129,243 used machines on RESALE, but how to find them? Machine Search
New galvanized or painted construction supports 3m, 3.50m, 4.00m at great conditions directly from the factory. From.21,50€/ Piece+ VAT Construction support painted 1,60m – 2,90m = 21,50€/piece reinforced version 2,00m - 3,50m = 23,50€/ piece reinforced version 2,30m – 4,00m = 26,50€/ piece reinforced version Construction support galvanized 1,60m - 2,90m = 25,90€/ piece reinforced version 2,00m - 3,50m = 26,90€/ piece reinforced version 2,10m – 4,00m = 29,90€/ piece reinforced version 1 frame for construction supports new, painted 70,00€ New inclined supports, painted 1,70m - 3,00m = 29,50€/ piece Inclined supports new, painted 2.10m - 3.50m. = 35,50€/ Piece Inclined supports new, painted 2,40m - 4,10m. = 38,50€/ Piece New inclined supports, galvanized 1,70m - 3,00m = 38,90€/ piece New inclined supports, galvaniz ...
WASHING INSTALLATION 90° One washer to washing system to clean the containers. The containers are tilted 90 degrees and transported through a washing device. The washing device consists of a housing that contains a spray device which is suitable for cold water with a pressure of 5bar. A conveyor belt to transport the containers. After washing, the containers are tilted back to horizontal position. No recycling water included. The concrete floor must be prepared to drain the water to a certain drain pit. The best option is lower the concrete floor in the area of the washer. OVERHEAD DE/STACKER For the PLC controlled movement, stacking and destacking of empty, containers with a maximum weight of 100 kg an overhead stacker/destacker is installed. The stacker/destacker can PLC controlled take up from: -a- The destacking position on the buffer (this is also the ...
Cobot collaborative robot Dobot CR10 new - with Safeskin Reach: 1300mm Payload: 10kg Collaborative robot series Supports payloads of 3 kg, 5 kg, 10 kg and 16 kg Safe working on the side and cost-effectively Hand guidance, collision detection and trajectory reproduction Ideal for application scenarios with human-robot collaboration Multiple control methods Low latency and high noise immunity Supports controls on Android, iOS and Windows High-performance network card with a transfer rate of up to 433 Mbit/s Intelligent interactive panel robot hand guidance The Intelligent Interactive Panel is embedded with LEDs that indicate the status of the robot With the touch of a button, you can drag and move the robot to teach it a specific path Wide compatibility Wide compatibility with a wide range of peripherals Suitable for feeding, assembling, testing, handling, screwing, gr ...
To check torque on air and electric screwdrivers.
COMPAIR L11-7.5A screw compressor was built in 2014 in Italy. The compact oil-injected screw compressor with a capacity of 1820 l/min at an operating pressure of 7.5 bar delivers high-quality compressed air at low operating costs. All key operating parameters are continuously monitored by the state-of-the-art DELCOS PRO control, guaranteeing continuous and reliable operation throughout its service life. The screw compressor is additionally equipped with, among others, a refrigeration dryer, an oil separator and a 500 litre KOMNINO KPL-500/L-13 tank. The total weight of the machine is 219 kg. Technical specifications of the COMPAIR L11-7.5A compressor - capacity at maximum working pressure: 1820 l/min (1.82 m3/min) - maximum working pressure: 7.5 bar - suction pressure: 1 bar - motor speed: 3000 rpm - operating hours: 26399 h - operating hours under load: 4346 h - tank capacity: ...
Dobot collaborative robot Cobot CR 16 - new Range: 1000mm Payload: 16kg Collaborative robot series Supports payloads of 3 kg, 5 kg, 10 kg and 16 kg Safe working on the side and cost-effective Hand guidance, collision detection and trajectory reproduction Ideal for application scenarios with human-robot collaboration Multiple control methods Low latency and high noise immunity Supports controls on Android, iOS, and Windows High-performance network card with a transfer rate of up to 433 Mbit/s Intelligent Interactive Panel Robot Hand Guide The Intelligent Interactive Panel is embedded with LEDs that indicate the status of the robot With the touch of a button, you can drag and move the robot to teach it a specific path Wide Compatibility Wide compatibility with a wide range of peripherals Suitable for feeding, assembling, testing, handling, screwing, grinding and gluing ...
