used Edge gluing machines for sale

Description: - Hot use of pre-glued strips for finishing linear and shaped panels - Main motor 3.95 kW - Accidental burn protection - Height adjustable edge guide - Rubber pre-tape roller - Double flat scrapers on both sides of the panel - Edge header - Edge thickness 0.8 - 2 mm - Min/Max panel thickness 12/43 mm - Working speed: 7 m/min The item that is delivered is NOT the one shown in the pictures, but an equal oneApprox. Onsite Dimension. (l x w x h): 2,000 x 670 x 1,260 mm, weight approx.: 470 kg

Description: - Hot gluing of pre-glued strips for finishing linear and shaped panels - Main motor 3.59 Kw -Protection against accidental burns - Height adjustable edge guide - Pre-tape rubber roller - Double flat scrapers on both sides of the panel - Edge header - Edge thickness 0.4 - 2 mm - Min/max panel thickness 12/43 mm - Working speed: 7 m/minApprox. Onsite Dimension. (l x w x h): 2,000 x 670 x 1,260 mm, weight approx.: 485 kg

single-sided edge banding machine with pull-out workpiece support, end trimming unit and combi-unit. Power consumption: 400 V / 50 Hz / 3 pH / 7 kW Compressed air supply: 6 bar Dimensions: approx. 4,000 x 1.300 (1,780) x 1520 mm Edition extendable to 800 mm Working height: 820 mm Roller plate ø 700 mm

Key data: 1 mm

Equipment and technical data: Edge banding machine for pre-coated edge material High-performance heat gun Roll capping electromagnetic Edge milling machine Sytem Hebrock End capping: Cross-cut module for flush cutting the front Edge protrusion Feed: 3-roller system Boom on both sides Add-on trolley, mobile max. edge thickness approx. 1 mm max. workpiece height approx. 50 mm min. workpiece length approx. 170 mm min. workpiece width approx. 50 mm Feed rate approx. 4 m/min. Ready for use: approx. 1 minute Dimensions 1730 x 690 x1240 mm Weight approx. 115 kg Sale takes place in the ACTUAL state Technical information, description of condition, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale In the case of used machines, any warranty is excluded, it is valid to buy as well  ...

Description: Cross-cut saw unit : 1 motor / Flush trimming / Raidus trimming / Flat scraper blade Buffing unit Glue thickness max : 8 mm Thickness of roll material max : 3 mm Units synchronised : pneumatic Gluing height max : 50 mm Workpiece length min : 300 mm - Workpiece width min : 90 mm Feed rate max : 10 m/min Strip magazine : Yes Total connection : 12.6 kW ' Some of the technical data is taken from the manufacturer's brochure. Actual values may differ' Machine length : 4,300 mm Milling motors have slight bearing noises - tools must be changed - slight leakage at the DL cylinders. PRICED IN FUNCTIONALLY TESTED CONDITION , SOLD WITHOUT WARRANTY! Data is taken from the manufacturer's brochure/documents and may differ from the actual values. ATTENTION: It is expressly pointed out that this lot only corresponds to the scope of the lot description. , If the photo shows obje ...

Hebrock AKV3003DK-F edge banding machine with joints and two scraper blades. Edge thickness roll approx. 0.4 - 2mm Banding up to 8mm Workpiece height approx. 8 - 45mm Feed rate approx. 10m/min Noise protection hood Extendable workpiece support Suction connection 80 +140mm Aggregates: Manual overpressure adjustment with SIKO counter Infeed ruler manual adjustment with SIKO counter Edge thickness manual adjustment with SIKO counter Grooving mills with slide mills Gluing part with automatic edge retraction for rolls up to 3mm, switchable for synchronization and counter-rotation Pressure zone with 4 rollers Cross-cut saw Integrated collection container for edge pieces Combination milling unit, R2 with pneumatic adjustment between thin and thick edge Radius scraper R2, pneumatically retractable Glue joint scraper blade can be pneumatically inserted ...

