cold rolling mill used for sale

Dry ice cleaner with only 108 operating hours and flexible use of all types of dry ice ColdJet SDI 60 Select ice blasting machine from 2013 With blasting hose, blasting gun (applicator in industrial design with lighting), grounding cable, round nozzle 11mm and flat nozzle 45mm with integrated 3-stage scambler Power supply: 230Volt maximum dry ice capacity of the container approx. 27kg Dry ice consumption adjustable from approx. 0 to 160kg per hour Jet pressure range from approx. 1.4 bar to 17 bar Compressed air requirement depends on the nozzle used The gun with integrated light and the ability to switch between only air and air + ice is very practical The device can be used with 3mm dry ice pellets, or alternatively with ice blocks, discs and nuggets, in which case the required ice is scraped off. So you can flexibly use any available dry ice. Instruction manual in English ...

COLD JET DRY ICE BLASTING MACHINE COLD JET MODEL 2000 DRY ICE BLASTER GOOD CONDITION EXWORKS HAMBURG GERMANY VOLTS 230 AMPS 4 PHASE 1 FREQUENCY 50/60 FULL LOAD AMPS 4 MOTOR AMPS 2.5 HP 1 SHORT CIRCUIT INTERUPTING CAPACITY 300A MAX OPERATING PRESSURE 300 PSI / 20.7 BAR SHIPPING WEIGHT 315 LB / 143 KGS

Star Cold Water Chiller 2015, Two fan system, refrigeration R404A, 3Ph

- for Walterwerk Kiel Jupiter baking oven - for different angles and cone lengths

Qty. 1 Second-hand cold rolling mill Mfc.: MCC, ABB, IMS Type: 6-Hi Cold Rolling Mill Built: 2009 Stopped: 2017 Annual capacity: 220,000 Ton/Year Annual running time (Hour): 6480 Strip Width: 800~1250 mm Thickness Entry: 1.5~3.5 mm Exit: 0.2 – 1.2 mm De-Coiler OD: 1000~2000 mm De-Coil ID: 610 mm De-Coil Weight: Max. 25 T Coil OD: 1000~2000 mm Coil ID: 610 mm Coil Weight: Max. 25 T Mill Max Speed: 1300 m/min Threading Speed: 30 m/min Main Drive Controller (3300 VAC) Mfc.: ABB ACS6000 Variable Speed Variable Voltage Xray Gauge Mfc.: IMS Germany Automation Siemens PLC/Wincc

Qty. 1 Second-hand double stand cold rolling mill stand Mfc.: SMS/Germany Type: 4-Hi Double Stand Cold Rolling Mill Built: 2009 Stopped: 2017 Capacity: 800,000 Ton/Year Annual running: 6480 h Strip width: 800 – 1650 mm Thickness entry: 1.8~5.0 mm Exit: 0.3 – 2.5 mm Coil OD: 1000~2200 mm Coil ID: 610 mm Coil Weight: Max. 30 T Line Speed: max. 1350 m/min Threading Speed: 30 m/min

Qty.1 Second-hand Aluminium cold rolling mill Mfc.: SPIDEM Type: 4-Hi Non Reversing Built: 1964 Installed: 2017 (new mechanical & hydraulic, PLC – ABB, AGC) Stopped: 2020 Strip width: 1700 mm Thickness Entry: 11 mm Exit: 0.2 mm Rolling speed: 450 m/sec. with edge trimming: 300 m/sec. Mill force: 1500 T WR Length: 1830 mm Dia.: 465 / 500 mm Back-up rolls Length: 1830 mm Dia.: 1100/1200 mm De-coiler Max. counter traction force: 5500 kgP Reduction ratio: 1:5.53 Revolution: 72.3 – 199 RPM Speed: 136.5 – 375 m/min. Coiler (2 x 400-1100 RPM) Max. traction force: 15000 kgP Reduction ratio: 1:4.41 (470 m/min.) Speed: 9.9 – 200 m/min.

