hsd spare parts for plastic machinery used for sale

Dryer / Centrifugal Dryer / Dry Cleaner Can be used for pre-shredded plastic waste (hard plastic, films), Throughput depending on the type of material approx. 0.5-2 t/h Drive power 30 kw

Chip press for the recycling and compaction of plastic chips (which are shredded if necessary) from machining by converting them into cylindrical briquettes. When it comes to disposing of PU or EPS chips, the Styrotec briquetting press saves a lot of money and increases profits by turning waste into a resource. The chip press can be installed both indoors and outdoors. Briquette diameter: 55 mm Hopper dimensions (diameter): 1000 mm Throughput: 30-75 kg/h Motor pump power: 5.5 kW Dimensions of the briquetting press: 1,100 x 1,460 x 1,600 mm Weight: 565 kg

Complete Britas filter with many spare parts. Off site, available immediately.

Recycling plant/recycling plant General information • Plant type: PET sorting and washing system for the production of PET flakes • Manufacturer: STF-Maschinen & Anlagenbau GmbH • Year of construction: 2023 • New value EUR 4,970,000.00 • Market value (at location): EUR 3,052,000.00 • Installed in two connected halls incl. foundations • Plant currently not in operation (standstill since 11/2024) Technical key data • Max. configuration: 2,000 kg/h • Max. achievable output in continuous operation: 600 kg/h • Output in test run with good material: >1,500 kg/h • Energy requirement: 650-680 kWh (without hot washing system) Stages of the procedure 1. Feeding of PET material (pressed bales) 2. Coarse sorting via sieve drum 3. Magnetic separation of metallic impurities 4. 2-stage sensor sorting (materials) 5. Manual sorting via sorting belt 6. Mill and  ...

used screening machine, function-tested, immediately available

ZENO shredder type ZTLL 3000 x 2500 For crushing PVC window frames Capacity approx. 10 t/h with screen perforation 50 mm Ø Inlet cross-section: 3000 x 2500 mm Drive: 2 x 132 kW, gearbox with torque cut-off Rotor flight circle: 750 mm Rotor speed: approx. 80 rpm Rotor design: 4 rows (180 pcs.) positive inserts, 80 x 80 x 45 mm on tool holders Rotor Bearing: Pillow Block Bearing Rotor body: hardfaced (wear protection) Water spraying funnel: flat jet nozzles, à 3 l/min at 3 bar Screen design: solid screen basket, reinforced with ribs, with screen quick-change device Counter blade: with cutting gap adjustment and foldable Side walls in the rotor area: replaceable, Hardox material Hopper: 1300 mm high, flared on 4 sides, double-walled with concrete filling, without lid Machine weight: approx. 43,000 kg Control cabinet (loose, for controlling the machine, incl. soft sta ...

We supply service and spare parts for seam and machining centers of the manufacturers Elumatec, Rapid, URBAN, Josting, MAW Nottmeyer and Actual. In particular, electronic components of the following machine types are constantly available. Machining centers / saegen: SLK 118, SBZ 122, SBZ 130, SBZ 131, SBZ 140, SBZ 150, DG 142, DG 204, DG 244, DGL 200, DGL 220, DGL 250, DGL 260, DGL 300 Welding machines URBAN, ACTUAL: AKS 6100, AKS 6105, AKS 6110, AKS 6600, AKS 6605, AKS 6610, AKS 6900, AKS 6910, AKS 6250 Plastering machines URBAN: SV 410, SV 410-B, SV 420, SV 430, SV 430-C, SV 530, SV 530-B, SV 530-C, SV 800, SV 815, SV 820, SV 840 Fluegel fitting machines FBA 2500, FBA 2502, FBA 2504 A machine-specific parameterization of the respective components is possible (software, firmware). We keep the following components constantly available: ferrocontrol IPC E500, E550, ...

List of spare parts for Krauss-Maffei MC3 injection moulding machine (KM 1600 T & 2300 T) 1 Calzoni MRE3100I hydraulic laminating motor reconditioned by FHP 1 LCD screen Voith variable flow triple pump : Type IPV /7-250 and Type : IPV7-200 VT 5041 Power Boards 2 VT-VRPA power cards (Orginal Packaging) 1 VT-VRRA power card (Orginal Packaging) 1 keyboard 1 LCD screen 2 GR 400 cards (Orginal Packaging) 2 AE 501 cards(Orginal Packaging) 1 SE 502 card (Orginal Packaging) 1 IO 502 card (Orginal Packaging) 1 NT 500 transformer 3 heating collars 10 KW

Spare Parts for Printers and Thermoformers Consisting of :- GABLER 702/703 Complete Control Cabinet ILLIG VHW 72 Infeed Adjustment VAN DAM Vane Vacuum Pump Norgren Plugassist Cylinder Skeletal Waste Material Winder 20 x ILLIG RDM 70K Mold Parts for 68mm PP Cups 1 x Plastic Crate Polytype DDM 300 Spare Parts 2 x VAN DAM Goose Neck Cup Feeder, 1 x Inclined Conveyor Cup Feeder 8 x Plate Cylinder Assembley Polytype BDM 301R

2 - K machine

machine in stock!

