ball mill for used for sale

Force measuring device, force measuring device, calibration, force measuring technology, load cell -Manufacturer: Johann Rein -Type: 1Mp -Dimensions: 190/290/H130 mm -Weight: 4.5 kg

Nominal weight of the falling parts: 750 kg Max. number of blows per minute: 105 Kinetic energy: 1900 kg Distance from an axis of the slider up to bed: 750 mm Cylinder diameter: 600 mm Diameter of the plunger: 630 mm Max. headstock travel: 835 mm Dimensions: -Left-to-right: 3940 mm -Front-to-back: 1430 mm Height above floor level: 3260 mm Weight: -With an anvil-block: 25600 kg -Without an anvil-block: 16600 kg

THERMO FORMING MACHINE TFT IMC 5030 (WITH TOOLS) M. No.: 403 Equipment / Additional information: unwinding: Roll recording: easy Max roll diameter: mm 1000 Settlement: automatically Thermoforming machine: Maximum tool dimensions: mm 520x330 Pos. Molding height max .: 15 mm Neg. Molding height max .: 120 mm Sheet width: mm 150/760 Movement Step: mm 50/330 Max HIPS film thickness: 1.8 mm Hub of the sub-table: 150 mm Clamping force: 7500 Kg Inst power top heater: 18.8 Kw Inst power under heater: 14.1 Kw Idle clock speed: per minute 40th power main drive motor: 2.2 Kw Engine power. Film feed: 0.75 Kw Air operating pressure: Kg / cm2 7 Water consumption at 12 °: 1t / 1` approx.30 Air consump. at 7 kg / cm2: 1t / cycle 125 Installed power: Kw 50 9xTool: Article no. // Tool no. // Cavities // Description / Product: 3599 // 457 // 10 // Ven ...

Capacity: 1 200 T, Total stroke: 500 mm, Stroke of main crank shaft: 318 mm, Stroke of mobile die: 215 mm, Stroke/min: 27, Bar diameter: 50-90 (150) mm, Max diameter of peace: 152mm, Max weight of piece: 5 kg, Main motor power: 75 KW, Area of machine : 6400 x 4420 mm, Hight of machine: 3830 mm, Weight: 128.0 T

2000 Ton Sumitomo Hot Forging Press line Year 2006 Stroke 350 mm (13.78") Strokes per min 75 Shut height 850 mm (33.47") SlideAdj. 7 mm (.27") Ram size 1200 mm LR X 1300 mm FB Bed size 1320 mm LR X 1300 mm FB 4 stage transfer system Slide knockout Bottom knockout Scrap System Dual Die Changer Extra Die Shoes Billet Heater and Billet Saw Also Available This line was used by HONDA to make transmission gears, It takes a billet, cuts it to size, heats it to 1300 C then the press hits it 4 times. It can determine good from bad parts, the bad parts get sent to a quench tank, the good parts get sent into a cool down conveyor that you can pick the parts up by hand at the end. The entire system was ran by one operator.

Transnorm Rising falling Incline belt conveyor GF 9820-700-600 RA2087 Technical data: Conveyor length (NL): 9820 mm (6000 mm riser segment + 3820 mm forerun) frame width (NB): 700 mm, 800 mm with motor belt width (GuB): 600 mm Overall height (BH): 80 mm, 430 mm with motor Supporting feet: optionally available Conveying speed (v m/s): 0,42 Drive: SEW gear motor, R27 DRS71M4BE1/MM07/LN Electrical data: 50Hz V380-500, kW 0,75 S1 Drive drum: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Side guide on one side and on both sides Frequency converter for stepless speed change Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany Features: Construction year: 2014 condition: good (used) Conveying length in mm: 9820 Nominal / outside width in mm: 700 Belt width in mm: 600 Driven: YES Engine type: SEW Eu ...

