cold roll used for sale

Dry ice cleaner with only 108 operating hours and flexible use of all types of dry ice ColdJet SDI 60 Select ice blasting machine from 2013 With blasting hose, blasting gun (applicator in industrial design with lighting), grounding cable, round nozzle 11mm and flat nozzle 45mm with integrated 3-stage scambler Power supply: 230Volt maximum dry ice capacity of the container approx. 27kg Dry ice consumption adjustable from approx. 0 to 160kg per hour Jet pressure range from approx. 1.4 bar to 17 bar Compressed air requirement depends on the nozzle used The gun with integrated light and the ability to switch between only air and air + ice is very practical The device can be used with 3mm dry ice pellets, or alternatively with ice blocks, discs and nuggets, in which case the required ice is scraped off. So you can flexibly use any available dry ice. Instruction manual in English ...

COLD JET DRY ICE BLASTING MACHINE COLD JET MODEL 2000 DRY ICE BLASTER GOOD CONDITION EXWORKS HAMBURG GERMANY VOLTS 230 AMPS 4 PHASE 1 FREQUENCY 50/60 FULL LOAD AMPS 4 MOTOR AMPS 2.5 HP 1 SHORT CIRCUIT INTERUPTING CAPACITY 300A MAX OPERATING PRESSURE 300 PSI / 20.7 BAR SHIPPING WEIGHT 315 LB / 143 KGS

Star Cold Water Chiller 2015, Two fan system, refrigeration R404A, 3Ph

Used cold room with storage freezer LILLNORD, type: Combirum C225-600 -In bakery condition- Refrigerator K 225-165 -10°C / +43°C - For 4 to 6 rack trolleys Storage freezer / fermentation interrupter TF 225-435 - 0° / -20°C - for 18 rack trolleys Assembly on request Condition: Very good, ready for immediate use Inspection and test run are possible by arrangement.

rolling capacity max.:2-20 t workpiece diameter:100 mm total power requirement:2 x 8,5 kW weight of the machine ca.:11 t dimensions of the machine ca.:7,1 x 5,15 x 3,9 m Description of the manufacturer: The ROLLEX® is more than an innovation offered by Profiroll in the field of Spline Rolling. This flexible machine type enables a rolling of splines onto most different types of shafts. The CNC-control combined with symmetric circular dies allow a manufacturing of splines with highest quality demands. Likewise the ROLLEX® is able to coldform profiles, threads and to perform finishing rolling due to its reliable Profile Rolling process. Circular Die Process circular dies for kinematic rolling with symmetric geometry this correlates to a rolling rack of infinite length a workpiece specific calibration phase achieving least tolerances is the result lowest changeover times due to com ...

Qty. 1 Second-hand 3 stands 4-Hi Tandem cold rolling mill line Mfc.: Demag Type: 4-Hi Built: 1968 Material to be rolled: low carbon steel Strip width: 600 †1500 mm Thickness Entry: 2.5 mm Exit: 0.2 mm Entry: Coil ID: 510 mm OD: 1800 mm Weight: 15 MT Exit: Coil ID: 510 mm OD: 1800 mm Weight: 15 MT Work roll: dia. 380 mm x 1650 mm Roller bearings Back-up rolls: dia. 1150 mm x 1650 mm Oil film bearings Housing: Closed top, cast steel construction Housing post: 762 x 552 mm Rolling speed: 240 m/min.

Qty. 1 Second-hand cold rolling mill Mfc.: SUNDWIG/MINO Type: 4-HI Built: 1980 Revamped: 2016 Rolled material: Carbon steel SAE1006, S235-S550, C45-C75, IF Strip width max.: 600 mm Thickness: in 6.0 mm out 0.25 – 5.0 mm Speed max.: 500 m/min Coil size: ID 508 mm OD 2000 mm Back-up roll dia.: 590 mm - 625 mm Work roll dia.: 190 mm - 240 mm Motors stands: DC, EAA converters (installed 2004), Rolling force: 500 Tons Coolant Emulsion Filtration by magnetic system Controls PLC system: SIEMENS Scada: Simplicity Thickness control: Entry stand hydraulic equipped with Automatic Gap Control (AGC) Thickness control: Exit stand Utilities: Electrical voltage: 380 V, 3 Phase, 50 Hz Air pressure: 5 Bar Cooling water No. of work rolls: 120 used + 8 brand new No. of back-up rolls: 8 Electric Drawings Mechanical Drawings Certification: Allegato V/8 ...