WEGENER BM 301 plastic bending machine was built in Germany by Wegener International GmbH. The machine was regularly maintained and upgraded throughout its service life. In 2022, a general overhaul was carried out at the machine manufacturer. WEGENER BM 301 is the perfect choice for precision forming of thermoplastic sheets made of, among others, PVC, PC/ABS and PMMA with a maximum thickness of 15 mm and a width of 3050 mm. The machining process is performed by means of heating elements in the form of a lower flat strip and an upper V-shaped strip, which heat the material at a controlled temperature to a plastic state. The material is then bent to the desired angle between 0° and 110°. The use of the highest-quality heating elements ensures efficient and even heating of the material along the bending line. They are moved manually along hardened steel rollers. Repeatable positioni ...

For sale complete line for plastic caps, include: 1. CCM48 with moulds and CVS 2. cooling system 3. slitting machine Perfect condition. Working at moment. Origin Italy.

Key data: 600 , 132 , 35

Manufacturer/Manufacturer: Arburg Type/Type: 370C 600-250 Bau-year year: 1999 Control/Controller: Selogica Clothing Power/Clamping Force: 600 kN Schliessart/Clamping Type: Hydraulisch/Hydraulic Holmabstand/Dist.Betw.Tiebars: 370 mm x 370 mm Plate Groesse/Platen Size: 570 mm x 570 mm WZ Einbauhoehe/Mould hight: min 250 mm Oeff-weg/opening stroke: 500 mm Plate distance max/Max. Open Daylight: 750 mm Snail/Screw size: 40 mm Lifting volume/shot volume: 188 cc/158 gram hp Spez. Spray./injection pressure: 1900 bar General General Motor/Motor Power: 11 kW Heating/heating power: 8.1 kW Dimensions: 4.3 m x 1.7 m x 1.8 m Weichtt/Weight: 3180 kg Screen text/Language: Deutsch/German Additional equipment/Additional equipment

Key data: 800 , 132 , 35

Manufacturer/Manufacturer: Arburg Typ/Type: 370C 800-250 Bau-year year: 2003 Control/Controller: Selogica Clothing kraft/Clamping Force: 800 kN Schliessart/Clamping Type: Hydraulisch/Hydraulic Holmabstand/Dist.Betw.Tiebars: 420 mm x 420 mm Plate Groesse/Platen Size: 570 mm x 570 mm WZ Einbauhoehe/Mould hight: min 250 mm Oeff-weg/opening stroke: 500 mm Plate distance max/Max. Open Daylight: 750 mm Snail/Screw size: 34 mm Lifting volume/shot volume: 144 cc/132 gram hp Spez. Spray./injection pressure: 1820 bar General General Motor/Motor Power: 15 kW Heating/heating power: 8.6 kW Dimensions: 4.2 m x 1.7 m x 1.8 m Weichtt/Weight: 3180 kg Screen text/Language: Deutsch/German Additional equipment/Additional equipment Euromap

Key data: 1300 , 194 , 45

Manufacturer/Manufacturer: Arburg Typ/Type: 420C 1300 kN-350 Bau-year year: 1999 Control/Controller: Selogica Closing Power/Clamping Force: 1300 kN Schliessart/Clamping Type: Hydraulisch/Hydraulic Holmabstand/Dist.Betw.Tiebars: 420 mm x 420 mm Plate Groesse/Platen Size: 605 mm x 605 mm WZ Einbauhoehe/Mould hight: min 250 mm Oeff-weg/opening stroke: 500 mm Plate distance max/Max. Open Daylight: 750 mm Snail/Screw size: 40 mm Lifting volume/shot volume: 182 cc/166 gram hp Spez. Spray./injection pressure: 1670 bar General General Motor/Motor Power: 22 kW Heating/heating power: 8 kW Dimensions: 4.3 m x 1.7 m x 1.8 m Weicht/Weight: 5100 kg Screen text/Language: Deutsch/German Additional equipment/Additional equipment Core Pulling: x1 Euromap Vario

Key data: 1000 , 194 , 45

Manufacturer: Arburg Type: 420 C 1000 - 350 Built: 1999 Control: Selogica Closing type: Hydraulic Closing force: 1000 kN Tie bar ratio: 420 mm x 420 mm Plate size: 570 mm x 570 mm Tool installation height: min 250 mm Opening distance: 500 mm Plate spacing max.: 750 mm Screw: 45 mm Lifting volume: 230 cc / 194 gram PS Spray pressure: 1670 bar General Engine: 22 kW Heating: 8.8 kW Dimensions: 4.3 m x 1.7 m x 1.8 m Weight: 3430 kg Screen text: German