Brand: Hebrock Model: AKV83 Year of construction: 1992 Specifications: Edge thickness 0,4 - 5,0mm Roll ø750 mm Plate thickness max. 10-60 mm Workpiece length: min. 170 mm Connection: 230V, 40Hz Relay Control 1.Hot air (Phön) 3 KW, heat time: 1 min. 1. Caper knife - front & rear same product capping 6. Flat milling top & bottom Feed 4 m/min. Air pressure 7 - 8 bar Machine dimensions: LxHxW 1.750 800 1.250 mm (incl. plate) Machine weight: 95 KG

Hebrock Euro 2000 Edges up to 5mm striped fabric Granule Hot Melt Glue Basin heated inlet ruler Roller capping pneumatic 0.2 - 3 mm Saw capping rigid 90° - combi milling unit flush + radius Chassis Dimensions 2800 x 1400 x 1400 mm Weight approx. 550 kg Machine is currently still in use ex location NET € 3.200,00

Equipment: -Chassis - Quick-heating glue container - Support plate for rolls - Roll capping - Cross-cut saw - Flush milling Radius/Straight/Chamfer - Suction nozzle Ø 100 mm Specifications: Power ratings: 400 V, 50 Hz, 13.3 A, 7 kW max. edge thickness 5 mm max. workpiece height 40 mm min. workpiece length 300 mm Feed speed 11 m/min Ready for use in approx. 4.5 min Work table height 900 mm Dimensions: 3,300 x 1,400 x 1,300 mm Weight approx. 550 kg All information is subject to change of the actual equipment

Code: 0806 Brand: HIRZT - ITALY Model: B 300 - CE Standard Automatic edge bander for pre-glued edges in strips or rolls: melamine, plastic laminates, veneer, etc . up to 3 mm thickness - CE Standard Composition: Motor V. 220 single-phase Pneumatic end cutting unit (shear) front and rear Blower with air filter - Power 440 W Trimming copying unit with adjustment from the outside - Motors 220 x 2 W - Trimmer speed rpm 10000 End cutting finishing unit with foot control N° 20 rollers inclined on the plane Feed motor 13 wheels V.200 single-phase - Speed 4,7 mt/min Max edge thickness mm 3 Panel thickness min/max 10/50 mm Min panel dimensions mm 70 x 140 Total absorption Kw 3,8 Digital thermometer 10-350 degrees Extensible front support Overall dimensions mm 1800 x 700 x 1300 h Weight kg 250

well-kept HolzHer 1422 K Banding thickness up to 20mm Gluing, capping, flush or radius milling Total length approx. 3450mm

•Compact design - edge thickness 0.4 - 6 mm •Control panel with selector switch for adjusting the units •Pre-milling unit for attachment in front of the gluing part •Fully automatic edge magazine for rolls and strips •Adhesive application station cartridges + PU gluing •Workpiece height 6-60 mm •Printing unit pneumatic •Cross-cut unit 1918 pneumatically for rolls and strips up to max. 6 mm edge thickness •with pneumatic changeover from 0-10° inclined of the cross-cut saws • Milling unit flush milling 6 mm, radius milling 3 mm, bevel milling - 15° •Scraper unit for chamfers and radii with 2 scraper blade carriers •pneumatic engagement and disengagement •Surface Scraper Unit - Finish •Machine WORKSHOP overhauled in TOP CONDITION from stock Lieboch

Wood Her Auriga 1308 FÜ + PU compact design - edge thickness 0.4 - 8 mm PLC screen control Edge Control PPC 221 color screen Pre-milling unit for joining in front of the gluing part Edge magazine fully automatic for rolls and strip goods Glue Application Station GLU JET Cartridges + PU Gluing - Multisystem + Glue application using nozzle technology Workpiece height 6-65 mm Auto. Glue height adjustment Printing unit 1912-3 pneumatic Cross-cut unit 1918 pneumatic for rolls and strip goods up to 8 mm edge thickness with pneumatic adjustment from 0-10° inclination of the cross-cut saws Milling unit 1827 MOT 4, flush milling 8 mm, radius milling - bevel milling - 15° 1827 MOT NC axes via control panel Mould milling unit 1832 pneum. Rounding of corners up to edge thickness 3mm in the run Drawing blade unit 1929 for chamfers and radii with 2 drawing blade carriers via control p ...

Edge banding machine wood Her Express 1437 Banding height max. 51 mm Edge thickness 0.3 - 13 mm Swivelling control panel Hot melt adhesive application - cartridge system Car. Edge magazine Full car. Edge feeding for roll and strip goods Printed work Cross-cut unit swivelling 0° - 15° Bevel radius milling Drawing blade unit Buffing unit immersion-controlled Soundproofing booth Machine length approx. 4500 mm Machine in working order From the carpentry site

Wood Her Sprint 1312 FÜ + PU heavy design - edge thickness 0.4 - 8 mm PLC screen control Pre-milling unit for joining in front of the glued part Fully automatic edge magazine for roll and strip goods Glue application station cartridges + PU gluing car. Tactile nozzle Workpiece height 6-55 mm Cross-cut unit for rolls and strips up to 8 mm edge thickness with changeover of 0-10° inclination of the cross-cut saws Milling unit, flush milling 8 mm, radius milling - chamfer milling - 15° MOT Pulling blade unit for chamfers and radii with 2 pulling blade carriers pneum. pneumatic engagement and disengagement Surface Drawing Blade Unit - Finish Spraying device - PU Machine in TOP CONDITION

