bending machine used for sale

Bending semi-automatic, tube bending machine, mandrel bending machine MOBITEC type BAH 1-2 KOTTMANN und BERGER GmbH Fabr. No. 056 Year of manufacture 09/2004 - for simultaneous bending of two steel pipe sections up to 12 mm bending angle max. 90 Tube diameter max 12mm Mandrel length approx. 65 mm Nominal power 3.5 kW Compressed air max. 6 bar / approx. 1 litre per bending cycle Mains connection 400 volts, 50 Hz - Pneumatic clamping - Pneumatic mandrel retraction - Control for angle input via STOBER Controlbox Series 4000/5000 - Control SIEMENS S7-200 with display TD200 - Machine without bending tools and without tool bearing bolt 25 x 183 mm - only 1 bending mandrel available (see pictures). Space requirements L x W x H 1000 x 1000 x 1500 mm Weight 390 kg good condition; used

Swivel bending machine, cant bench, gutters, roof gutters, beading machine, beading machine, three-roller round, three-roller sheet metal bending machine, bending machine, sheet metal round bending machine, 3-roller round bending machine, profile bending machine, three-roller sheet metal rolling machine -Swivel bending machine: with 3-roller bending machine on a solid base -Max. Working width: 1020 mm -Max. Sheet thickness: 1.5 mm -Roller diameter: 2x 50 mm / 1x 53 mm -Dimensions: 1450/800/H1155 mm -Weight: 346 kg

Hand - Swivel bending machine KRAMER type AMS 650 x 1.5 Hand swivel bending machine, bending bench Year of construction approx. 1985 Working length 650 mm Sheet thickness at 40 kg/mm2 1.5 mm Upper cheek opening approx. 60 mm Bending cheek adjustment approx. 0-25 mm Bending angle 0-180- Upper cheek adjustment via hand crank - Pre-screw rail for the bending clamp - one-piece sharpening rail 135 Space requirement L x W x H 1200 x 600 x 1100 mm Weight 160 kg good condition; used

Bending tool, matrix, upper knife, upper tool, upper beam -Bending tool: from Lotze HDZ swivel bending machine -Length 2678 mm -Hole spacing: 100mm M10 -Dimensions: see the drawing in the photos -Dimension: 2678/6/H45 mm -Total weight: 5,6 kg

Bending tool, matrix, upper knife, upper tool, upper beam -Bending tool: from Lotze HDZ swivel bending machine -Length 2678 mm -Hole spacing: 100 mm M10 -Dimensions: see the drawing in the photos -Dimension: 2678/15/H57 mm -Total weight: 15.7 kg

Bending tool, die, lower knife, lower tool, lower beam -Bending tool: from Lotze HDZK swivel bending machine -Widening: for lower cheek -Dimensions: 2487 x 100 x 15 mm / 190 x 100 x 15 mm -Hole spacing: 100 x 18 mm -Transport dimension: 2487/100/H30 mm -Total weight: 29.4 kg

Upper tool - bending tool for die bending machine GEWA Press brake set: 15 pieces Type: GWP-1291 Angle: 88 Radius: 0.8 mm Segment height: 200 mm max. pressure per meter: 85 t/m Total length of the 15 segments: 4010 mm Segment lengths: 6 x 505 mm, 1 x 400 mm, 1 x 190 mm, 1 x 100 mm, 1 x 69 mm, 1 x 58 mm, 1 x 48 mm, 1 x 42 mm, 1 x 40 mm, 1 x 33 mm Total height with tool holder: 230 mm Tool holder: 30 x 13 mm, 8.4 mm groove Weight: 260 kg very good condition Suitable lower tool under stock number 60752. Tool set suitable for AMADA, TRUMPF and LVD press brakes with appropriate tool system; used

Bending tool, die, upper knife, upper tool, straight tool, upper beam -Bending tool: for folding machine -Tool angle: 45° -Dimensions: see the drawing in the photos -Dimension: 47 x 11mm -Length: 945mm -Weight: 3.5 kg

