We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
SMT Lathe 80001350 The machine was designed and manufactured to produce rotor shafts for power tools. The machine is designed and manufactured to perform the following operations automatically. - Load/unload parts automatically from/to tool carrier line with a pick-up & placement unit between the shaft ends. - Rotate ring seat + flat rotate commutator + rotate commutator. - Ring mounting - Commutator side - Ring mounting - Drive wheel side The machine has several production programs to produce different parts. Each program uniquely corresponds to a wave type Specifications Anchor wavelength from up to 92.5 - 163.1 mm Bearing pin diameter commutator side 8; 10; 12.5 mm Drive side 12; 8 mm Min. Available length bearing position 3.6 mm Package diameter 52; 55; 59 mm Ring dimensions Outer diameter 40 - 57.4 mm Inner diameter 37.4 - 56 mm Ring width 4 - 8 mm R ...
used
Tables for hydrsulic press for clamping on the stump or for the edition on the table. Multiple available. The tables are from a 420to press with installation height 1,250mm The round tables have a continuous opening in the middle. More data and photos on request
used
Description: Machine number: 1317-657 Basic functions: 4 zones (3 preheating zones, peak 1-stage with underside heating) Condensate trap in the bottom cooling zone Control system type C-Dias Technical data: Process chamber: Length: 3304 mm Preheating zones: 3 Peak zone (top / bottom): 2 heating modules / double peak (1 / 1) Bottom heating preheating zone (option): 2 Heated process length, total: 2081 mm Active convection section: 1533 mm Cooling zone length: 1223 mm Temperature detection: NiCr-Ni sensor in the gas flow Heating time: approx. 30 min Heat-up time with power limitation: approx. 60 min Heat transfer: 100 % forced convection Process temp. (preheating zone / peak zone): max. 300 °C / 350 °C (peak) Transport chain: Usable working width with LP support: 60 - 460 mm Usable working height LP support: Cam level / PIN level ... - 10 mm Free passage height (top / b ...
used
Colored Steel Roll Forming Machine is mainly used in the production of colored steel sheets. The machine is artistically made and transmits smoothly at a low noise. It is a kind of very welcomed modern building material with better anti-press and anti-bending performance, and is widely used in the building of garden like factories, civil-construction and mansions, etc. Its length is set according to customerâs requirements and transportation situation. Its color is selected from the color code of the steel factory.
used
Capacity: 700 t Table length: 5000 mm Table width: 5000 mm Stroke: 2000 mm CNC Brand: Siemens CNC Model: Siemens Simatic Playback Max. product5000 Ø Max. plaatdikte28 mm Max. bordel radius700 mm Min. product Ø800 Min.plaatdikte4 mm Min. bordel radius35 mm Werksnelheid190000 mm/min. Vermogen kW140 kW
used
Capacity: 50 t Table length: 2200 mm Table width: 2200 mm Stroke: 800 mm Max. product2200 Ø Max. plaatdikte10 mm Max. bordel radius150 mm Min. product Ø800 Min.plaatdikte3 mm Min. bordel radius25 mm CNC Controll MIPC Q Playback with GAP control Large package TOP rolls 5 units Large package forming & pressure rolls 5 units Loading attachment Unloading attachment Under power out put 6 units Controllable forming roll drive Hydraulic displacement drive Clamping device without hole Basket bottem Knocker bottom Pressure vessel bottom Boiler bottoms Flat floor Plate base diffuser bottom Tank bottom Tank bottom Radar reflectors Engine parts Dispense air Silo hoppers Cooker hoods Container parts Hemispheres
used
Material thickness: 0 mm Throat: 7000 mm
used
turning diameter: 720 mm turning length: 2250 mm control: CNCN 300 turning diameter over bed slide: 480 mm 3-jaw-chuck diameter: 650 mm total power requirement: 44 kW weight of the machine ca.: t dimensions of the machine ca.: m Voltage 380VHertz 503-jaw chuck ø (mm) 650 Including: Turret, 9 positionChip conveyor The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
turning diameter: 720 mm turning length: 2250 mm control: CNCN 300 turning diameter over bed slide: 480 mm 3-jaw-chuck diameter: 650 mm total power requirement: 44 kW weight of the machine ca.: t dimensions of the machine ca.: m Voltage 380VHertz 503-jaw chuck ø (mm) 650 Including: Turret, 9 positionChip conveyor The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.