Key data: 1300 , 166 , 40

Manufacturer: Arburg Type: 420C 1300 - 350 Built: 2000 Control: Selogica Closing type: Hydraulic Closing force: 1300 kN Tie bar ratio: 420 mm x 420 mm Plate size: 605 mm x 605 mm Tool installation height: min 250 mm Opening distance: 500 mm Plate spacing max.: 750 mm Screw: 40 mm Lifting volume: 182 cc / 166 gram PS Spray pressure: 2120 bar General Engine: 22 kW Heating: 8 kW Dimensions: 4.3 m x 1.7 m x 1.8 m Weight: 4080 kg Screen text: German Optional extras Robot interface Core pull x2

The BATTENFELD BA 600 CDC injection molding machine was built in Austria in 2002. It is equipped with Unilog B4 control. It has a closing force of 600 kN forms. The screw diameter is 33 mm and the injection volume is 99 cm3. The machine has plates for mounting injection molds with dimensions of 511 x 511 mm, and the clearance between the columns is 320 x 320 mm. The injection molding machine is equipped with a receiving robot, hot runners, a conveyor belt for collecting moldings, four pillows, a string of cores and technical documentation. Technical parameters of the BATTENFELD BA 600 CDC injection molding machine – control: Unilog B4 – dimensions of tool plates: 511 x 511 mm – clearance between columns: 320 x 320 mm – tool height, min. : 150 mm – opening path: 511 mm – injection pressure: 2022 bar – injection volume: 99 cm3 – injection weight: 90 g – screw  ...

Key data: 350 , 41 , 25

Manufacturer: Arburg Type: 221K 350 - 100 Year of construction: 09/2005 Control: Selogica Closing force: 350 kN Locking type: Knee lever Tie bar spacing: 221 mm Plate size: 324 mm x 250 mm Tool height: min 150 mm - 300 mm Opening distance: 200 mm Plate spacing max.: 350 mm - 500 mm Screw: 25 mm Stroke volume: 49 ccm / 41 gram PS Injection pressure: 2000 bar general Engine: 7.5 kW Heating: 4.6 kW Dimensions: 2.7 m x 1.4 m x 2.2 m Weight: 1200 kg Optional extras Core train x1 Hot channel integrated

Manufacturer: Arburg Type: 320 C 500 - 170 Year of construction: 11/2006 Control: Selogica Closing type: Hydraulic Closing force: 500 kN Tie bar spacing: 320 mm x 320 mm Plate size: 446 mm x 446 mm Tool height: min 200 mm Opening distance: 350 mm Plate spacing max.: 550 mm Screw: 35 mm Lifting volume: 115 ccm / 105 gram PS Injection pressure: 1470 bar general Engine: 11 kW Heating: 9.4 kW Dimensions: 3.4 m x 1.4 m x 1.9 m Weight: 2430 kg Screen text: German Additional equipment Core train x1

Manufacturer: Arburg Type: 420 C 1000 - 270 Year of construction: 2007 Control: Selogica Closing type: Hydraulic Closing force: 1000 kN Tie bar spacing: 420 mm x 420 mm Plate size: 570 mm x 570 mm Tool height: min 250 mm Opening distance: 500 mm Plate spacing max.: 750 mm Screw: 35 mm Stroke volume: 144 ccm / 132 gram PS Injection pressure: 2000 bar general Engine: 15 kW Heating: 6.4 kW Dimensions: 4.3 m x 1.6 m x 2 m Weight: 3880 kg Screen text: German Optional extras Core train x1 Robot interface

Manufacturer: Arburg Type: 420 S 800 - 350 Year of construction: 1999 Control: Selogica Closing type: Hydraulish Closing force: 800 kN Tie bar spacing: 420 mm x 420 mm Plate size: 638 mm x 638 mm Tool height: min.250 mm Opening distance: 450 mm Plate spacing max.: 600 mm Screw: 45 mm Lifting volume: 230 ccm / 194 gram PS Injection pressure: 1600 bar general Engine: 18.5 kW Heating: 10,2 kW Dimensions: 4.3 m 1.7 m 1.8 m Weight: 3800 kg Screen text: German Optional extras Core train: x1

