134,838 used machines on RESALE, but how to find them? Machine Search
angle steel/side length: unbkt. mm double T-iron on the x-axis: unbkt. mm U-iron on the x-axis: unbkt. mm total power requirement: 30 kW weight of the machine ca.: 8,6 t dimensions of the machine ca.: 2500x2000x1900 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: siehe TD mm plate thickness: siehe TD mm pre-bending: 16mm total power requirement: 22 kW weight of the machine ca.: 16,65 t dimensions of the machine ca.: 5560 x 2060 x 2050mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 2500 mm plate thickness: 30 mm pre-bending: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Stocknumber 2210015 Type of machine Hydr. 3-roll bending machine Make HAUSLER Type RMA 2500/30 Build in 1962 Type of control conventional Additional information max. widht 2500 mm Max. plate thickness 30 mm 3 rolls diameter upper oll 450 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3554 mm plate thickness: 42 mm pre-bending: 36 mm Control: total power requirement: kW weight of the machine ca.: 49 t dimensions of the machine ca.: 7.3x2.4x2.5 m Stocknumber 2210024 Type of machine 4-roll CNC Plate bending machine Make FACCIN Type 4HEL 3554 Build in 2000 Type of control CNC Additional information Cap. 3554 x 42 mm prebending 36 mm Toprolldiam. 540 mm underrolldiam. 530 mm siterolldiam. 430 mm 55 Kw LxWxH= 7350 x 2400 x 2500 mm weight of the machine 49 ton The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3050 mm plate thickness: 53 mm pre-bending: 45 total power requirement: 60 kW weight of the machine ca.: t dimensions of the machine ca.: m Stocknumber 2210020 Type of machine 4-Roll Plate Bending machine Make DAVI Type MCB 3053 Build in 1998 Type of control Conventional Additional information max. Plate widht 3050 mm Max. plate thickness 53 mm Max. thickness prebending 45 mm Toprol diameter 525 mm under roll diam. 470 mm Site rolls diam. 400 mm Power 78 Hp Hardened rolls Conical bending Dimensions: 6000 x 3100 x 6700 mm in very good condition The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
HEIDELBERG Nela Plate Bending suitable for HD SM 52 / 74 /102 and XL machines different years of construction available
Key data: 40 , 200 , 1340
The all-electric servo bending machine is one of the products with independent intellectual property rights developed by our company. Special high-load screw and guide rail structure, imported bearing installation, high load-bearing capacity, high positioning accuracy, long life, machine tool rigidity, precision retention, and reliability are close to perfection. By introducing advanced design concepts and scientific design methods, the shortcomings that traditional designs cannot avoid have been solved. This bending machine is fast and simple to program, can realize concurrent linkage of multiple axes, fast feed positioning, and significantly improves the efficiency, accuracy and consistency of bending, which is far superior to traditional hydraulic bending machines, and does not require the use of hydraulic oil, is environmentally friendly and pollution-free. Compared with traditional ...
Schroeder & Bauer WB 32-1 Universal wire and belt bending machine Wire feed Plain text display Press force monitoring Wire straightener Bosch stripping devices Bracket and brush motor with mounted tool W32/1-32 Soundproof cabin Fäßerb CU wire with stamped parts Switchboard Item condition: very good Description of the manufacturer, deviations possible. You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines
sheet width: 2020 mm plate thickness: 2 mm distance between columns: 2030 mm bending angle max.: 135 ° total power requirement: - kW weight of the machine ca.: 1,22 t dimensions of the machine ca.: 2,5 x 1,0 x 1,4 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
SCHNELL SHEAR LINE 300 rebar cutting and bending line was built in 2008 in Italy by Schnell S.p.a. The electrical installation was overhauled in 2024. The SCHNELL SHEAR LINE 300 is a reliable system designed for serial machining of rebar with a maximum diameter of 50 mm. It integrates all the necessary equipment that is responsible for cutting, bending, optimising, storing and handling bars. The entire production cycle, from feeding to the collection of the finished parts, is performed fully automatically. The SCHNELL SL 300 stirrup production machine is fully complete and consists of the following components: – control console – FA/6/14 storage rack for steel – SCHNELL CGS 300 HDY guillotine shears – SCHNELL VBM 12/2 measuring and cutting track with single-sided unloading – SCHNELL ROBOMASTER 45 automatic rebar bending machine – rebar storage and retrieval system ...
