REITZ ehsp used machines

Electric spindle press REITZ EHSP100F as laboratory heating press / demonstration machine Laboratory heating press with pressing pressure 40 KN (4 tons), ratio 1 : 16, spindle diameter 45 mm, pitch 8 mm, spindle stroke 0.5 mm per revolution. Gear motor 0.75 KW, 1,500 rpm, 4-pole, with spur gear i = 1:5, Speed 150 mm / min. Max dynamic load 25 kN. With reversible control, emergency stop and motor protection plug. Total weight approx. 100 kg, table surface 600 * 600 mm, pressing surface approx. 150 * 250 mm, clear height approx. 60 mm. Base made of high-quality aluminium profiles 45*45 mm, the table top is made of glued plywood top. The laboratory heating press has 40 kN pressing pressure (dynamic load). The spindle is self-locking and thus maintains the pressing force for a longer period of time. For an extra charge with heating plate, insulating plate and tempera ...

Electric surface press REITZ EHSP522 Pressing surface 200*200mm Pressure 5 KN / 0.5 tons Suitable for surface bonding of plastics and composites. On request with: - Heating plate and temperature control - Load cells and gauges for use as test press

Laboratory Heating Press EHSP20H – Used Demonstration Machine Table press / electric screw press with pressing pressure 20 KN (2 tons) With heating device up to 200 °C from above and below. Press drive with screw jack gear, reduction ratio 1 : 12, spindle diameter 32 mm, Pitch 6 mm, pressing area approx. 100 * 150 mm, clear height and stroke approx. 300 mm. Geared motor 0.37 KW, 1,390 rpm, 4-pole, with spur gear i = 1 : 5, Speed 150 mm / min. Max. dynamic load 20 kN. With reversing control, control box and motor protection plug. Sturdy press frame made of steel. Undertable made of high-quality aluminium profiles 45*45 mm, table surface 600*600 mm, Table top made of multiplex board. Total weight approx. 100 kg. The table press has a pressing pressure of 20 kN (dynamic load). Typical applications are pressing work with exact lining. Suitable for pressing bonding, e ...

Laboratory heating press REITZ EHSP5H – used demonstration machine Heating press with pressing pressure 5 KN (0.5 tons) With heating device up to 200 °C from above and below. - Electric screw press press press force 5 KN (0.5 to) - Screw jack with spindle 20 mm, pitch 5 mm - Gear reduction ratio 1 : 10, 0.5 mm spindle travel per revolution - Clear width approx. 60 mm - Pressing area 100*150mm - Heating device with temperature control, 2 heating plates 100 x 150 mm - With TECO electric motor 0.18 KW - With reversing contactor control (up – down buttons) and emergency stop - Motor protection plug against overload, with main switch - Machine table made of aluminum profiles and multiplex plate 700 * 700 mm - Total weight approx. 100 kg . Suitable for foil bonding and embossing. Due to self-locking of the spindle, long holding time with constant pressure. The s ...

Used agitator 3.0 KW with long stirring shaft 1700 mm With beam in aluminium profiles 45 * 45 mm. Electric motor: Siemens 3.0 KW, 3 x 230/400 volts, 1420 RPM., IP55. Weight approx. 35 kg. Shaft: precision stainless steel shaft D28, length 1700 mm, diameter 28/30 mm Material stainless steel 1.4301. With 2 rigid couplings stainless steel 1.4301. Stirrer: Prismatic blade, length 300 mm, material 1.4301 stainless steel / polyamide.

The small laboratory press MHSP5 can perform very well with the round stamp (70 mm diameter) deformations of many materials. By delivering fine (0.5 mm per wheel revolution), deformations are carried out very accurately. Small punching or stamping operations are possible. The press is driven by a worm gear screw jacks, which requires minimal hand strength by high reduction ratio. The pressing frame consists of stable-dimensioned polyamide PA6G. Here are some technical data:-static force 5 KN (0.5 to) - portable presses frame made of polyamide PA 6 G, very stable design, with FEM program added - spindle manual jacks 20 mm, pitch 5 mm - with Handwheel diameter 120 mm and handle - gear ratio 1:10, per the Handwheel 0.5 mm screw - table size 235 * 195 mm - clearance width 190 mm - stamp size diameter 70 mm with 4 holes 8 mm for mounting a major stamp Very easy operation with spindle and  ...

