REITZ rb used machines

Stirring tank REITZ RB300LRW037250 Stainless steel tank 300 liters with agitator 0.37 KW, used gear motor KEB 30 rpm. Stainless steel stirring tank 300 liters with outlet tap 3/4-inch. Diameter 630 mm, container height 990 mm. Tripod height 425 mm. Gear motor: Used gear motor KEB, 3 x 230/400 volts, 0.37 kW, n1 = 1350 rpm, n2 = approx. 30 rpm. With motor protection switch. Shaft: Precision stainless steel shaft D20, length 1000 mm, diameter 20 mm, material stainless steel 1.4301. With rigid coupling 28/20 in stainless steel 1.4571. Stirring organ: Four-bladed inclined blade stirrer, diameter 275 mm, material stainless steel 1.4571. Very slow-running, high-torque agitator.

Agitator 150 litres with gearbox Rexroth 0.18 KW, i = 25 and propeller stirrer 150 mm Container: Single-walled stainless steel container 150 litres with drain tap. Rollable aluminium frame with aluminium profiles 45 * 45 mm. 4 steering wheels, 2 of them with brake. Geared motor: Rexroth, 3 x 230/400 volts, 0.18 kW, i = 25, n2=53 rpm. With motor protection plug. Shaft: precision stainless steel shaft D10, length 850 mm, diameter 10 mm, Material stainless steel Coupling: 2 clamping sets 17 to 10 mm, material stainless steel Stirrer: three-winged propeller stirrer, diameter 150 mm, material stainless steel 1.4581

Used double-walled agitator 47 litres with agitator 0.12 KW Double-walled stainless steel container, approx. 47 litres container volume, externally heated up to 70°C with temperature control unit / water bath Haake DC 10 and circulation pump. With aluminium traverse made of profiles 45 * 45 mm and slow running agitator. Agitator with geared motor: Geared motor Georgii Kobold, 230 volts, 0.12 kW, n1 = 2800 rpm, n2 = approx. 20 rpm. Shaft: precision stainless steel shaft D20, length 300 mm, diameter 20 mm, Material stainless steel. Rigid clutch, bare, material stainless steel Stirring organ: Two-winged slanted blade stirrer, diameter 244mm, material stainless steel. Wings adjustable at angle Electric distribution box with 3 sockets 230V, circuit breaker and FI.

Stirring tank 150 liters with agitator 0.6 KW, 900 rpm and inclined blade stirrer 244 mm Container: Single-walled stainless steel tank 150 liters with drain tap. Rollable aluminum frame with aluminum profiles 45 * 45 mm. 4 swivel castors, 2 of them with brake. Electric motor: Used, powerful electric motor Baumüller, 0.6 kW, 900 rpm, 3 x 230/400 volts. With motor protection plug. Shaft: Precision stainless steel shaft D20, length 700 mm, diameter 20 mm, Material: Stainless steel 1.4301. Coupling: Rigid shaft coupling, material stainless steel 1.4571 Agitator: Double-bladed inclined blade stirrer, diameter 244 mm, material stainless steel 1.4581, blade adjustable in angle.

Used centrifugal blower from Reitz Umwelttechnik – 22 kW, 400 V, 50 Hz - Manufacturer: Reitz Umwelttechnik - Type: MSE 056-009530-00 - Power: 22 kW - Voltage: 400 V, 50 Hz - Volume flow: 95-100 m³/min - Pressure boost: 534-560 daPa - Speed: 2925-2940 rpm (max. 3100 rpm) - Suction temperature: up to 80 °C - Density: 1.205 kg/m³ - Shaft power: 11.5-16.4 kW - Condition: Used, functional. Includes spare engine. - Other blowers with 7.5 kW and 22 kW power available on request.

