billet shear used for sale

CNC-controlled hydr. Sheet metal shearing machine make WEINBRENNER type TSV 6/3050Machine -No: 687 T built in 1987gr. Working width: 3050 mmFor sheets with 45 kg strength up to: 6.0 mmclear column width: 3160 mmclear stator projection: 200 mmCutting angle min./max .: 1/2 °Backgauge adjustment: 1000 mmNumber of hydr. Hold down: 12Number of strokes min./max. (depending on cutting length and material thickness): 22/36 / minHydraulic drive: 380 V, 15 kWTable height above hall: 900 mmDimensions incl. Backgauge, without frontSupport arms: 4100 x 2300 x 2100 mmWeight approx .: 8500 kgWith- Control in swivel control panel CYBELEC CNC 1000- compl. elec. Device with control device in the large switchingxa0Cabinet attached to the side of the machine- Backgauge control with programming- Material quality code- Sheet thickness preselection- stroke length adjustment- Contact cutting device- Scrapweed- ...

Hydr. CNC-Sheet metal Shear make GWF MENGELE type S 8 - 1500Machine -No: S2544, built in 1989Max. Cutting length: 1550 mmMax. Sheet thickness: 8 mmlateral. Discharge i. Stand: 50 mmSheet metal passage: 16 mmCutting angle adjustable: 2 ° 30 - 0,5 °Empty strokes: 25 - 32Number of hold-downs: 8Cutting pressure: 280 barHold-down pressure: 80 barOil filling: 300 lDrive power: 18.5 kWTotal connected load: 20.1 kWExternal dimensions: 2130 x 3260 x 2360 mmWeight: 5.8 tWith- CNC control SIEMENS S 5 for numerical sheet bending- Holding device mot- Sheet metal removal with conveyor belt- Cutting gap and cutting angle m. Control programmable- Spare knife- Schermesser for 750 kg strength- Separate hold-down z. Cutting after crack- Hold-down pressure adjustable and readable from the front- 2 rocker stops- Finger guard with recessed grip- balls in the support table- Angle stop m. Norius- Footswitchus ...

Crushers

pressure: 60 t square edge steel: 35,0 mm round bar steel: 40,0 mm L-beam: 120 mm punching cross-cut in cmm: 28 in 15 mm throat: 220 mm flat steel: 300 x 15 mm oil volume: 45 ltr. total power requirement: 4,0 kW weight of the machine ca.: 1.250 kg. Dimensions (HxWxD): 1510 x 590 x 1570 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

CNC hydraulic guillotine shears FAbr. HACO HSLX 4010brand newTechnical specifications:Max. Cutting length: 4050 mmMax. Sheet thickness for ST 4 10 mmMax. Sheet thickness VA (1.4301): 6 mmTable height: 1030 mmCutting angle: 0.5 - 3 degreesCutting gap adjustment: 0.05 - 1.0 mmNumber of hold-down devices: 23Back stop area: 1000 mmBackgauge speed: 110 mm / secStroke rate: 7-11Working height: 1030 mmrequired oil filling: 220 litersLength of the angle stop: 1000 mmHolding device option: 7780, -Length of the support surface: 930 mmMax. Sheet thickness: 8 mmMotor power: 18.7 kWOption control panel on the swivel arm: 930.00Machine dimensions: 5150 x 2050 x 2395 mmWeight: 13 tWith- SC 100T controlwith ergonomic control panel - simple operation directly on the cutting table- enables convenient operation ofBackgauge, retraction and cutting length limitation- Electronic cutting gap adjustment - Cutti ...