GM-SB-38CNC-2A1S mandrel bending machine was built in 2022 in China by ZHANGJIAGANG KING-MACC MACHINERY MANUFACTURING CO., LTD. The machine is used for precision bending of bars, profiles and tubes with a maximum diameter of 38 mm. The process is performed by means of a reliable working head, operating in manual or automatic mode. In order to guarantee high positioning dynamics combined with excellent positioning accuracy, all axes are equipped with powerful servomotors. Ease of operation is ensured by a convenient operator panel with PLC control. Its large memory enables the storage of up to 200 working programmes, as well as the rapid programming of even the most complex shapes. All this makes the GM-SB-38CNC the perfect solution for any production facility. The GM-SB-38CNC-2A1S tube and profile bending machine weighs 2000 kg. Technical specifications of the GM-SB-38CNC-2A1S tube be ...
Inv. Num. : 5725 Type: A 89 TNCB Producer: CSM Created: 2014 Parameters: Maximum bending angle: 180 pcs Total power requirement: 15 kW The largest profile: 60x60x6 mm bending radius in the middle of the tube: 350 mm bending radius in the middle of the profile: 300 mm Machine height: 1200 mm Machine length: 4700 mm Machine width: 1200 mm Machine weight: 2500 kg
chamfer lenght: 0900 mm plate thickness: mm distance between columns: 900 mm pressure: 20 t column arm: 230 mm stroke length max.: 150 mm travel -x axis: 350 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3000 mm plate thickness: 50 mm pre-bending: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
• 3000w IPG with Picking • Sorting Unit LSR & Combo Storage H38 • Large Format 3000 x 1500mm • Year 2014 • Servo Electric - High Speed 30 Ton Punching Head • ONLY 535 HOURS!
Omschrijving Lengte mm Aantal Bovenmes H=66,5mm, R=0,8 85gr 835 2 Bovenmes H=66,5mm, R=0,8 85gr 415 2 Bovenmes H=66,5mm, R=0,8 85gr 300 1 Bovenmes H=66,5mm, R=0,8 85gr 150 1 Bovenmes H=66,5mm, R=0,8 85gr 50 1 Bovenmes H=66,5mm, R=0,8 85gr 40 1 Bovenmes H=66,5mm, R=0,8 85gr 20 1 Bovenmes H=66,5mm, R=0,8 85gr 15 2 Bovenmes H=66,5mm, R=0,8 85gr 10 1 Bovenmes H=66,5mm, R=0,8 85gr LEFT 100 1 Bovenmes H=66,5mm, R=0,8 85gr RIGHT 100 1 Ondermatrijs V10, R=0,8, 85gr 835 2 Ondermatrijs V10, R=0,8, 85gr 415 2 Ondermatrijs V10, R=0,8, 85gr 300 1 Ondermatrijs V10, R=0,8, 85gr 150 1 Ondermatrijs V10, R=0,8, 85gr 50 1 Ondermatrijs V10, R=0,8, 85gr 40 1 Ondermatrijs V10, R=0,8, 85gr 20 1 Ondermatrijs V10, R=0,8, 85gr 15 2 Ondermatrijs V10, R=0,8, 85gr 10 1 Totaal 26 Price € 2250,-- New prijs € 3250,--
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
Unbek. Type, YOC ca. 1990, Revision 2002 Specifications: - Bending capacity at 45 kg / mm² up to approx. Ø 25 x 3 mm - Bending angle left + right selectable - Hydr. Double-sided bending function - Hydr. Delivery ° - Drive 400 V / 11 kW - Space requirement approx. W 1750 x H 2200 x D 2300 mm - Weight approx. 1600 kg - with - bending angle adjustment - Hydr. Voltage - Bending tools
WEGENER BM 301 plastic bending machine was built in Germany by Wegener International GmbH. The machine was regularly maintained and upgraded throughout its service life. In 2022, a general overhaul was carried out at the machine manufacturer. WEGENER BM 301 is the perfect choice for precision forming of thermoplastic sheets made of, among others, PVC, PC/ABS and PMMA with a maximum thickness of 15 mm and a width of 3050 mm. The machining process is performed by means of heating elements in the form of a lower flat strip and an upper V-shaped strip, which heat the material at a controlled temperature to a plastic state. The material is then bent to the desired angle between 0° and 110°. The use of the highest-quality heating elements ensures efficient and even heating of the material along the bending line. They are moved manually along hardened steel rollers. Repeatable positioni ...