Transnorm Rising falling Incline with arch and forerun belt conveyor GF 12965-700-600 RA2076 Technical data: Conveyor length (NL): 12965 mm (3000 mm forerun + 6865 mm incline + 3100 mm arch) frame width (NB): 700 mm, 800 mm with motor belt width (GuB): 600 mm Overall height (BH): 80 mm, 430 mm with motor Angle: freely adjustable between 0 and 15° Supporting feet: optionally available Conveying speed (v m/s): Frequency converter for stepless speed controll Drive: SEW gear motor, R27 DRE80M4BE1/MM15/LN Electrical data: 50Hz V380-500, kW 1,1 S1 Drive drum: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Side guide on one side and on both sides Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany Features: Construction year: 2014 condition: good (used) Conveying length in mm: 12965 Nominal / outs ...

Forklift battery charger, industrial charger, forklift battery charger, industrial charger -Voltage: 24 volts -Power: 25 A -Connection: 230 volts -Weight: 30 kg

Forklift battery charger, industrial charger, forklift battery charger -24 volts -Power: 63 A -Connection: 220 volts

Forklift battery charger, industrial charger, forklift battery charger, industrial charger, silicon rectifier -Manufacturer: Still, charger Belatron type E 24/90 eco EU -Input voltage: 220 V 50 Hz -Power: 25.2 V/90 A -Dimensions: 550/410/H780 mm -Weight: 94 kg

Formwork nail, formwork nails, concrete nails, head bolts -Manufacturer: Würth, shuttering nail in magazines box with 100 pcs. -Type: SMA 106/10 54mm long -Number: 61x box available -Price: per box -Dimensions cardboard: 120/100/H55 mm -Weight: 0.5 kg/box

Anchor system DW 15 Nut joint plate new, galvanized = 6,90 EUR/piece Prestressing steel DW15,0,85m = 4,20 EUR/piece Prestressing steel DW15,1,00m = 4,80EUR/piece German product manufactured according to DIN with manufacturer's warranty All prices excl. VAT and transport Subject to clearance Company SFS Andreas Becker e. Kfm., Tel. 07305/9562350, Fax. 07305/9562352 , VAT NUMBER: DE279047055 Office/ warehouse address: Birkenstraße 15 89185 Humlangen- Hüttisheim E-Mail: SFsystemst-Online Mobile: 0049 176 70044689 Mr. Becker Registry Court Ulm: HRA722943

H16 Timber beam formwork girder Height 16cm, Width 65mm, Weight 3,3kg/meter The tried-and-tested components for many peeling systems. Formwork girders are basic of many formwork systems and can be used individually. The carefully manufactured beams prove themselves thousands of times a day on many construction sites. The location is our warehouse in 5202 Neumarkt For further information or a viewing, I am always at your disposal. You can reach us at Tel.Nr.: +43 664 1296830 or by e-mail: officeberger-international.at Berger Construction Equipment GmbH

Injection molding machine, clamping force control unit, control unit -Manufacturer: Demag Kunststofftechnik, clamping force control unit -Type: DMS-SKR 79/5 ID no. 064 929 65 RMS -Dimensions: 165/95/H95 mm -Weight: 0.7 kg

Electrode tongs, electrode device, electrode welding device -Electrode clamp: cable without plug -Length: 5m -Weight: 4.5 kg

Servo drive, servo card, output module, CPU card, input processor, power supply, control, converter, controller, servo line former, drive control device -Indramat: AC Servo Line Former from DMT CD320 cycle lathe -Type: NAM 1.2-15 -Item: 246506 K39/96 -Dimension: 325/105/H390 mm -Weight: 21 kg

Ham press Erhard approx. 120 liters capacity, completely in stainless steel, compressed air operated, with intermediate boards and stainless steel brackets, Dimensions LxWxH approx. 107x59x99cm, weight approx. 180kg, good used condition, works perfectly

Forklift battery charger, industrial charger, forklift battery charger, industrial charger, Si rectifier -Manufacturer: Jungheinrich, Timetronic ECO JH charger -Type: D400 G 24/70 B-ETIS -Input voltage: 400V 50-60Hz -Power: 24V/70A -Dimensions: 500/500/H730 mm -Weight: 55 kg