CNC sheet metal shears make EHT type TSS 4-20Fabr. -No: 107785, year of construction 1998Technical specifications:Working length: 2020 mmmax sheet thickness at 450 N / mm 4 mmOil volume: 160 lelectr. Connection: 400 V, 50 HzDrive line: 7.5 kWDimensions approx: 2800 x 2150 x 2150 mm, weight approx: 4.5 tWith- CNC control ELGO P 8721- Hold-up device- Scrap chute- foot switch- automatic cutting angle- automatic cutting gap adjustment- 3 angle stops in front- Cutting line lightingin a little used and functional conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

digital readout for backgauge retractable backgauge Optional: upgrade to CNC control Cuttinglength: 3100 mm Max sheetthickness st 45: 20 mm Max sheetthickness inox: 15 mm Passage between uprights: 3400 mm Depht of throat: 300 mm Strokes/min: 7 > 30 str/min Backgauge: 1000 mm Adjustable cuttingedge: 0,5 > 3° Electric motor (power): 30 kW Length: 3400 mm Depht: 3900 mm Height: 2800 mm Weight: 22,3 ton

Hydraulic CNC swing cut guillotine shears make KNUTH type KHT D 3006Year of construction 2018Technical specifications:Max. cutting length: 3100 mmMax. sheet thickness: 0.5 - 6.0 mmCutting angle: 1.3°Number of hold-down devices:16Stroke :105mmNumber of strokes per minute:15Working table height: 865 mmNumber of support arms:3Oil tank: 200LMotor power: 15 kWDimensions approx.: 4110 x 2200 x 2100 mmWeight approx.: 7300 kgwith- Sheet metal holding device- D-Touch 7 control with touch screen for motorized backgauge 1000 mm and intersection- foot switchlittle used, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

sheet width: 2100 mm plate thickness: 6,0 mm ST 42 thickness at Niro-steel: 4,0 mm VA cutting angle: 1,2 Grad no. of strokes: 28 Hub/min oil volume: 150 ltr. down holder: 11 Stück control: CYBELEC CybTouch engine output: 11,0 kW back stop - adjustable: 1.000 mm table height: 800 mm weight: 4.500 kg range L-W-H: 3.010 x 2.100 x 1.640 mm ------------------------------------------------- electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment ------------------------------------------------- Furnishing: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws ...

sheet width: 3100 mm plate thickness: 6,0 mm thickness at Niro-steel: 4,0 mm down holder: 14 Stück no. of strokes: 20 Hub/min oil volume: 150 ltr. cutting angle: 1,2 ° control: CYBELEC CybTouch weight: 5500 kg range L-W-H: 4.000 x 2.100 x 1.640 mm total power requirement: 11,0 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hydr. Sheet Metal Shear Make MENGELE Type S 4 - 5000/3Machine -No: S 2237 5000/3 Year 1976Cutting length: 5050 mmMax. Sheet thickness: 3.0 mmlateral. Discharge: 300 mmCutting angle: 0.6 °Strokes per minute: 34Number of hold-downs: 22mot. backgauge: 0 - 1000 mmlateral. Angle stop: 2000 mmOperating pressure: 230 barHold-down pressure: 58 barOil filling: 200 lDrive power: 11 kWOutside dimensions approx: 5750 x 2500 x 1700 mmWeight approx: 15 tWith- mot. backgauge- Angle stop front- Footswitchused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

sheet width: 3100 mm plate thickness: 6,0 mm distance between columns: 3.100 mm down holder: 14 Stück no. of strokes: 16 - 24 Hub/min oil volume: 150 ltr. cutting angle: 0,5 - 1,5 ° thickness at Niro-steel: 4,0 mm column arm: 350 mm engine output: 11,0 kW weight of the machine ca.: 7.060 kg range L-W-H: 4100 x 2200 x 2190 mm -------------------------------------------------- electr. / hydraulic CNC guillotine shears - guided by a backdrop with CYBELEC CNC touch screen control with electr. / hydr. Cutting gap and cutting angle adjustment -------------------------------------------------- Furnishing: - CNC guiding guillotine shears - with electr. / hydr. Cutting gap and cutting angle adjustment - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including s ...