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...
MEP Multimatic SA8, year of construction 1995 Straightening and cutting system for reinforcing steel, fully automatic, complete functional system, immediately available Plant still in operation and can be demonstrated.
Ring bending machine, profile bending machine, three-roll bending machine, bending machine, pipe bending tool -Manufacturer: Perthel, pipe bending tool for profile bending machine -Profile diameter: Pipe size 16 - 76 mm / 3/8 to 3 1/4 -Dimensions: 1020/310/H170 mm -Weight: 28 kg
Base for press brake tool, bending tool, die, bottom knife, lower tool, prism tool, reversible prism, 1-piece die block for die bending machine, die tool, folding tool -Tool: for press brake, base for press brake tool -Dimensions: see drawing in the photos -Dimensions: 2500/70/H22 mm -Weight: 26.1 kg
Bending tool, die, upper blade, upper tool, deer foot tool, deer foot tool for press brake -Tool for: Press brake -Dimensions: 3000/30/H116 mm -Weight: 48 kg
Ring bending machine, profile bending machine, three-roll bending machine, bending machine, pipe bending tool -Pipe bending tool: 2 pieces -Profile diameter: 65/49 mm -Recording: dimensions see photos -Price: complete -Dimensions: 195/400/H220 mm -Weight: 42.7 kg
Ring bending machine, profile bending machine, three-roll bending machine, bending machine, pipe bending tool -Pipe bending tool: 2 pieces -Profile diameter: 27/21 mm (pipe size 3/4 /1/2) -Socket: Ø 39 mm -Price: complete -Dimensions: 145/140/H75 mm -Weight: 3.8 kg
sheet width: 300 mm plate thickness: 2,5 mm distance between columns: 300 mm diameter of upper rolls: 32 mm total power requirement: Handbetrieben weight of the machine ca.: 15 Kg dimensions of the machine ca.: 500 x 300 x 150 mm Sheet bending machine with: - Capacity 1050 x 2 mm - High strength wrought iron rollers with SAE 1050 certificate. - Footswitch - conical bending - Swiveling top roller - Safety device emergency leash - Documentation - 400 volts - CE certificate The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 30 / 900 mm : 30 / 900 mm L-beam: 35X35X5 / 600 mm T - beam - web outwards: 50x6 / 600 mm Axis diameter: 40 mm work speed: 4,5 m/min roll diameter: 148 mm total power requirement: 1,1 kW weight of the machine ca.: 0,3 t dimensions of the machine ca.: 0,75 x 0,6 x 1,4 m Electric profile roller - Either horizontal or vertical working - 1 set of hardened standard rollers - lower 2 rollers are driven - 1 set of plastic rollers for diameter 33.7mm / 1 - Operation manual - Foot switch left / right and EMERGENCY STOP The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Ring bending machine, profile bending machine, three-roll bending machine, bending machine, pipe bending tool -Pipe bending tool: 2 pieces -Profile diameter: 1x 40 mm, 1x 60 mm -Socket: Ø 32 mm -Price: complete -Dimensions: 130/270/H115 mm -Weight: 8.1 kg
Ring bending machine, profile bending machine, three-roll bending machine, bending machine, pipe bending tool -Pipe bending tool: 3 pieces -Profile diameter: 1/2 1 1 1/4 , dimensions see photos -Socket: Ø 25 mm -Price: complete -Dimensions: 490/540/H190 mm -Weight: 8 kg
Ring bending machine, profile bending machine, three-roll bending machine, bending machine, pipe bending tool -Pipe bending tool: 6 pieces -Profile diameter: 32 to 80 mm, see photos -Socket: Ø 36 mm -Price: complete -Dimensions: 490/540/H190 mm -Weight: 50.1 kg
round material: 30 x 1 mm square material: 30 x 30 x 1 mm : 16 mm : 30 x 10 mm speeds: 9 U/min total power requirement: 1,1 kW weight of the machine ca.: 0,32 t dimensions of the machine ca.: 0,82 x 0,60 x 1,26 m Electric roller profile with - 5 set of rollers 2x 20mm and 30mm for round material, 1x for flat material 1x for square material 1x for? - footswitch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