Qty. 1 Second-hand 3 stands 4-Hi Tandem cold rolling mill line Mfc.: Demag Type: 4-Hi Built: 1968 Material to be rolled: low carbon steel Strip width: 600 †1500 mm Thickness Entry: 2.5 mm Exit: 0.2 mm Entry: Coil ID: 510 mm OD: 1800 mm Weight: 15 MT Exit: Coil ID: 510 mm OD: 1800 mm Weight: 15 MT Work roll: dia. 380 mm x 1650 mm Roller bearings Back-up rolls: dia. 1150 mm x 1650 mm Oil film bearings Housing: Closed top, cast steel construction Housing post: 762 x 552 mm Rolling speed: 240 m/min.

Qty. 1 Second-hand cold rolling mill Mfc.: SUNDWIG/MINO Type: 4-HI Built: 1980 Revamped: 2016 Rolled material: Carbon steel SAE1006, S235-S550, C45-C75, IF Strip width max.: 600 mm Thickness: in 6.0 mm out 0.25 – 5.0 mm Speed max.: 500 m/min Coil size: ID 508 mm OD 2000 mm Back-up roll dia.: 590 mm - 625 mm Work roll dia.: 190 mm - 240 mm Motors stands: DC, EAA converters (installed 2004), Rolling force: 500 Tons Coolant Emulsion Filtration by magnetic system Controls PLC system: SIEMENS Scada: Simplicity Thickness control: Entry stand hydraulic equipped with Automatic Gap Control (AGC) Thickness control: Exit stand Utilities: Electrical voltage: 380 V, 3 Phase, 50 Hz Air pressure: 5 Bar Cooling water No. of work rolls: 120 used + 8 brand new No. of back-up rolls: 8 Electric Drawings Mechanical Drawings Certification: Allegato V/8 ...

Qty.1 Second-hand cold rolling mill Mfc.: Achenbach, INNSE/MINO Type: 4-Hi Revamped: 2015 Strip width: 1500 mm Thickness Entry: 6.0 mm Exit: 0.3 mm Run-out table width: 1600 mm Rolling speed: 600 m/min. Motors Mfc.: Simemotori Fire Protection System Lubrication system

Capacity: 0 t Diameter: 105 mm Length: 0 mm Horizontal and vertical:Horizontal  Shaft Ø:               105mm Number of rolls:       3 Stroke X-Axis:         300mm Capacity Tube:         60 x R 1000 Ø x mm Capacity T-Profile:    80 x 80 x 8 x R 1000 mm Capacity HEA-Profile:  140 x R 2500 mm Working speed:         1000 - 24000 mm/min. Length:                1.500 mm  Width:                 1.200 mm  Height:                1.400 mm  Weight:                1.700 kg  set universal rolls set pipe rolls BC 25 control system    ...

Qty. 1 Second-hand 4 stands cold rolling mills – 4-Hi Mfc.: Fröhling Built: 1969 Revamped hydraulics: 1984 Dismantled and in storage 2018 Rolled material: Alloy AA5050, AlMg3 (Series 3000 & 5000) Type: 4-Hi Strip width max.: 282 mm Thickness: in 2.0 mm out 0.25 – 1.20 mm Speed max.: 400 m/min

Mfc.: Hitachi Type: 6-Hi reversing mill Built: 1976 Shut down: 2014 Revamped: 2010 Control system – changed DC to AC motors Load cells were replaced in March 2005 & thickness gauge in March 2009 Roll coolant cooler was replaced in July 2009 Control boards of hydraulic screw down & electromagnetic valves were replaced in 2009. Strip width: 610 – 1330 mm Thickness Entry: 1.6-4.5 mm Exit: 0.15 – 2.3 mm

Capacity: 0 t Diameter: 0 mm Length: 0 mm CN sections bender Manual and Automatic mode for forming discontinuous radius shapes such as Ovals Volutes Ellipses Parabolas     Horizontal and vertical:H + V  Shaft Ø:               100mm Number of rolls:       3 Horizontal:            Yes  Vertical:              Yes  Resistance moment:     33CM³ Capacity flat:         100x 20 mm Capacity Tube:         114,3 x 3,6 Ø x mm Capacity bar:          90 x 5 mm Capacity T-Profile:    100 x 100 mm Capacity HEA-Profile:  120 x 58 mm Working speed:         2,5 - 5 - 7,5 mm/min. Length:  ...