sheet width: 2600 mm plate thickness: 8,0 mm thickness at Niro-steel: 5,0 mm down holder: 12 Stück no. of strokes: 18 Hub/min oil volume: 200 ltr. cutting angle: 1,5 ° engine output: 15,0 kW weight of the machine ca.: 6.300 kg range L-W-H: 3525 x 2350 x 1700 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mm plate thickness: 6,0 mm distance between columns: 3100 mm down holder: 14 Stück no. of strokes: 18 Hub/min oil volume: 150 ltr. cutting angle: 1,2 ° thickness at Niro-steel: 4,0 mm control: CYBELEC CybTouch weight: 6,3 To. range L-W-H: 4.000 x 2.100 x 1.640 mm -------------------------------------------------- electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment -------------------------------------------------- Furnishing: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be folded up at max.travel, for ...

Hydr. Sheat metal Shear make EHT type EHS 6-50Machine -No: 19782 Year 1983Max. Sheet thickness: 6.0 mmCutting length: 5050 mmKnife length: 5100 mmCutting angle: 1 - 15 °Knife strokes per minute: 18Number of hold-downs: 26Pressure p. Hold down: 60 barOperating pressure: 280 barOil filling: 220 lDrive power: 12 kWWeight approx: 11 tOutside dimensions approx: 5500 x 2900 x 2100 mmWith- mot. back gauge 1500 mm with length indicator- Cutting angle indicator- Cutting angle adjustment- Cutting length limit- Footswitchused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

sheet width: 3100 mm plate thickness: 6,0 mm distance between columns: 3.100 mm down holder: 14 Stück no. of strokes: 16 - 24 Hub/min oil volume: 150 ltr. cutting angle: 0,5 - 1,5 ° thickness at Niro-steel: 4,0 mm column arm: 350 mm engine output: 11,0 kW weight of the machine ca.: 7.060 kg range L-W-H: 4,1 x 2,2 x 2,19 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 4100 mm plate thickness: 10,0 mm thickness at Niro-steel: 6,0 mm down holder: 28 Stück no. of strokes: 18 Hub/min oil volume: 260 ltr. cutting angle: 0,5 - 2 ° control: CYBELEC Cybtouch engine output: 22,0 kW back stop - adjustable: 1000 mm range L-W-H: 6100 x 2580 x 2460 mm weight: 15.100 kg. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mm plate thickness: 6,0 mm distance between columns: 3100 mm down holder: 14 Stück no. of strokes: 18 Hub/min oil volume: 150 ltr. cutting angle: 1,2 ° thickness at Niro-steel: 4,0 mm control: CYBELEC CybTouch weight: 6300 kg range L-W-H: 4.000 x 2.100 x 1.640 mm -------------------------------------------------- electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment -------------------------------------------------- Furnishing: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be folded up at max.travel, for longer  ...

Hydraulic sheet metal shears make LOTZE type TS 3000/5machine -No: 2623003 year 1975Technical specifications:Max. Effective length: 3040 mmMax. Sheet thickness steel: 5.0 mmMax. Sheet thickness stainless steel: 3.0 mmOutside dimensions approx: 3750 x 1255 x 1600 mmWith- motor backgauge with handwheel fine adjustment- Cutting length limit- Angle stop front- Table extension- Footswitchused, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Hydraulic swing cut guillotine shears make HERA type HSS 3Machine -No: 557 built in 1984heavy, unbreakable all-steel designTechnical specifications:Passage: 1100 mmLarge sheet thickness at 400 N / mm 2.0 mmThroat: 200 mmNumber of strokes: 56 H / minStop length at the front: 1000 mmStop length at the back: 1000 mmMotor power: 2.2 kWWeight about 1500 kgDimensionswith- motorized backgauge- foot switch- front support arms- hydr. Hold-downused, in good and functional conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

