used Assembly stations for sale

Rail system with vacuum lifters B II and integrated chain hoist: Single girder rail system of suitable to below vacuum lifting device. All castors are fitted with lateral guide rollers and ball bearings. Transverse and longitudinal drive manually by pulling or pushing on the load Length approx. 6 m Span 5 m Crane beam length approx. 9 m Suspension distance approx. 4 m Lower edge of bridge girder approx. 3 m The longitudinal rails are suspended from the construction side rolled profile carrier with 6 suspensions and consoles attached to the wall side of the additional 2 PCs.. Vacuum lifter B II Load 200 kg suitable for vertical transport of flat float glass plates. Vacuum generation is pneumatically by means of an ejector. A tailings facility for quick raising of the glass plate is installed. Sicherheitendschalter, non-return valve and vacuum gauges Elect ...

Dimensions (L,W): 3000 x 1.600 mmWeight: , kgtiltable yes/no: nein 1 pc. Bäuerle glazing stand---------------------------------Length 3000mmHeight 1,600mmRoll width 200 mmPneumatic high/low via foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

0: 3200 mmWorking height: 1950 mm0: 500 mmFederhenn glazing and control pressfor glazing, sealing and final inspection.Clamping width: min.max: 350/3200 mmPress beam height: 1950 mmDimensions L/W/H: 4000 x 950 x 2300/2900 mmWeight: approx. 510 kgTwo press beams that can be folded down and moved pneumaticallySimultaneous, synchronous folding and moving of the press beams,thus minimum time required when opening and closing the pressPress beam guided above and below via racks, therebyabsolute parallel run when pressingpneumatic lifting device from 305-805 mm with 2 lifting cylindersLower roller track B=150 mm long as a set-up areaProtective rollers on both sides(Technical description according to the manufacturer - without guarantee!)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Manual hand unit: Nein J/NAutomatic for single pieces: Ja J/NAutomatic for frames: Nein J/NClip set 351 on the loose item------------------------------------Manufacturer description:- Base frame in stable welded construction- Clip container as tipping conveyor with separation and feeding the clips- Screwdriver with tipping conveyor for the screws to be separated, feed screwdriver pneumatic with depth adjustment- Conveyor belt length approx. 4,000 mm as NC axis- Contact and clamping cylinder- Electro-pneumatic control via PLC It can programs with different Initial and distance dimensions can be entered- Workflow automatically in flow--------------------------------------Technical specifications:- Screw height 50-120 mm- Profile length 350-3,500 mm- Table height approx. 950 mm--------------------------------------Total price of the machine ex works: on request!Freight costs within Ger ...

0: ja, freitstehend Working width: 3000 mm0: ja RUCHSER sash assembly table RU-BM-3000---------------------------------------The Ruchser sash fitting center enables efficient production based on economic aspects. Well thought-out down to the last detail, the system offers maximum ease of use.Important advantages for you:Modular system, the sash assembly table is put together according to your wishes and requirementsEasy to use even for inexperienced workersEquipment demonstration machine, alternative / optional equipment on request!Pos. 1.0: Article no. : 0610000RU-BM-3000, sash assembly table, for sashes up to max. 2500 mm in heightwith RU-SH, special screwdriver length 3000 mm, width 1400 mm, inclination of the work platform manually adjustable.Holder for fitting scissors or fitting punch.10 pieces swiveling commuters for hanging theWing, completely pneumatically foldable forunhindered ...

Dimensions (L,W): 1400 x 1750 mmWeight: , kgtiltable yes/no: ja RUCHSER assembly tilting table RU-MKS 1,4---------------------------------------Universally applicable work table e.g. for frame assembly, roller shutter box assembly, bars, sash fittings, glazingEquipment demonstration machine, alternative / optional equipment on request!Pos. 1.0: Article no .: 8820000RU-MKS-1,4 assembly tilting tableBasic dimensions 1400 x 1750 mm, extended 3400 x 2500 mmSupport surface with 3 support bars, 2 of which are adjustable,one permanently mounted on the upper extension,covered with felt. Support surface with width andHeight / depth pull-out. Pneumatic tilting device,Payload 130 kg. Actuation via foot valve.Roller conveyor can be folded down manually and pulled out to the sidefrom 1400-2500 mm, roll length 140 mmclosed. Roller conveyor height in verticalTable position adjustable from 300-380 mm,Ho ...

0: 2750 mmWorking height: 2500 mm0: 300-1000 mmRUCHSER glazing and sealing table RU-SW3-90° year of manufacture 2022-----------------------------------------------------Vertical work table with lifting device and turning device. EspeciallySuitable for glazing and sealing wooden windows on both sides.Furnishing:System part covered with feltInfinitely variable pneumatic lifting device,Stroke of 300 mm - 1000 mm, based on roller conveyor heightTurning device for sealing on both sides, with roller conveyor 150 mmroll length2 pneumatic tensioners for clamping the window to the turning deviceVersion with special turning device for pushing through the on theRoller conveyor set up window with applied (closed)turning deviceEquipment demonstration machine, alternative/optional equipment on request!Pos. 1.0: Item no.: 1000000RU-SW3-90° vertical work table forWooden window with turning device forG ...

FENSTER-UNIVERSAL-DREH-KIPPTISCH RUCHSER-Universal for wing and frame motions. Rotary tipping table with pneumatic tilting device, work platform with 4 loading holes. Height 900 mm-1050 mm adjustable. Lifting device 400 mm 6 storage boxes Fahing facility Used machine without warranty or warranty. Loveling from the Hamburg location unloaded.

SPECIFICATIONS: Machining center for final processing and assembly of fittings on windows and doors Dimensions workbench mm: 2,800 x 1,250 Three-spindle drilling unit for grip holes Pneumatic system for reading and cutting window handles "Cremonese" Tilting workbench Complete with pneumatic screwdriver

Window assembly station, factory WORKER Width about 3000 mm outdated!