Holz Her Sprint 1321 FÜ + PU heavy-duty version - edge thickness 0.4 - 15 mm PLC Screen Control Edgecontrol Motorized, positioning-controlled bridge height adjustment Pre-milling unit for fastening upstream of the gluing station Fully automatic edge magazine for rolls and strips Glue application station cartridges + PU gluing Car. Glue height adjustment / tactile nozzle Printed plant 1913 pneum. Cross-cut unit for rolls and strips 1918 - 15 mm with pneumatic changeover of 0-10° incline of the cross-cut saws Multifunctional milling unit with mot. Adjustment: Flush milling - 15 mm, radii and bevel milling -15° Frommilling unit - corner rounds 1833 Scraper unit for chamfers and radii 1929 pneum. pneumatic indentation and disengagement Surface Scraper Unit - Finish pneum. Buffing unit for replastering and edge polishing with 2 textile discs HIGH-END spraying device Compl ...

Wood Her Sprint 1411K Edge banding machine complete in basic configuration with pneumatic printing unit Extendable workpiece support groping nozzle Blowing nozzle Chip collection box pneumatic adjustment of the milling machine and scraper blade Surface scraper blade Special cylinders for edge transport G&-5061-O0945

Wood Her Tria 120 Full car. Edge magazine Full car. Roller magazine - cross-cut shears Banding - 20 mm CARTRIDGE PU GLUING STATION Flush caps Flush - Chamfer - Radius Milling/Digital - 20 mm Soundproof booth from retirement Machine is WORKSHOP OVERHAULED

Wood Her UNO 1304 FÜ + PU Edge thickness 0.4 - 6 mm Control panel with selector switches for adjusting the units Pre-milling unit for attachment in front of the gluing part Fully automatic edge magazine for rolls and strips Glue Application Station: Cartridges + PU Gluing Workpiece height 6-55 mm Printing unit pneumatic Cross-cut unit 1918 for rolls and strips up to 8 mm edge thickness with pneumatic changeover of 0-10° incline of the cross-cut saws Milling unit flush milling 6 mm, radius milling - bevel milling - 15° Scraper unit for chamfers and radii with 2 scraper blade carriers pneumatic indentation and disengagement Surface Scraper Unit - Finish Machine is WORKSHOP OVERHAULED in TOP CONDITION from a craftsman's workshop

Description: Workpiece thickness 6 - 50 mm Min. length 60 mm Maximum width 180 mmApprox. Onsite Dimension. (l x w x h): 4,000 x 1,200 x 1,400 mm, weight approx.: 970 kg

Description: Edge height max 51 mm Minimum workpiece length mm: 180 Electro-motor height adjustment: yes  ,edge thickness: max 13 mm, workpiece width min.: 60 mm, feed: 11 m/min, gluing unit: YES, snipping unit: YES, rough trimming unit: YES, fine trimming unit: YES, profile scraping unit: YES, edge buffing unit: YES, Approx. Onsite Dimension. (l x w x h): 0 x 0 x 0 mm, weight approx.: 0 x 0 x 0 kg

Edge banding Holz-Her Type: 1417 Sprint Year of construction: 1999 Banding thickness max. 8 mm Workpiece thickness = banding height 6 – 45 mm Workpiece width min. 60 mm Workpiece length min. 180 mm Workpiece protrusion via the transport chain on the assembly side 30 mm Feed speed 11 m/min. Feed motor 1.5 kW Swivel control panel Machinery: Pre-milling unit 1961 Edge feeding 1901 - fully automatic edge feeding of roll goods and stiff goods Glue application station 1906 or 1910 cartridge system Printed in 1913 Cross-cut unit 1918 – 2 cross-cut saw motors guided diagonally on round bars Milling unit 1942 – flush/radius/chamfering station Milling unit 1942 M – flush/radius/chamfering station Scraper unit 1929 - for radii up to 3 mm Form milling unit 1983 – 1 motor 0.6 kW 18000 rpm, copy corners up to 3 mm edge thickness Surface scraper unit 1964 – for  ...