: neu : ca. 12 Wochen ab Auftrags : 1530 mm : 20 mm : 15 mm : 8 1/min : 3 ° : 7 pcs. : 500 mm : 30 kW : 250 l : 950 mm : 2100 mm : 1400 mm : 2000 mm : 6000 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Swing cut sheet metal shears make RAS type 52.31Fabr. -No: 23/7, built in 2000Technical specifications:Cutting range up to: 3100 mmmax.sheet thickness: 2.0 mmNumber of strokes per minute: 37Cutting angle: 0.9 degreesDrive power: 3.0 kWExternal dimensions approx L x W x H: 3580 x 1700 x 1220 mmWeight approx .: 1950 kgwith- CE marking- Angle stop in front- 2 table extensions- foot switch- Single stroke - continuous run- Cut material switch via hand leverwithout back gaugeused, in good and functional conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Fully hydraulic curved roller Shear make PARX type KRS 2Machine -No: 3728 Series 61/72, year of construction 1973Shearing power b. 40 kg / mm2 strength: 6 mmShearing power b. 70 kg / mm2 strength: 4 mmProjection between stand and knife: 1050 mmStand opening height: 300 mmmin Curve radius: 75 mmmin. Rondendiam.:290 / 180 mmMax. Rondendrm. from 4-corner sheet: 2750 mmminute Flaring rim: 450 mmMax. Beading height: 50 mmMax. Beading radius: 35 mmCutting speed stepless: 0 - 12 m / min.Power requirement: 6 hpWeight: 1.85 t (without mandrel centering)Outside dimensions: 3000 x 900 x 2000 mm(without mandrel centering)With- full hydr. drive- graduated Speed control- Const. Starting and working torque- Automatic workpiece feed- Contour cutting (cropping)- Circular section- Spiral cut- Beading- with adjustable Thorn centeringused, from operational resolution, in good conditionPrice on request.Deliv ...

: neu : ca. 12 Wochen ab Auftrags : 1530 mm : 12 mm : 9 mm : 8 1/min : 3 ° : 8 pcs. : 500 mm : 15 kW : 180 l : 950 mm : 2200 mm : 1200 mm : 1800 mm : 3400 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : 1280 mm : 12 mm : 9 mm : 9 1/min : 3 ° : 7 pcs. : 500 mm : 15 kW : 180 l : 950 mm : 1950 mm : 1200 mm : 1800 mm : 3200 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Circular shears make PARX / KUNZ type KSM / 2 / schMachine -No: 3756 built in 1975Technical specifications:Shear capacity 40 kg / mm2 4.0 mmShear capacity 70 kg / mm2 2.5 mmProjection 380 mmGuide curve projection 750 mmgr. round square sheet metal 1000 mm gr.Ronde octagonal sheet metal 1250 mm Flare diameter max. 400 mmFlare height max. 30 mmFlaring radius max. 20 mmCutting speed 15/30 m / minDrive power 2.5 / 3.0 kWWeight approx. 2500 kgDimensions 3600 x 500 x 2200 mmWeight approx. 2500 kgWith- automated with hydr. Adjustment of the circle center point guidancefor different diameters and material tension in the center- complete electr. Facility- Inclined lower knife shaft- swiveling control panel- hydr. Infeed of the upper tool for scissors and guide arch- hydr. Guide arc swivel device- various cutting wheelsused, in good conditionPrice on request.Delivery: ex warehouse or  ...

Motorized crank sheet metal shears make FASTI type 507 15-3.5Machine -No: 84517010 built in 1984Technical specifications:Cutting length: 1540 mmmax.sheet thickness: 3.5 mmAdjustment range of backgauge: 1500 mmStrokes per minute: 56Drive power: 7.5 kWWeight approx: 1610 kgwith- Front-operated motor stop with digital display and 1 dimension preselection- foot switch- single stroke - continuous stroke - jogging- Side stop 750 mm- 2 table extensionsused, in very good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

