used REHNEN sk

Description: Rehnen Special edge sander Brand: Rehnen Type: SK-1 M-No.: 432 Year of construction: 1999 General specifications: Sanding belt: 2,700 x 150 mm Drive motor: 4 kW Belt speed: 15 m/sec. Table dimensions: 345 x 2,000 mm Dimensions: 3,000 x 2,000 x 1,500 mm Weight: 560 kg Description: Stable universal edge sander for straight, round and curved workpieces Areas of application: radius, shaped parts and straight workpieces Radius sanding with 80 - 300 mm sanding rolls Curved workpieces (allowing R=80 mm to R=1000 mm sanding) for almost all straight and curved workpieces Use of the entire sanding belt by adjustable oscillation Solid work table with integrated dust extraction serial number: 432, Approx. Onsite Dimension. (l x w x h): 2,000 x 1,200 x 1,400 mm, weight approx.: 250 kg

Edge grinding machine Rehnen -new- Type: Junior R 1 with motor band oscillation with support table at the deflection roller Additionally included in the scope of delivery is an angular and miter stop Engine power 2.2 kW Tape speed 22 m/sec Grinding belt dimension 2280 x 150 mm Abrasive back wall 850 x 150 mm Grinding unit swivelable 90 - 180° Grinding belt tension pneumatic Table size 750 x 350 mm The top in heavy casting with built-in three-phase motor 380 V, 2.2 kW 2850 rpm The machine is equipped with built-in switch-plug combination; Motor circuit breaker and main switch according to VDE Dimensions of the abrasive belt rear wall 850 x 150 mm the abrasive back wall is glued with a graphite sliding surface Steel table adjustable in height by spring pressure Grinding belt dimension 150 x 2280 mm The machine is supplied with 2 pieces of grindin ...

Rehnen KBA edge processing machine for grinding, profile milling and profile grinding of edges in one pass Pre-milling unit., processing aggregates: 6, feed: infinitely variable, Connected load: 10 kW, Min. workpiece thickness: about 10 mm, Max. workpiece thickness: approx. 110 mm, Aggregate 1: Pre-milling, Aggregate 2: grind, Aggregate 3: Rounding milling machine above, Aggregate 4: Rounding milling machine below, Aggregate 5: Profile milling machine below, Aggregate 6: Profile grinding below

technical details: - motor band oscillation - pneumatic belt tension - small support table on the pulley - Swivel range grinding track rear wall: 90° - 180° - Dimensions grinding track back wall:850 x 150 mm - Grinding track back wall glued with a graphite sliding lining - Band size: 150 x 2,280 mm - Steel table adjustable in height by spring pressure - Table size: 750 x 350 mm - Belt speed: 22 m/sec - Roll diameter: 140 /80 mm - Diameter suction nozzle: 100 mm - Bracket (included) - Miter stop (included) - Switch-plug combination - Motor protection and main switch according to VDE - Dust tested (GS) Holz-BG-Stuttgart (when connected to an extraction system with an air velocity of at least 20 m/sec) - Weight: 200 kg Sound power level (DIN EN ISO 7346) - No-load: 91 dB(A) - Processing: 91 dB(A) Workplace-related emission value (DIN EN ISO 11202) - No-load: 83 ...

racks: 17; support tube spacing: 60mm; rack length: 650mm; langth: 200 - 2000mm; rolls: Polyamid 4 Stück; depth: 870 - 1180mm; height: 198mm; safe load: 400kg; The user-friendly Varioflex drying rack is a space-saving and gentle solution for storing painted workpieces. The four swivel castors mean that it can also be used for transporting workpieces. Its solid tube frame design can be adjusted between 200 mm and 2,000 mm. With 17 inside and outside plastic-coated support tubes on each side, the rack can support up to 400 kg of evenly distributed weight. The plug-in inside and outside support tubes can be taken out and re-inserted as needed. When not in use, the drying rack can be collapsed and takes up minimal space.

Band width: 150mm; Band length: 2280mm; Table size: 750mm x 350mm; Additional table: 350mm x 300mm; Veneer grinding device: no; Oscillation: yes; Swivel grinding unit: yes; Suction connection: 120mm; Motor power: 2.2 kW; Machine length: 1000mm; Machine width: 800mm; Weight: 200kg;

Plate transport trolley - Swivel from vertical to horizontal position - Hydraulic height adjustment - Support size 2500 x 1500 mm - Load capacity 250 kg Available from January 2024!