Capacity: 0 t Diameter: 105 mm Length: 0 mm Horizontal and vertical:Horizontal  Shaft Ø:               105mm Number of rolls:       3 Stroke X-Axis:         300mm Capacity Tube:         60 x R 1000 Ø x mm Capacity T-Profile:    80 x 80 x 8 x R 1000 mm Capacity HEA-Profile:  140 x R 2500 mm Working speed:         1000 - 24000 mm/min. Length:                1.500 mm  Width:                 1.200 mm  Height:                1.400 mm  Weight:                1.700 kg  set universal rolls set pipe rolls BC 25 control system    ...

Qty. 1 Second-hand double stand cold rolling mill stand Mfc.: SMS/Germany Type: 4-Hi Double Stand Cold Rolling Mill Built: 2009 Stopped: 2017 Capacity: 800,000 Ton/Year Annual running: 6480 h Strip width: 800 – 1650 mm Thickness entry: 1.8~5.0 mm Exit: 0.3 – 2.5 mm Coil OD: 1000~2200 mm Coil ID: 610 mm Coil Weight: Max. 30 T Line Speed: max. 1350 m/min Threading Speed: 30 m/min

Qty. 1 Second-hand cold rolling mill Mfc.: MCC, ABB, IMS Type: 6-Hi Cold Rolling Mill Built: 2009 Stopped: 2017 Annual capacity: 220,000 Ton/Year Annual running time (Hour): 6480 Strip Width: 800~1250 mm Thickness Entry: 1.5~3.5 mm Exit: 0.2 – 1.2 mm De-Coiler OD: 1000~2000 mm De-Coil ID: 610 mm De-Coil Weight: Max. 25 T Coil OD: 1000~2000 mm Coil ID: 610 mm Coil Weight: Max. 25 T Mill Max Speed: 1300 m/min Threading Speed: 30 m/min Main Drive Controller (3300 VAC) Mfc.: ABB ACS6000 Variable Speed Variable Voltage Xray Gauge Mfc.: IMS Germany Automation Siemens PLC/Wincc

Qty. 1 Second-hand 4 stands cold rolling mills – 4-Hi Mfc.: Fröhling Built: 1969 Revamped hydraulics: 1984 Dismantled and in storage 2018 Rolled material: Alloy AA5050, AlMg3 (Series 3000 & 5000) Type: 4-Hi Strip width max.: 282 mm Thickness: in 2.0 mm out 0.25 – 1.20 mm Speed max.: 400 m/min

Mfc.: Hitachi Type: 6-Hi reversing mill Built: 1976 Shut down: 2014 Revamped: 2010 Control system – changed DC to AC motors Load cells were replaced in March 2005 & thickness gauge in March 2009 Roll coolant cooler was replaced in July 2009 Control boards of hydraulic screw down & electromagnetic valves were replaced in 2009. Strip width: 610 – 1330 mm Thickness Entry: 1.6-4.5 mm Exit: 0.15 – 2.3 mm

rolling capacity max.: NA t workpiece diameter: 38 mm workpiece length: 500 mm total power requirement: 24 kW weight of the machine ca.: 10 t dimensions of the machine ca.: m Max.Ø tool slide stroke 760 mm Max.Ø rack length 610 mm Length of workpiece between centres, approx. 500 mm Max. tooth width / profile width 92 mm Max. workpiece Ø 38 mm Tailstock stroke on outboard support, hydraulic, approx. 500 mm Module range 0.3 - 1.3 Total electrical load, approx. 24 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features KBH Workpiece Feed Device, standing parallel to the machine, at present set-up for feed-in and feed-out of shaft-formed workpieces, approx. Ø 16 x 200 mm long, with prism conveyor belt and lifting station for 2 shafts (blank and finished part), as well as workpiece positioning control. Originally, external gears were formed on the machine using  ...

Capacity: 0 t Diameter: 0 mm Length: 0 mm CN sections bender Manual and Automatic mode for forming discontinuous radius shapes such as Ovals Volutes Ellipses Parabolas     Horizontal and vertical:H + V  Shaft Ø:               100mm Number of rolls:       3 Horizontal:            Yes  Vertical:              Yes  Resistance moment:     33CM³ Capacity flat:         100x 20 mm Capacity Tube:         114,3 x 3,6 Ø x mm Capacity bar:          90 x 5 mm Capacity T-Profile:    100 x 100 mm Capacity HEA-Profile:  120 x 58 mm Working speed:         2,5 - 5 - 7,5 mm/min. Length:  ...

