm D Filling opening: 950 mm W × 485 Integrated bale ejection mechanism Weight: 425 kg Power supply: Single-phase motor with 220 V 50 Hz 1.5 kW Noise: 70 decibels E-Power DIN EN  ...

Baler V20X | 20t press for cardboard, foil, paper, waste Baler, packaging press V20X | 006 With a pressing force of up to 25 tons, the V20X can efficiently compact cardboard, plastic, paper, textiles and food waste. Recommended for markets, department stores, hotels and all other users who have to deal with average amounts of waste and have to work at low ceiling heights. Bale size: 800 mm H (variable) × 1100 mm W × 750 mm D Bale weight: 200–300 kg Pressing time: 35 seconds Pressing force: up to 25 tons Dimensions: 1970 mm H × 1695 mm W × 865 mm D Filling opening: 1100 mm W × 625 mm H Integrated bale ejection mechanism Weight: 980 kg Power supply: Three-phase, 380/400 volt 3 kW motor Noise: 74 decibels DIN EN 16500 IP54 protection class E-Power Standards PLC light indicator "Bale full" and "Automatic pressing process"

2 cloth press 1,0 m cloth width capacity: up to max. 4 t with top fruit

Specification: Nominal force: 2500 ton Ram stroke: 190 mm Number of strokes in 1 minute: 20 Shut height: 800 mm Bolster plate-to-ram adjustable stroke: 15 Table size: 1250x1400 mm Weight 124.230T

The machine is in good technical condition, after prior agreement it is possible to test it. - Nominal forming force: 120 t Working length: 3106 mm CNC control Delem (graphic 2D programming) Automatic calculation of bending sequence and collision detection Back gauge X axis with 2× manually adjustable stop fingers CNC electromotive height adjustment of the back gauge (R axis) CNC electrically controlled table deflection Upper tool adapter ROLLERI Equipment and accessories: - Front protective device (tilting door) - Rear protective device (sliding door) - 1× freely movable two-hand / foot control - Operating instructions including CE declaration

Pressure flange for STARTER MAN 40/54 recon MAN part number: 161.01.011

Pressure pipe ground MAN 40/54 recon MAN part number: 434.01.012

Baler, press for cardboard cardboard, foil paper V50 | 706 SPECIFICATIONS Bale size: 1000 mm H (variable) × 1200 mm B × 800 mm D Bale weight: 350–550 kg Pressing time: 45 seconds Pressing force: up to 50 tons Dimensions: 3055 mm H × 1985 mm W × 1130 mm D Filling opening: 1200 mm W × 640 mm H Weight: 1870 kg Power supply: Three-phase, 380/400 volt 7.5 kW motor Noise: 74 decibels DIN EN 16500 IP 54 protection class PLC light indicator "Bale full" and "Automatic pressing process" CE Certification Made in EU OPTIONS Adaptable for vehicle bodies Suitable for use at sea Automatically opening guillotine door E-Power (three-phase motor with 380/440 volts and 4 kW) PET Press Filling at the back of the machine Electronic weighing system Annual maintenance contract Galvanized Description The V50 is perfect for pressing large volumes of waste and then reselling or ...

Bale size: 600 mm H (variable) × 600 mm W × 400 mm D Bale weight: 15–30 kg Pressing time: 35 seconds Pressing force: up to 8 tons Dimensions: 2500 mm H × 765 mm W × 575 mm D Integrated bale ejection mechanism Hinged door Power supply: Single-phase motor with 220 V 50 Hz 1.5 kW Weight: 415 kg Noise: 70 decibels DIN EN 16500 IP54 protection class PLC with automatic cycle CE Certification Made in EU OPTIONS Collecting tray for residual liquid Suitable for use at sea Electronic weighing system Annual maintenance contract Solar powered Galvanized or stainless steel V5HD PRESS FOR CANS & BOTTLES Fast, efficient and easy to use: The V5HD effortlessly presses aluminium cans and PET bottles to make them easier to dispose of. Recommended for restaurants, pubs, bars and special recyclers. Hinged door and 35-second pressing time Integrated bale ejection mechan ...

CP30 PRESS FOR CANS AND OIL FILTERS With its compact design and a pressing force of 8 tons, the CP30 efficiently presses metal cans and large oil filters up to a size of 30 liters. Recommended for car repair shops, paint shops and food manufacturers. Pressing force of 8 tons Low voltage control and emergency stop knob for safe working Easy removal of cans after pressing and drip tray for residual liquid SPECIFICATIONS Dimensions with stand: 2540 mm H × 1105 mm W × 680 mm D Dimensions without stand: 1435 mm H × 615 mm W × 680 mm D Dimensions of the pressing chamber: 475 mm H × 350 mm W × 350 mm D Weight: 245 kg Pressing time: 35 seconds Pressing force: up to 8 tons Power supply: Single-phase motor with 220 V 50 Hz 1.5 kW Noise: 70 decibels IP54 protection class CE Certification Made in EU OPTIONS Savings model Suitable for use at sea Galvanized or stainl ...