Dobot collaborative robot Cobot CR12 - new Reach 1200mm Payload 12kg Axes 6 Collaborative robot series CR12 Cobot Improves Product Quality: The DOBOT CR12 series is equipped with interactive programming, convenient and easy to master. Quick to execute Improve the flexibility and production efficiency of your product line by setting up an easy-to-implement collaborative CR robot in 20 minutes and getting it up and running in 1 hour. Easy to make Our software and calculation technology make the operation and management of the CR collaborative robot series smart and easy. It can accurately mimic human actions by demonstrating the path. No coding skills are required. Compatible The CR collaboration robot series is recommended not only because of its comprehensive portfolio of end-of-arm tools, but also because of its universal communication interfaces. With multiple I/O ...
Dobot collaborative robot Cobot CR10 - new Range: 1300mm Payload: 10kg Collaborative robot series Supports payloads of 3 kg, 5 kg, 10 kg and 16 kg Safe working on the side and cost-effective Hand guidance, collision detection and trajectory reproduction Ideal for application scenarios with human-robot collaboration Multiple control methods Low latency and high noise immunity Supports controls on Android, iOS, and Windows High-performance network card with a transfer rate of up to 433 Mbit/s Intelligent Interactive Panel Robot Hand Guide The Intelligent Interactive Panel is embedded with LEDs that indicate the status of the robot With the touch of a button, you can drag and move the robot to teach it a specific path Wide Compatibility Wide compatibility with a wide range of peripherals Suitable for feeding, assembling, testing, handling, screwing, grinding and gluing ...
Giusti, cooking vessel, steam jacketed vessel, 225L, central bottom discharge, stainless lid
Screw air compressor Atlas Copco GA 408 59.586 hours of operation Masch. No. ARP 230-128 Built in 1994 Weight 1.2 to L x W x h: 250 x 130 x 200 cm Fqe3oovyi 8 bar 30 kW 2925 / min 380 V 50 Hz This machine is been serviced annually by Atlas Copco. The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12
Te Koop: Endress & Hauser conducta Alarmdekoder. Type MKD
Te Coop: Endress & Hauser Walter Contacters HTA 423
Te Coop: Endress & Hauser Walter Contacters HTA 380
- Single head machine - Direction : R – L - Different bottle sizes - In very good condition
PROFESSIONAL COFFEE FILTER MACHINE COFFEE QUEEN TOWER. Filter coffee machine with vacuum thermoses Coffee Queen Tower is a fast, flexible bulk coffee brewer with a hot water outlet for tea. It features digital display, full and half-brewing function as well as a signal to indicate when the coffee is ready. Brewing can take place on both sides simultaneously and the digital display shows the current temperature, brewing in progress and volume on each side. Characteristics: • Fast and easy to handle bulk brewer with hot water tap. • 2 uniquely designed 5 litre serving stations (vacuum thermoses) with tap, sight gauge and integrated handle grip. • Rotating function for easy handling. • Brewing on both sides at the same time. • Option for full- or half brew and brewing-complete signal. • Full brewing, 10 litres takes approx. 7 minutes. • Thermos with temperature drop o ...
Complete with; push button magnetic starter and safety guards 220 Voltage
ZUCKERMAN CHALLENGER- auto copy lathe and sander, capacity - ( mills 10" dia.by a max. of 120" long) mills using cup cutters- followed by (1) sanding station, unit has hopper feeder, mills & sands one part at a time, does parts like: boat oars, shovel handles, gunstocks, chair legs, ect. Price-$10,900
Reichenbacker copy lathe mills/ turns (6) concentric or non concentric pieces at a time (1) station for your model/sample (models may be wood or metal) complete set up for duck decoys various sizes - items like Queen Ann legs, ect (photos available) (6) milling /working stations
Onsrud twin table copy shaper ONSRUD-auto dual table rotary shaper, model RS-28, for continuous production, 2-speed cutter (5,000/10,000 rpm.) pivots alternately to the right or left table, as center clamp engages, the table rotates, the cutter pivots into your part and continues around template machining the part, the operator unloads and loads new part on alternate table, when cut is complete, operator presses the foot pedal, the cutter then pivots to alternate table &cuts, cycle continues.. $9,900 Contact Fred (716) 433 4224 (12:00 noon is best time to call)
Nitrogen cooling bath, Cryotherm, used Special price If you have a VAT number, we will gladly issue you an invoice without VAT. Used! The system was removed from a machine that had been in operation for a maximum of 2 years. Ensuring the function In order to ensure the functionality of the goods, the buyer must check the goods at the time of acceptance or put them into operation. In case of any defect, which is not the fault of the seller, the goods can be returned within 2 weeks. We will refund the buyer only the product price paid to us. For these goods we have to exclude warranty claims of the buyer for improvement, exchange, subsequent delivery or also for updating in case of digital components. Also excluded is the liability for direct and indirect consequential damages. Our terms and conditions apply, see our website. Austrian law applies without exception and court ...