Bending tool, die, upper knife, upper tool, straight tool, die tool, seam closing tool -Tool: for folding machine RAS Typ 74.30 -Dimensions: see the drawing in the photos -Distance recess rail: center center 650 mm -Dimension: 3060/28/H121 mm -Weight: 65kg

unknow A9020411 (12-14)-

Operator Panel

unknow GE.570205.0002.00, part of the set-

Main Rack

BARCO HULPFUNCTIE 16 DIG OUTP

BARCO FLOPamp;KBRD INTF MNC95

Bending machine FAVRIN 3100×30 PHLS CNC (A3708) Type: hydraulic Max worklength: 3100 mm Eletric motor (power) 75 HP Courant needed 380V Weight 32 ton Machine was previously used to bend Hardox workpieces. bending capacities examples: – 3100 x 25 mm > multi stage bending for large radiuses – 2500 x 30 mm > multi stage bending for large radiuses – 3100 x 17 mm > single stage bending – 2500 x 25 mm > single stage bending full CNC corner + backgauge control upper hydraulic clamping of tools clamping force: 220 ton max bending angle: 110° max open: 500 mm Tooling included for radius bending Also 2 new extra cilinders included

Standing seam metal roof machine F3 Standing seam metal roof machine F3 with length measuring device was designed by our company to produce standing seam roofing panels for the installation of roofs and facades of various buildings and structures. Sheet metal blanks are passed through the forming rolls of the machine to get the desired shape of the standing seam panel. This method of production allows you to produce panels with a speed of about 10 meters per minute and fit any roofing companies. The machine is equipped with an easy width adjustment system, so it takes just a few minutes to readjust it from rolling one width to another. The F3 machine can work with panels from 200 to 700 mm wide. It is possible to work with metal sheets and coils made of galvanized steel, copper, zinc, aluminum, stainless steel, etc. Maximum metal thickness for work – 0.8 mm. Standing s ...

Profile bending roll used equipment hydraulic model AR200 year 2008 make MG Italy Capacity bending chart photo in enclosed -Technical data: Output shafts size 200 mm -Machine complete with set of rollers adjustable for the various shape of profiles. -Traction tool hydraulic operated for the HEB-beam - IPE - UNP bending the hard side. -Lateral correctors left and right side hydraulic operated in 3 direction. -Included additional set of rolls for pipe 6" inches -Machine with 3 rolls driven system with individual hydraulic motor and axial gear-unit on each shaft. -The 3 shafts working on bearings, heavy duty type with sealed lubrication. -Centralized control panel movable on wheels with all electric commands. -Dual rolling speed up to 5 mtr/min with automatic balancing system between the 3 rolls. -Safety devices in compliance with European regulation. CE mark. - ...

SHUZ TUNG CNC 50 BRM CNC tube and profile bending machine built in 2014 in Taiwan allows for fully automatic, serial production of complex spatial workpieces in 5 axes with simultaneous hole punching. Excellent precision and accuracy of bending are guaranteed by the reliable servo motors used in the machine, which are responsible for realising the main working movements, i.e. bending, rotation and material feed. The rest of the movements are driven by a central hydraulic system with electronic lubrication. The SHUZ TUNG CNC mandrel bending machine is operated via a control panel with an installed CNC controller with the option of saving an unlimited number of programmes. In addition, the automatic servo bending machine is equipped with several bending rolls, a high-quality mandrel and an actuator to support material feed. The 50 BRM automatic CNC mandrel bending machine weighs 3500 kg ...

ZREMB GH4 tube bending machine, manufactured in 1983, is used in factories during the precise processing of all varieties of installation tubes. The tube bending is performed in a semi-automatic mode on a cam with the mandrel filling the most deformed section of the tube. The machine comes with a comprehensive range of equipment shown in the accompanying photos. The GH4 mandrel bending machine weighs 2450 kg. The ZREMB tube bending machine consists of: – drive mechanism – mandrel feed mechanism – guiding mechanism – control panel mechanism – hydraulic system – electrical installation assembly – frame assembly Technical specification of the ZREMB GH4 bending machine - tube diameters: 1 ½”; 2″, 2 ½”; 3″, 3 ½”; 4″ - maximum bending angle: 180° - bending capacity (30 bends): 180°/h - head working movement time (180°): 38 s - head return movem ...