Capacity: 0 t Diameter: 120 mm Length: 0 mm MACH - ID 6233 Make: PULLMAX KUMLA Type: Z-60 CNC Control: PS/R - CNC V5 YOP: 1993 Horizontal and vertical    H + V Shaft Ø    120 mm Number of rolls   3 Resistance moment     56 CM³ Capacity flat    125 x 20 x 1300 mm Capacity Tube     115 x 1200 mm Capacity bar       65 x 65 x 1000 mm Capacity T-Profile     120 x 120 x 13 x 1200 mm Capacity HEA-ProfileUNP     240 x 1800 mm Working speed     6,6 / 6,5 M/Min mm Dimensions Length      1.830 mm Width       1.540 mm Height      1.600 mm Weight      4.600 kg

Capacity: 150 t Diameter: 470 mm Length: 300 mm SPECIFICATIONS Hydraulic / Mechanical HydraulicHorizontal / Vertical / or H + VH + V Shaft Diameter ø170 mm Roll diamter ø470 mm Shaft length300 mm Working speed M/Min.1/8 M/Min Capacity HEB 160 x 160 x 15 x Diam = 1600 mm Capacity Flatt 150 x 25 x Diam = 1500 mm  Power  16 DIMENSIONS Length  3400 mm Width  3390 mm Height  2800 mm Angle 150 x 150 x 16       Ø 1.500Angle 140 x 140 x 15       Ø 1.400T       120 x 120 x 14       Ø 1.200T       160 x 160 x 15       Ø 1.600Flat   150 x 25            &nbs p; Ø 1.500

Capacity: 0 t Diameter: 0 mm Length: 0 mm SPECIFICATIES Werking Hydraulisch / Servo / Mechanisch  Mechanical Horizontaal en of verticaal  Hor. As diameter Ø200 mm  Rol diameter Ø350 mm As lengte in mm    630 mm Werk snelheid in M/Min.   4.5 - 9 M/Min Buig capaciteit  IPN  120 x R 2500 mm Buig capaciteit  HEB220 x 22 x R 3500 mm Buig capaciteit  Buis  1 33 x 6,0 mm Vermogen in Kw   15 kW kW AFMETINGEN Lengte 2100 mm Breedte 2000 mm Hoogte 2100 mm  

Capacity: 0 t Diameter: 400 mm Length: 180 mm

Capacity: 0 t Diameter: 145 mm Length: 0 mm Make Comac Galileo 4 Type Galileo 40 Year 2011 Profile bender comac galileo 40 Outside diameter max. (mm)Section modus 6 cm3 Inside diameter max. (mm)Shaft diam = 45 Max. pipe length (mm)Roll diam = 145 Max. angleSpeed = 3,7 M/min Wall Thickness (mm)Tube 70 x 2 x 2000 Flatt 60 x 10 x 600 mm Bar 35 x 35 x 600 mm Manipulator Hor & Vert  

Capacity: 360 t Diameter: 140 mm Length: 0 mm Make Roundo R 5 S Type R 5 S Year 1989 Section modulus 50 cm3 Outside diameter max. (mm)Top shaft = 140 mm Inside diameter max. (mm)Lower shaft = 120 Max. pipe length (mm)Rolls = 360 Max. angle Power = 11 kW Wall Thickness (mm) Weight 4000 Kg Tube = 142 x 1.800 mm HEA = 140 x 900 mm Some tooling  

Capacity: 0 t Diameter: 42 mm Length: 3000 mm Max.Tube Ø:        42mm Min. Tube Ø:       6mm Max. Wall thickness:2,5 mm Max. Bending radius:270mm Min. Bending radius:25mm Max. bending length:3.000mm 3e dimsion bending:360,000 mm/min. Power:             5.5kW Length:            4.700 mm  Width:             1.300 mm  Height:            1.600 mm  Weight:            3.750 kg 

rolling capacity max.: NA t workpiece diameter: 38 mm workpiece length: 500 mm total power requirement: 24 kW weight of the machine ca.: 10 t dimensions of the machine ca.: m Max.Ø tool slide stroke 760 mm Max.Ø rack length 610 mm Length of workpiece between centres, approx. 500 mm Max. tooth width / profile width 92 mm Max. workpiece Ø 38 mm Tailstock stroke on outboard support, hydraulic, approx. 500 mm Module range 0.3 - 1.3 Total electrical load, approx. 24 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features KBH Workpiece Feed Device, standing parallel to the machine, at present set-up for feed-in and feed-out of shaft-formed workpieces, approx. Ø 16 x 200 mm long, with prism conveyor belt and lifting station for 2 shafts (blank and finished part), as well as workpiece positioning control. Originally, external gears were formed on the machine using  ...