* General * SKUR0279 * MakeKonrad Reitz Ventilatoren GmbH & Co. KG * LocationBarneveld * CEcheck * TypeKXE 200-002530-00 * Pressure * Pressure buildup0.2 Bar * Main Features * Capacity25 m3/Min * Motor30 KW * Pressure0.2 Bar * Specified Features - Blower * Blowercheck * Capacity1500 M3/h * Motor30 kW 400/690 Volt * With sound absorbercheck * Inletdia. 180mm * Outletdia. 90mm * Information * No.290567 * Year of construction2012 * Floorspace2,3x1,6 M * Total height4,5 M * Weight1250 KgBlowersReitzBlowers > BlowersBrand > Reitz What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

For smaller containers instead of tripod agitators: Agitator REITZ RW0251440200 with 0.25 KW / 1440 rpm and inclined blade stirrer With traverse made of aluminium profiles 45 * 45 mm. Electric motor: 3 x 230/400 volts, 50 Hz, 0.72 A current, 0.25 kW, 1.66 Nm torque, n = 1440 rpm, IP69K, shaft 20 x 40mm, weight approx. 10 kg. Motor protection socket with switch. Shaft: precision stainless steel shaft D20, length 500 mm, diameter 20 mm, Material stainless steel 1.4571 Coupling: Rigid clutch, bare, material stainless steel 1.4571 Stirrer: Two-wing welded inclined blade stirrer, diameter 200mm, material stainless steel 1.4571

Agitator REITZ RW012X244 Agitator 0.12 KW with gear motor ELVEM and 2-wing Inclined blade stirrer 244 mm With traverse made of aluminum profiles 45 * 45 mm. Gear motor: worm gear motor ELKEM, 3 x 230/400 volts, 0.12 kW, n1 = 1395 rpm, IP 55, weight approx. 8 kg. With motor protection plug. Available in 3 agitator speeds: n2 = 14 rpm (i = 100), n2 = 23 rpm (i= 60), n2 = 23 rpm (i= 56). Shaft: precision stainless steel shaft D20, length 1000 mm, diameter 20 mm, Material stainless steel 1.4571. With rigid coupling made of stainless steel 1.4571 Very slow-running, high-torque agitator for use in attachment tanks or cooking kettles.

Electric spindle press REITZ EHSP100F as laboratory heating press / demonstration machine Laboratory heating press with pressing pressure 40 KN (4 tons), ratio 1 : 16, spindle diameter 45 mm, pitch 8 mm, spindle stroke 0.5 mm per revolution. Gear motor 0.75 KW, 1,500 rpm, 4-pole, with spur gear i = 1:5, Speed 150 mm / min. Max dynamic load 25 kN. With reversible control, emergency stop and motor protection plug. Total weight approx. 100 kg, table surface 600 * 600 mm, pressing surface approx. 150 * 250 mm, clear height approx. 60 mm. Base made of high-quality aluminium profiles 45*45 mm, the table top is made of glued plywood top. The laboratory heating press has 40 kN pressing pressure (dynamic load). The spindle is self-locking and thus maintains the pressing force for a longer period of time. For an extra charge with heating plate, insulating plate and tempera ...

Laboratory heating press REITZ EHSP5H – used demonstration machine Heating press with pressing pressure 5 KN (0.5 tons) With heating device up to 200 °C from above and below. - Electric screw press press press force 5 KN (0.5 to) - Screw jack with spindle 20 mm, pitch 5 mm - Gear reduction ratio 1 : 10, 0.5 mm spindle travel per revolution - Clear width approx. 60 mm - Pressing area 100*150mm - Heating device with temperature control, 2 heating plates 100 x 150 mm - With TECO electric motor 0.18 KW - With reversing contactor control (up – down buttons) and emergency stop - Motor protection plug against overload, with main switch - Machine table made of aluminum profiles and multiplex plate 700 * 700 mm - Total weight approx. 100 kg . Suitable for foil bonding and embossing. Due to self-locking of the spindle, long holding time with constant pressure. The s ...

REITZ RW40300400 agitator for tank containers 4.0 KW / 300 rpm and inclined blade stirrer Worm gear motor IE3: Three-phase motor Moll 3 x 230/400 Volt, 4.0kW, IP55, n1 = 1440 rpm, n2 = 300 rpm, worm gear, i = 1:5, plug-in shaft as output shaft D = 28 mm. 5 m cable and motor protection plug. Shaft: Precision stainless steel shaft D30, length 2000 mm, diameter 30 mm, Material: stainless steel. With 2 x 1000 mm pitch and additional rigid coupling. Coupling: 2 pieces rigid coupling, 1x 28/30, 1x 30/30 mm, material stainless steel Agitator: 2 pieces of double-bladed oblique blade stirrers, diameter 400 mm, material stainless steel 1.4571, welded version. Truss: With 1 piece mounting frame approx. 400 mm x 2600 mm Each longitudinal strut 2600 mm consists of 2 mounting rails 41 x 82 mm profile. With diagonal struts and angles for fixation on tank frames. Frequenc ...