Forklift battery charger, industrial charger, forklift battery charger, industrial charger, Si rectifier -Charger: for forklifts, type GFWEA/W 24/70 -Input voltage: 220V 50Hz -Power: 25.2V/70A -Dimensions: 555/360/H690 mm -Weight: 55 kg

Forklift battery charger, industrial charger, forklift battery charger, industrial charger, Si rectifier -Manufacturer: Oldham, charger type High Power III 36-80 -Input voltage: 220/380V 50Hz -Power: 36 V / 80 A -Dimensions: 555/410/H790 mm -Weight: 66 kg

Effort 2000t moving matrix 280 mm landing pad 570 mm landing slider after closing the matrices 390 mm Number of moves of the ram, stroke / min 25 Electric motor power 160 kW Dimensions, mm: LWH = 856053604850, the level above the floor is 3200. Weight of the car without electricity: 239.8 tons. Weight of the bed: Front part: 82 tons. Rear part: 55t. Weight 270 ton

Forklift bucket, hydraulic forklift bucket, light material bucket, tipping bucket, container tipping device, forklift tines, forklift forks, fork tines -Forklift tines: 2 pieces/1 pair -Length: 1120mm -Cross section: 140 x 60 mm -Recording: see photos -Dimensions each: 1220/140/H620 mm -Total weight: 210 kg

Forklift bucket, hydraulic forklift bucket, light material bucket, tipping bucket, container tipping device, forklift tines, forklift forks, fork tines -Forklift tines: 2 pieces/1 pair -Length: 935mm -Cross section: 140 x 50 mm -Recording: see photos -Dimensions each: 1040/140/H660 mm -Total weight: 156 kg

crane fork, loading fork, load fork, pallet fork, pallet crane fork -Crane fork: with manual balancing -Load capacity: kg -Tine length: 730 mm -manual weight compensation -Fork: adjustable up to 1040 mm -Useful height: adjustable 1170 to 1960 mm -Dimensions: 1060/865/H1130 mm -Own weight: 108 kg

Forklift battery charger, industrial charger, Forklift battery charger, industrial charger, Si rectifier -Manufacturer: DETA, charger type WE 24/64 S -Input voltage: 220 V 50 Hz -Power: 24 V/64 A -Dimensions: 455/380/H810 mm -Weight: 51 kg

Forklift battery charger, industrial charger, Forklift battery charger, industrial charger, Si rectifier -Manufacturer: Still, charger type E 24/50 SL -Input voltage: 220 V 50 Hz -Power: 24 V/50 A -Dimensions: 555/430/H750 mm -Weight: 50 kg

Technical specifications: Rated power, kW: 11,3 Mold area, mm: 475 x 250 Max. film width, mm: 495 Min. film width, mm: 150 Max. feed length, mm: 280 Min. feed length, mm: 50 Max. drawing depth/negative, mm: 100 Number of cycles/min.-max.: 48 Consumption of air/cycle at 6 bar: 100 Nl (net-pressurized air) Heat energy to be dissipated: with top heating ca. 10 260 KJ/h with top and bottom heating ca.: 17 715 KJ/h Special equipment: Hollow floor facility available Control cabinet: included

Forklift battery charger, industrial charger, Forklift battery charger, industrial charger, Si rectifier -Charger for forklifts: Miditron Type D 400G 48/100 PWF-PMT -Input voltage: 400 V 50 Hz -Power: 48 V/100 A -Dimensions: 555/530/H690 mm -Weight: 112 kg

Transnorm Rising falling Incline with arch and forerun belt conveyor GF 7600-700-600 RA2101 Technical data: Conveyor length (NL): 7600 mm (800 mm forerun + 6000 mm incline + 800 mm arch) frame width (NB): 700 mm, 800 mm with motor belt width (GuB): 600 mm Overall height (BH): 80 mm, 430 mm with motor Angle: freely adjustable between 0 and 15° Supporting feet: optionally available Conveying speed (v m/s): Frequency converter for stepless speed controll Drive: SEW gear motor, R27 DT80N4/BMG/TH Electrical data: 50Hz V380-500, kW 0,75 S1 Drive drum: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Side guide on one side and on both sides Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany Features: Construction year: 2014 condition: good (used) Conveying length in mm: 7600 Nominal / outside width ...