Capacity: 0 t Diameter: 120 mm Length: 0 mm MACH - ID 6233 Make: PULLMAX KUMLA Type: Z-60 CNC Control: PS/R - CNC V5 YOP: 1993 Horizontal and vertical    H + V Shaft Ø    120 mm Number of rolls   3 Resistance moment     56 CM³ Capacity flat    125 x 20 x 1300 mm Capacity Tube     115 x 1200 mm Capacity bar       65 x 65 x 1000 mm Capacity T-Profile     120 x 120 x 13 x 1200 mm Capacity HEA-ProfileUNP     240 x 1800 mm Working speed     6,6 / 6,5 M/Min mm Dimensions Length      1.830 mm Width       1.540 mm Height      1.600 mm Weight      4.600 kg

Capacity: 150 t Diameter: 470 mm Length: 300 mm SPECIFICATIONS Hydraulic / Mechanical HydraulicHorizontal / Vertical / or H + VH + V Shaft Diameter ø170 mm Roll diamter ø470 mm Shaft length300 mm Working speed M/Min.1/8 M/Min Capacity HEB 160 x 160 x 15 x Diam = 1600 mm Capacity Flatt 150 x 25 x Diam = 1500 mm  Power  16 DIMENSIONS Length  3400 mm Width  3390 mm Height  2800 mm Angle 150 x 150 x 16       Ø 1.500Angle 140 x 140 x 15       Ø 1.400T       120 x 120 x 14       Ø 1.200T       160 x 160 x 15       Ø 1.600Flat   150 x 25            &nbs p; Ø 1.500

Capacity: 0 t Diameter: 0 mm Length: 0 mm SPECIFICATIES Werking Hydraulisch / Servo / Mechanisch  Mechanical Horizontaal en of verticaal  Hor. As diameter Ø200 mm  Rol diameter Ø350 mm As lengte in mm    630 mm Werk snelheid in M/Min.   4.5 - 9 M/Min Buig capaciteit  IPN  120 x R 2500 mm Buig capaciteit  HEB220 x 22 x R 3500 mm Buig capaciteit  Buis  1 33 x 6,0 mm Vermogen in Kw   15 kW kW AFMETINGEN Lengte 2100 mm Breedte 2000 mm Hoogte 2100 mm  

Capacity: 0 t Diameter: 400 mm Length: 180 mm

Capacity: 0 t Diameter: 145 mm Length: 0 mm Make Comac Galileo 4 Type Galileo 40 Year 2011 Profile bender comac galileo 40 Outside diameter max. (mm)Section modus 6 cm3 Inside diameter max. (mm)Shaft diam = 45 Max. pipe length (mm)Roll diam = 145 Max. angleSpeed = 3,7 M/min Wall Thickness (mm)Tube 70 x 2 x 2000 Flatt 60 x 10 x 600 mm Bar 35 x 35 x 600 mm Manipulator Hor & Vert  

Capacity: 360 t Diameter: 140 mm Length: 0 mm Make Roundo R 5 S Type R 5 S Year 1989 Section modulus 50 cm3 Outside diameter max. (mm)Top shaft = 140 mm Inside diameter max. (mm)Lower shaft = 120 Max. pipe length (mm)Rolls = 360 Max. angle Power = 11 kW Wall Thickness (mm) Weight 4000 Kg Tube = 142 x 1.800 mm HEA = 140 x 900 mm Some tooling  

Capacity: 0 t Diameter: 42 mm Length: 3000 mm Max.Tube Ø:        42mm Min. Tube Ø:       6mm Max. Wall thickness:2,5 mm Max. Bending radius:270mm Min. Bending radius:25mm Max. bending length:3.000mm 3e dimsion bending:360,000 mm/min. Power:             5.5kW Length:            4.700 mm  Width:             1.300 mm  Height:            1.600 mm  Weight:            3.750 kg 

