Technical data:
Maximum parent roll width: 1420 mm
Minimum parent roll width: 600 mm
Maximum parent roll diameter: 1500 mm
Maximum parent roll weight: 2500 kg
Maximum unwinding tension (Ø1500 mm): 600 N
Minimum unwinding tension (Ø1000 mm): 40 N
Minimum standard slitting width: 100 mm
Maximum rewinding width: 1400 mm
Maximum rewinding diameter: 1050 mm
Maximum rewinding weight: • Ø76 mm shaft: 600 kg
• Ø152 mm shaft: 1000 kg
Maximum rewinding tension: 600 N
Maximum production speed: 600 m/min
Power supply: 3 x 400V 50Hz
Installed power: 30 kW
Compressed air: 6 bar, dry
Materials to be slit:
• Paper-based / liner-based packaging laminates.
• Board from 80 to 300 g/m².
Unwind section:
A separate between-centers unwinder, type T9, 1500 mm diameter,
including:
• Hydraulic cylinder control for lifting parent rolls from the
floor.
• Two motors driving the unwinding roll, controlled by an ultrasonic
diameter sensor and a tension-control dancer roller.
• Two pneumatic expanding adapters, SVECOM, for 70/76 mm (3")
cores.
• Two pneumatic expanding adapters, SVECOM, for 150/152 mm (6")
cores (mounted on the pneumatic end adapters).
• Floating edge-correction roller.
• Automatic web guiding system, FIFE DP20, with SE26A photoelectric
sensor, ±100 mm correction via electric actuator — for controlling
sheet edge or continuous printed line.
• Connecting walkway allowing web threading at floor level while
keeping full access to the slitting station.
• All web path rollers are anodized.
• Safety guarding for operator protection.
Slitting section:
A slitting station with individual pneumatic knives and circular
counter-knives:
• Shear cut performed against the counter-knives.
• Counter-knife shaft driven by an independent motor; counter-knife
shaft is pneumatic.
• Pneumatic knife holders mounted on a beam with a dovetail guide
(TIDLAND) and an air supply manifold for individual activation.
• 10 slitting sets, each including: Individual TIDLAND pneumatic
knife holder (25 mm width) and double-bevel circular knife Ø 90/60
mm.
• Set of multi-groove counter-knife rings, 5 mm pitch, 50 mm
length.
Web separation section:
• A separator roller driven by the slitting motor; angle and
curvature fully adjustable.
Lay-on roller:
• Lay-on roller made of anodized ground aluminum or polyurethane
(depending on materials).
• Pressure is adjustable and synchronized with winding diameter.
• Roller is removable.
Automatic splicing / transverse cutting system:
• Hydraulically operated pivoting arm, including a transverse knife
with linear motion and a backing plate for securing the web onto new
cores.
Trim extraction system:
• Trim suction unit with two width-adjustable nozzles.
• Turbine enclosed in a sound-insulated cabinet, conveying trim to a
centralized system or container (not included).
Rewinding section:
• Motorized turret (two-position) supporting two rewinding
shafts.
• Rewinding shaft drive by an oversized asynchronous motor.
• Hydraulic centering point for the active rewinding roll.
• Two pneumatic expanding shafts Ø76 mm (3"), max load 600 kg each,
equipped with full-width rubber strips with individual bladders.
• Two pneumatic expanding shafts Ø152 mm (6"), max load 1000 kg
each, also equipped with full-width rubber strips with individual
bladders.
Electrical & pneumatic system
• Main asynchronous motor
• Electrical cabinet mounted on the machine side, connected by a
3-meter cable, housing motor drives and PLC
• Main control panel including controls for braking, rewinding,
emergency stop, lay-on roller, and auxiliary functions
• 10'' color touchscreen "DIGITAL PILOT", providing:
o Programming and storage of production parameters
o Diagnostics and alarm management
o Display of web tension (unwind & rewind)
o Display of roll diameters (unwind & rewind)
o Length counter with automatic stop at programmed length
o Diameter counters with automatic stop at selected diameter
o Adjustment of tension curves, core diameters, material types
o Storage of up to 500 production recipes
o Display of machine status and faults
o PLC program monitoring for maintenance staff
• Ewon® remote service (requires LAN access via RJ45)
Germany
10707 Berlin 