Qty. 1 Second-hand copper rolling mill Material: Copper & Copper Alloy (Pbc, Etc.), Aluminium, Etc. Manufacture: Hitachi(Japan) Type: 4-Hi Reversing Rolling Mill Strip Width: Max 450 mm Thickness: 0.3 mm ~ 4.0 mm (Copper) Line Speed: 100 m/min. Coil Weight: 5,000 kg Manufacturing Date: 1963 1st Revamping Date: 2008 2nd Revamping Date: 2010 3rd Revamping Date: 2020. 05 Revamping: Mill Housing Clean & Painting Improvement of Screw Down System (Ram Cylunder --- Geared Motor) Change of Deflector Roll & Press Plate Right/Left Reel: Increase Capacity Right Reel: 30 kW, 200/500 RPM – 110 kW, 650/1,800 RPM, Left Reel: 30 kW, 200/500 RPM – 75 kW, 400/1,500 RPM Change of Drive for 2-Coil Car: Hydrauric Cylinder – Geared Motor

Description: Machine no. 218 Control: conventional Workpiece diameter 115 mm Workpiece length 2150 mm Toothing diameter 120 mm Number of teeth - max. 96 Number of teeth - min. 12 Rolling head speed 1,800 rpm Feed rate 30 - 180 mm/min Rapid traverse 1,800 mm/min Total power requirement 20 kW Approx. Onsite Dimension. (l x w x h): 5,700 x 3,000 x 2,300 mm, weight approx.: 11,000 kg

rolling capacity max.:2-20 t workpiece diameter:100 mm total power requirement:2 x 8,5 kW weight of the machine ca.:11 t dimensions of the machine ca.:7,1 x 5,15 x 3,9 m Description of the manufacturer: The ROLLEX® is more than an innovation offered by Profiroll in the field of Spline Rolling. This flexible machine type enables a rolling of splines onto most different types of shafts. The CNC-control combined with symmetric circular dies allow a manufacturing of splines with highest quality demands. Likewise the ROLLEX® is able to coldform profiles, threads and to perform finishing rolling due to its reliable Profile Rolling process. Circular Die Process circular dies for kinematic rolling with symmetric geometry this correlates to a rolling rack of infinite length a workpiece specific calibration phase achieving least tolerances is the result lowest changeover times due to com ...

rolling capacity max.:6,1 t workpiece diameter:160 mm workpiece length:25 mm total power requirement:14 kW weight of the machine ca.:4000 kgs dimensions of the machine ca.:2,5 x 2,5 x 2,1 m Internal rolling machine for transmission shift sleeves

workpiece diameter:38 mm workpiece length:500 mm rack milling length - max.:610 mm profile width:92 mm module range:0,3-1,3 slide stroke:760 mm drive motor: kW electrics - voltage/frequency:380/50 V/Hz total power requirement:24 kW weight of the machine ca.:10 t Spline/cold Rolling Machine EX-CELL-O XK 251 with automatic loading device FELSOMAT PE03, fitted in 1999 and tailstock. A cold rolling machine, intended for non-cutting shaping of profiles, such as plug type gearing (straight or diagonal), spiral gearing, oil grooves

workpiece diameter:38 mm workpiece length:500 mm rack milling length - max.:610 mm profile width:92 mm module range:0,3-1,3 slide stroke:760 mm drive motor: kW electrics - voltage/frequency:380/50 V/Hz total power requirement:52 kW weight of the machine ca.:10 t Spline/cold Rolling Machine EX-CELL-O XK 251 with automatic loading device FELSOMAT PE03, fitted in 1999 and tailstock. A cold rolling machine, intended for non-cutting shaping of profiles, such as plug type gearing (straight or diagonal), spiral gearing, oil grooves

Used cold room with storage freezer LILLNORD, type: Combirum C225-600 -In bakery condition- Refrigerator K 225-165 -10°C / +43°C - For 4 to 6 rack trolleys Storage freezer / fermentation interrupter TF 225-435 - 0° / -20°C - for 18 rack trolleys Assembly on request Condition: Very good, ready for immediate use Inspection and test run are possible by arrangement.