Qty. 1 Second-hand copper rolling mill Material: Copper & Copper Alloy (Pbc, Etc.), Aluminium, Etc. Manufacture: Hitachi(Japan) Type: 4-Hi Reversing Rolling Mill Strip Width: Max 450 mm Thickness: 0.3 mm ~ 4.0 mm (Copper) Line Speed: 100 m/min. Coil Weight: 5,000 kg Manufacturing Date: 1963 1st Revamping Date: 2008 2nd Revamping Date: 2010 3rd Revamping Date: 2020. 05 Revamping: Mill Housing Clean & Painting Improvement of Screw Down System (Ram Cylunder --- Geared Motor) Change of Deflector Roll & Press Plate Right/Left Reel: Increase Capacity Right Reel: 30 kW, 200/500 RPM – 110 kW, 650/1,800 RPM, Left Reel: 30 kW, 200/500 RPM – 75 kW, 400/1,500 RPM Change of Drive for 2-Coil Car: Hydrauric Cylinder – Geared Motor

Qty.1 Second-hand cold rolling mill Mfc.: Achenbach, INNSE/MINO Type: 4-Hi Revamped: 2015 Strip width: 1500 mm Thickness Entry: 6.0 mm Exit: 0.3 mm Run-out table width: 1600 mm Rolling speed: 600 m/min. Motors Mfc.: Simemotori Fire Protection System Lubrication system

Qty.1 Second-hand Aluminium cold rolling mill Mfc.: SPIDEM Type: 4-Hi Non Reversing Built: 1964 Installed: 2017 (new mechanical & hydraulic, PLC – ABB, AGC) Stopped: 2020 Strip width: 1700 mm Thickness Entry: 11 mm Exit: 0.2 mm Rolling speed: 450 m/sec. with edge trimming: 300 m/sec. Mill force: 1500 T WR Length: 1830 mm Dia.: 465 / 500 mm Back-up rolls Length: 1830 mm Dia.: 1100/1200 mm De-coiler Max. counter traction force: 5500 kgP Reduction ratio: 1:5.53 Revolution: 72.3 – 199 RPM Speed: 136.5 – 375 m/min. Coiler (2 x 400-1100 RPM) Max. traction force: 15000 kgP Reduction ratio: 1:4.41 (470 m/min.) Speed: 9.9 – 200 m/min.

Rollen-Laminiergeraet - Roll Laminator GBC Aquila 65 Year 2019 - Serial-No. PCG0226 Formatbreite / Size width max. 650mm Heiss-/Kaltlaminierung / Hot and Cold lamination Specifications Operation Mode Roll film laminator Heating System 2 heated rollers Laminating Speed (variable) max. 3000mm/min Max. Pouch Thickness max. 2 x 250 micron rolls Photo friendly Warm up Time 10min Power Supply 220/240 V/AC Laminating Thickness max. 6.0mm Laminating Width max. 330mm Anti-Jam Technology Manual Reverse Approx. lamination time (A4) 6 secs (A4 75 microns) Dimensions (WxHxD) 685 x 330 x 457mm Weight 37.8kgs Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nuernberg - Can be test

Rollen-Laminiergeraet - Roll Laminator GBC Ultima 65 Year 2018 - Serial-No. PGG0734 Formatbreite / Size width max. 650mm Heiss-/Kaltlaminierung / Hot and Cold lamination Specifications Operation Mode Roll film laminator Heating System 2 heated rollers Laminating Speed (variable) max. 3000mm/min Max. Pouch Thickness max. 2 x 250 micron rolls Photo friendly Warm up Time 10min Power Supply 220/240 V/AC Laminating Thickness max. 6.0mm Laminating Width max. 685mm Anti-Jam Technology Manual Reverse Approx. lamination time (A4) 6 secs (A4 75 microns) Dimensions (WxHxD) 889 x 355 x 533mm Weight 62.4 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nuernberg - Can be test