Manufacturer: Arburg Type: 470 C 1500 - 350 Year of construction: 2005 Control: Selogica Closing type: Hydraulic Closing force: 1500 kN Tie bar spacing: 470 mm x 470 mm Plate size: 650 mm x 650 mm Tool height: min 250 mm Opening distance: 500 mm Plate spacing max.: 750 mm Screw: 45 mm Lifting volume: 230 ccm / 210 gram PS Injection pressure: 1670 bar general Engine: 30 kW Heating: 10,2 kW Dimensions: 4.9 m x 1.7 m x 2 m Weight: 4600 kg Screen text: German Optional extras Robot Arburg Multilift + 100mm column extension El. Dosing + LGS 6 heating control points Robot interface Core train x1

clamping force: 1.750 kN injection volume: 318 cm³ screw diameter: 45 mm platen size: 700 x 700 mm daylight between platens - max.: 460 mm Condition: used, Specification: Horizontal injection moulding machine, Injection unit: - Screw diameter: 45 mm - Screw length L/D: 20 - Spray volume: 318 cm³ - Shot weight max.: 287 g - Special spraying pressure: 2,100 bar Clamping unit: - Max. clamping force: 1,750 kN - clamping plates: 700 x 700 mm - Opening path max.: 460 mm - mould installation height: 150 mm - Operating hours: 89217 h - 1x core puller - Handling / Robots: ENGEL The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 700 kN injection volume: 103 cm³ screw diameter: 30 mm platen size: 432 x 310 mm closing stroke: 650 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: -- kN injection volume: 230 cm³ screw diameter: 40 mm platen size: 475 x 475 mm Condition: used, Specification: Horizontal injection moulding machine, injection unit: - Screw diameter: 40 mm - Cylinder diameter: 40 mm - Spraying volume: 230 cm³. Clamping unit: - tie bar distance: 475 x 475 mm - Operating hours approx.: 30000 h - Air valve - Core pull - 12-way hot runner controller The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 4200 kN injection volume: 572 - 1716 cm³ screw diameter: 90 mm platen size: 1040 x 1040 mm closing stroke: 620 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 500 kN injection volume: -- cm³ screw diameter: 25 mm platen size: 400 x 400 mm Condition: used, Specification: horizontal injection molding machine, - used injection unit: - Screw diameter: 25 mm - shot volume max.: -- cm³ - injection pressure approx.: 1290 bar - heating zones: 4 - Heating power: 4 kW clamping unit: - clamping force: 500 kN - opening stroke max.: 325 mm - platen distance max.: 550 mm - clamping platen size approx.: 400 x 400 mm - tie bar distance: 270 x 270 mm - pump motor: 15 kW - total power: 19 kW - operating voltage: 380V, 50Hz - Weight approx.: 1.870 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

ARBURG 270 S 150-60 U ALLROUNDER MACHINE WAS FULLY SERVICED NOT LONG AGO WITH NEW SCREW TECNICAL DATA IN LIST -PHOTO EUROMAP 150-60

Sell Vacuum pump used Type: Busch 250-138, Vacuum: 20 mbar, Motor Oil: Type SAE30, Engine: Delfin, Year of manuf.: 2012, Power 3,45 kW, 230 volts, 15 A,

clamping force: 800 kN injection volume: 177 cm³ screw diameter: 35 mm platen size: 580 x 580 mm Condition: used, Specification: Horizontal injection moulding machine, type: Ergotech viva 80-400 - Internat. Size specification: 800 - 400 injection unit: - Screw diameter: 35 mm - L/D - ratio: 20D - Injection volume: 177 cm³ - Injection pressure: 2387 bar - Cylinder heating: 8,8 kW clamping unit: - Clamping force: 800 kN - Max. opening stroke: 450 mm - Mould installation height: min. 250 mm - Max. platen distance: 700 mm - Mould clamping platens: 580 x 580 mm - Clear column distance: 400 x 400 mm Total machine: - Oil tank filling: 220 ltr. - Pump capacity: 15 kW - Voltage: 3x 400V, 50 Hz, N, PE - total power: 23,8 kW - Dimensions L/W/H: approx. 4250 x 1270 x 1795 mm - Weight without oil approx.: 3,600 kg - 1x core pull Plant i ...

clamping force: 600 kN injection volume: 106 cm³ screw diameter: 30 mm platen size: 590 x 600 mm Condition: used, Specification: Horizontal injection moulding machine, type: System 60/420-200 - Internat. Size specification: 600 - 200 injection unit: - Screw diameter: 30 mm - L/D - ratio: 20D - Injection volume: 106 cm³ - Injection pressure: 1995 bar - Cylinder heating: 8,3 kW clamping unit: - Clamping force: 600 kN - Max. opening stroke: 450 mm - Mould installation height: min. 250 mm - Max. platen distance: 700 mm - Mould clamping platens: 590 x 600 mm - Clear column distance: 420 x 420 mm Total machine: - Oil tank filling: 180 ltr. - Pump capacity: 22 kW - Voltage: 3x 400V, 50 Hz - total power: 30,3 kW - Dimensions L/W/H: approx. 4200 x 1400 x 2000 mm - Weight without oil approx.: 3,950 kg - 2x core pull Plant is still in ...