Agitator 0.37 KW, 400V, 1340 RPM Coupling aluminium Agitator shaft d = 14 mm, L = 500 mm, stainless steel 1.4301 Stirrer stainless steel, with angle-adjustable angle leaves, d = 244 mm, angle blade width 50 mm, stainless steel 1.4301

Plate press - table press - Laboratory Press - Universal Press MHSP522 Press area 230 * 230 mm Clear width 200 mm Manual drive with worm gear screw jacks 5 KN Pressure 5 KN (0.5 tons) Weight 55 kg Per sensor revolution 0.5 mm path, this little manual force with great force, very fine deliverable. Pressing force is long maintained by self-locking.

Used beater 0,12 KW with gear motor Bauer 27 rpm and aluminum propeller stirrer 300 mm = 1350 RPM gear motor: Gearmotor Bauer, 3 x 230/400 v 0.12 kW, n1, n2 = 27 U/min., 24.5 NM, IP 54 weight approx. 8 kg = M2. With brake. Shaft: precision stainless steel shaft D14, length 500 mm, diameter 14 mm, material 1.4301 stainless steel. With rigid coupling made of aluminium. Stirrer: Double propeller stirrer, diameter 300 mm, material aluminium very slow running, torque mixer for use in attaching containers or kettles. Also can be used to prevent cavities in powder silos (bridging). With traverse for IBC containers or other containers for extra charge. Caution: Not suitable for aggressive media. 3 pieces in stock.

Test press for single-axial pressure tests from 0 to 10 KN (0 to 1,000 KG) Purpose: Test press for single-axial pressure tests from 0 to 10 KN (0 to 1,000 KG / 10 KN maximum load). Without distance measurement. Manual lifting spindle press - Static pressing force 5 KN (0.5 to) - Portable, stable press frame made of polyamide PA 6G - Manual spindle stroke gearbox with spindle 20 mm, incline 5 mm - With handwheel diameter 120 mm and handle - Gearbox reduction 1: 10, per handwheel revolution 0.5 mm spindle path - This requires only very low hand force. - Table size 235 * 195 mm - Light width 190 mm - Stamp size diameter 70 mm - With 4 holes 8 mm for fixing a larger stamp plate - Very easy to operate by spindle and worm gearbox - Total weight approx. 25 kg Force measuring device: Weighing module with shear rod load cell for nominal load 1,100 kg. ...

Agitator 0.25 KW with aluminium propeller 300 mm With traverse made of aluminium profiles 45 * 45 mm. Used electric motor 0.25 KW, 3 x 230/400 Volt, n = 1375 rpm, Weight approx. 15 kg. With motor protection plug. Shaft: precision stainless steel shaft D14, length 500 mm, diameter 14 mm, Material stainless steel 1.4301. Rigid coupling made of stainless steel 1.4571. Stirring organ: Two-wing aluminum propeller d = 300 mm.

Very fast running agitator 0.25 KW - 3400 rpm. with aluminium propeller 300 mm Electric motor: Used electric motor 0.25 KW, 3 x 230/400 volts, n = 3,400 rpm, Weight approx. 10 kg. With motor protection plug. Wave: Precision stainless steel shaft D14, length 500 mm, diameter 14 mm, Material stainless steel 1.4301. Rigid clutch made of aluminium. Stirring organ: Two-flyer aluminium propeller d = 300 mm.

Agitator 150 litres with gearbox Rexroth 0.18 KW, i = 25 and propeller stirrer 150 mm Container: Single-walled stainless steel container 150 litres with drain tap. Rollable aluminium frame with aluminium profiles 45 * 45 mm. 4 steering wheels, 2 of them with brake. Geared motor: Rexroth, 3 x 230/400 volts, 0.18 kW, i = 25, n2=53 rpm. With motor protection plug. Shaft: precision stainless steel shaft D10, length 850 mm, diameter 10 mm, Material stainless steel Coupling: 2 clamping sets 17 to 10 mm, material stainless steel Stirrer: three-winged propeller stirrer, diameter 150 mm, material stainless steel 1.4581