Mixing tank 80 liters REITZ MB80 for bulk materials Used open mixing tank approx. 80 liters with geared motor 0.75 KW and inclined blade stirrer 700 mm Application: Mixing of powdered materials. Slow-running, high-torque agitator for powdered mixes. High torque with low energy consumption. Stirred tank: Mobile mixing tank made of stainless steel with bottom slide for draining the mix. All boilers are refurbished and clean. Capacity approx. 80 litres Geared motor: Geared motor Lenze 0.75 KW, 230 / 400 V, 3 phases, 50 Hz, 1410 rpm, IP 55, ratio i = 56, 25 revolutions per minute at shaft output. With motor protection plug to protect the geared motor. Shaft: stainless steel shaft diameter 20 mm, length 500 mm, material 1.4571 Agitator: Double-bladed inclined blade stirrer, diameter 700 mm, material stainless steel 1.4571

Pneumatic laboratory heating press REITZ PHP3 – used demonstration machine Pressed press 3 KN (0.3 tons) With heating device up to 250 °C and temperature control - Press force 3 KN (0.3 to) - Pneumatic cylinder make Festo - Pneumatic two-hand control - Press plate guided in 4 guide columns - Working surface between guide columns 200 * 220 mm - Heating and insulating plate 150 x 250 mm -Temperature - Machine table made of aluminum profiles and PA plate 600*600*60mm - Total weight approx. 100 kg - Mobile with 4 swivel castors, 2 of which with brakes . Suitable for foil pressing and embossing under heat.

Electric surface press REITZ EHSP522 Pressing surface 200*200mm Pressure 5 KN / 0.5 tons Suitable for surface bonding of plastics and composites. On request with: - Heating plate and temperature control - Load cells and gauges for use as test press

Centrifugal fan REITZ MXE 125-016030-00 Type GR 90° direct drive 45 kW m³/min 160 mm WS 1250 Intake ø 350 mm, outlet ø 275 Workshop tested, very good condition

Manual Heating Press Reitz MHSP5H - Manual Lifting Screw Press Static Press Force 5 KN (0.5 to) - Portable press frame made of polyamide PA 6G - Manual screw jack with spindle 20 mm, pitch 5 mm - With handwheel diameter 120 mm and handle - Gear reduction ratio 1 : 10, 0.5 mm spindle travel per handwheel revolution, thus only very little hand force required for high pressure. - Table size 100*150mm - Clear width 60 mm - Punch size diameter 70 mm with 4 holes 8 mm to attach the Hotplate - Very easy operation due to spindle and worm gear - Total weight approx. 25 kg With 2 electric aluminum heating plates 1200 watts, heating area approx. 150 * 100 mm to 250°C, connection 230 V. With sensor and temperature control. Pressure-resistant insulating panels at the top and bottom for use in presses. Suitable for pressing, welding and gluing.

Pneumatic laboratory heating press REITZ PHP3 – used demonstration machine Pressed press 3 KN (0.3 tons) With heating device up to 250 °C and temperature control - Press force 3 KN (0.3 to) - Pneumatic cylinder make Festo - Pneumatic two-hand control - Press plate guided in 4 guide columns - Working surface between guide columns 200 * 220 mm - Heating and insulating plate 150 x 250 mm -Temperature - Machine table made of aluminum profiles and PA plate 600*600*60mm - Total weight approx. 100 kg - Mobile with 4 swivel castors, 2 of which with brakes . Suitable for foil pressing and embossing under heat.