continuous grilling line grilling surface (w x l) : 600 x 7.500 mm bottom contact grilling + hot air (with flip-over) grilling time : 1 minute to 60 minutes belt width ± 600 mm electrically heated power : 2x200 A, 2x140kW, 3 x 400V, 50 Hz belt washing system adjustable speed overall dimensions (l x w x h) : ± 10.315 x 1.230 x 2.338 mm weight : ± 4.500kg
Laboratory roller for coating laboratory sheets (sample sheets) and plastics
2930-12-334-9601 / 0010985920 2930-12-F23-2495 / 8690980160
We offer Kaeser compressed air system consisting of 2x adsorption dryer DC 75E, compressed air tank 3000 l, piping with ultrafilter, compressed air management system Sigma, oil-water separation system & control cabinet The compressed air system was used to supply compressed air to a production hall. It was built or extended from 1995-2016 and is fully functional, in good condition and is offered for sale by our customer due to the restructuring of the use of the hall. The screw adapter is sold. 1. Screw compressor Kaeser CS 121 75 kW 2, 2x Adsorption Dryer Kaeser DC 75 E Bj. 2016 6-16 bar 3. Compressed air tank flamco STAG 3000 l 16 bar Bj 1995 704 kg 4.Piping with ultrafilter SG 0192, 5,Control system: SIGMA Air Manager Basic 6.Oil-water separation system Kaeser 7.Control cabinet standard Rittal PS 4884 Technical data on the components To 1 photo 1-2 Screw compr ...
The Bio Mark 7 is the largest commercial cold press juicer we manufacture. It features a quick release hopper using two toggle latches, meaning the hopper chute can be removed in seconds and requires no gasket like other manufacturers. It has a Slim top body that still raises up to allow faster bag cleaning and a press only option. It also is our only juicer with a speed control option on the grinder allowing you to control the speed of the grinder. The Mark 7 is for serious cold press juice production and can easily upscale your juice production with simple controls and exceptional performance. apacity: 12 Kg per batch Output: 70 - 100 Litres per hour ( depending on recipe ) Power: Single Phase 240 Vac 50/60 Hz 3.75Kw 22.9 Amp IP66 Max Press Pressure: 3000 PSI Operating Press Pressure: 2200 PSI Motor Power: 5HP Hydraulic Rams: Two Weight: 400 Kg Dimensions: L: ...
used
horizontal conveyor belt with hydromotor
Complete Conversion Kit of TBA-19 330 ml prisam filling machine. All parts in original condition 10/10 and 100 % Tetra pak parts.
approx. 50 pcs in stock Office container - aisle container 16 Fufl / 20 Fufl / 24 Fufl 4.88x2.45x2.6m 6x2.45x2.6m 7.33x2.45x2.6m incl. electricity and lighting For conversion, expansion and/or refurbishment more information: We can configure the containers according to your wishes and conversions! Delivery possible!
2x CHILLER with 660kW; each with 2x BITZER screw compressors; very few operating hours; in 2 containers with 2x recooler on the containers Technical data: Manufacturer: GWK Germany Type: SKW 2 -600 X 2x Bitzer Type: CSW 8593-125Y-40P Containers are heated Operating hours: approx. 5000h Year: 2010/2011, water tank approx. 8 m³ for cold water with 5 pumps 2 x GEA plate heat exchangers for freecooling 2 x 40ft Container High Cube B 3 m connected to each other 2 x GÜNTHNER Glycol Table Cooler W 2.4 m; 500 l capacity; on the container with 12 EC fans each (speed controlled) Refrigerant R134a; 34 kg per circle; Filled complete documentation very good condition more data: see pictures More pictures on request Price on request under infofrigocom.at
High-performance double-sided contact cooking. The Formcook Contact Cooker is excellent for cooking boneless products such as chicken fillets, meat patties, steak, bacon, pancakes, fish fillets, shrimp and vegetables. This cooker has been used to fry vegan products like buns and steaks. The machine was last used in February 2025. Fat-free contact cooking with non-stick belts seals the natural juices and fats in the product for the highest eating quality and minimum cooking losses. The cooking time is adjustable. The Formcook Contact Cooker is manufactured by JBT Corporation in Sweden. More information is available at JBT’s homepage. A conveyor machine manufactured by Ilpra is included. The contact cooker and the conveyor are complete and ready for use.