clamping force: 1.000 kN injection volume: 203 cm³ screw diameter: 40 mm platen size: 580 x 652 mm Condition: used, Specification: Horizontal 2K-injection moulding machine, injection unit 1: - Screw diameter: 40 mm - injection volume: 230 cm³ - weight: 205 g Clamping unit: - Clamping force: 1000 kN - Centring: 125 mm - Platen size: 580 x 652 mm - Mould size: 400 x 400 mm - Mould thickness min.: 250 mm - Mould thickness max.: 450 mm - 1x core pull - Voltage: 3x 400V, 50Hz, N, PE - Total power: 25 kW - Dimensions L/W/H: approx. 4,350 x 1,400 x 1,900 mm - Weight approx.: 4,750 kg Further DEMAG plastic injection moulding machines and a conveyor control/material station for 4 to 56 separators for granulate conveying on our homepage. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 6500 kN injection volume: 2011 / 323 cm³ screw diameter: 80 / 45 mm platen size: 1450 x 1350 mm Condition: used, Specification: Horizontal 2K-injection moulding machine, DEMAG ergotech 650-5200-610 incl. handling injection unit 1: - Screw diameter: 80 mm - injection volume: 2.011 cm³ - weight: 1810 g injection unit 2: - Screw diameter: 45 mm - injection volume: 323 cm³ - weight: 290 g Clamping unit: - Clamping force: 6500 kN - Centring: 200 mm - Platen size: 1450 x 1350 mm - Mould size: 1000 x 910 mm - Mould thickness min.: 450 mm - Mould thickness max.: 950 mm - 2x core pull - Handling: Yes - Voltage: 3x 400V, 50Hz, N, PE - Total power: 245 kW - Dimensions L/W/H: approx. 10,100 x 5,500 x 5,000 mm - Weight approx.: 36,000 kg Further DEMAG plastic injection mould ...

clamping force: 4200 kN injection volume: 1212 /292 cm³ screw diameter: 70 /15 mm platen size: 1200 x 1100 mm Condition: used, Specification: Horizontal 2K-injection moulding machine, DEMAG Multi 420/810-2300h/430 incl. handling injection unit 1: - Screw diameter: 70 mm - injection volume: 1.112 cm³ - weight: 880 g injection unit 2: - Screw diameter: 15 mm - injection volume: 292 cm³ - weight: 190 g Clamping unit: - Clamping force: 1200 kN - Centring: 160 mm - Platen size: 1200 x 1100 mm - Mould size: 810 x 710 mm - Mould thickness min.: 380 mm - Mould thickness max.: 940 mm - 4 & 4 Cascades - 4x core pull - Handling: Yes - Voltage: 3x 400V, 50Hz, N, PE - Total power: 192 kW - Dimensions L/W/H: approx. 7,900 x 2,200 x 5,000 mm - Weight approx.: 25,000 kg Further DEMAG plastic i ...

clamping force: 800 kN injection volume: 106 / 42 cm³ screw diameter: 30 / 22 mm platen size: 600 x 600 mm Condition: used, Specification: Horizontal 2K-injection moulding machine, injection unit 1: - Screw diameter: 30 mm - injection volume: 106 cm³ - weight: 94 g injection unit 2: - Screw diameter: 22 mm - injection volume: 42 cm³ - weight: 37 g Clamping unit: - Clamping force: 800 kN - Centring: 125 mm - Platen size: 600 x 600 mm - Mould size: 420 x 420 mm - Mould thickness min.: 250 mm - Mould thickness max.: 590 mm - Voltage: 3x 400V, 50Hz, N, PE - Total power: 42 kW - Dimensions L/W/H: approx. 4,300 x 1,400 x 3,600 mm - Weight approx.: 5,750 kg Further DEMAG plastic injection moulding machines and a conveyor control/material station for 4 to 56 separators for granulate conveying on our homepage. The data for th ...

Wittman-Battenfeld injection machines 2 units 110tons and one 180t -BTT110 - BT110 - BT180

M. No.: 12088 10 Performance: 125 cups per min. (gross) Consists of: -Destacker -Bottom label dispenser -Side label dispenser 1 + 2 and 3 + 4 -Station for finishing the gluing of the side labels (ironing system) -Control station with camera surveillance -Stacker with counter -Outfeed conveyor for finished product The machine can also label round cups (160-180°, around). Cup height: 120-130 mm

clamping force: 600 kN injection volume: 144 cm³ screw diameter: 35 mm platen size: 570 x 570 mm closing stroke: 500 mm Condition: used Specification: Horizontal injection moulding machine clamping unit: - Clamping force max.: 600 kN - clamping platens: 570 x 570 mm - clear column distance: 370 x 370 mm - Distance between the mould mounting platens: 750 mm - Mould installation height: 250 mm - Opening stroke max.: 500 mm - Ejector travel hyd. Ejector stroke: 175 mm - Ejector force max.: 40 kN Injection unit: - Screw diameter: 35 mm - Screw length: 20D - Screw stroke max.: 150 mm - Max. dosing volume: 144 cm³ - Moulded part weight: 121 g - Injection pressure: 1,820 bar - Injection flow max.: 154 cm³/s - Screw peripheral speed: 57 m/min - Screw torque max.: 440 Nm - Barrel and nozzle heating: 1600 +  ...