Transnorm Rising falling Incline with forerun belt conveyor GF 4780+800-700-600 RA2103 Technical data: Conveyor length (NL): 5580 mm (800 mm forerun + 4780 mm incline ) frame width (NB): 700 mm, 800 mm with motor belt width (GuB): 600 mm Overall height (BH): 80 mm, 430 mm with motor Supporting feet: optionally available Conveying speed (v m/s): Frequency converter for stepless speed controll Drive: SEW gear motor Electrical data: 50Hz V380-500, kW 0,55 S1 Drive drum: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Side guide on one side and on both sides Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany Features: Construction year: 2014 condition: good (used) Conveying length in mm: 5580 Nominal / outside width in mm: 700 Belt width in mm: 600 Driven: YES Engine type: SEW Eurodrive Zentrala ...

Forklift battery charger, industrial charger, Forklift battery charger, industrial charger, Si rectifier -Manufacturer: Hagen Battery, Charger Belatron Type E220 G24/50 B-FB -Input voltage: 220 V 50 Hz -Power: 25.2 V/50 A -Dimensions: 540/330/H420 mm -Weight: 40 kg

Forklift battery charger, industrial charger, Forklift battery charger, industrial charger, Si rectifier -Manufacturer: Jungheinrich, charger type DLW 12/20 SN -Input voltage: 220 V 50 Hz -Power: 12 V/20 A -Dimensions: 410/200/H340 mm -Weight: 12 kg

lifting mast, stacker mast, forklift mast, lifting frame, rear loader -Manufacturer: Clark, forklift mast from forklift type C500-Y80 -Load capacity: approx. 4000 kg -Lifting height: mm -Recording/Dimensions: see photos / technical drawing -Dimensions: 1245/420/H2350 mm -Weight: 1120 kg

Fork carrier, forklift blade, pallet fork, forklift fork, for wheel loader, forklift, telehandler, stacker, tractor -Fork carriage: without forks -Load capacity: 1500 kg -Beam width: 2500 mm -Forks: available in a wide selection -Total dimensions: 2500/130/H400 mm -Weight: 370 kg

Forklift battery charger, industrial charger, forklift battery charger, industrial charger, Si rectifier -Charger: for forklifts, type D 24/200 MULTI WF200 -Input voltage: 400 V 50 Hz -Power: 24 V/200 A -Dimensions: 555/520/H890 mm -Weight: 119 kg

Forklift bucket, hydraulic forklift bucket, light material bucket, tipping bucket, container tipper, forklift tines, forklift forks, fork tines -Forklift tines: 2 pieces/1 pair -Length: 1140 mm -Cross-section: 130 x 55 mm -Recording: see photos -Transport dimensions: 1330/690/H135 mm -Total weight: 167 kg

Forklift bucket, hydraulic forklift bucket, light material bucket, tipping bucket, container tipper, forklift tines, forklift forks, fork tines -Forklift tines: 2 pieces/1 pair -Length: 1400 mm -Cross-section: 125 x 45 mm -Recording: see photos -Transport dimensions: 1520/560/H125 mm -Total weight: 148 kg

Transport carriage IVG, built in 2020, craneable, load capacity 3to, unused. Transport carriage IVG, YOC 2020, unused, load capacity 3to, for the transport of turbine shafts or other objects, craneable, with reinforced attachment points for slipping or for safe transport with a forklift. Multiple presents. Dimensions approx. 2,400x750x500mm Dimensions approx. 2,400x750x500mm Dimensions approx. 2,000x750x500mm

Forklift bucket, hydraulic forklift bucket, light material bucket, tipping bucket, container tipper, forklift tines, forklift forks, fork tines -Forklift tines: 2 pieces/1 pair -Length: 1800 mm -Cross-section: 200 x 60 mm -Recording: see photos -Transport dimensions: 2060/1080/H200 mm -Total weight: 487 kg