1 Wire bending machine OMCG date 1997 technical status good , soft ware to be refurbished 2.Tube bending machine OMCG date 1998 technical status good, software to be refurbished
Bending tool, die, upper blade, upper tool, straightening tool -Tool for: Press brake -Prisms: 90° x 75 mm -Dimensions: see drawing in the photos -Dimensions: 2500/270/H175 mm -Weight: 188 kg
Beading tool, punching tool, separating tool, punching tool, punch, punching die, punching punch -Punching tool with: bending function -Admission bolts: 50 mm -Dimensions: 495/495/H430 mm -Weight: 282 kg
Ring bending machine, profile bending machine, three-roll bending machine, bending machine -Outer diameter: 200 mm -for: 35 mm pipe -Bearing seat: Ø 55 mm -Bore: Ø 49 mm -Quantity: 2 rolls available Price: complete -Dimensions: Ø 200 x 81 mm -Weight: 11 kg
4-column punching tool, cutting tool, punching tool, punch, punching die, punching punch, -Punching tool with: bending function -Admission imensions: 300/205/H445 mm -Weight: 100 kg
CRIPPA CNC YEAR 2007 LOW WORKING HOURS INCLUDED TOOLINGS AND EQUIPMENT WE ORGANIZE FOR CLIENT AS WELL TRANSPORT
4-column punching tool, cutting tool, punching tool, punch, punching die, punching punch, -Punching tool with: bending function -Take bolt: 40 mm -Dimensions: 255/205/H210 mm -Weight: 25 kg
Equipment: 1 sledge feeder on the right 3 press modules á 180 kN = 540 kN 4 normal carriage units 1 narrow carriage unit Workspace: Wire thickness range: up to 10 mm Belt width: up to 100 mm Feed length: up to 250 mm Power: up to 132 rpm
sheet width: 1550 mm plate thickness: 4,5 mm pre-bending: 4,0 mm roll length: 1550 mm min. dia.: 190 mm roll diam. toproll: 130 mm weight: 1265 kg dimensions: 2670x1110x1050 mm Domestic equipments: - Central rollers via electric motor, planetary reduction gear and Gear drive driven - Swivel top roller - Main engine with brake device - Conical bending device - Mobile controller and foot pedal - CE mark / Declaration of Conformity Additional equipment: - induction hardened rolls - motorized rear roller adjustment - Digital display for back roller The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Swivel bending machine, edge bench, gutters, roof gutters, beading machine, beading machine -Max. Working width: 1280 mm -Max. Sheet thickness: 1.75 mm -Opening width: 180 mm -Clamping via: threaded spindle -Bending angle adjustable via: stop -Dimensions: 1850/600/H1240 mm -Weight: 380 kg
Precision bending beam for glass cutting table, glass cutting table, glass cutting machine -Manufacturer: INNOLAS S100-5N -Type: NJ Y123/101 -Weight: 0.1 kg
Bending tool, die, upper blade, upper tool, straightening tool -Tool for: Press brake -divided -Tool: 30° -Dimensions: 196 x 26 mm -Total length: 2997 mm -Lengths: 1x 390/4x 500/1x 607 mm -Weight: 102 kg
Equipment: 1 sledge feeder on the right 1 two-point eccentric press 70 kN 4 normal carriage units 1 narrow carriage unit Workspace: Wire thickness range: up to 3.5 mm Bandwidth: up to 32 mm Feed length: up to 170 mm Power: up to 250 rpm
Bending tool, die, upper blade, upper tool, straightening tool -Tool for: Press brake -Tool: 70° -Thickness: 30 mm -Total length: 475 mm -Lengths: 95/109/112/159 mm -Overall height: 193 mm -Weight: 18 kg
Bending tool, die, upper blade, upper tool, straightening tool -Tool for: Press brake -Tool radius: 3 mm -Thickness: 25/6 mm -Total length: 572 mm -Overall height: 192 mm -Weight: 16 kg
Bending tool, die, upper blade, upper tool, straightening tool -Tool for: Press brake -Tool for: closing folds -Thickness: 25 mm -Total length: 470 mm -Overall height: 195 mm -Weight: 18 kg
maximum number of results exceeded
please refine your search