Cooling compressor, Cooling compressors, Double compressor, Tandem compressors Manufacturer: DWM Copeland Type: DR6J1-4000-EWM Built: 1989 Condition: Used Weight: approx. 450 kg For more data, see also the photos All information without guarantee
COLOMBO AGOSTINO 225.400 coil stamping and punching line was built in 2006 in Italy by Colombo Agostino S.p.A. Its extensive machining capabilities and high reliability make it an excellent choice for series production of components, such as washing machine parts or automotive parts. The production process is fully automatic, thanks to a high-speed feeding system. It unwinds the sheet metal from the coil towards the work station, which features precision tools operating at a maximum force of 400 tonnes. The monolithic design of the machine further ensures high durability and stress-free operation. The COLOMBO AGOSTINO coil-fed punching machine weighs 75000 kg. The coil punching line is complete and consists of the following machines: – 400 t eccentric press: COLOMBO AGOSTINO – sheet metal decoiler: DEF CT 3/128 – coil lift table – sheet metal straightener RA 3000/4-8/120 A ...
Height-adjustable container feet for ISO containers manufactured to ISO 1496-1.
Pressure air compressor, make CompAir / Geveke, type: VMHD 500, for 735 rpm, 21.5 bar, built 1985.
Pressure air compressor, make CompAir / Geveke, type: VMD 750, for 735 rpm, 8.5 bar, built 1991.
RITTAL SK 3365.662 Wall-Mounted Cooling Unit – Blue e Series High-performance wall-mounted enclosure cooling unit designed to provide reliable temperature control for electrical cabinets and control panels in industrial environments. The RITTAL SK 3365.662 from the Blue e Series offers efficient cooling performance and energy-optimized operation for temperature-sensitive electronics. General Information - Manufacturer: RITTAL - Model: SK 3365.662 - Series: Blue e - Machine Type: Wall-mounted cooling unit Technical Specifications - Cooling Capacity: 1,500 W - Voltage Supply: 230 V AC / 50–60 Hz - Protection Class: IP54 (internal and external circuits) - Refrigerant: R134a Dimensions and Weight - Dimensions (W × H × D): 435 × 1,090 × 260 mm - Weight: approx. 45 kg - Condensate Management - System: Electrical condensate evaporation Key Features - Energy-e ...
Capacity: 600 l Heating: steam, 127 kW, 8 bar Outside dimensions 110 x 130 x 135 cm (HxWxD) Inside dimensions 60 x 109 x 88 cm (HxWxD) Control: MC K Mouting Voltage: 230/400 V , 50 Hz Cover: insulated,with springs and hinges of stainless steel, opening 90° Drainage: piston – type drain cock Equipment: valves for cold and hot water
approx. 23 pieces OTTO dangerous goods container, 600L, large container "IBC" – used -: Price per piece from location: 395.- € (net)! Manufacturer: Otto Containersysteme GmbH Type: 11A/X/01/99/D/OTTO/BAM 0356/2556/1090 Manufacturer Part Number: 33782 Year of Make: 1999 Capacity: 600L Tank material: St. W 24 Maximum permissible gross weight: 1.090kg Net weight: 190kg with approval as a large container "IBC" for the national (GGVS/GGVE/GGVS and international (ADR/RID/IMDG code) transport of dangerous goods of packaging groups I, II + III (X-coding) Dimensions according to DIN 30741 Tank made of steel, hot-dip galvanized with hinged, lockable lid Lid locks in place by special spring technology up to approx. 70° at any opening angle Container all around with only 2 closures on the front with forklift pockets, safety hook for PE bags, nameplate and bag Conditio ...