New airend BOGE BA 15 as a replacement for Termomeccanoca SCA8D-R (TM SCA 8 D-R) The installation dimensions are the same. BOGE Id.Nr.: 201021166P ( incl. gasket 60 x 60 x 2 and O-Ring-76x3-N-FKM (Viton) 75)

DARLEY EHP-L 110 31/25 CNC hydraulic press brake was built in 2000 in the Netherlands by DARLEY B.V. The machine is in very good technical condition and has been regularly maintained throughout its service life. In December 2023, all cylinder seals and oil with filters were replaced by an authorised service. In February 2024, on the other hand a full service of the WILA top tool clamping system was performed. The DARLEY EHP-L 110 31/25 is used for precision machining of workpieces with a maximum length of 3100 mm. The high press force of 110 tonnes, combined with an extremely stable design, guarantees the best bending results during even the most intensive challenges. The deflection arrow compensation function additionally ensures the desired angle along the entire length of the bent workpiece. The offer also includes an extensive equipment, consisting of, among others, DELEM’s adva ...

Hydraulic frame press Hungerbühler Press-Measurement: 4100 x 3050mm 3 vertical cylinders 3 horizontal cylinders Height adjustment via control box Width adjustment via control box Supports at the bottom for gluing wings at working height. The machine is in good condition, ready for operation. Subject to change, error, prior sale ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Phone 0041 62 966 18 32 Fax: 0041 62 966 21 12

ZTS KOSICE LE 160 C eccentric press was built in 1988 in Czechoslovakia by Závody Tažkého Strojárstva n.p. Košice. The machine is in very good technical condition and has been regularly maintained throughout its service life. All control solenoid valves were replaced in February 2023. ZTS KOSICE LE 160C is an excellent choice for a wide range of workpiece machining, i.e. punching, cutting and stamping. All of these machining processes are performed with a high press force of 160 tonnes, which, combined with a rigid design, enables the production of parts with high repeatability and excellent precision. The ZTS LE 160 C eccentric press weighs 10150 kg. Technical specifications of the ZTS KOSICE LE 160 C press - maximum press force: 160 t (1600 kN) - maximum number of slider strokes: 50/min - number of slider strokes in single mode: 30/min - maximum slider stroke: 120 mm -  ...

Maximum force ton-force 400 Slider stroke length mm 250 Number of courses of a slider per minute 25 Maximum distance between table and slider (in lower position of slider) mm 670 Table overall dimensions: mm - from front to rear 1000 - from left to right 1000 Main electric motor power kW 40 Press overall dimensions mm - length 3410 - width 3140 - height 5930 Press weight kg 30 600

PKZZ 250 Double Column Crank stamping Press Completely overhauled. Electric and Control- Not available. Table 2500 x 1400 mm Ram 2320 x 1250 mm Distance between uprights 2525 mm Window in table width 2300 mm Window in table depth 850 mm Stroke 400 mm Strokes per minute SPM 12 Adjustment of ram 120 mm Shutheight 550 mm Table cushion force 50 to Cushion stroke 160 mm Motor 32 kW Weight ca. 39 tons

Frame press Hess hydraulic Type: HYDRO-LUX Crimping dimension approx. L 3550 m x W 2250 mm Connected load 380 V / 50 Hz 2.6kw Hydraulic Pump Machine dimensions Length 6600 mm x Width 1600 mm x Height 2770 mm 0 - 8 bar pneumatic Optoelectronic measurement query. The window scantlings are placed in the feed channel so that the photoelectric sensor can measure whether the pressure beams and press corners need to be opened or closed. If the light beam of the probe hits the window scantlings, the machine receives the command to drive up in width and height until the working dimension is reached. Workflow: Automatic dimensional adjustment loose insertion Automatic pressing process loose presentation remove Automatic dimensional adjustment Program selection options in the control system: 1. Automatic measurement adjustment via optoelectronic measurement query with a ...

Key data: 200 t, 500 mm, 200 mm

(1982) 200t Lauffer Hydraulic Press High-Speed Hydraulic Press with Advanced Shock Absorption This Lauffer hydraulic press is a high-performance machine designed for speed and precision, capable of 2,000 kN of pressing force. Its high-speed designation is backed by a rapid descent speed of 330 mm/sec and a sophisticated 8-fold flat guidance system to maintain ram alignment even under heavy or off-center loads. Technical Details Machine Type: Hydraulic Press Manufacturer: Lauffer Model: RPS 200 Year of Manufacture: 1982 Nominal Force: 200t Max. Return Force: 225 kN Max. Ram Stroke: 200 mm Shut Height: 500 mm Ram Guidance: 8-fold flat guidance Table & Ram Surface Area (W x D): 800 mm x 630 mm Table Hole Diameter: 204 mm Clearance Between Uprights (Front / Side): 840 mm / 320 mm Operating Speeds: Rapid Descent: 0 – 330 mm/sec (steplessly adjustable) Pre ...