clamping force: 1300 kN injection volume: -- cm³ screw diameter: 45 mm platen size: 470 x 470 mm Condition: used, Specification: Horizontal injection moulding machine, Type: Allrounder 470 S 1300-350 Injection unit: - Screw diameter: 45 mm - Centring ring diameter: 125 mm - Shot weight max.: 210 g (PS) - Injection pressure: 1,840 bar Clamping unit: - Clamping force: 1300 kN - Opening stroke max.: 850 mm - Mould installation height: min. 275 mm - Mould mounting platens: 470 x 470 mm - Operating hours approx.: 91,000 - Core pulls: 1x - Valve gate: 1x pneumatic - Hot runner control points: 12x - Temperature control unit interfaces: 6x (20 mA) - Conveyor belt in the machine - Selector unit. available - Release for high temperature up to 450°C - Communication card for ProSeS interface available - Robot interface available. Technical pr ...

Key data: 3200 , 700 , 60

Screw diameter; 60 mm Injectable volume: 792cm3 Injection pressure: 2500 bar Column width: 720 x 720 mm Minimum mould thickness: 300 mm max: 700 mm Aperture stroke: 700 mm Cores: 3 Robot Interface: YES Options with ARBURG robot

Spare parts for Battenfeld injection moulding machines The parts are 100% original and functional, and above all, much cheaper than new parts • Control units •Screens • Pressure transducer • Smart cards •Modules •Power supplies •Switches •Keyboard • Temperature controllers • Amplifier Cards •Transducers • Pressure switches • Hydraulic motors • Hydraulic pumps •Manometers • Oil coolers • Proportional valves • Safety valves • Directional valves • Water faucets

Sturtz welding and cleaning line Left-to-right direction SE-HSM-30/26 Compact 0.2mm 3000x2600mm P-260-WST 4AS-JC WST 25

Year: 2015 - technically efficient, ready to work – after full service - working dimensions: 2800 x 1350 mm - tilting stop pins - pneumatically tilted - sliding/brush strips - pneumatic gun DGS 3100 - pneumatic screw feeder ASS 60

Ref. no.: 16369 Manufacturer: BATTENFELD Year of construction: 2005 Clamping unit Clamping force: 75 ton Opening stroke: 800 mm Distance between tie bars: 405 x 405 mm Mould height min.: 150 mm Mould height max.: 480 mm Injection unit Screw diameter: 18 mm Injection volume: 30 cm³ Shot weight: 27 g Injection pressure: 2440 bar Measurements and weight Dimensions: 4,5 x 1,7 x 2,0 m Machine weight: 4500 kg Further information: BATTENFELD EM 75/120 UNILOG B4 All-Electric Precision Injection Moulding Machine The BATTENFELD EM 75/120 UNILOG B4 is a high-quality Austrian-made all-electric injection moulding machine. The BATTENFELD EM series was considered one of the most advanced servo-electric machine concepts of its time and was specifically designed for energy-efficient and highly precise production processes. All major machine movements are driven by modern servo motors, providing: very l ...

Key data: 50 , 1 , 14

Manufacturer: Battenfeld Type: Microsystem 50 Year of production: 2000 Control: Unilog B4 Closure Type: Knee Closing force: 50 kN Maximum mold dimensions: 196 mm x 156 mm Plate Size: 196mm x 364mm Tool height: min 100 Opening Distance: 200mm Maximum distance between plates: 300 mm Screw: 14mm Stroke Volume: 1.1 ccm / 1 gram PS Injection pressure: 2500 bar General Total power: 2 kW Dimensions: 1.9 m x 0.8 m x 2.4 m weight: 1100 kg On-screen text: German Accessories: • Rotary table, • Robot integrated with the machine, • Fully electric injection molding machine, • Quality monitoring module, • Cleanroom module, • In-mold pressure control • Quiet operation of the machine • Additional 14 mm auger

Key data: 2000 kN, 240 g/PS, 45 mm

Arburg 520 C - Allrounder 2000-675 -Injection molding machine - Control: Selogica - Handlebar spacing: 520 x 520 mm - Handlebar extension: 100 mm - Tool installation height: 350 mm - Opening travel: 650 mm - Centering: 125 mm - Core pull: 2 - Screw diameter: 45 mm - Shot weight - HP : 240g - Clamping force: 2000 KN - Operating hours pump: 61908 - Automatic operating hours: 55566 - Working position: Standard

Key data: 7000 kN, 40 mm

Engel E-DUO 740H/740L/700 combi BJ./YEAR 2017 approx. 3871 hrs/h Machine overview: Clamping force: 7000 kN Screw diameter: 40 mm Screw speed: 300 rpm Dosing stroke: 200 mm Control: Engel CC300 Weight: 22 tons Hours: 3871 hours Features: Electric 6-Station Turntable Electrical quick adjustment for the machine plate stroke Two injection units, each with 3-zone screw (D45 mm) 32 zones for hot runner control Electric plasticizing units Full documentation included Status: Ready for use (used) Hours: 3871 Condition of the machine: Already disassembled Defects or missing parts: No known defects, regularly serviced Technical documentation: Complete and available (can be consulted on site)

