used NILES dp

Engine lathe NILES DP1/S3 Year of manufacture: 1988 Manufacturer: NILES Made in Germany Machine is almost not used, complete Technical Data: Height of center over bed: 800mm Max. processing diameter over bed: 1.600mm Max. processing diameter over support:1.250mm Min. work-piece diameter: 250mm Max. work-piece weight: 40.000kg Max. work-piece diameter: 1.250mm Internal spindle cone (1:10): 120mm Range of longitudinal support feeds: -1st row (stepless adjustment): 1-200mm/min -2st row (stepless adjustment): 36-3600mm/min Range od feeds of transversal slides: -1st row (stepless adjustment): 0,4-80mm/min -2st row (stepless adjustment): 14,4-1440mm/min Range of feeds of cross slides: -1st row (stepless adjustment): 0,12-25mm/min -2st row (stepless adjustment): 4,5-450mm/min Length of travel: -Of transversal slides: 760mm -Of cross slides: 500mm -Of incisive ca ...

Tip height: 1250 mm Turning diameter: 2,500 mm over bed Centre distance: 4.000 mm Support motion: 750 mm longitudinal feeds 630 mm cross feeds Face plate: Ã? 1250 mm Spindle speed: 5.6-280 RPM. Spindle bore: 100 mm Workpiece weight: 10.000 kg Equipped with: -Floor plates 4.500 x 2.200 mm -Powered tailstock -Operating instructions Country of origin: Germany Engine power: 45 kW Machine weight: 18,000 kg Machine Lxwxh: 8,000 x 4,000 x 2,100 mm

3-jaw-chuck diameter: 630 mm turning diameter over slide rest: 650 mm turning length: 500 mm turning dia. in gap: 1420 mm digital readout: Mitutoyo turning speeds: 3,55-710 U/min total power requirement: 24 kW weight of the machine ca.: 9 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 1650 mm turning diameter over slide rest: 1200 mm turning length: 7500 mm turning dia. in gap: 2500 mm spindle diameter: 105 mm speed: 3,55 - 180 (x24) U/min voltage: 380 V total power requirement: 45 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 4000 mm turning diameter over slide rest: . mm turning length: 5000 mm total power requirement: 30 kW weight of the machine ca.: . t dimensions of the machine ca.: . m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 1650 mm turning diameter over slide rest: 1200 mm turning length: 7500 mm turning dia. in gap: 2500 mm spindle diameter: 105 mm speed: 3,55 - 180 (x24) U/min voltage: 380 V total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Face plate diameter: 1.250mm Center height above foundation slab: 1,250mm Weight: 19t Power: 55Kw Max. torque on the face plate: 31,500Nm Maximum workpiece mass between centres: 16,000 kg Speed range: 2.24 – 224 rpm

Turning diameter: 1300 mm Turning length: 4500 mm Turret positions: 1 Positions ATC: 142   Number controlled axis: 7   CNC Brand: Siemens CNC Model: 840D NILES SIMMONS N50/2 MC  TURN MILL DRILL MACHINING Make            : NILES SIMMONS Germany Typ            &nbs p; : N 50 / 2 MC x 4500 Age            &nbs p; : 2008   Swing over slide              : 1.250 Swing over bed               : 1.300 DBC turning length          : 4.500 Spindle bore     &nb ...

Vertical Lathe WMW NILES DMF 6300 Condition: Very good, complete Technical details: Turning diameter: 6300 mm Turning diameter, with side-support: 6000 mm Degrees displacement of the vert. supports: +/-30 ° Displacement of the side-support: 1800 mm Workpiece height max. : 2500 mm Workpieceweight max. : 50000 kg Chuck diameter: 5300 mm Speedrange: 0.35-14 rpm Feeding speeds (16): 0.063-11.2 mm/omw. Rapid speed of the supports: 1000 mm/min ¬ ¹ Rapid speed of the side-support: 500 mm/min ¬ ¹ Connection power: 120 kW Dimensions of the machine W: 14.40 x 8.20 x 8.70 m Weight of the machine ca.: 174.000 kg

Code 151295 Description Facinglathe with center Make WMW NILES Model DP 1 / S 2 Serial number 261 526 149 Year of make 1986 Max. centerheight over base plate 1250 mm Max. swing over base plate 2480 mm Max. swing in Gap 3100 mm Distance between centers 4000 mm Max. workpiece weight betw. centers 10.000 kgs Spindle bore 100 mm Movement slide ( max. ) 1000 ( + 750 ) mm crossslide 630 mm toolslide 200 mm 18 Speeds 5,6 – 280 rpm Motorpower 45 kW Total power 55 kVA Machine weight total ± 18000 kgs Accessoiries 4 chuck facingplate of Ø 1250 mm Condition Machine is in very good condition

Parallel lathe NILES DLZ 400 IV Between points: 1000 mm Maxi Ø on bench: 420 mm Maxi Ø over saddle: 225 mm Spindle diameter: Ø 52 mm Spindle speed: from 45 to 2240 RPM 3-jaws chuck Ø 250 mm (interchangeable jaws) Threadings: Metric + Whitworth Tailstock: CM5 Rapid on X Lubricant pump Voltage: 380 V Length: 3000 mm Depth: 1500 mm Total height: 1600 mm Weight: approx 2,5 T