Fortuna dough dividing and working machine Type: A3 Completely overhauled repainted Division of 30 Weight range dough pieces 32-80 grams Dough insert per saucer 960-2400 grams with incubation electric head The robust design and duration oil lubricating of the transmission parts ensures a long service life Easy cleaning of the knife head 380V / 50Hz Weight of the machine approx. 640 kg Machine stands on a specially made wheelchair Dimensions: Height: 150 cm Width: 60 cm Depth: 70 cm The machine was completely dismantled and completely overhauled from the ground up. Then completely repainted.

USED KORSCH MODELO PH 230 ROTARY PRESS REF.: E6431

Block glue press Müro 5000/A2 WT; Working width 705mm; 3x dryer; Stack increase; heat deflector; Stand-standing device. Padding press Müro 5000/A2 WT; working width 705mm; 3x dryer; pile elevation; heating sheet; floor mounted machine.

Bending Lenght 3050 mm Bending force 135 ton Crowning Type Motorised Controller ModEva 19T CNC back gauge X - R Z manuel

Key data: 250 t, 500 mm

(2018) 250t Hidroliksan Hydraulic Press Hydraulic Press with Integrated Die Cushion for Deep Drawing This 2018 hydraulic double-column press is a heavy-duty production unit designed for versatility, featuring a robust 250-ton capacity and high-quality Rexroth and SICK components. With its 100-ton integrated die cushion and generous 500 mm stroke, it is exceptionally well-suited for complex deep drawing and forming operations that require precise pressure control. Technical Details ‍ Machine Type: Hydraulic Double-Column Press Manufacturer: Hidroliksan Model: H-TYPE Nominal Force: 250t Return Force: 50t Stroke Length: 500 mm Speeds: Approach: 160 mm/sec Pressing: 5 – 15 mm/sec Return: 190 mm/sec Working Surfaces: Ram Plate: 1,000 x 800 mm Table Plate: 1,000 x 800 x 100 mm Components: Pump: REXROTH (71cc – 103 L/min) Motor: 22 kW (30 hp), 1,500 rpm ...

Stationary high-pressure pump unit Hammelmann HDP 122 on base frame. Similar but no Kamat, Uraca, Woma. Pump type: HDP 122 Operating pressure: 440 bar Flow rate: 92 l/min. Drive speed: 1500 rpm. Drive power: 75 kW with AC motors ACM 208S 75 kW electric motor, IP55, with pressure control valve, with safety valve, with oil cooling system. Dimensions LxWxH: approx. 1,800x900x1,450 mm Weight: approx. 1,230 kg Year of construction: 2015 Condition: in very good used condition.

Code: 0328 Brand: ITALPRESSE Model: GL / 14,5 - 50 - 420 T - CE Standard Hydraulic press for composite materials and solid surfaces, moulds and decorative panels, suitable for use in the aerospace, aviation, woodworking, furniture, interior design, automotive, shipbuilding, construction, energy, defence, sports and public transport sectors, and various – CE Standard – Year 2005 Technical data: N°5 solid steel plates 1450 x 500 mm N° 3 pistons Diathermic oil heating Total thrust 420 tonnes Working diagram - see enclosed diagram Max power 9,3 Kw Full-load current 19 A The oil tank is located on top of the press and is fitted with a sight glass for checking the oil level Fluid (oil) temperature controller Two-hand control for closing the press Photocell safety barriers Fixed safety guards

The CE08 series is an electrically driven high-pressure cleaner. This model is the ideal tool for general cleaning work. Built into a stainless steel frame, this robust high-pressure cleaner is easy to move and can be equipped with various accessories, such as rotor nozzles, chemical injectors and a sandblasting kit. Similar but no Dynajet, Falch, Kärcher, Oertzen, etc. Available models: ----- CE08-200 50Hz 200 bar 16 l/min. CE08-200 60Hz 200 bar 16 l/min. General Specifications: ----- Power of the drive motor: 6.0 kW Volts: 400V (50Hz) - 440V (60Hz) Amp: 12.8A (50Hz) - 12.3A (60Hz) Dimensions: 690 mm x 560 mm x 900 mm Weight: 70 kg Includes standard accessories.

Maximum pressure: 9 tons Pressing force: 1.94 kg/cm² Bale size: 770x600x500 mm Bale weight: - Power supply: 400 V/4 kW Year of construction: 1997 Productivity: - Price: on request

Compressive force: 170 t Spindle Ø: 160 mm Table support surface: 700 x 900 mm Plunger area: 500 x 800 mm Gr. Distance between table and plunger: 450 mm Drive motor: 380 V, 11 kW Weight: 8200 kg