Description: Machine no. 218 Control: conventional Workpiece diameter 115 mm Workpiece length 2150 mm Toothing diameter 120 mm Number of teeth - max. 96 Number of teeth - min. 12 Rolling head speed 1,800 rpm Feed rate 30 - 180 mm/min Rapid traverse 1,800 mm/min Total power requirement 20 kW Approx. Onsite Dimension. (l x w x h): 5,700 x 3,000 x 2,300 mm, weight approx.: 11,000 kg

rolling capacity max.:6,1 t workpiece diameter:160 mm workpiece length:25 mm total power requirement:14 kW weight of the machine ca.:4000 kgs dimensions of the machine ca.:2,5 x 2,5 x 2,1 m Internal rolling machine for transmission shift sleeves

workpiece diameter:38 mm workpiece length:500 mm rack milling length - max.:610 mm profile width:92 mm module range:0,3-1,3 slide stroke:760 mm drive motor: kW electrics - voltage/frequency:380/50 V/Hz total power requirement:24 kW weight of the machine ca.:10 t Spline/cold Rolling Machine EX-CELL-O XK 251 with automatic loading device FELSOMAT PE03, fitted in 1999 and tailstock. A cold rolling machine, intended for non-cutting shaping of profiles, such as plug type gearing (straight or diagonal), spiral gearing, oil grooves

workpiece diameter:38 mm workpiece length:500 mm rack milling length - max.:610 mm profile width:92 mm module range:0,3-1,3 slide stroke:760 mm drive motor: kW electrics - voltage/frequency:380/50 V/Hz total power requirement:52 kW weight of the machine ca.:10 t Spline/cold Rolling Machine EX-CELL-O XK 251 with automatic loading device FELSOMAT PE03, fitted in 1999 and tailstock. A cold rolling machine, intended for non-cutting shaping of profiles, such as plug type gearing (straight or diagonal), spiral gearing, oil grooves

We offer the labeler after comprehensive overhaul and modernization (including cabinet). The machine is designed for bonding three paper labels on glass bottle. Implementation of fully stainless steel. Labeller is equipped with two stations: - adhesive label front, neck and back label. Scanning system and label transfer is based on the pallets, which select a label from a magazine, transfer it onto the gripper drum and then onto bottle. The machine is extremely stable and reliable. Support comes down to refill glue and charge labels into magazine. Capacity: max. 24 000 b/h. We provide 1 set of equipment designed for a customer bottle. Machine has full 12-month warranty.

Cold water set make Combitherm Germany, water-cooled, cca.400Kw.with 2 pcs. Screw compressor Bitzer Type CSH 7571-90Y, refrigerant R 407C, two circles 50/50%, with control Digital uwm. Y.O.M.2005.Little used.state like new. Model KWW 7500 R407C

Cold water set water-cooled, turbo-cooling machine, Carrier 19XR5556, R134a, 400V 50Hz,Bj 2001,ca 2500KW (700ton)Cooling capacity, little operating hours, always maintained,very good condition, super efficiency.

Cat. No. 11-3160 New Standard: Material V2A (AISI 304) Operating pressure max 0.49 bar Container completely stained, passivated and neutralized Heating jacket height 970 mm Insulation made of PU foam thickness = 80 mm Standard: Manhole top Ventilation valve made of PVC Manhole inside oval 440 x 350 and manhole outside rectangular for insulated container Test tap Stand display 24 mm Ladder bracket Residual drain with outlet pipe DN 50 Digital thermometers Clear drain DN 50 Transport eyelets Cat. No. Contents Diameter Height Cyl.Height Feet 11-3160-1 1200l 1350 mm 2070 mm 1000 mm 3 11-3160-2 2400l 1350 mm 3130 mm 2160 mm 3 Disc valve DN 50 Price on request For inquiries: Tel: 09353 90905-0 or Fax: 09353 90905-22 Mobile: 0171 651 82 48 On request, we will be happy to send you our complete catalogue. All prices are ex works plus law VAT Interm ...

2 pcs available can also be used for other rooms of the food industry Dimensions: Also single for sale per piece 500,00 Euro

OVERHAULED IN 1997, SAW BLADE DIA.: 1000 MM, DRIVE PIN HOLES: 4 x 30/200 MM; ROUND MATERIAL DIA.: 360 MM, SQUARE: 330 MM; FLAT PROFILES: 600 x 260 MM, 6 STEPS OF SPEEDS,

Francis Shaw 90mm coldfeed rubber extruder.Year: 1992. Machine No.4846Vented. Side power roller feed,L/D ratio 20:1,H series David Brown gearbox,Thrige Scott 63kW, 2000rpm DC variable speed motor.Machine fully overhauled, cleaned/painted and fitted with NEW electrical control panel. With provision for 5 x TCU's.

Automatic slicer Bizerba A 404, with base frame. The machine is immediately available and can be tested in Koblenz, Germany.