TO WHOM IT MAY CONCERN; WE VE USED ATLAS COPCO SCREW AIR COMPRESSOR. GA 55 AT STOCK PLS FIND SPESIFICATIONS ON BELOW MAWP. 9,1 bar. - 131psi VOLTAGE 440V 60Hz P motor 55kW 75hp YOB 2010 IF YOU VE ANY QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US PS: WE VE ALSO USED AIR COMPRESSOR ATLAS COPCO MAS GA 37 AT OUR STOCK. Aliaga Marine Services info/aliagamarine.com Phn/Fax:+90 232 618 03 85 Mobile: +905556084850 aliagamarine.com TURKEY
TO WHOM IT MAY CONCERN; WE VE USED ATLAS COPCO SCREW AIR COMPRESSOR. MAS GA 37. AT STOCK PLS FIND SPESIFICATIONS ON BELOW MAWP. 9.1 bar. - 131psi VOLTAGE 440V 60Hz P motor 37kW 50hp 2010 YOB MADE IN. BELGIUM IF YOU VE ANY QUESTIONS PLS DO NOT HESITATE TO CONTACT WITH US PS: WE VE ALSO USED AIR COMPRESSOR ATLAS COPCO GA 55 AT OUR STOCK. Aliaga Marine Services info/aliagamarine.com Phn/Fax:+90 232 618 03 85 Mobile: +905556084850 aliagamarine.com TURKEY
MTA Spotcooler SC7.3 Manufacturer: THERMOBILE INDUSTRIES BV Type: Coolmobile 25 (industrial version) Mobile spot cooler Coolmobile 25 for selective cooling of e.g. material, cooling tunnels, room areas and heat sources. The Spotcooler is mobile via wheels and can be easily driven to the place to be cooled. The control panel has an adjustment range of +1°C to +31°C and can be switched on and off automatically via a timer. The device can be used anywhere via a Schuko plug (230V / 50Hz). Cold air can be distributed via three flexible hose nozzles. Warm air can be discharged via a flange and warm air hose (both not included). Specifications: Cooling capacity / kw 7.32 (25,000 Btu) Air flow m/h 10.5 - 8.5 Power connection / V / Hz 230 / 50 Starting current / A 57 Operating current / A 13 Power consumption / Kw 2.6 Air filter aluminum and carbon Max. static pressure / mm 3 ...
MTA Spotcooler SC7.3 Manufacturer: THERMOBILE INDUSTRIES BV Type: Coolmobile 25 (industrial version) Mobile spot cooler Coolmobile 25 for selective cooling of e.g. material, cooling tunnels, room areas and heat sources. The Spotcooler is mobile via wheels and can be easily driven to the place to be cooled. The control panel has an adjustment range of +1°C to +31°C and can be switched on and off automatically via a timer. The device can be used anywhere via a Schuko plug (230V / 50Hz). Cold air can be distributed via three flexible hose nozzles. Warm air can be discharged via a flange and warm air hose (both not included). Specifications: Cooling capacity / kw 7.32 (25,000 Btu) Air flow m/h 10.5 - 8.5 Power connection / V / Hz 230 / 50 Starting current / A 57 Operating current / A 13 Power consumption / Kw 2.6 Air filter aluminum and carbon Max. static pressure / mm 3 ...
Reconditioned powder scatter coating and laminating line for thermoplastic powders. Working width 2 x 000 mm. New powder-spreading system for coating and lamination by means of thermoplastic powders. Working width 2 x 000 mm.
Key data: 75 , 10
Oil-free screw compressor PUREAIR Compair D75HRS 10A 75kw 10 bar 11.4m3/min with frequency converter CompAir D75HRS-10 oil-free, water-injected, Dryclon series frequency converter screw compressor With its 75 kW engine power, it reaches a capacity of 10,320 l/min. The 10 atmosphere operating pressure ensures stable and clean compression, making it ideal for use in areas where air cleanliness plays a key role. COMPAIR D75HRS screw compressor fully serviced, for sale in excellent condition oil-free design, direct drive, controlled by frequency converter. Regulated speed - air and water cooled 75 kW power, air flow: 11.4 m3/min /684 m3/h Built-in frequency converter: Manufacturer: Compair D75HRS 10A Year of manufacture: 2017.12 hours: 36000 Drive power: 75 kW Pressure 10 bar Flow rate: 11.4/min Delco XL controller Main rotor speed: 2980 Voltage: 400 V 50 Hz 3 p ...
Machine a blocs mobile Contec SP 5 pour la fabrication des blocs, hourdis, blocs U, pavee, bordures, blocs mur etc. Max hauteur de produit 300 mm Min hauteur de produit 100 mm surface travaillant max. 1000 x 500 mm Capacité: jusqu´a 3.500 blocs 400 x 200 x 200 mm / 8-heures poste de production
Contec Mini 15 - Concrete mixing plant Mixer M 500/300 liter Capacity 4 - 9 m3 Aggregate hoppers: 2 x 2.5 m3 on a stable metal frame Belts: 2 belts integrated and attached to the aggregate hoppers
NNP Stainless conveyor Stainless frame, overall belt dimensions 1600mm x 900mm, made up of 18mini belts 50mm width, 0.37Kw motors, 3Ph
Convotherm Combi oven Model: OES 6.10 Stainless oven, digital control system, internal dimensions 600mm x 450mm x 500mm, 3Ph
maximum number of results exceeded
please refine your search