Description: Workpiece: Workpiece thickness: min. 6 mm, max. 45 mm Workpiece width: min. 60 mm Workpiece length: min. 180 mm Maximum edge thickness: 3 mm Drive: Feed rate: 10 m/min Power: 1.5 kW Control voltage: 24 VDC Compressed Air: Operating pressure: 6 Bar Limit pressure: 8 Bar Connection: Quick coupling, nominal width 7, hose inner diameter at least 12 mm. Air consumption: 5 L/min Machine comes without RETURN ,serial number: 98/1-003, Approx. Onsite Dimension. (l x w x h): 5,335 x 1,670 x 1,415 mm, weight approx.: 3,000 kg

I am selling an edge banding machine Holz-Her Sprint 1310, built in 2004. Configuration: Edge banding Cartridge glue Cross-cut saws Swivelling radius milling machines Radius pulling blade Polishing brushes Very good condition, fully operational.

Equipment: - PLC control - Edge magazine - Glue application system "Cartridge" -Printed work - Cross-cutting unit - Milling unit, for flush/chamfer/radius - Shape milling unit - Radius scraper blade Specifications: - Length: 4,445 mm - Width: 1,500 mm Working Dimensions: - Workpiece thickness: 6-45 mm - Edge thickness: 0.4-8 mm - Workpiece width: min 60 mm - Workpiece length: min. 180 mm - Feed speed: 8/16 m/min without corner copying - Extraction connection: 2 x Ø 70 mm Static vacuum 1650 Pa Min. air velocity 20 m/sec - Compressed air connection 6 bar technical data subject to actual equipment!

Description: Joiningagreat 2 x 2kW /gluing cartridge system/capping/milling station radius chamfering 0-15°/radius drawing/ separating/ detergent spraying unit copy milling unit/ surface scraper/ fettling station edge thickness max.: approx. 0,4 - 8 mm [mm] workpiece height 6 - 50 [mm] feed speed approx.: 8 [m/min] / elect. connection: 400 V, 3Ph, 50 Hz PRICING IN FUNCTIONALLY TESTED CONDITION - SOLD WITHOUT WARRANTY! Data is taken from the manufacturer's brochure / documents and may differ from actual values. ATTENTION: it is expressly pointed out that this lot corresponds only to the scope of the lot description. If there are any objects on the photo that are not explicitly mentioned in the lot description, they are not part of the sale. Of course, this also applies to tools, additional equipment, accessories, software, operating equipment, etc. (in relation to the photo and lot d ...

Description: • Edgebander • Serial number 147/9-909 (1999) • Edge thickness in strips up to 13 mm • Edge thickness in roll from 0.30 mm up to 5 mm • Worpiece thickness from 6 mm up to 45 mm • Minimum workpiece lenght 180 mm • Minimum workpiece width 60 mm • Feed speed 11 m/min • Feed motor 1.50 KW • PLC control system • HOLZ-HER 1902 edge feeder for roll, edge magazine for one edge coil • HOLZ-HER 1906 cartridge glue system • HOLZ-HER 1913 pressure group with (1+2) rollers • HOLZ-HER 1918 end trimming unit, 2 x motor 0.35 KW-9000 rpm, tilting up to 10° • HOLZ-HER 1942 M fine trimming unit, 2 x motor 0.60 KW-9000 rpm, tilting up to 15° • HOLZ-HER 1929 profile scraping unit • HOLZ-HER 1940 edge buffing unit, 2 x motor 0.12 KW-1640 rpmApprox. Onsite Dimension. (l x w x h): 4,200 x 1,200 x 1,750 mm, weight approx.: 2,000 kg

Edge banding machine, manufacturer Holzher, type Streamer 1057XL C, year of manufacture 2022, max. working length approx. 4,000 mm, with integrated scraper unit, radius scraper ZK 301, surface scraper FK 701, buffing unit 1940, spraying device front and rear TR201, extendable workpiece support 600 mm, extraction line to the first slider, operating hours 15 (read)

Description: • Edgebander • Edge thickness from 0.40 mm up to 25 mm • Worpiece thickness from 6 mm up to 60 mm • Adjustable feed speed: 8 m/min - 20 m/min • Control • Joint trimming unit, 2 x motor 2 KW-12000 rpm • Edge feeder for strips and roll, edge magazine for one edge coil • HOLZ-HER 1906 cartridge glue system • Pressure group with (1+2) rollers • End trimming unit with 2 motors • HOLZ-HER 1823 fine trimming unit, 2 x motor 0.60 KW-12000 rpm • Profile scraping unit • HOLZ-HER 1983 profile trimming unit • Edge buffing unit • Milling group, motor 3.80 KW-12000 rpm • Sanding belt unitApprox. Onsite Dimension. (l x w x h): 7,550 x 1,150 x 1,900 mm, weight approx.: 4,000 kg