: neu : ca. 12 Wochen ab Auftrags : 1030 mm : 10 mm : 6 mm : 10 1/min : 3 ° : 7 pcs. : 5000 mm : 11 kW : 100 l : 900 mm : 1550 mm : 1150 mm : 1600 mm : 1900 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 12 Wochen ab Auftrags : 1030 mm : 6 mm : 4 mm : 14 1/min : 3 ° : 7 pcs. : 500 mm : 5.5 kW : 100 l : 900 mm : 1550 mm : 1150 mm : 1600 mm : 1700 kg hydr. drive unit, completely integrated in the machine body overload safety, hydraulic and electrical adjusting of the cutting angle adjusting of the cutting gap blank holder pressure, adjustable support arm with angle stop and scale up to 600 mm 4 rotating knives for VA steel movable pedal switch with solenoid valves manual adjustable and foldable back gauge exchangeable machine table support section area lighting The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Motorized sheet metal shears make RAS type 83.25Machine -No: 27/10Technical specifications:Cutting length: 2540 mmSheet thickness max.: 3.0 mmNumber of strokes per minute: 50Cutting Angle:1.35°Table width: 430 mmTable height: 750 mmlateral projection: 100 mmRear stop adjustment: 550 mmDrive power: 5.5 kWWeight approx.: 2.5 twith- manual backgauge- manual adjustment of the back gauge from the front with reading scale- foot switch- angle stop- support arms- Tilting roller tableused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Angle shears make THEIS type 3/30 - 60 H 80Machine -No: 1085/77, built in 1977Sheet thickness at 42kp / mm: max. : 4 mmCutting dimensions max .: 300 x 600 mmNumber of strokes / continuous stroke without load: 92 / min.Stroke: 26 mmKnife angle: 1.5 °Downholder: mechanicallyOpening width between downholder and knife table: 6 mmHydraulic operating pressure: 300 barOil tank: 300 ltr.Connection voltage: 380 V / 50 HzDrive power: 15 kWDrive power conveyor belt: 0.55 kWOutside dimensions approx: 2200 x 2300 x 2200 mmWith- Front table 200 x 500 u. 200 x 725 mmwith adjustable page rash- Back gauge by hand 0 - 500 mm- Cutting gap adjustment- Conveyor belt with scrap switchused in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer a ...

Motor flat bar shears / bar shears make MUBEA type KFS 20Machine -No: 161/23028/420for rectangular cutting of round, square and flat steelMax. Shear cross section: 4000 mmCutting performance flat: 100 x 36 mmor: 300 x 20 mmwith special tool round: 65 mm: square: 60 x 60 mmStroke rate: 40 hpM.Power requirement: 7.5 hpWeight approx: 2450 kgOutside dimensions approx: 1600 x 1200 x 2700 mmWith- Central lubrication- Footswitchused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

round bar steel: 45 mm square edge steel: 42 mm L-beam: 140 x 13 mm flat steel: 350 x 20 mm pressure: 550 kN throat: 305 mm notching: rectangle tool: mm total power requirement: 5,5 kW weight of the machine ca.: 1260 kg dimensions of the machine ca.: 1360 x 750 x 1565 mm 2 working cylinder with 2 separated electric foot switch for 2-people-handling New notching table, new knife for the rectangle notcher and new punching table included For further information please see brochure. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hydraulic flat steel shears make SANDT type 426 - 72789Fabr. -No: 808407Technical specifications:Knife length: 80 mmcuts steel up to approx: 80 x 6 mmTable size: 350 x 300 mmelectrical connection: 380 V 50 HzExternal dimensions Scissors L x W x H: 200 x 200 x 350 mmOverall dimensions with base and hydraulics: 450 x 360 x 1400 mmWith- Hydraulic compact unit HAWE HC4 / 4,3xa0xa0 1.5 kW, 4.3 l / min, 380 bar- Foot operationused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

sheet width: 2500 mm plate thickness: 12,5 mm distance between columns: mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Width of metal, max. 2,500 mm Metal thickness, max. 12.5 mm Weight, approx. 19,000 kg Drive 40 kW Equipment / Special Features: Adjustment of cutting gap. Hydraulic blank holder. Automatic arrester adjustment for cutting blanks. Program input and piece number input. Transportation device for blanks. Stacking device. This is an ideal machine for cutting lots of small blanks out of large pieces of sheet metal. Machine is equipped with a complex stacking device on the back of the machine. This is a heavy and rigid machine. Condition : Good to very good. Machine can soon be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. Thank you for your interest. The data for th ...