Automatic 3D wire bending machine was manufactured in Poland in 2022. The machine is used to automatically bend cut wire with a diameter of 4 to 8 mm. The structure made of thick-walled steel profiles, together with high-quality components, guarantee high bending precision and reliable operation. The automatic wire bending machine is equipped with a bending head with carriage and grippers and a wire feeding module consisting of a cut wire magazine and a selector mechanism. The workpiece taken from the magazine with a capacity of 150 kg, is fed via the wire selector mechanism into the feed channel, where it is pushed into the bending head and processed. At the end of the process, the bent wire falls into a receiving hopper or support table. All the capabilities of the wire bending machine are controlled by an installed PLC with an intuitive interface, taking care of the performance  ...

sheet width: 1020 mm plate thickness: 2,0 mm daylight opening: 48 mm bending angle max.: 0 - 135 ° work height max.: 900 mm total power requirement: von Hand kW weight of the machine ca.: 285 kg dimensions of the machine ca.: 1350 x 820 x 1140 mm Furnishing: - Segmented upper and bending beam for a wide variety of bending options - Clamping by means of a foot pedal - Hands remain free for optimal positioning of the sheet - Universally applicable bending machine for plumbing and repair shops - Robust construction in a modern design - Manual bending machine for standard bending tasks - Segmented upper beam for a large number of bending options - Optimal price-performance ratio - Quick and easy bending process using a bow handle - Non-slip rubber coating on the foot pedal for safe working - Easy adjustment of the lower beam to the respective sheet thickness - High upper beam for producing  ...

The bending machine is intended for bending installation pipes of all varieties: light, medium, heavy with diameters: 1 ½”; 2”, 2 ½”; 3, 3 ½; 4. Range of bending angles - up to 1800. Arches are bent cold. The bending cycle is semi-automatic, which facilitates high efficiency. The GH-4 bending machine has a hydraulic drive for the working movement and auxiliary movements. The bending of the pipe takes place on a cam while filling the most deformed pipe cross-section with a mandrel. The bending machine consists of the following mechanisms and assemblies: 1. driving mechanism 2. guiding mechanism 3. control panel mechanism 4. hydraulic installation 5. electrical installation assembly 6. frame assembly 7. pin feed mechanism Bending machine weight: 2450 kg Dimensions: length – 4620 mm; width – 1240 mm; height – 1420 mm; Installed power – 5.5 kW. bending ca ...

Original MINGORI® Model OB40 - Mobile hydraulic tube bending machine with manually operated hand pump, suitable for bending pipes according to DIN, API and ASA standard, as well as coated PE-HD pipes. The machine works in the compression bending process. The greatest surmountable material resistance torque that can be overcome with the machine is about 28 cm³. Maximum bending force 18 tons Maximum bendable pipe diameter 88.9 mm Smallest possible bendable pipe diameter 17.2 mm Smallest bending radius depending on the radius of the bending punch from 46.5 mm to 330 mm Smallest bending angle 110° (this machine also available for bending angles up to 180°) Weight of the basic machine approx. 140 kg The machine is delivered in a storage chest – Dimensions of the chest approx. 102 x 32 cm x H 41 cm Weight basic machine 140 kg With electrically operated hand pump (as mo ...

MACRI ITALIA PROVAR 6-45 U-D bending machine was manufactured in 2019 in Italy. The fully automatic mandrel bending machine is used in the process of machining tubes and profiles with a maximum diameter of 45 mm in 6 numerically controlled axes (X, Y, Z, B1, B2, A). Excellent process stability and workpiece quality, with the possibility of bending standard and variable (free) radiuses, are guaranteed thanks to the robust steel construction, the moving head with high-strength gears and the equipping of all machine axes with brushless servomotors. The MACRI PROVAR 6-45 U-D CNC tube bending machine is controlled using state-of-the-art MACRI software with the ability of importing files from 3D programmes and performing an anti-collision test with 3D simulation, programming of positioner force and automatic mandrel lubrication and many other useful functions. The total weight of the machi ...

MACRI ITALIA PROVAR 5-90 U-D tube bending machine, built in Italy in 2010 is used for the fully automatic process of fixed radius and variable radius workpiece bending on two different dies. The machine is characterised by a highly rigid steel structure, modern components and extensive equipment. All 5 axes of the machine (X, Y, Z, B1, B2) are equipped with reliable brushless servomotors in order to provide the user with high dynamics and excellent positioning accuracy when machining tubes and profiles with a maximum length of 5100 mm. The installed state-of-the-art MACRI software allows, among others, to program the positioner force, perform an anti-collision test with 3D simulation, import files from 3D programmes and program the speed of movement of each axis for each bend. The PROVAR 5-90 U-D mandrel bending machine weighs 6000 kg. Technical specifications of the MACRI ITALIA PROV ...

Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic CNC – controlled double-sided pre-bending – conical bending device, three hydraulically driven rollers (one hydraulic motor per roll), hydraulic linear sub-roll adjustment – hard chrome-plated piston rods – hardened and ground rollers - PILZ® laser protection - BECKHOFF® CNC – control with Ethernet technology and large touch screen - DANFOSS® precision hydraulics – central lubrication system Maximum bending length 2,000 mm Roll diameter 170 mm Smallest weft diameter = 1.1 x the roll diameter The rollers run in bronze plain bearings. Nominal pre-bending performance over the entire bending length at 5 x D = 5 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 7 mm sheet steel/ST40 Drive power  ...

Very high-quality CNC – controlled precision sheet metal round bending machine with automatic bending sequence calculation – automatic CNC – controlled double-sided pre-bending – conical bending device, three hydraulically driven rollers (one hydraulic motor per roll), hydraulic linear sub-roll adjustment – hard chrome-plated piston rods – hardened and ground rollers - PILZ® laser protection - BECKHOFF® CNC – control with Ethernet technology and large touch screen - DANFOSS® precision hydraulics – central lubrication system Maximum bending length 2,000 mm Roll diameter 170 mm Smallest weft diameter = 1.1 x the roll diameter The rollers run in bronze plain bearings. Nominal pre-bending performance over the entire bending length at 5 x D = 5 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 7 mm sheet steel/ST40 Drive  ...

Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...

Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...

Very high-quality CNC – controlled precision sheet metal bending machine with automatic bending sequence calculation – automatic, CNC – controlled double-sided pre-bending – conical bending device Roll diameter 350 mm Smallest weft diameter 1.1 x the roll diameter = 385 mm Maximum bending length 3,000 mm Nominal pre-bending performance over the entire bending length at 5 x D = 18 mm for sheet steel/ST40 Nominal bending performance over the entire bending length at 5 x D = 22 mm sheet steel/ST40 Drive power 22 kW Weight 13,500 kg. Three hydraulically driven rollers (one hydraulic motor per roller) - The rollers run in bronze plain bearings Hydraulic linear sub-roller adjustment Hard chrome-plated piston rods Hardened and ground rollers PILZ® Laser Validation BECKHOFF® CNC – Control with Ethernet technology and large touch screen DANFOSS® Precision Hydraul ...

Ring bending machine, profile bending machine, bending machine, pipe bending tool, tube bender, tube bending machine, mandrel bending machine -Mandrel bending machine: mechanical profile bending machine -Accessories: see photos -Total dimensions: 1200/740/H1220 mm -Weight: 169 kg

: 50 mm roll diameter: 150 mm revolutions per minute: 10 U/min adjustments: 120 mm total power requirement: 1,5 kW weight of the machine ca.: 430 kg dimensions of the machine ca.: 1,2 x 0,8 x 1,75 mm The PB 50-3 H is a hydraulic profile bending machine: we produce thisprofilebender in Europe and deliver it directly from our stock. This hydraulic profile bending machine has a shaft diameter of 50 mm and 3 driven rolls. It is easy to switch between working with two or three driven rolls via the gearshift on the side of the machine. Operation of the profile bender is done by a foot pedal and with the pedals you choose the turning direction of the rolls. Our PB 50-3 H has a handpump to adjust the position of the upper / centre roll with hydraulics. The position of this upper roll can be read out on a scale and on the digital display (0,1 mm). Furthermore, our Profi Bend machines can work in  ...