Used double-walled agitator 47 litres with agitator 0.12 KW Double-walled stainless steel container, approx. 47 litres container volume, externally heated up to 70°C with temperature control unit / water bath Haake DC 10 and circulation pump. With aluminium traverse made of profiles 45 * 45 mm and slow running agitator. Agitator with geared motor: Geared motor Georgii Kobold, 230 volts, 0.12 kW, n1 = 2800 rpm, n2 = approx. 20 rpm. Shaft: precision stainless steel shaft D20, length 300 mm, diameter 20 mm, Material stainless steel. Rigid clutch, bare, material stainless steel Stirring organ: Two-winged slanted blade stirrer, diameter 244mm, material stainless steel. Wings adjustable at angle Electric distribution box with 3 sockets 230V, circuit breaker and FI.

For smaller containers instead of tripod agitators: Agitator REITZ RW0251440200 with 0.25 KW / 1440 rpm and inclined blade stirrer With traverse made of aluminium profiles 45 * 45 mm. Electric motor: 3 x 230/400 volts, 50 Hz, 0.72 A current, 0.25 kW, 1.66 Nm torque, n = 1440 rpm, IP69K, shaft 20 x 40mm, weight approx. 10 kg. Motor protection socket with switch. Shaft: precision stainless steel shaft D20, length 500 mm, diameter 20 mm, Material stainless steel 1.4571 Coupling: Rigid clutch, bare, material stainless steel 1.4571 Stirrer: Two-wing welded inclined blade stirrer, diameter 200mm, material stainless steel 1.4571

Agitator RW151000300: 1.5 KW – 1000 rpm. Electric motor: Electric motor Siemens or WEG 1.5 KW, 6-pole, 3 x 230/400 Volt, 1000 RPM, IP55. Weight approx. 30 kg. With motor protection plug. Suitable for frequency converters. Shaft: precision stainless steel shaft D30, length 1000 mm, diameter 30 mm, Material stainless steel 1.4571. With rigid coupling stainless steel 1.4301. Agitator: 4-leaf inclined blade stirrer diameter 300 mm. Material 1.4571. Suitable for larger containers of breweries, dairies etc.

Agitator REITZ RW012X244 Agitator 0.12 KW with gear motor ELVEM and 2-wing Inclined blade stirrer 244 mm With traverse made of aluminum profiles 45 * 45 mm. Gear motor: worm gear motor ELKEM, 3 x 230/400 volts, 0.12 kW, n1 = 1395 rpm, IP 55, weight approx. 8 kg. With motor protection plug. Available in 3 agitator speeds: n2 = 14 rpm (i = 100), n2 = 23 rpm (i= 60), n2 = 23 rpm (i= 56). Shaft: precision stainless steel shaft D20, length 1000 mm, diameter 20 mm, Material stainless steel 1.4571. With rigid coupling made of stainless steel 1.4571 Very slow-running, high-torque agitator for use in attachment tanks or cooking kettles.

Agitator 0.12 KW with used gear motor Bauer 27 rpm and 2-wing Inclined blade stirrer 244 mm With traverse made of aluminum profiles 45 * 45 mm. Gear motor: Used gear motor Bauer, 3 x 230/400 volts, 0.12 kW, n1 = 1350 rpm, n2 = 27 rpm, M2 = 24.5 Nm, IP 54, weight approx. 8 kg. With motor protection plug. Shaft: precision stainless steel shaft D14, length 500 mm, diameter 14 mm, Material stainless steel 1.4301. With rigid coupling made of stainless steel 1.4571 Very slow-running, high-torque agitator for use in attachment tanks or cooking kettles.

Agitator 0.12 KW with gear motor SEVA 89 rpm and 2-wing Inclined blade stirrer 244 mm With traverse made of aluminum profiles 45 * 45 mm. Gear motor: worm gear motor SEVA, 3 x 230/400 Volt, 0.18 kW, n1 = 1340 rpm, n2 = 89 rpm (i = 15), IP 55, weight approx. 8 kg. With motor protection plug. Shaft: precision stainless steel shaft D20, length 1000 mm, diameter 20 mm, Material stainless steel 1.4571. With rigid coupling made of stainless steel 1.4571

Agitator 0.12 KW with gear motor Bauer and 2-wing Inclined blade stirrer 244 mm With traverse made of aluminum profiles 45 * 45 mm. Gear motor: Bauer worm gear motor, 3 x 230/400 volts, 0.12 kW, n1 = 2700 rpm, n2 = 180 rpm (i= 15), IP 55, weight approx. 8 kg. With motor protection plug. Shaft: precision stainless steel shaft D20, length 1000 mm, diameter 20 mm, Material stainless steel 1.4571. With rigid coupling made of stainless steel 1.4571 Very slow-running, high-torque agitator for use in attachment tanks or cooking kettles.