Description: • Edgebander, edge banding machine • Edge thickness from 0.40 mm up to 25 mm • Worpiece thickness from 6 mm up to 60 mm • Minimum workpiece lenght 140 mm • Minimum workpiece width 60 mm • Adjustable feed speed from 8 m/min up to 20 m/min • Feed motor 4.40 KW • HOLZ-HER 1961 joint trimming unit, 2 x motor 2 KW-12000 rpm • Edge feeder for 1 edge coil, edge magazine for 1 edge coil • HOLZ-HER 1907 cartridge glue system with pot for granulated hot melt adhesive • HOLZ-HER 1926 K pressure group with (1+2) rollers • HOLZ-HER 1819 snipping unit, 2 x motor 0.45 KW-12000 rpm • HOLZ-HER 1962 rough trimming unit, 2 x motor 2 KW-12000 rpm • HOLZ-HER 1934 lower profile trimming unit, 2 x motor 0.45 KW-12000 • HOLZ-HER 1933 upper profile trimming unit, 2 x motor 0.45 KW-12000 • HOLZ-HER 1927 profile scraping unit • HOLZ-HER 1964 flat scraping unit • HOL ...

Description: • Edgebander • Serial number 14589/9-810 • Total installed power approx. 9 KW • Edge thickness from 0.40 mm up to 8 mm • Worpiece thickness from 6 mm up to 45 mm • Minimum workpiece lenght 180 mm • Minimum workpiece width 60 mm • Feed speed 11 m/min • Feed motor 0.75 KW • Control • HOLZ-HER 1902 edge feeder for roll, edge magazine for one edge coil • HOLZ-HER 1906 cartridge glue system • HOLZ-HER 1913 pressure group with (1+2) rollers • HOLZ-HER 1976K end trimming unit, 2 x motor 0.22 KW-9000 rpm • HOLZ-HER 1942M fine trimming unit, 2 x motor 0.60 KW-9000 rpmApprox. Onsite Dimension. (l x w x h): 4,000 x 1,450 x 1,250 mm, weight approx.: 1,000 kg

- CE certification - Complete, original wood Her machine documents and operating instructions - Weight: 720 kg (basic machine), approx. 860 kg (machine with aggregates) Assembly: • Control panel (1888) SK 180 • Fully automatic edge feeding (1903) - Edge thickness striped goods 0.3 - 8 mm - Edge thickness rolled goods 0.3 - 3 mm - max edge height 51 mm • Adhesive application station (1906 M) - with hot melt adhesive cartridge - via sword nozzle with electro-pneumatic control - Temperature selector - Heating time approx. 5 min - Temperature approx. 190 - 240 degrees Celsius - Workpiece thickness 6 - 45 mm • Printing Unit (1912) • Cross-cut unit (1918) • Combino milling unit (1942 M) - for flushing, chamfering and radius milling • Pull blade unit (1929) - Edge thickness max. 3mm • Sandbar unit (1940) • 2 x suction connections 70 mm each • Compre ...

Key data: 20 mm, 60 mm, 8365 mm

I am selling a fully equipped edge banding machine HOMAG EDGETEQ S-500 KAL370 Ambition 2484, built in 2019: Configuration: Input stop servo-motor adjustable Manually adjustable joint milling Edge banding with preheating tanks 2 pcs. Material pressure zone can be adjusted by servo motor Pneumatically adjustable cross-cut saws Heavy milling top + bottom pneumatically adjustable Round unit 4-motor servo motor adjustable R2 / second set R1 included Swivel groove saw unit Radius scraper blade Multiradius servo motor adjustable Scraper blade surface can be pneumatically adjusted Polishing brushes Separator injection at the front Clean injection at the rear Working height adjustable by servo motor Material height 8-60mm Edge material thickness 0.4-12 (20)mm Feed speed 16 to 25m/min. Overall length including feed plate 8365mm Mileage status 833,000 meters. Input appar ...

Interchangeable heads used, good condition 16 pcs. Interchangeable heads FK 11/13 devices, exchangeable at the top below. 1 Quickmelt incl. evaluation device level.

Description: Min. edge thickness 0.3 mm Max. edge thickness 3 mm , Max. forward feed speed 25 m/min Pressure with rubber belt Panel support guides , with positioning by NC , Infeed panel alignment system , NO. PANEL SIZING / MILLING UNITS , Unit : pre-milling unit automatic timed intervention motor power : 3 KW r.p.m. : 9000 RPM Lamps to preheat the side of the panel , Edge coil magazine , glue pot for EVA hot melt glue premelter for EVA hot melt glue , Roller set to press the edge no. pressure roller 7 with positioning by NC , No. Edge Processing Units 7 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 motor power : 0.8 KW r.p.m. : 12000 RPM NO. EDGE PROCESSING UNITS 2 Processing Unit : top and bottom rough trimming no. motors : 2 motor power : 1.5 KW r.p.m. : 12000 RPM , NO. EDGE PROCESSING UNITS 3 Processing Unit : Corne ...