Automatic slicer Bizerba A 404 with base frame. The machine is immediately available and can be tested in Koblenz, Germany.

Make: Omes Type: Tramatic 370S Year of construction: 1988 Saw blade diameter: 350 mm Features of this machine are: -mechanical pneumatic Vice -hydropneumatic feed can be adjusted (see Control Panel) -Saw process and open the Vice manually or automatically -After reaching the depth of saw the saw head will return automatically to its basic position Saw capacity - 90 ° degree cut -Diameter of 130 mm -100 x 100 mm rectangular tube -Fermentation cuts adjustable - right-hand and left-hand fermentation, if necessary in a voltage Machine has been little used

Qty. 1 Second-hand rail hard metal saw with drilling unit Mfc.: Heller Type: TEK001-73-37 Saw carriage: 610 ? 710 mm Cutting speed ? 6 stages: 63-200 m/min. Cutting area: rail height up to: 200 mm rail width up to: 200 mm Feeding speed: 50 ? 1250 mm/min. Power: 50 kW Drilling unit Qty. 3 Drilling spindles Drill diameter: 12 ? 40 mm z-stroke: 630 mm z-drill stroke (adj.): 250 mm Tool changing stroke (adj.): 380 mm Drill spindle diameter: 60 mm Min. distance from the end of the rail: 33 mm Drill spindle distance - spindle 1-3: min. 228 mm max. 600 mm Drill spindle distance ? spindle 1-2: min. 114 mm max. 486 mm Drill feeding speed: 40 ? 200 mm/min. Motor power: 30 kW, 1420 RPM Revolution range: Qty. 9 225 ? 280 ? 350 ? 450 ? 560 ? 710 ? 900 ? 1120 ? 1400 RPM

Thank you for your interest in our used machines we can offer you as follows: Many thanks for your interest in our second-hand machinery, please find below our offer: Manufacturer / manufacturer: National Lab model / type: 1000-1 Proficool UKT recirculating cooler/chiller chiller temperature controller Details / different: laboratory chillers ProfiCool UKT 1000 1 / almost good as new! Extremely quiet laboratory chillers with maintenance-free, air-cooled chiller. Heat exchanger made of brass. Control Panel with electronic controls with digital display (LED) as well as separate a / output switches for pump and cooling. External casing made of stainless steel. Filler for filling of the cooling circuit. Hose connections (olives) with a 12 mm outer diameter.

Make: CLIMAVENETA Type: WRAT/SL 0802 Power: 200 kW (100KW) Refrigerant: R407C Built: 2006 2 pcs. compressors Make: DWM Copeland Semi-Hermetic Type: D6SJ1-400X-AWM/D One circle is defective, others are OK. Price on request

- (H) Mr President, I would like to OCEAN TECH - only the hydraulic module OCTACC 400-600 M.T.A. S.p.A. the hydraulic module OCTACC 400-600 is an external hydraulic kit with frame and housing and suitable for external control (release) and external processing of fault messages. It includes pump and storage tank. In addition to the pump and tank, all hydraulic kits have the following components: • Membrane expansion vessel • Vent valve • Safety valve • Emptying tap • Filling kit with manometer Hydraulic kit as external component for HOCT 400 / 500 / 600 Pump type P1 Number of pumps 1 Rated power per pump kW 4.0 Available print ext. Bar 1.0 - 2.0 Flow rate m3/h 5.9 - 56 Execution external Tank capacity l 350 Length hydraulic kit mm 1950 Wide hydraulic kit mm 785 Height hydraulic kit mm 1200 Serial number: 2200325782 Built in 2018 Condition: Optical ...

TRENNJAEGER Cold circuit saege - see pictures

TUGRA ALU - COLD SAWS TYPE DK 400 -Zaagblad 400 mm -Verstek Dubbel -4 pneumatic clamps -Material Panel met lengteaanslag -Blaaspistool -Beschermkap -Documentatie -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)

Refrigerant filling and service system Manufacturer: Agramkow Type: RHS 1280 year of construction: 2010

SMEVA 48 M2 Product number:M18-7071 Cooling capacity:0,001 kW Dimensions:8000 x 6000 x 2480 mm Number in stock:1 piece(s) Price:Quotation request Very nice Smeva cold room of 48 m2, two entrance doors, 5 drawer kabinets and 10 glass doors (5 frames). Visit also our website: used-refrigeration