STRIP WIDTH: 750 MM, ENTRY THICKNESS: 0.5 MM, EXIT: 2 x 0.007 MM,

1 x NEW 'Bainite' (India) Make 1000mm (42in) wide x 400mm (16in) dia two roll mill, Hydraulic nip adjustment (dual acting cylinders), Peripherally drilled chilled cast iron rolls (Hardness 65/72 Shore), with anti friction roller bearings, Friction ratio 1:1.08, Hinged guide plates, Lubrication system comprising pneumatic intensifier with grease reservoir, Electro pneumatic brake with power fail safe mechanism. Safety bars fitted to front and rear. Compact right angle drive with 45kW Siemens AC variable speed squirrel cage motor through heavy duty helical design direct drive reduction gearbox (SF 2), Back roll speed 18rpm/front roll 16.6rpm. All mounted on a compact design fabricated steel bedplate. Stainless steel tray underneath. Including electrical controls comprising Siemens G130 VFD drive and S7-1200 plc with HMI. CE marked, with full Technical file, Documentation and S ...

REVAMPED: 1990, WIDTH: 700-1400 MM, THICKNESS: 100 MICRONS - EXIT: 2 x 5 MICRONS 1500 M/MIN.,

Reed 42" x 16" Two Roll Mill. 40HP Motor, with clutch brake. Friction ratio 1.1 Manual Nips. On one-piece steel bedplate.

Qty. 1 Second-hand foil rolling mill plant Mfc.: World Co. (Japan) Type: 6-Hi – Non reversing mill Built: 2002 Application: Copper foil Width: 400 – 700 mm Coil weight: Max. 5 Ton Thickness Entry: 100 – 200 microns Exit: 5 – 100 microns Speed: 0-400/800 m/min. Thickness X-Ray unit AGC system Variable Crown Control Hydraulic servo equipment Main motor power: 200 kW DC Slitter line Mfc.: IHI Width: 150-700 mm Thickness 5 – 50 microns Degreasing line Mfc.: World Co. Strip width: 700 mm Thickness: 10-50 µm Treatment line Mfc.: Kawasaki Built: 2005 Width: 700 mm Thickness: 10-50 µm

Qty 1 x Shaw 60in x 22in two roll mill, Manual nip adjustment, Peripherally drilled rolls (front and back), Hinged guide plates, Sleeve bearings with motorised lubrication, Right angle drive gearbox with 115Kw DC variable speed motor, All mounted on a heavy duty bedplate. Carter stockblender mounted on too. Complete with controls etc and in very good condition.

1 x Heavy duty 2 roll mill Roll dimensions: 2100mm x 665mm dia. Hydraulic nip adjustment, Safety push bars, Peripherally drilled rolls, Sleeve bearings with grease lubrication, Right angle drive gearbox, with Siemens 240kW DC variable speed motor, Strip knives fitted to front roll, Heavy duty fabricated bedplate, Carter stockblender mounted on top.

Qty 1 x Schwabenthan 200mm dia x 450mm wide two roll mill, Manual nip adjustment, Digital nip gap readout, Electrically heated rolls, Jahnel gearbox with 10HP motor to each roll (variable speed), Variable friction ratio/roll speeds, Stainless steel interlocked guards and tray. Complete with electrical controls and in good condition. O/a dimensions 2700 x 1500mm

Qty 1 x Schwabenthan 150mm dia x 350mm wide two roll mill, Manual nip adjustment, Digital nip gap readout, Electrically heated rolls, Even/friction selectable gear ratios, Motor mounted under frame. Complete with electrical controls and in good condition. O/a dimensions 2400 x 850mm.

Reed 40” x 16” Two Roll Mill Hand operated nips Right angle drive Tray fitted beneath Mill Rolls

Berstorff Cracker Mill with Roll dia 600 x 800mm Description attached!