Centrifugal fan REITZ type MAE 045-017030-00Fabr. No. 601438 year of construction 2017Volume flow 10200 m³/h = 170 m³/min. Pressure p 1.2 kg/m³Air inlet 300 mm (nozzle diameter in the base plate)Air outlet 345 x 345 mmEngine speed 2940 rpm. Motor power 18.5 kWNet connection 400 Volt 50 Hz- fan wheel with 8 fan blades- directly flanged drive motor- flange dimensions for air outlet 450 x 450 mm- stable metal housing made of 8 mm steelSpace requirement L x W x H 1930 x 1240 x 950 mmWeight

Centrifugal fan REITZ type: MAE 031-007130-00Fabr. No. 601475 year of construction 2017Volume flow 4260 m³/h = 71 m³/min. Pressure p 1.2 kg/m³Air inlet 250 mm (nozzle diameter in the base plate)Air outlet 245 x 195 mmMotor speed 2915 rpm. Motor power 7.5 kWNetz connection 400 Volt 50 Hz- fan wheel with 9 fan blades- directly flanged drive motor- flange dimensions for air outlet 310 x 260 mm- stable metal housing made of 5 and 6 mm steelSpace requirement L x W x H 1390 x 1030 x 600

Radial fan, centrifugal fan, centrifugal blower, chip extraction fan, fan, suction, chip blower, high performance fan -Manufacturer: Reitz, radial fan chip extraction fan type MXE 020-018030-00 -Engine: Dutchi DM 160 MX2 15 kW -Speed: 2935 rpm -Volume flow: 180 m³/min / 10800 m³/h -Connection input: Ø 245 mm -Connection output: Ø 390 mm -Dimensions: 1460/1160/H1500 mm -Weight: 392 kg

Radial fan, high-pressure radial fan, pressure blower, vacuum blower, ventilation blower, blower, radial blower, side channel blower -Manufacturer: Reitz, Radialventilator -Type: MXE 100-010030-00 -Engine power: 22 kW / 3000 rpm -Volume flow: 100 m³/min -Pressure increase: 1000 daPa -Connection input: Ø 275 mm -Connection: Ø 220 mm -Dimensions: 870/1220/H1210 mm -Weight: 370 kg

The small laboratory press MHSP5 can perform very well with the round stamp (70 mm diameter) deformations of many materials. By delivering fine (0.5 mm per wheel revolution), deformations are carried out very accurately. Small punching or stamping operations are possible. The press is driven by a worm gear screw jacks, which requires minimal hand strength by high reduction ratio. The pressing frame consists of stable-dimensioned polyamide PA6G. Here are some technical data:-static force 5 KN (0.5 to) - portable presses frame made of polyamide PA 6 G, very stable design, with FEM program added - spindle manual jacks 20 mm, pitch 5 mm - with Handwheel diameter 120 mm and handle - gear ratio 1:10, per the Handwheel 0.5 mm screw - table size 235 * 195 mm - clearance width 190 mm - stamp size diameter 70 mm with 4 holes 8 mm for mounting a major stamp Very easy operation with spindle and  ...

Agitator 0.37 KW, 400V, 1340 RPM Coupling aluminium Agitator shaft d = 14 mm, L = 500 mm, stainless steel 1.4301 Stirrer stainless steel, with angle-adjustable angle leaves, d = 244 mm, angle blade width 50 mm, stainless steel 1.4301

Plate press - table press - Laboratory Press - Universal Press MHSP522 Press area 230 * 230 mm Clear width 200 mm Manual drive with worm gear screw jacks 5 KN Pressure 5 KN (0.5 tons) Weight 55 kg Per sensor revolution 0.5 mm path, this little manual force with great force, very fine deliverable. Pressing force is long maintained by self-locking.

Test press for single-axial pressure tests from 0 to 10 KN (0 to 1,000 KG) Purpose: Test press for single-axial pressure tests from 0 to 10 KN (0 to 1,000 KG / 10 KN maximum load). Without distance measurement. Manual lifting spindle press - Static pressing force 5 KN (0.5 to) - Portable, stable press frame made of polyamide PA 6G - Manual spindle stroke gearbox with spindle 20 mm, incline 5 mm - With handwheel diameter 120 mm and handle - Gearbox reduction 1: 10, per handwheel revolution 0.5 mm spindle path - This requires only very low hand force. - Table size 235 * 195 mm - Light width 190 mm - Stamp size diameter 70 mm - With 4 holes 8 mm for fixing a larger stamp plate - Very easy to operate by spindle and worm gearbox - Total weight approx. 25 kg Force measuring device: Weighing module with shear rod load cell for nominal load 1,100 kg. ...