sheet width: 3100 mm plate thickness: 12 mm distance between columns: 3260 mm back stop - adjustable: 3 - 1250 mm power capacity: 37 kW voltage: 400 V weight of the machine ca.: ca. 14 t dimensions of the machine ca.: 4,00 x 4,00 x 2,20 m CNC-controlled plate shear www.kefischer.de The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Automatic circular knife trimming machine make ELMA type E 144 RBuilt in 1995 for horizontal trimming of stamped sheet metal partsTechnical specifications:Table size: 1100 x 800 mmmax.sheet thickness: 3.0 / 2.0 mmStroke max .: 100 mmGear ratio of the shafts: 4max.overhang of the flanges on the topruning part: 335 mmAir pressure max .: 8.0 Kh / cm²Power connection: 220 - 380 V / 50 HzDimensions approx: 2000 x 1300 x 1600 mmWeight about: 500 kgused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Alligator scissors Lindemann Alibo The Lindemann Alibo has a mechanical hold-down. The scissor head is protected with a safety basket. Machine On hand Knife length : 760 mm Weight : 4200 kg Mouth width at the tip : 200 mm Cutting capacity: 0.45 kN/ mm² : Ø 70 mm Number of strokes : 20 – 40 cuts/min Dimensions: 4.20 x 1.50 x 1.80 meters Drive: 15 kw Hold-down: Mechanical

BOSCHERT G CUT 2504 CNC guillotine shears were manufactured in 2014 in Germany. The guillotine is designed for cutting metal sheets with a maximum length of 2600 mm and a thickness of 4 mm (mild steel st42) or 2 mm (stainless steel). The sheet metal is held in place by 13 hydraulic clamps and, thanks to the installed CNC controller with touch panel, it is also possible to store many different work programmes, making the machine very useful and versatile. After entering the parameters of the steel sheet to be cut, the controller automatically sets the cutting gap, choices the angle of the upper knife and the appropriate pressure force and then starts the cutting process. The guillotine is also equipped with, among other things: a foot control to facilitate the operator’s work, light curtains to prevent a worker from entering the working area of the machine and an automatic metal shee ...

The JMC 150 has a mechanically adjustable hold-down. The scissor head is operated with a foot pedal for individual cuts or continuous cutting. The scissor head is protected with a safety basket. The JMC 150 is a tabletop unit for easy handling. Manufacturer: Mc Intyre Knife length: 150 mm Measuring opening: 105 mm Cutting capacity: 25 tons Round iron ST 37: 25 mm diameter Number of strokes at 1/4 aperture: 20 / min Number of strokes at 1/2 opening: 12 / min Number of strokes at full opening: 9 / min Dimensions ( L x W x H ): 660 x 520 x 620 mm Weight: 150 kg Drive: 1.5 kw / 230 Volt Operation: Foot pedal

JMC 900 alligator shears (new machine) The JMC 900 has a hydraulic hold-down. The scissor head is operated with a foot pedal for individual cuts or continuous cutting. The scissor head is protected with a safety basket. Out of stock Delivery time: On request Manufacturer: Mc Intyre Knife length: 920 mm Measuring opening: 473 mm Cutting capacity: 233 tons Round iron ST 37: 88 mm diameter Number of strokes at 1/4 aperture: 26 / min Number of strokes at full opening: 9 / min Dimensions ( L x W x H ): 3200 x 1030 x 1800 mm Weight: 4400 kg Drive: 18.5 kw / 400 V + 1.5 kw electric motor cooler Operation: Foot pedal