Profile ring bending machine Make O.L.B. Machinery Type RBM 3/60 SA Year of construction 2015 Shaft ø 60 mm max. bending roller ø 215 mm Bending capacity max. - square 50 x 50 mm Bending capacity max. - flat 80 x 15 or 120 x 25 mm Bending performance max. - angle 70 x 70 x 7 mm Bending capacity max. - round ø 50 mm Bending capacity max. - round ø 100 x 2 mm Number of driven shafts 3 Total power requirement 2.6 kW Machine weight approx. 1.2 t Dimensions of the machine L x W x H 1.2 x 0.85 x 1.53 m - all 3 shafts driven - Absolutely new condition Accessories 3 sets of bending rollers

Electro-hydraulic. Mandrel bending machine Fabr. LANG type EL-OR 50Machine -No: 4125 built in 1981Max. Pipe diameter at 40 kg mm²Radius 3 x outer pipe diameter: 50 x 2 mmMax. Bending radius up to middle pipe: 200 mmminute Bending radius up to inner pipe edge: 35 mmMax. Pipe insertion length: 3000 mmMax. Bending angle: 180 °Bending head speed: 14 rpmtheoretical number of sheets 90 / U.: 900Drive power: 7.5 kWWeight approx: 1800 kgDimensions approx: 4000 x 1300 x 1200 mmWith- Hydraulically powered and working automatically- bending table drive- Tube clamping device with infinitely adjustable clamping pressure- Dornrückzugseinrichtung- Automatic bending roller return device- Hand-operated length stop device- Bend angle selector for settingxa0xa0 4 different bending angles- automatic mandrel lubrication device- Use of running counter-pressure slide rails- Footswitch- without toolsused, in ...

Three-roll sheet bending machine, used three-rollers -plate -bending m/c, used Type: UBBD 2.5 x 2000 Manufacturer / make: WMW Built/ new: 1970 Working range: sheet width max. / max. working length: 2000 mm Sheet thickness range / sheet thickn.: max. 2.7 mm Bending rollers / bending rollers: top: 1 piece , bottom: 2 pieces Driven / driven: 2 sub-rollers/ bottom rollers Upper roller diameter / diameter of top roller: 112 mm Bending speed. / speed bending: 7m /min Minimum bending radius / min. bending radius: 130 mm Weight / weight: 700 kg Connection value / loaded power: 4 kW

sheet width: 1020 mm plate thickness: 2,5 mm daylight opening: 48 mm bending angle max.: 0 - 135 ° total power requirement: von Hand kW weight of the machine ca.: 285 kg dimensions of the machine ca.: 1,35 x 0,82 x 1,14 m Furnishing: - Universally applicable bending machine for plumbing and repair shops - Robust construction in a modern design - Easy adjustment of the upper beam using a foot pedal - Hands are free for the workpiece - Manual bending machine for standard bending tasks - Segmented upper beam for a large number of bending options - Optimal price-performance ratio - Quick and easy bending process using a bow handle - Non-slip rubber coating on the foot pedal for safe working - Easy adjustment of the lower beam to the respective sheet thickness - High upper beam for producing high-edged profiles scope of delivery - Segmented upper cheek - manual backgauge - bending segments 2 ...

Electro-hydraulic. Mandrel bending machine make TRANSFLUID type DB 628 ST SPSMasch. -No: 7507/2/2000 year 2000Technical specifications:Pipe diameter 6 - 30 mmMax. Wall thickness 2 mmSolid material up to 20 mmBending radius min. 10 mmBending angle up to 190 °Bending time at 90 ° 3.0 sec.Mandrel length / pipe pushing length 3000 mmRadius range max. 85 mmBending height 1050 mmfreestanding bending head 850 mm lg.Head for clear width between 2 bends of 300 mm distanceNominal pressure 250 barOperating pressure 200 barDrive power 2.2 kWDimensions L x W x H 3500 x 900 x 1300 mmWeight approx 800 kgWith- PLC control, bending process semi-automatic or manually selectable- Storage of 500 tubes with 20 different positions each- hydraulic drive, right-bending- Triggering optionally via foot or hand switch- Bending direction clockwise, hollow shaft for small radii- Tool reset by hand, hydraulic count ...

Tube bending machine LANG type Ondomat 60 Fabr. No. 2589 Year of construction 1970 Bending capacity max.: 60 x 2 mm Compressive force 20 ton. Counterforce 7.5 tons. Bending angle max. 135 Tool stroke 250 mm Tool width max. 125 mm Outer width of the tool rocker: 90 mm Motor power 18 kW Mains connection 380 volts, 50 Hz - Hydraulic bending process with counter-pressure cylinder for wrinkle-free bending - up to 10 different bending angles in succession via autom. Switching turret - 2-hand control panel - 1 piece bending tool 30 mm, tool width rocker = 78 mm, tool width counter bearing = 50 mm Space requirement L x W x H 2000 x 750 x 1500 mm Weight approx. 2 ton. good condition; used