Single-sided edge banding machine for machining of straight workpiece edges and for banding and post-processing of various edge materials in longitudinal and transverse passing. Automatic conversion from radius to chamfer and different edge and workpiece thicknesses. Control Power Control PC 22 OVERVIEW OF UNIT ASSEMBLY: – RELEASE AGENT SPRAYING UNIT – JOINING MILLING UNIT – GLUING PART A20 WITH 2 ROLLS Application unit PU 65 (Teflon-coated for PU gluing) – CROSS-CUT UNIT HL84 – PRE-MILLING UNIT – FK11 SHAPE MILLING UNIT – FREE SPACE UNI MILLING UNIT UF10 – PROFILE SCRAPER PN10 – FINISHING UNIT (with detergent information) – Feed rate 20 m/min – Total length 8635 mm 2. WORKPIECE AND EDGE PARAMETERS: – Workpiece width min: – For workpiece thickness 12-22 mm ¦ 60 mm – For workpiece thickness 23-40 mm ¦ 105 mm – Workpiece protrusio ...

Description: Technical data: tape thickness: 0.3 - 3 mm material thickness: 8 - 60 mm conveyor speed: 18 - 25 m / min The edgebander consists of the following aggregates: • 2 pre-milling machines for material processing (3 kW each) • material heating lamp • glue heating vessel • container with roller for applying glue to the material • push rollers • 2 stripping units (each 0.8kw) • 2 units with radial cutters for processing the upper and lower edges (1.5 kw each) • 2 postforming aggregates • 2 cyclings • polishing brushes with liquid injectors The edging is fully automated, which means that the height of the beam, pre-milling machines, rollers and all the settings of the cutter depending on the thickness of the material and the strip are adjusted on the main monitor.serial number: 0-200-19-0792, edge thickness: 0.3 - 3 mm, workpiece thickness: 8 - 60 mm, Approx. On ...

Description: Type of edging Thin edge Thick edge Solid wood Gluing System PUR Premilling Unit yes Corner Rounding Unit yes Grooving Unit yes Max feed speed 24 m/min Maximum panel thickness 60 mm Operating Units 9 nr Min. panel height 12 mm Max. panel height 60 mm Min. edge thickness 0.4 mm Max. edge thickness 20 mm Max. forward feed speed 24 m/min Top pressure yes Pressure with rubber belt Panel support guides yes No. Panel Sizing / Milling units 1 NO. PANEL SIZING / MILLING UNITS 1 Unit : pre-milling unit automatic timed intervention : yes Gluing system yes glue pot for PUR glue yes premelter for PUR glue yes premelter for PUR glue NORDSON Roller set to press the edge yes with positioning by NC yes No. Edge Processing Units 7 NO. EDGE PROCESSING UNITS 1 Processing Unit : end trimming no. motors : 2 NO. EDGE PROCESSING UNITS 2 Processing Unit : top and bottom rough trimming n ...

Description: Flexline HOMAG PROFI KAL 330/6/A3/S2 edge banding machine  , , , serial number: 0-200-24-9153 is equipped as follows:  , , , HOMAG PROFI TBL 100/35/12 feed table with fully automatic workpiece feeding system WZ10 for workpieces with different dimensions in longitudinal and transverse direction Technical data: - Workpiece length 250 - 2500 mm - Electro-pneumatically controlled cross weigher - Air cushion table ( is not included in the scope of delivery )  , , , 2 HOMAG PROFI KAL 330/6/A3/S2 edge banding machine Technical data: - Universal trimming unit UF11, electro-pneumatically controlled  ,Note: the feedback is not included in the scope of delivery  ,serial number: 0-200-24-9153, workpiece thickness: max.60 mm, feed: 18-25 m/min, joint trimming unit: Ja/Yes, snipping unit: Ja/Yes, fine trimming unit: Ja/Yes, profile trim ...