Agitator 0.37 KW 910 rpm and 4-leaf folding stirrer 50 / 150 mm for drums With crossbeam made of aluminum profiles 45 * 45 * 800 mm. Electric motor, 3 x 230/400 volts, 0.37 kW, IP55, 6 poles 910 rpm, With motor protection plug and shielded supply cable. Placed at an angle on truss. Stainless steel shaft D20, length 800 mm, diameter 20 mm, material 1.4571. With rigid coupling, bare, material stainless steel 1.4571 Impeller: Four-bladed folding stirrer, diameter 150 mm unfolded, 50 mm folded, for drums, material stainless steel 1.4571

Mixing tank 80 liters REITZ MB80 for bulk materials Used open mixing tank approx. 80 liters with geared motor 0.75 KW and inclined blade stirrer 700 mm Application: Mixing of powdered materials. Slow-running, high-torque agitator for powdered mixes. High torque with low energy consumption. Stirred tank: Mobile mixing tank made of stainless steel with bottom slide for draining the mix. All boilers are refurbished and clean. Capacity approx. 80 litres Geared motor: Geared motor Lenze 0.75 KW, 230 / 400 V, 3 phases, 50 Hz, 1410 rpm, IP 55, ratio i = 56, 25 revolutions per minute at shaft output. With motor protection plug to protect the geared motor. Shaft: stainless steel shaft diameter 20 mm, length 500 mm, material 1.4571 Agitator: Double-bladed inclined blade stirrer, diameter 700 mm, material stainless steel 1.4571

IBC container agitator 0.75 KW with worm gear motor i = 1 : 10 and inclined blade stirrer 244 mm With truss made of aluminum profiles 45 * 45 mm. Propulsion: worm gear motor, 3 x 230/400 volts, 2800 rpm, 0.75 kW, IP55, n²=280, Weight approx. 25 kg. Shaft: Precision stainless steel shaft D20, length 1000 mm, diameter 20 mm, material stainless steel 1.4301 Coupling: Rigid coupling made of stainless steel 1.4571 Agitator: Double-bladed inclined blade stirrer, diameter 244mm, material stainless steel 1.4571 Sash adjustable angle

Used ATEX agitator RW0252800300 – 0.25 KW – 2800 rpm. For smaller containers and drums. ATEX II 2G EEx e II T3 Electric motor: Electric motor VEM motors Thurm GmbH, 0.25 KW, 2-pole, 3 x 230/400 volts, 2800 rpm, IP55. Weight approx. 8 kg. With motor protection plug. Iso F, suitable for frequency converters. Shaft: Precision stainless steel shaft D10, length 500mm, diameter 10mm, Material: Stainless steel 1.4301. With rigid coupling stainless steel 1.4571. Agitator: Double-bladed inclined blade stirrer, diameter 244mm, Material: Stainless steel 1.4571 With PTB-ATEX test certificate.

Stirring tank 150 liters with agitator 0.6 KW, 900 rpm and inclined blade stirrer 244 mm Container: Single-walled stainless steel tank 150 liters with drain tap. Rollable aluminum frame with aluminum profiles 45 * 45 mm. 4 swivel castors, 2 of them with brake. Electric motor: Used, powerful electric motor Baumüller, 0.6 kW, 900 rpm, 3 x 230/400 volts. With motor protection plug. Shaft: Precision stainless steel shaft D20, length 700 mm, diameter 20 mm, Material: Stainless steel 1.4301. Coupling: Rigid shaft coupling, material stainless steel 1.4571 Agitator: Double-bladed inclined blade stirrer, diameter 244 mm, material stainless steel 1.4581, blade adjustable in angle.