Key data: 2500 kN, 40 mm

Manufacturer: ARBURG Type: Allrounder 630 H 2500-400 Control: Selogica Year of Make: 2019 Technical data closing page Clamping force: 2500 kN Wooden dimensions h x v: 630 x 630 mm Panel size h x v: 900 x 900 mm Min. installation height: 300 mm Max. installation height: 750 mm Plate spacing max.: 1300 mm Opening travel: 550 mm Ejector stroke: 225 mm Ejector force: 86 kN Centering of movable plate D: 160 mm Centering fixed plate D: 160 mm Technical Data Spray Side Screw diameter: 40 mm Displacement: 201 cc Spray pressure: 2000 bar Worm torque: 550 N Outdoor injection flow: 251 g/s hp Dimensions & Weight Machine dimensions LxWxH: 7.05m x 2.05m x 2.35m Total Weight: 13050KG Equipment Screen text German CEE socket 16A Machine including handling Machine with water battery Machine without material hopper Machine without protective enclosure Levelling elem ...

Key data: 900 kN, 42 mm

Dr. BOY 90 E Stock No.: 503581 Manufacturer: BOY Type: 90 E Control: Procan ALPHA Year of Make: 2013 Hours: 32768 h Technical data closing page Clamping force: 900 kN Wooden dimensions h x v: 430 x 360 mm Panel size h x v: 635 x 610 mm Min. installation height: 250 mm Plate spacing max.: 725 mm Opening travel: 475 mm Ejector stroke: 130 mm Ejector force: 20 kN Centering of movable plate D: 110 mm Centering fixed plate D: 110 mm Tool weight: 800 kg Technical Data Spray Side Screw diameter: 42 mm Capacity: 157.8 cc Spray pressure: 2347 bar Screw length: 20 l/d Screw stroke: 155 mm Screw speed: 280 min Worm torque: 735 N Plasticizing current: 136 g/s PS Number of heating zones: 4 Nozzle travel: 250 mm Dimensions & Weight Machine dimensions LxWxH: 4.37m x 1.21m x 2.2m Total Weight: 3730KG Equipment Screen text German Levelling elements EUROMAP 67  ...

Key data: 5000 kN

Offer(4x): Engel Duo 1800/500 BJ./YEAR 2016 38500h

Year: 2008 - technically efficient, ready to work – after full service - chiseling up + down - PLC control - feeding table

Clamping force: 1250 kN Ø worm: 35 mm Column spacing: 470 mm Injection weight: 142g Min. mould height: 300 mm Total weight: approx. 6,000kg

Key data: 4000 kN, 80 mm

Machine + Viper Robot 12

Injection molding machine

Injection molding machine

Special price because without dukumentation / without disc without funnel +VAT (reclaimable) R1277 Injection moulding machine Arburg A 270 Hydronica D-Version Dialogica topZustand screw D 30mm with device for injection into the parting plane a viewing is desirable by appointment Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any liability for compliance with all requirements mentioned in the UVV (accident prevention regulations).

R1317 Injection moulding machine ARBURG A 221 - 250 - 55 Year of manufacture 1997 Control Multronica with handling device without hopper and water distributor converted to CF drive but without card, with operating instructions for Arburg and one for the robot Machine was freed up by the purchase of new machines. but no function check from us Price free loaded on truck € 1950.-- +VAT a viewing is desirable Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any guarantee for compliance with all requirements mentioned in the UVV (accident prevention regulations).

Price 4.900+VAT (claimable)free loading on truck Injection molding machine Locking force 200t Distance between the spars 520 x 520mm Screws D.=50mm = Injection weight in hp 297gr. Machine very well preserved comes from medical equipment manufacturer Dissolution of injection molding department .with operating instructions and 2 discs. Viewing by e-mail appointment is desirable Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any liability for compliance with all requirements mentioned in the UVV (accident prevention regulations)

A welding machine Pfaff including a rotary shear Kuris and an unwinding device MK is available. 1) Welding machine Pfaff 8309. 2) Rotary shear Kuris BOM 101. 3) Unwinding device MK Sewing Technology Systems. Documentation available. An on-site inspection is possible. The system is dismantled and ready for loading.