Overview of equipment: - Workpiece support scissor design with roller support, 1000 mm extendable - Infeed ruler automatically adjustable - Fixed stop side left - Inlet interlock pneumatically controlled - Upper pressure via driven composite V-belt - Height adjustment electric - Workpiece transport device via transport chain with rubber support - Release agent spray unit top/bottom - Joint milling unit 2 x 3 kW - Gluing part A20 with 2 rollers, consisting of workpiece preheating, Quickmelt application unit with quick clamping system, 2-roll magazine, pressure zone C (auto-adjustable, with 1 pre-press roll and 6 repress rollers) - Cross-cut unit HL84 0.8 kW, with autom. Adjustment chamfer/straight as well as pneum. Adjustment flush/protrusion caps - Pre-milling unit 1.5 kW, pneum. Adjustment of bündi/protrusion milling machines - Mould milling unit FK11 with autom. Adjustme ...

Overview of the assembly: - Release agent spray unit top & bottom - Joining milling unit 2 x 4 kW - Glued part with workpiece preheating, 2 rolls, pressure zone C and QA34 application unit for PU with quick clamping system - autom. Adjustment pressure zone - Preparation for Lasertec activation unit - Hl84 cross-cut unit 0.8 KW - pneum. Adjustment pre-milling unit - Pre-milling unit Bf10 1.5 kW - Mould milling unit Fk11 Manual - Autom. Adjustment of chamfer to radius milling machines - Rolling side probe FK - Pneumatic adjustment FA11 for lateral displacement from the working area - Multi-drawing blade MN 21 autom. for a maximum of 5 different profiles. - Finishing unit (glue joint drawing blade and swabbing ridge) - Detergent spray unit top & bottom - powerControl PC22 Workpiece and edge parameters: - Workpiece width without edge min: - For workpiece thickness  ...

Fixed stop side on the left. Brief description of the equipment: - Fixed stop side left - Workpiece transport device - Upper pressure - Control Power Control PC22 - Release agent spraying unit - Joining milling unit, 2 x 3 kW - Gluing part A20 Basic for rolls up to 3 mm and strip goods up to 20 mm, with melting unit with granulate container and quick-clamping system - Cross-cut unit, 2 x 0.8 kW, with pneum. Dissimulation - Lubricant spray agggregat - Pre-milled aggreagt 1.5 kW, pneum. adjustable - Mould milling unit FK13, 2 x 0.4 kW - Universal milling unit 4 kW, controlled, with infinitely variable axis - Multi-plastering device MN21 autom. - Finishing unit FA11, with finishing device, detergent application and buffing unit, pneum. adjustable -Noise protection - Free space for additional processing units Further equipment information: - Machine stand throughout f ...

Description: With Homag workpiece feeder TBL 100/25/12/F and Ligmatech workpiece return unit ZHR 30L/155/F  ,edge thickness: 3 mm, workpiece thickness: 12 -60 mm, feed: 18 m/min, gluing unit: Ja, snipping unit: Ja, rough trimming unit: Ja, fine trimming unit: Ja, profile trimming unit: Ja, universal milling unit: Ja, edge sanding unit: Ja, flat scraping unit: Ja, profile scraping unit: Ja, edge buffing unit: Ja, control: powerControl NC 21, return system: Ja, total power approx: 40 kW, Approx. Onsite Dimension. (l x w x h): 10,000 x 6,000 x 1,700 mm, weight approx.: 4,000 kg

Description: The machine will not be available until around May 2024. Basic machine Continuous machine stand for setting up the processing unit Workpiece support with roller rail, extendable approx. 800 mm Glue roller drive for feed stop Glue container lift for feed stop Workpiece-operated glue container clamping Adjustable infeed guide Pneumatically controlled infeed stop Workpiece transport device Transport chain 80 mm wide Precision running and guide surfaces hardened Transport chain magnetically braked Top pressure driven by composite V-belt Manual height adjustment Digital position indicator Technical data Operating voltage: 400 Volt, 50/60 Hz Feed rate: 18 - 25 m/min Feed rate with FK11 profile cutter: max. 20 m/min Working height: 950 mm Working width for workpiece thickness 22 mm: min. 60 mm Working width for workpiece thickness 40 mm: min. 105 mm Workpiece protrusion: 30 ...

Description: - Inlet ruler with automatic adjustment and extension 500 mm - BONDING PART A20 BASIC - Pressure zone C with automatic adjustment - Release agent spray unit - Pre- and profile milling unit with pneumatic adjustment - Edge sanding unit KS10 - Profile sanding unit top/bottom PS41 / PS42edge magazine with: 2 -fold roller, serial number: 0-200-21-6055, edge thickness: 0,3 - 3 (20) mm, workpiece thickness: 8 - 60 mm, workpiece overhang: 30 mm, feed: 18 - 25 m/min, joint trimming unit: 2 x 3 KW, gluing unit: A20/QA34/C, snipping unit: HL84 (2 x 0,8 KW), rough trimming unit: 2 x 1,5 KW, fine trimming unit: 2 x 0,4 KW, profile trimming unit: FF12 (4 x 0,4 KW), edge sanding unit: KS10 / PS41 / PS42, flat scraping unit: ja / yes, profile scraping unit: MN21 automatic, edge buffing unit: ja / yes, control: Power Control PC 22, return system: Nein / No, Approx. Onsite Dimension. (l x w  ...