Berstorff Cracker Mill, Excellent condition, Length of roller 600mm, Roller diameter 430mm, Rubber mill weight 10 tons, Width 2150 mm x 4200 mm long x approx 1800 mm high, The Following work has been completed: New plain bearings, New Roller ribbing, New Roller ground, New Grease pump, brake cylinder, New Safety bars, New Conveyor,

Key data: 190 mm, 450 mm

available Lab Mill! Description attached !

Qty. 1 Second-hand complete 12-Hi reversing cold rolling mill incl. sand blast line Mfc.: Kobelco Type: 12-Hi reversing Built: 1986 Strip width: 900 – 1250 mm Thickness: Entry: 3.2 mm Exit: 0.4 mm Rolling speed: 120/300 m/min.

Rolling milling machine Koepfer 153 A/CNC Manufacturer Jos. Koepfer & Söhne GmbH Type 153 A/CNC Built in 1988 Machine No. 153199 Technical data Largest Module 2 Distance workpiece tool axis max. 4- 87 mm max. workpiece diameter - without magazine 142 mm - with magazine 80 (100) mm max. milling length 150 mm max. length workpiece - without magazine 300 mm - with magazine 220 mm min. number of teeth 3 min. screw gait number 1 Main spindle through- 33 mm Hole Mounting hole for 50 mm Jig max. cutter diameter 70 mm max. cutter width - Universal milling head 63 mm - Shifting milling head 71 mm max. axial cutter shift - Universal milling head 40 mm - Shifting milling head 44 mm 35 Longitudinal feeds 0.1 -5.0 mm /WU 10 cutter speeds 210-1680 /min Control (2 axes) CNC Drive power 2.2 kW Weight approx. 2400 kg Available immediately Location  ...

manual roll gap adjustment 2x7.5 kW motor Bearing Oil circulation lubrication adjustable roller speed 10-41 rpm BJ 1990

REHEAT FURNACE Type: Walking Beam Incoming Billet: 160 x 160 mm x 8.300 – 12.000 mm Charge: Hot and Cold Discharging Temperature: 1150 Degr. Nominal Production 90 Ton/Hr Fuel: Natural Gas (LNG) Furnace inside dimensions: L x W 12.500 x 12.800 mm REBAR ROLLING MILL: Type: Housingless Stands Roughing Mill: 6 Stands Intermediate Mill: 6 Stands Finishing Mill: 6 Stands Horiz. Stands # 1,3,5,7,9,11,13,15,17 Vert. Stands # 2,4,6,8,10,12,14 Horiz./Vert Stands #16 and 18 CROP SHEAR No. 1 Head & Tail Cropping, Emergency Chopping Type: Crank Shear- Blade width 200 mm CROP SHEAR No. 2 Head & Tail Cropping, Emergency Chopping No. of Blades: 4- Blade width 180 mm DIVIDING SHEAR Cutting to multiple lengths COLD SHEAR Cutting to final length Shear type; CMC 0630 0950 No. of Blades: 2- Blade width 900 mm Product Length: 6-12 Meter (Standard)  ...

Qty. 1 Second-hand aluminium foil rolling mill plant Mfc.: Robertson, Kampf, Schmutz, Nishimura, Waldrich-Siegen, Otto-Junker Built: 1962 – 1989 Foil width: 850 mm Entry thickness: 0.4 mm Exit: 2 x 7 microns Scope of supply: Roughing Foil rolling mill: 4-Hi Intermediate foil mill 4-Hi Finishing foil mill 4-Hi Slitters – Qty. 4 Roll grinders – Qty. 2 Annealing furnaces – Qty. 4 Charging car INDIVIDUAL ITEMS CAN BE SOLD

Robust fine rolling mill with 800 mm roll width and 800 mm roll diameter, incl. main drives, auxiliary drives, control cabinet and hydraulic unit for splitting. In regularly maintained condition, rollers without riefen. Available for an extra charge: Matching dust filter from Hellmich.

Fine rolling mill with 800 mm roll width and 800 mm roll diameter, incl. main drives and auxiliary drives, split adjustment manually. In regularly maintained condition, rollers without riefen. Available for an extra charge: Matching dust filter from Hellmich.