Motor output: 3 kW Table dimensions: 350 x 750 mm grinding band dimension: 150 x 2.280 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

SKL regenerates turbocharger Manufacturer: VEB compressor construction Bannewitz (DDR) Type: R2 Equipment Nr. 2227-00008 Register-Nr. 256 n max 52000U/min t max 700 ° C m 95 kg Year of construction: 1973

colstress holder SK50 with inner suit thread In a suitcase with collets according to photos Special price Lid Hermle Weiler Meuser Kunzmann Wanderer Ruhla Weipert Wohlenberg

Praezision clamping tool Kombi plug-on pins BestNo. 1052-018 2 stub SK60x40x27 Unused and ovp 1 x as good condition Only against bid! Special price

Condition: Good, working The Baader 51 skin-removal machine is designed to remove skins from the fillets of cod fish, heke, paltsus and red fish. The machine captures the skin from the tip of the tail without any incision. This provides a higher output of finished products. The width of the pipeline: 380 mm. The fillets are placed on a conveyor belt next to each other. Performance: 50-160 fillets per minute (depending on fillet size and operator skills) Power consumption: 1.5 kW Water consumption: 15 litres per minute The width of the work pipeline: 380 mm Dimensions: 1980 x 780 x 1130 mm Weight (net): 530 kg

Tool holder, milling holder, milling tool -Adjustment: SK50 -Recording inside: Ø 28 mm -Weight: 2.9 kg/piece

Skin area: 345 x 495 mm Part size: Max. approx. 120 mm Carton size: 345 x 495 mm Film width: 390 mm Including roller punch / cylinder punching machine Illig ZSM60 Contact details for ordering SKIN foil and cardboard available. Prior sale reserved - errors possible. Internal Reference Number: D-1149

Item tool holders for milling machine with SK40 (inner suit M16) DIN 2080 SK40-ER16 Long milling mandrels for Horzon valley milling in different diameters, partly with bearings Short milling mandrels for holding cutter heads Recordings with Morse cone in different sizes Everything according to photos

Tool holder, milling holder, milling tool -Adjustment: SK50 -Tool holder: Ø 40 x 40 mm -Brill chucks: flat chucks, reducing sleeves, cutter head, shell end mill, spindle tool -Number: 1x recordings available -Price: per piece -Dimensions: 220/95/H95 mm -Weight: 4 kg/piece

Tool holder, milling holder, milling tool -Adjustment: SK50 -Tool holder: MK2 -Brill chucks: flat chucks, reducing sleeves, cutter head, shell end mill, spindle tool -Number: 1x recordings available -Price: per piece -Dimensions: 190/95/H95 mm -Weight: 3 kg/piece

Tool holder, milling holder, milling tool -Adjustment: SK50 -Tool holder: Ø 22 x 40 mm -Brill chucks: flat chucks, reducing sleeves, cutter head, shell end mill, spindle tool -Number: 1x recordings available -Price: per piece -Dimensions: 210/95/H95 mm -Weight: 3 kg/piece

Tool holder, milling holder, milling tool -Adjustment: SK50 -Tool holder: Ø 22 x 31 mm -Brill chucks: flat chucks, reducing sleeves, cutter head, shell end mill, spindle tool -Number: 1x recordings available -Price: per piece -Dimensions: 220/95/H95 mm -Weight: 3 kg/piece

Tool holder, milling holder, milling tool -Adjustment: SK50 -Tool holder: Ø 22 x 45 mm -Assembled tool Ø: 75 x 50 mm -Brill chucks: flat chucks, reducing sleeves, cutter head, shell end mill, spindle tool -Number: 1x recordings available -Price: per piece -Dimensions: 240/95/H95 mm -Weight: 6 kg/piece

Tool holder, milling holder, milling tool -Adjustment: SK50 -Tool holder: Ø 50 x 55 mm -Brill chucks: flat chucks, reducing sleeves, cutter head, shell end mill, spindle tool -Number: 1x recordings available -Price: per piece -Dimensions: 220/95/H95 mm -Weight: 4 kg/piece

Tool holder, milling holder, milling tool -Adjustment: SK50 -Tool holder: Ø 27 x 60 mm -Brill chucks: flat chucks, reducing sleeves, cutter head, shell end mill, spindle tool -Number: 1x recordings available -Price: per piece -Dimensions: 250/95/H95 mm -Weight: 3 kg/piece

Tool holder, milling holder, milling tool -Adjustment: SK50 -Tool holder: Ø 50 mm -Brill chucks: flat chucks, reducing sleeves, cutter head, shell end mill, spindle tool -Number: 1x recordings available -Price: per piece -Dimensions: 220/95/H95 mm -Weight: 4.5 kg/piece

Tool holder, milling holder, milling tool -Adjustment: SK50 -Tool holder: MK4 -Brill chucks: flat chucks, reducing sleeves, cutter head, shell end mill, spindle tool -suitable for tool changers -Number: 1x recordings available -Price: per piece -Dimensions: 230/95/H95 mm -Weight: 3.2 kg/piece

Tool holder, milling holder, milling tool -Adjustment: SK50 -Tool holder: MK4 -Brill chucks: flat chucks, reducing sleeves, cutter head, shell end mill, spindle tool -suitable for tool changers -Number: 6x recordings available -Price: per piece -Dimensions: 240/95/H95 mm -Weight: 3.0 kg/piece