1 Quickmelt incl. evaluation device level. Interchangeable heads used, good condition 16 pcs. Interchangeable heads FK 11/13 devices, exchangeable at the top below.

Description: Rubber pads conveyor belt renewed approx. 2022 Annual maintenance by HOMAG incl. various new parts (see photos) Second glue pot (serviced annually) Single-sided machine for joint trimming of straight workpiece edges, gluing and finishing of various edge materials from the roll or as strips, up to 20 m edge thickness, with longitudinal and transverse throughfeed. Fixed stop side on the left. BRIEF DESCRIPTION OF THE BASIC EQUIPMENT: BASIC MACHINE WORKPIECE TRANSFER DEVICE - TOP PRESSURE CONTROL power control PC22 FREE SPACE Joining unit GLUING PART A20 BASIC for rolls up to 3 mm and strips up to 20 mm NOISE PROTECTION CAPPAGGREGATE FREE SPACE for further processing units BASIC MACHINE: Continuous machine stand for setting up the processing units Workpiece support with extendable roller rail approx. 800 m Glue roller drive for feed stop Glue container lift with feed stop G ...

Description: - Edge banding machine - Serial number 02352 - Total installed power 21 KW - Edge thickness from 0.40 mm up to 12 mm - Workpiece thickness from 10 mm to 45 mm - Minimum workpiece length 150 mm - Feed motor 2.20 KW - Control system - IMA 08.376 joint trimming unit, 2 x motor 3 KW-12000 rpm - IMA 283.08 Gluing unit with pot for granulated hot melt adhesive - Pressure unit with (1+5) rollers - IMA 08.415 Cross-cut unit, 2 x motor 0.66 KW-11100 rpm, swivels up to 8° - IMA 08.0555 Rough trimming unit, 2 x motor 1.80 KW-12000 rpm (upper motor missing) - IMA 08.346 Profile trimming unit, 2 x motor 0.50 KW-18000 rpm - IMA 08.519 Profile scraper unit - Flat scraping unit - Milling unit, motor 2 KW-12000 rpm - IMA 08.612 Edge buffing unit, 2 x motor 0.25 KW-1320 rpm IMPORTANT: The return system shown in the photos is NOT included in the scope of deliveryApprox. Onsite Dimension. (l ...

Single sided edge banding machine Brand: IMA Type: COMPACT PC-6220 F Year: 2000 Left hand machine Workpiece transport via a driven transport chain and adjustable top pressure Beckhoff control Need of space LxWxH mm: 7400x1500x2000mm Weight: approx. 3600kg Technical data: Edge material: a) Veneer/coil and strip ware, b) PVC/coil and strip ware c) Solid wood strips min. edge height = approx. 14 mm max. edge height = approx. 55 mm min. edge tickness = approx. 0,4 mm max. edge thickness = approx. 20 mm min. panel thickness = approx. 10 mm min. panel thickness = approx. 16 mm at use of the multi function unit max. panel thickness = approx. 50 mm min. panel width = appprox . 60 mm min. panel length = approx. 150 mm max. strips = approx. 20x50 mm Panel supernatant from the chain conveyor = approx. 35 mm Pneumatic connection: approx. 7 - 8 bar The basic  ...

Description: • Edgebander with return system • Serial number 10347 • Edge thickness in strips up to 12 mm • Edge thickness in roll up to 3 mm • Worpiece thickness up to 40 mm • Adjustable feed speed from 5 m/min up to 25 m/min • Feed motor 5.50 KW • Joint trimming unit, 2 x motor 3 KW • Edge feeder for strips and roll, edge magazine for 6 edge coils • Gluing unit for PUR glue • Pressure group with (1+5) rollers • End trimming unit, 2 x motor • Rough trimming unit, 2 x motor 1 KW • Profile trimming unit, 4 x motor • Profile scraping unit • Flat scraping unit • Edge buffing unit • Milling group • Return system with inclined air table and dimensions 2020 x 1000 mm, motorized belt conveyor with useful dimensions 9000 x 1200 mm, inclined roller conveyor with dimensions 2500 x 1200 mmApprox. Onsite Dimension. (l x w x h): 12,275 x 3,800 x 2,570 mm, weight  ...