Gear milling machine / gear hobbing machine make NILES type RF 6 M 15Lizensbau Pfauter Chemnitz, year of construction unfortunately not visibleTechnical specifications:Wheel diameter to be milled for spur gears: 1500 mmmax. Milling to be milled: 15 Mod.Range of helical gear drm. at10 ° spiral approx.: 1500 mm20 ° spiral approx.: 1500 mm30 ° spiral approx: 1350 mm40 ° spiral approx.: 1060 mm45 ° spiral approx: 900 mm50 ° spiral "750 mm60 ° spiral approx.: 450 mmBurr turns per minute: 20-26-33-43-56-71-90-118gr. Outer diameter of the milling cutter: 200 mmDrm. Milling mandrels: 27-32-40 mmDrm. of the workpiece clamping mandrel: 60 mmRotation of the drive pulley on the machine per minute: 520Drm. the drive pulley on the machine: 500 mmWidth of the drive pulley on the machine: 130 mmPower requirement: 10 hpRotation of the engine: approx. 1000 rpmExternal dimensions of the machine: 320 ...

Manufacturer Niles Model ZSTZ 1250 Year 1986 Maximum wheel diameter : 1250 mm Module + : 30

NILES lathe turning diameter approx. 700 mm turning length 1000 mm including new measurement. The machine is in good technical condition, it is possible to test it by agreement.

WMW Niles DLZ Ø 630 x 2000 mm Distance between centers: 2000 mm Swing over bed: 630 mm Swing over cross-slide: 400 mm Swing in gap: 720 mm Diametre of main spindle bore: 72 mm Power on main spindle: 19 kW Number of speeds: 28 > 1400 rpm Total power needed: 220V Weight: 4,8 ton

CNC Machining Center for turning and milling NILES SIMMONS Type of machine N 50 MC x 6000 Year of manufacture 2009. Never used. Control system Siemens Sinumerik 840 D Workpiece spindle: B20 Spindle bore diameter: 225 mm Spindle diameter in front bearing: 360 mm Swing over cross slide: 1250 mm Cutting diameter over bed: 1300 mm Working height: 1700 mm Turning length 6000 mm Spindle drive 78 / 87 kW

Control Unit, Control Electronics, Numerical Control WMW, NILES TDR 100-01 ( TDR100-01 ) Input: 380 V AC 35 A 49 - 62 Hz Output: 270 V DC 25 A IP 00 New ! Dimensions: 250 x 160 x 160 mm

Control Unit, Control Electronics, Numerical Control WMW, NILES TDR 700-223 ( TDR700-223 ) Input: 380 V 3AC 41 A 49 - 62 Hz Output: 400 V DC 50 A Ersatzteil u.Ersatzteil u.a. for milling machine AUERBACH FkrSRS 250 CNC-H 646 ! used, tested ! Dimensions: 315 x 270 x 200 mm

Control unit, control electronics, numerical control WMW, NILES 70.1011 1x PCB: 70.1011-13:1B/1 1x PCB: 70.1011-9:1B/1 1x PCB: 70.1011-11:1B/1 used, spare parts dispenser ! Dimensions: 250 x 160 x 160 mm

3-jaw chuck, three-jaw chuck, lathe chuck WMW NILES outer Ø: 250 mm bore Ø:80 bolt circle: 180 mm flange: 220 mm height with jaws: 110 mm 2400 rpm with cross cone and camlock D1- 8 inch (stud M 16) 2 set of jaws (1x drill 1x rotary jaw set) 1 chuck wrench Dimensions: 250 x 250 x 195 mm

3- Jaw chuck WMW NILES DHK 200x3 Outer Ø: 200 mm Flange: 155 mm Bore Ø: 60 mm bolt circle: 175 mm Height with jaws: 125 mm feed number: 507 Dimensions: 200 x 200 x 125 mm

3-jaw chuck, three-jaw chuck, lathe chuck WMW NILES DH-B 315 x 3 x 6 outer Ø: 315 mm Bore Ø: 100 mm Height with jaws: 130 mm bolt circle: 33 / 290 mounting: M14 3 jaws extra Speed max.: 1800 rpm min. 20-240 mm max. 75-240 mm complete with inner and outer jaws Dimensions: 315 x 315 x 150 mm

BRAND: NILES YEAR: 1988 MODEL: DFS2-2 APPLICATION TYPE: TURNING LOCATION: GERMANY MACHINE TYPE: LATHE AVAILABILITY: IMMEDIATELY Technical Information CONTROL UNIT BRAND: FAGOR MAIN DRIVE SPINDLE SPEED RANGE: 4000 1/MIN Additional Information MACHINE BENEFITS TECHNICAL MACHINE BENEFITS: - 12-FOLD TOOL CARRIER - HARDENED GUIDEWAYS - STANDARD ACCESSORIES - UP CATALOG - AIR FILTER FOR DC MOTOR - ADDITIONAL EQUIPMENT ACCORDING TO B1. 2/3 - THREE-PHASE CURRENT - OPERATING VOLTAGE 380 VOLT - FREQUENCY 50 HZ - DC

Precision four-jaw chuck, chuck, face plate, 4-jaw chuck -Manufacturer: WMW Niles, four-jaw chuck type DHK-B/8-250x4 -Chuck size: O 250 mm -Passage: O 80 mm -Bolt circle: O 135 mm -Intake: short taper 6 -Weight: 35kg

Grinding wheel, cup wheel, bench grinder, surface grinder, cylindrical grinder -Manufacturer: Niles, grinding wheel 20 Jot - Inside: Ø 32 mm -Outside: Ø 200 mm -Width: 20 mm -Weight: 1.3 kg