Lifting mast, stacker mast, forklift mast, lifting frame, rear forklift -Manufacturer: Baumann, forklift mast from sideloader type AS 60/18/15 -Load capacity: approx. 6000 kg -Lifting height: mm -Recording/Dimensions: see photos / technical drawing -Transport dimensions: 3200/1620/H750 mm -Weight: 2100 kg

Lifting mast, forklift mast, forklift mast, lifting frame, rear forklift, triplex mast -Manufacturer: Linde, Triplex mast for electric forklift type E20 -Load capacity: 2000 kg -Dimensions: see photos / technical drawing -Dimensions: 2530/1150/H415 mm -Weight: 1070 kg

Lifting mast, forklift mast, forklift mast, lifting frame, rear forklift, triplex mast -Manufacturer: Linde, Triplex mast for electric forklift type E20 -Load capacity: kg -Dimensions: see photos / technical drawing -Dimensions: 2230/1150/H375 mm -Weight: 920 kg

Force gauge, force measuring device, calibration, force measurement technology, scale, crane scale, hanging scale -Manufacturer: dynafor , tensile force measuring device crane scale -Measuring range: up to 20 t -Dimensions box: 490/160/H160 mm -Total weight: 12 kg

Universal formwork Paschal Raster Universal formwork for foundations, walls, columns, beams, shafts, curves (polygons), landscaping construction, prefabricated elements. Versatile and flexible for use as manual and large-area formwork. Thanks to the modular principle, systemic formwork is very possible, even with complicated floor plans. The flat steel frames guarantee the robustness and durability of the formwork. Compatible with all PASCHAL systems. Connecting bolts as a universal fastener for all elements and accessories.

Rheon Model KN100 Cornucopia Encruster. Maximum speed approx. 60 pieces per minute, depending on the product. Weight capacity from 10 - 90 grams. (2) 11.5" x 8" x 7" stainless steel feed hoppers, each with (2) 2.5" diameter feed screws. Approx. 5 inches wide discharge conveyor. Digital touch controls. Compact forming, filling and portioning machine Connection 400V, 16A-CEE plug Used machine from bakery

Forklift bucket, hydraulic forklift bucket, light material bucket, tipping bucket, container tipper, forklift tines, forklift forks, fork tines -Forklift tines: 2 pieces/1 pair -Length: 1195 mm -Cross-section: 100 x 45 mm -Recording: see photos -Transport dimensions: 1370/610/H100 mm -Total weight: 112 kg

Specifications: - Total width approx. 800 mm - Work surface length / web length approx. 120 mm - Working surface depth / web depth approx. 120 mm - Total depth approx. 100 mm - Round horn approx. 340 mm - Square horn approx. 340 mm - Anvil height with substructure approx. 820 mm - Anvil weight approx. 65 kg - Substructure approx. W 420 x D 420 x H 300 mm - Substructure mounting hole 85 mm - Weight of substructure approx. 35 kg

Weld edge former, weld edge former, weld preparation, weld edge forming machine, edge milling device, edge milling machine, mobile milling machine -Manufacturer: BDS, Weld edge former/edge milling machine with accessories -Type: SKF 20 -Power: 1.1 kW -Accessories: see photos -Box dimensions: 460/355/H355 mm -Total weight: 33.2 kg

Weld edge former, weld edge former, weld preparation, weld edge forming machine, edge milling device, edge milling machine, mobile milling machine -Manufacturer: BDS, Weld edge former/edge milling machine -Type: SKF 20 -Power: 1.1 kW -Accessories: see photos -Box dimensions: 460/355/H355 mm -Total weight: 29.4 kg

Crane fork, loading fork, load fork, pallet fork, pallet crane fork, lifting equipment, roller lifter -Crane fork: with adjustable weight compensation -Type: Hoist 630x475 -Load capacity: 250 kg -Tin length: 490 mm -Usable height: 610 mm -Dimensions: 635/520/H795 mm -Weight: 21 kg