Key data: 850 kN, 40 mm

R1295Injection moulding machine ARBURG 320-850-210 Multronica Screw D=40mm Locking force 85 t.Converted from floppy disk drive to CL drive Viewing by e-mail appointment is desirable Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any liability for compliance with all requirements mentioned in the UVV (accident prevention regulations)

Year: 2006 technically efficient, ready to work – after full service 3-spindle (high-speed motors) possibility of setting for various profiles (frame / sash) pneumatic profile clamping

Injection moulding machine Engel e-motion 2440/380 T BJ 2008

2 x Husky HL500RS80 2016 injection moulding machines

Injection moulding machine Krauss Maffei KM 50/90 C2 BJ 2001

2 x Injection Molding Machines Manufacturer. Arburg Type : 270S-250-60 BJ 1996

Netstal Elion 800 injection moulding machine with Wittmann Handling Primus The machine is fully functional and has only 6500 operating hours

Injection moulding machine Arburg 470C 2000-675 BJ 2007

Injection moulding machine Krauss Maffei KM 300-1900 C2 BJ 2000

Injection moulding machine Arburg 420S 1300-350 BJ 2000 without handling

Injection moulding machine Demag erg. 250/560 840 BJ 2001

GAMMAMECCANICA Compac 125 mm. Construction year 1998 Including Loading conveyor belt, Metal detector, Compactor with driven haul off for reels, master dosing unit Engin Plast, Extruder 125 mm diam. 36 L/D with degassing pump d.c. Ansaldo drive 197 kW, Total installed power 501 kW motor, BD plast non-stop screenchanger diam. 200 mm, hydraulic power station, water ring pelletizer M 8500, Electrical cabinet, Type of machine: GAMMAMECCANICA PLASTIC RECYCLING LINE 125 mm.

Year: 2007 - technically efficient, ready to work – after full service - SV 530 cleaning machine - AKS 1610 welding machine - TBA-F 26/25 cooling station - WT 530 turning station - Welding dimensions: 2300 x 3500 mm - Flash limit: 0.2 – 2 mm - Seal formers

Injection Molding Nose Demag ergotech 50/370-200 BJ 2000

Injection moulding machine Engel victory 200H/200V790 comb BJ 2018

Ideal for operating a business where power outages are not desired, for example injection molding R1334 Power Generator Emergency Power Generator POLYMA/DEUTZ 80 KVA installed in a truck trailer single-axle, was used on construction sites. Dirty outside by leaves and dirt Polyma Kassel 80KVA = 16A = 64 KW,Diesel engine Deutz type F6L912 7ßKW 95hp 2000 rpm., With diesel hand pump hose in canister and pump,With cable/plug 63 A, The trailer is not soundproofed, stood outdoors for years under canopy and is accordingly polluted More detailed pictures on request

injection molding machine Angel Type: Victory 330/80 Tech Machine No: 155871 Age : 2005

Injection moulding machine Krauss Maffei KM 200-1400 C2 BJ 2000

Key data: 20000 kN

Angebot/Offer: Engel Duo 17060/2000 Viper Robot 60 approx. 4900h YOC 2021

URBAN AMS 6010 very good condition fully operational

Key data: 6500 kN, 105 mm

Location is : Latino America !

PLASTIC WASHING. LINE for GRAVIMETRICAL SEPARATION, including:, collection hopper, auger, STAINLES STEEL GRAVIMETRICAL SEPARATION TANK, size mm.5.800 x 1.600 ca, n.4 moving rolls, sinking screw, drained screw for collection of floating material, n.2 additional sinking screws, lifting screw for sunk material, n.2 TECNOFER CENTRIFUGAL DRYERS in sequence, 18,5 kw, 720 x 1.500 mm, connection screws, collection hopper, sucking unit, The line is offered as is, where is, Vertical mixer available separately, capacity: ca.500 kg/h depending on material and contamination

Key data: 1500 kN, 415 g/PS, 55 mm

Built in 1999 Clamping force: 150 tons. Screw diameter: 55 mm Displacement: 456 cm³ Spray pressure: 1564 bar Very good condition!

clamping force: 1500 kN injection volume: 141 g/PS screw diameter: 35 mm platen size: 470 x 470 mm Condition: used, Specification: horizontal injection moulding machine, Type: Allrounder 470C 1500-400 GE GOLDEN EDITION Injection unit: - Screw diameter: 35 mm (wear-resistant) - Centring ring diameter: 125 mm - Max. shot weight: 141 g (PS) - Injection pressure: 2,500 bar Closing unit: - Clamping force: 1,500 kN - Max. opening stroke: 750 mm - Mould installation height: min. 250 mm - Mould clamping plates: 470 x 470 mm - Approx. operating hours: 79,000 h (still in use) - Operating voltage: 3x 400 V, 50 Hz - Nominal motor heating current: 75 / 40 A - Total current: 115 A - Total connection: 65 kW - Core pulls: 1x - Hot runner control points: 6x - Temperature control unit interfaces: 6x (20 mA) - Approved for high temperatures  ...

Year: 2006 - technically efficient, ready to work – after full service - possibility of mounting 3 milling heads - top and bottom chiseling - control via PLC - automatic machining process

Year: 2000 - technically efficient, ready to work – after full service - 4 heads - support arms