Specifications: - working width 2540 mm - max. cutting capacity St 40 4 mm - mot. Cutting angle adjustment - Cut gap. by scaled adjustment screws - Number of hydraulic holders 14 pcs - Mot. backgauge with positioning. 10 - 1000 mm - Stroke rate depending on cutting angle and cutting length 23 per min - Hydraulic drive 400 V / 7.5 kW - Table height 1030 mm - Space requirement approx. W 2500 x H 1630 x D 2150 mm - Weight approx. 3600 kg - with: - Sheet metal holding pneum. supported - front angle stop + support arms - Electronic cutting depth adjustment - Cut line lighting - E-foot switch

ERMAK CNC HVR 3100 x 13 hydraulic guillotine shears built in Turkey in 2008, are designed for cutting workpieces made of among others mild steel or stainless steel. The metal sheet with a maximum length of 3100 mm and a maximum thickness of 8 mm (plain steel) or 13 mm (stainless steel), is held during machining by 14 hydraulic clamps. The angle of the cutting blade can be freely adjusted in the range from 0.5° to 2.0°. Full control over the operation of the CNC HVR 3113 machine is guaranteed by the control panel located on the guillotine shears body with installed CYBELEC DNC 60 CNC controller, allowing programming of many different machining processes. The guillotine shears is equipped with among others new cutting blades and a foot control pedal, making the operator’s work much more comfortable and simple. The total weight of the machine is 13400 kg. The total weight of the mach ...

Hand lever plate shears and profile steel shears Knife length 400mm Cuts sheets up to 5mm Cuts round steel up to 13mm Heavy and stable design with foldable storage table. Mounted on base More hand lever plate shears in stock, also for round steel and profiles!

sheet width: 3100 mm plate thickness: 13,0 mm thickness at Niro-steel: 8,0 mm down holder: 14 Stück no. of strokes: 11 Hub/min oil volume: 310 ltr. cutting angle: 2,0 ° throat: 350 mm table height: 900 mm total power requirement: 22,0 kW weight of the machine ca.: 12200 kg range L-W-H: ca. 4100 x 2300 x 2235 mm -------------------------------------------------- heavy electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment -------------------------------------------------- Furnishing: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom ...

High-quality, PLC-controlled circular shears / circular, blank and flange ring shears with punching device used - refurbished PLC – Control for 120 cutting programs with 30 program sets each Projection in tailstock 1,000 mm Automatic tailstock clamping Outreach in the shear station 400 mm Shear performance 0.5 to 5 mm sheet steel 400 N/mm² 0.5 to 3 mm stainless steel sheet 650 N/mm² Largest shearable disc diameter Ø 1,400 mm for rectangular starting material Ø 1,800 mm for octagonal starting material Smallest shear diameter 150 mm Diameter Ø shear knife 100 mm Shear rate up to 35 m/min punching diameter at S = 2 mm sheet steel 400 N/mm² - Ø 25 mm at S = 3 mm sheet steel 400 N/mm² - Ø 17 mm Drive power 7 KW Weight 1.300 kg Dimensions 2.7 x 1.8 m x H 1.7 m Optionally available with a flanging device – Maximum board height 20 mm Large ...

sheet width: 3100 mm plate thickness: 10,0 mm thickness at Niro-steel: 6,0 mm down holder: 14 Stück no. of strokes: 13 Hub/min oil volume: 260 ltr. cutting angle: 2,0 ° throat: 350 mm engine output: 22,0 kW back stop - adjustable: 1.000 mm weight: 10.575 kg. range L-W-H: 4,05 x 2,5 x 2,17 m -------------------------------------------------- heavy electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment -------------------------------------------------- Furnishing: - CNC electr. / hydraulic swing cut shears - CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting - motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be folded up at max.trav ...

swing beam Cutting length: 4100 mm Max sheet thickness st 45: 6 mm Backgauge: no backgauge