Face plate bending machine, face plate bending machine, profile bending machine, bending machine, angle bending machine, tube bending machine -Diameter faceplate: 1330 mm -Clamped round blank diameter: 775 mm -for a surcharge: other round blanks can be produced -Geared motor power: 1.5 kW -Speed: 86 rpm -Dimensions: 1200/700/H1210 mm -Weight: 320 kg

combined bending machine-straightening press, profile bending machine, bending machine, flat iron bender, horizontal bending/straightening press, horizontal bending machine -Flat iron bender: hydraulic profile bending machine -Pressure capacity: 140 Ton. -Stroke cylinder: 455 mm -Counter bearing max width: 1250 mm -Support rollers: height adjustable 250 mm -Dimension: 2060/3735/H1620 mm -Weight: 8300kg

sheet width: 2020 mm plate thickness: 2,0 mm daylight opening: 122 mit Segmente mm bending angle max.: 0 - 135 ° work height max.: 930 mm total power requirement: von Hand kW weight of the machine ca.: 1020 kg dimensions of the machine ca.: 2,75 x 0,56 x 1,26 m characteristics - Segmented upper beam for a large number of bending options - Universally applicable bending machine for plumbing and repair shops - High upper beam for producing high-edged profiles - Quick and easy bending process using a bow handle - Easy adjustment of the upper beam for efficient work - The bending angle is set using a scale - Individually removable segments for bending boxes - Large opening width for processing large workpieces - Robust construction in a modern design scope of delivery - Segmented upper cheek - Biegesegm. 25 | 30 | 35 | 40 | 50 | 75 | 100 | 150 | 200 | 300 | 500 | 510 mm The data for this  ...

Reinforcing steel bending machine, shaft bending machine, round steel bending machine -max bending capacity: Ø 32 mm -Drive: 1.3/2.1 kW -Bending angle: Pin-controlled, two-speed, each with pins for left/right to set the angle -Equipment: adjustable counterholder strips, standard bending tool -Dimensions: 750/660/H970 mm -Weight: 356 kg

CNC – controlled profile and tube bending machine for demanding and precise bending work with hollow sections and tubes. With our machines, aluminium – steel / stainless steel – various plastics such as PVC window profiles (depending on the application) can be bent with repeatable accuracy, regardless of the material. Depending on the equipment, our machines can also be used for three-dimensional bending work. Our REPANDUS models can work both horizontally and vertically. The models of the REPANDUS series work with a fixed upper roller and two movable lower rollers – this means that the straight end piece is relatively short compared to machine concepts with fixed lower rollers. The machine body is made of vibration-absorbing cast steel Shaft diameter of upper and lower rollers Ø 70 mm Shafts made of special steel – hardened and ground Bending force 190 kN Maximu ...

CNC – controlled profile and tube bending machine for demanding and precise bending work with hollow sections and tubes. With our machines, aluminium – steel / stainless steel – various plastics such as PVC window profiles (depending on the application) can be bent with repeatable accuracy, regardless of the material. Depending on the equipment, our machines can also be used for three-dimensional bending work. Our REPANDUS models can work both horizontally and vertically. The models of the REPANDUS series work with a fixed upper roller and two movable lower rollers – this means that the straight end piece is relatively short compared to machine concepts with fixed lower rollers. The machine body is made of vibration-absorbing cast steel Shaft diameter of upper and lower rollers Ø 70 mm Shafts made of special steel – hardened and ground Bending force 190 kN Maximu ...

Electro-Hydraulic Bending Machine Fabr. SCHWARZE-WIRTZ type Perfect WE 40 Dmachine -No: 85500 year 1985Max. Bending capacity: 25 x 2 mmPipe diameter min.: 10 mmMax. Bending radius up to center of pipe: 100 mmminute Bending radius up to center of pipe: 25 mmBending angle max.: 180°Bending direction: LeftMax. Bending speed forfeed stepless: 19 rpm.Return constant: 19 rpm.Drive power: 7.5 kWWeight approx.: 700 kgExternal dimensions L x W x H: 2200 x 1100 x 1100 mmWith- Hydraulic slide rail feed- Creeper control- Footswitch- without toolsused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools